ZTE-DSL-LINE-EXT-MIB Table View

Adsl line additional information table.

zxAdslLineEntry row .1.3.6.1.4.1.3902.1004.4.1.1.1

Adsl line additional information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslLinePMConfPMSF This configuration parameter defines the line states to be forced by the near-end ATU on this line. It is coded as an integer value with following definition: L0_FullOn Force the line to transition from the L3 i…	Enumerationr/w Enumerated Values: 1 l0_FullOn 3 l2_LowPower 4 l3_Idle	.1.3.6.1.4.1.3902.1004.4.1.1.1.1
zxAdslLinePMState The Line has four possible power management states, numbered 0 to 3 and corresponding to respectively: L0 - Synchronized - This Line state (L0) is when the Line has full transmission (i.e. …	Enumeration Enumerated Values: 1 l0_FullOn 2 l1_LowPower 3 l2_LowPower 4 l3_Idle	.1.3.6.1.4.1.3902.1004.4.1.1.1.2
zxAdslLineDMTTrellisdeprecated Parameter that indicates whether trellis coding has been enabled or disabled.Trellis coding should always be enabled for its clear performancen advantage.Trellis coding is mandatory for ADSL/ADSL2plus.	Enumeration Enumerated Values: 0 unknown 1 on 2 off	.1.3.6.1.4.1.3902.1004.4.1.1.1.3
zxAdslLineTxAtmCells Transmitted ATM cell counter.This is a count of total data cells only transmitted by ATU-C.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.1.1.4
zxAdslLineRxAtmCells Received ATM cell counter.This is a count of total data cells only received by ATU-C.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.1.1.5
zxAdslLineIdleCells Number of idle cells transmitted/recieved by ATU-C.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.1.1.6
zxAdslLineTxDataRate Transmitted net data rate on this line.	kbpsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.1.1.7
zxAdslLineRxDataRate Recieved net data rate on this line.	kbpsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.1.1.8

Adsl line config profile extended information table.

zxAdslLineConfProfileExtEntry row .1.3.6.1.4.1.3902.1004.4.1.2.1

An entry extends the adslLineConfProfileEntry defined in
[RFC2662]. Each entry corresponds to an ADSL line profile.

