currSoftSaveAs – AT-SETUP-MIB – Observium MIB Browser

Object

scalar deprecated r/w SNMPv2-TCDisplayString

Set with a filename to save the currently running software to
the root of flash. Only one save operation can be executed at a
time across all SNMP users, and the filename must not contain
whitespace characters.
          
Immediately upon executing the set action, the actual firmware
save operation will be started and continue on the device until
it has completed or a failure occurs.
          
Subsequent reads of the object will return one of several
results:
          
saving x            A saving operation is currently in
                    progress. Another save cannot be started
                    while the object is returning this value.
          
x success           The last save operation was successfully
                    completed.
          
x failure: [error]  The last save operation failed, due to the
                    descriptive message attached. The most
                    common failure is lack of disk space.
          
idle                There is no save operation in progress and
                    a new one may be started.
          
Upon reading a success or failure message, the message will be
cleared and the next read will result in an 'idle' message. A
new save operation can now be executed.
          
NOTE: This object has been replaced by objects currSoftSaveToFile,
currSoftSaveStatus and currSoftLastSaveResult.

Context

MIB: AT-SETUP-MIB
OID: .1.3.6.1.4.1.207.8.4.4.4.500.2.1.3
Type: scalar
Access: readwrite
Status: deprecated
Parent: currentFirmware

Net-SNMP examples

How SNMP and these commands work

Scalars have one instance, identified by the .0 suffix.

Read the scalar instance

/usr/bin/snmpget -v2c -c '<community>' -Pud -Ir -OQUv -m 'AT-SETUP-MIB' -M '/opt/observium/mibs/allied:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'AT-SETUP-MIB::currSoftSaveAs.0'

More examples

Translate to a numeric OID

/usr/bin/snmptranslate -Pud -Ir -On -m 'AT-SETUP-MIB' -M '/opt/observium/mibs/allied:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'AT-SETUP-MIB::currSoftSaveAs'

Syntax

SNMPv2-TCDisplayString

Source: SNMPv2-TCDisplayString
Base type: OctetString
Display format: 255a

Type Description

Represents textual information taken from the NVT ASCII
          
character set, as defined in pages 4, 10-11 of RFC 854.
          
To summarize RFC 854, the NVT ASCII repertoire specifies:
          
  - the use of character codes 0-127 (decimal)
          
  - the graphics characters (32-126) are interpreted as
    US ASCII
          
  - NUL, LF, CR, BEL, BS, HT, VT and FF have the special
    meanings specified in RFC 854
          
  - the other 25 codes have no standard interpretation
          
  - the sequence 'CR LF' means newline
          
  - the sequence 'CR NUL' means carriage-return
          
  - an 'LF' not preceded by a 'CR' means moving to the
    same column on the next line.
          
  - the sequence 'CR x' for any x other than LF or NUL is
    illegal.  (Note that this also means that a string may
    end with either 'CR LF' or 'CR NUL', but not with CR.)
          
Any object defined using this syntax may not exceed 255
characters in length.

Values & Constraints

Type Constraints

range: 0..255