cadSysInvitedRangingRetries

CADANT-CMTS-SYSTEM-MIB · .1.3.6.1.4.1.4998.1.1.5.1.1.5
MIB view Table view

Object

scalar Integer32 
Number of retries on inviting ranging requests.  (ref 9.2.4)

Context

MIB
CADANT-CMTS-SYSTEM-MIB
OID
.1.3.6.1.4.1.4998.1.1.5.1.1.5
Type
scalar
Access
readonly
Status
current
Parent
cadSysParams
Siblings
56

Syntax

Integer32

Values & Constraints

Object Constraints
range: 16-16

Related Objects

Sibling Objects
ObjectTypeSyntaxOID
cadSysSyncInterval
Nominal time between transmission of SYNC messages. (ref 6.3.2)
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.1
cadSysT5Timeout
Wait for Upstream CHannel Change response.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.10
cadSysT6Timeout
Wait for REG-RSP and REG-ACK
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.11
cadSysMiniSlotSize
Size of mini-slotfor upstream transmission. Must be a power of 2 (in units of the Timebase Tick).
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.12
cadSysDSxRequestRetries
Number of Timeout Retries on DSA/DSC/DSD Requests.
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.13
cadSysDSxResponseRetries
Number of Timeout Retries on DSA/DSC/DSD Responses.
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.14
cadSysT7Timeout
Wait for DSA/DSC/DSD Response timeout.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.15
cadSysT8Timeout
Wait for DSA/DSC/DSD Acknowledge timeout.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.16
cadSysT9Timeout
Registration timeout, the time allowed between the CMTS sending a RNG-RSP(success) to a CM, and receiving a REG-REQ from that same CM.
scalarMinutes Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.17
cadSysT10Timeout
Wait for Transaction End timeout.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.18
cadSysT11Timeout
Wait for a DCC Response on the old channel.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.19
cadSysUCDInterval
Time between transmission of UCD messages. (ref 6.3.3)
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.2
cadSysT13Timeout
Maximum holding time for QOS resources for DCC.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.20
cadSysDCCREQRetries
Number of retries on Dynamic Channel Change Request.
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.21
cadSysMICEnable
Enable MIC checking on the CMTS.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.22
cadSysMICAuthString
Encrypted MIC Authentication
scalarOctetString.1.3.6.1.4.1.4998.1.1.5.1.1.23
cadSysAutoRecoveryEnable
Enable automatic recovery of card/port/software in case of component failure.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.24
cadSysActiveIpAddress
Ip Address of the active control complex.
scalarSNMPv2-SMIIpAddress.1.3.6.1.4.1.4998.1.1.5.1.1.25
cadSysSpOperMode
Special operational mode. Value of 1 indicates the mode is enabled. dqossf10cms - Allow 1.0 CMs to be stored in DocsQosServiceFlowEntry adjrxpwrctl - Allow rx power control to be…
scalarBits.1.3.6.1.4.1.4998.1.1.5.1.1.26
cadSysCountsCollectionRate
The period, in minutes, in which every count in the CMTS is to be collected. If this object is set to 0, counts collection will be disabled.
scalarUnsigned32.1.3.6.1.4.1.4998.1.1.5.1.1.27
cadSysMaxQoSActiveTimeout
Defines the maximum QoS Active Timeout the E6000 is willing to allow. If a larger value is received in a CM request the E6000 will return this value instead in the response (Refe…
scalarseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.28
cadSysMaxQoSAdmittedTimeout
Defines the maximum QoS Admitted Timeout the E6000 is willing to allow. If a larger value is received in a CM request the E6000 will return this value instead in the response (Re…
scalarseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.29
cadSysMaxMAPPending
The number of mini-slots that a CMTS is allowed to map into the future. (ref 6.3.4)
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.3
cadSysAllow10CmConcatenation
Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0 mode to utilize concatenation. If this value is false and a modem operating in 1.0 mode sends up a mo…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.30
cadSysAllow10CmFragmentation
Defines whether or not the E6000 will allow a modem operating in DOCSIS 1.0 mode to utilize fragmentation. If this value is false and a modem operating in 1.0 mode sends up a mo…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.31
cadSysPercentAddtlDsBwAllocated
This value of this setting is used to make a percentage increase to a dynamic downstream service flows maximum traffic rate. This is flexiblity actually causes the E6000 to oper…
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.32
cadSysMaxTrafBurstFor11CMs
This is the default value that will be used to populate the Maximum Traffic Burst for a 1.1 modem unless the maximum traffic burst TLV is explicitly provided in either the modems …
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.33
cadSysFanSpeedControlEnable obsolete
Enable automatic fan speed control.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.34
cadSysFlaplistPowerAdjustThreshold
