h3cDot11RRMCfgPERThres
A3COM-HUAWEI-DOT11-RRM-MIB ·
.1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.11
Object
column
r/w
percent Integer32
Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.
Context
- MIB
- A3COM-HUAWEI-DOT11-RRM-MIB
- OID
.1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.11- Type
- column
- Access
- readwrite
- Status
- current
- Units
- percent
- Parent
- h3cDot11RRMRadioCfgEntry
- Table
- h3cDot11RRMRadioCfgTable
- Siblings
- 12
Syntax
percent Integer32
Values & Constraints
Object Constraints
range: 10-100
Related Objects
Sibling Objects
| Object | Type | Syntax | OID |
|---|---|---|---|
| h3cDot11RRMRadioType 802.11 radio type. | column | A3COM-HUAWEI-DOT11-REF-MIBH3cDot11RadioType | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.1 |
| h3cDot11RRMCfgNoiseThres Configure the noise threshold. | column | Integer32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.10 |
| h3cDot11RRMCfgToleranceFctr Configure the tolerance level.
During dynamic frequency selection (DFS), the channel will be changed
only if there is a better channel having lesser interference and packet
error … | column | percent Integer32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.12 |
| h3cDot11RRMCfgAdjacencyFctr Configure the adjacency factor for the band.
If transmit power control (TPC) is configured, power will be adjusted
when the nth neighbor is detected. The value n is the adjacency… | column | Integer32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.13 |
| h3cDot11RRMCfgChlState Enable/Disable dynamic channel selection. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.2 |
| h3cDot11RRMCfgChlMode Configure the mode of channel selection.
This node can be configured only when dynamic channel selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.3 |
| h3cDot11RRMChlProntoRadioElmt Specify the AP and radio that will change channel at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of c… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.4 |
| h3cDot11RRMCfgPwrState Enable/Disable dynamic power selection for the band. | column | SNMPv2-TCTruthValue | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.5 |
| h3cDot11RRMCfgPwrMode Configure the mode of transmit power control.
This node can be configured only when dynamic power selection
is enabled. | column | Enumeration | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.6 |
| h3cDot11RRMPwrProntoRadioElmt Specify the AP and radio that will change power at next
calibration cycle.
0 is returned when getting the value of this node.
This node can be configured only when the mode of tra… | column | SNMPv2-SMIUnsigned32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.7 |
| h3cDot11RRMCfgIntrvl Configure the calibration interval. | column | minute SNMPv2-SMIInteger32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.8 |
| h3cDot11RRMCfgIntrfThres Configure the interface threshold.
By default, interference observed on an operating channel is considered
during dynamic frequency selection and transmit power control. If the
i… | column | percent Integer32 | .1.3.6.1.4.1.43.45.1.10.2.75.8.1.2.1.9 |