The threshold is used to monitor the power adjust in the flap list. For a range request received that results in a power adjust exceeding the threshold value will cause the count…
scalardB Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.35
cadSysRemoteFSEnable
Indicates whether the active SCM should allow mounting the the filesystems of the standby SCM.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.36
cadSysRemotePortEnable
Indicates whether the active SCM should allow redirection of the serial console of the standby SCM.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.37
cadSysTcpSmoothingValue1D8U
TCP smoothing value to be programmed into hardware on 1D8U CAMs.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4998.1.1.5.1.1.38
cadSysTcpSmoothingValue2D12U
TCP smoothing value to be programmed into hardware on 2D12U CAMs.
scalarSNMPv2-SMIUnsigned32.1.3.6.1.4.1.4998.1.1.5.1.1.39
cadSysRangingInterval
Time between transmission of broadcast Ranging requests. (ref 7.3.3)
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.4
cadSysModemLossThreshold deprecated
Minimum modem threshold triggering detection of an upstream channel lockup.
scalarUnsigned32.1.3.6.1.4.1.4998.1.1.5.1.1.40
cadSysPeakTrafRateFor11CMs obsolete
This is the default value that will be used to populate the Peak Traffic Rate for a 1.1 modem configuration file unless the peak traffic rate is explicitly provided by a Service C…
scalarDOCS-QOS3-MIBBitRate.1.3.6.1.4.1.4998.1.1.5.1.1.41
cadSysCpeHostAuthorization
This variable enables the CPE Host Authorization feature.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.44
cadSysMaxUcdBurstLength
This variable limits the maximum UCD burst length.
scalarbytes Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.46
cadSysLO1LeakDetect
This variable controls LO1 leak detection on the DMM.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.47
cadMtcmConditionalOverride
If set to 'true', for a MAC Domain configured for MTCM enabled operation, the E6000 will set a registering MTCM-capable CM to be MTCM disabled (via REG-RSP message) unless at le…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.48
cadSysDelayedCpeLearning
This setting only applies to modems that have BPI enabled. When set to false(2), CPE learning is enabled during registration when BPI initialization is initiated for those mode…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.49
cadSysModPriDsInRccEnabled
Enable modifying primary Downstream channel in RCC of Reg-Rsp-MP. Refer ECN 690.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.52
cadSysSendTccRefIdPerFragment
Settings for sending the Transmit Channel Configuration (TCC) Reference sub-type 46.1 for type 46 TCC fragmentation. If 'true', sends 46.1 Ref ID in every type 46 TCC fragment; If…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.53
cadSysPeakTrRateUpstream
This object enables support for Peak Traffic Rate in the upstream direction.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.54
cadSysAllowAmbiguityOverride
This object enables ambiguity resolution channel-override actions.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.55
cadSysUnicastNpUsAcquisition
This object enables unicast non-primary upstream channel acquisition.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.56
cadSysMacMoveBlockedOnRcptDhcpPkt
MAC movement is blocked on receipt of DHCP packets
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.57
cadSysTftpProxy
This parameter provides a global enable for the TFTP Enforce and Dynamic Shared Secret features. In order for the cadIfMacDomainTftpEnforce and cadIfMacDomainDynamicSecret paramet…
scalarEnumeration.1.3.6.1.4.1.4998.1.1.5.1.1.58
cadSysFanSpeedLevel
Set the fan speed for the chassis.
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.59
cadSysRegistrationRequestRetries
Number of retries on registration requests/responses.
scalarInteger32.1.3.6.1.4.1.4998.1.1.5.1.1.6
cadSys1x1onCmAcPwrLossEnabled
This object enables/disables the CMTS reaction to a AC Power Loss CM-STATUS. If true, the CMTS will wait until cadSys1x1onCmAcPwrLossHoldoff expires, and then the CMTS will place…
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.60
cadSysFlapListInsertionThreshold
This object shows the number of seconds between successive ranging attempts that must pass before the modem is counted as flapped. The modem must have also been in a provisioning…
scalarseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.61
cadSysAES128Enable
Enables AES-128 Cryptography Suite for BPI+ when true.
scalarSNMPv2-TCTruthValue.1.3.6.1.4.1.4998.1.1.5.1.1.62
cadSysCMMAPProcessingTime
Time provided between arrival of the last bit of a MAP at a CM and effectiveness of that MAP. (ref 7.1.1)
scalarMicroseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.7
cadSysCMRangingResponseProcessingTime
Minimum tile allowed fro a CM following receipt of a rangin response before it is expected to reply to an invited ranging request.
scalarMilliseconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.8
cadSysCMConfiguration
Maximum time allowed for a CM, following receipt of a configuration file, to send a Registration Request to a CMTS.
scalarSeconds Integer32.1.3.6.1.4.1.4998.1.1.5.1.1.9