Indexes

No indexes recorded

Column	Syntax	OID
zxAdslLineDMTConfTrellisdeprecated Parameter that enable or disable trellis coding. Trellis coding should always be enabled for its clear performancen advantage. Trellis coding is mandatory for ADSL/ADSL2plus. The value on(1) is default for all Annexes …	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.3902.1004.4.1.2.1.1
zxAdslAtucConfMaxBitsPerBin Specifies maximum Rx number of bits per bin.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.3902.1004.4.1.2.1.2
zxAdslAtucConfTxStartBin Specifies lowest bin number allowed for Tx signal. Different line coding type has different default value. 0x20 (default for Annex A only) 0x20 (default for ADSL2/ADSL2plus) 0x06 (default for Annex A if G.Span …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.2.1.3
zxAdslAtucConfTxEndBin Specifies highest bin number allowed for Tx signal. Default = 0x3ff (default for all Annexes and ADSL2/ADSL2plus)	Integer32r/w Constraints: range: 0-512	.1.3.6.1.4.1.3902.1004.4.1.2.1.4
zxAdslAtucConfRxStartBin Specifies lowest bin number allowed for Rx signal. Different line coding type has different default value. 0x06 (default for Annex A) 0x01 (default for Annex B) 0x06 (default for Annex C/C.x) 0x06 (default f…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.2.1.5
zxAdslAtucConfRxEndBin Specifies highest bin number allowed for Rx signal. Default = 0x3f (default for all Annexes and ADSL2/ADLS2plus)	Integer32r/w Constraints: range: 0-512	.1.3.6.1.4.1.3902.1004.4.1.2.1.6
zxAdslAtucConfUseCustomBins Enable or disable custom bin selection for upstream/downstream transmission. This parameter is used in conjunction with the adslAtucDMTConfFreqBins and adslAturDMTConfFreqBins[ADSL-DMT-LINE-MIB] parameter.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.3902.1004.4.1.2.1.7
zxAdslAtucConfDnBitSwap enables/disables downstream bit swapping. Different line coding type has different default value. disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C C.x, G.Span/ADSL+ and G.Span Plus) en…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.3902.1004.4.1.2.1.8
zxAdslAtucConfUpBitSwap enables/disables upstream bit swapping. Different line coding type has different default value. disable(2) (default for ADSL2/ADLS2plus, Annex B, Annex C C.x, G.Span/ADSL+ and G.Span Plus) enab…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.3902.1004.4.1.2.1.9
zxAdslAtucConfREADSL2Enabledeprecated Defines whether downstream READSL2 operation should be forced by the ATU-C.	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.3902.1004.4.1.2.1.10
zxAdslAtucConfPsdMaskType It is supported by G.Span. Dsl card team will provide files about it in details.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.2.1.11
zxAdslAtucConfPMMode This configuration parameter defines the line states the ATU-C may autonomously transition to on this line. It is coded in a bit map representation (0 if not allowed, 1 if allowed) with following definition: Bit 0…	Bitsr/w Enumerated Values: 0 idle 1 lowPower	.1.3.6.1.4.1.3902.1004.4.1.2.1.12
zxAdslAtucConfPML0Time PM configuration parameter,related to the L2 low power state. This parameter represents the minimum time between an exit from the L2 state and the next entry into the L2 state.	secondsInteger32r/w Constraints: range: 0-255	.1.3.6.1.4.1.3902.1004.4.1.2.1.13
zxAdslAtucConfPML2Time PM configuration parameter,related to the L2 low power state. This parameter represents the minimum time between an entry into the L2 state and the first Power Trim in the L2 state and between two consecutive Power Tri…	secondsInteger32r/w Constraints: range: 0-255	.1.3.6.1.4.1.3902.1004.4.1.2.1.14
zxAdslAtucConfPML2ATPR PM configuration parameter,related to the L2 low power state. This parameter represents the Maximum Aggregate Transmit Power Reduction (in dB) that can be performed through a single Power Trim in the L2 state. It range…	dBInteger32r/w Constraints: range: 0-31	.1.3.6.1.4.1.3902.1004.4.1.2.1.15
zxAdslAtucConfPML2Rate PM configuration parameter,related to the L2 low power state. This parameter specifies the minimum net data rate during the low power state (L2).	kbpsInteger32r/w Constraints: range: 256-1024	.1.3.6.1.4.1.3902.1004.4.1.2.1.16
zxAdsl2ConfMinProtectionDs Minimum Impulse Noise Protection on Downstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols. The parameter can take the following values: noProtection (i.e., INP not req…	symbolsEnumerationr/w Enumerated Values: 1 noProtection 2 halfSymbol 3 singleSymbol 4 twoSymbols 5 fourSymbols 6 eightSymbols 7 sixteenSymbols	.1.3.6.1.4.1.3902.1004.4.1.2.1.20
zxAdsl2ConfMinProtectionUs Minimum Impulse Noise Protection on Upstream direction. The minimum impulse noise protection for the bearer channel, expressed in symbols.	symbolsEnumerationr/w Enumerated Values: 1 noProtection 2 halfSymbol 3 singleSymbol 4 twoSymbols 5 fourSymbols 6 eightSymbols 7 sixteenSymbols	.1.3.6.1.4.1.3902.1004.4.1.2.1.21

This table provides one row for each ATUC
Each row contains the Physical Layer Parameters
table for that ATUC. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).

zxAdslAtucPhysEntry row .1.3.6.1.4.1.3902.1004.4.1.3.1

Adsl physical layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAtucPrevSnrMgn The adslAtucCurrSnrMgn at the time of the last linkup event.	tenth dBInteger32 Constraints: range: -640-640	.1.3.6.1.4.1.3902.1004.4.1.3.1.1
zxAdslAtucPrevAtn The adslAtucCurrAtn at the time of the last linkup event.	tenth dBUnsigned32 Constraints: range: 0-630	.1.3.6.1.4.1.3902.1004.4.1.3.1.2
zxAdslAtucPrevAttainableRate The adslAtucCurrAttainableRate at the time of the last linkup event.	kbpsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.3.1.3
zxAdslAtucChipVersiondeprecated The atuc chip version number.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.3902.1004.4.1.3.1.4

This table provides one row for each ATUR
Each row contains the Physical Layer Parameters
table for that ATUR. ADSL physical interfaces are
those ifEntries where ifType is equal to adsl(94).

zxAdslAturPhysEntry row .1.3.6.1.4.1.3902.1004.4.1.4.1

Adsl physical layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAturPrevSnrMgn The adslAturCurrSnrMgn at the time of the last linkup event.	tenth dBInteger32 Constraints: range: -640-640	.1.3.6.1.4.1.3902.1004.4.1.4.1.1
zxAdslAturPrevAtn The adslAturCurrAtn at the time of the last linkup event.	tenth dBUnsigned32 Constraints: range: 0-630	.1.3.6.1.4.1.3902.1004.4.1.4.1.2
zxAdslAturPrevAttainableRate The adslAturCurrAttainableRate at the time of the last linkup event.	kbpsSNMPv2-SMIGauge32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.4.1.3

This table provides one row for each Atuc channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).

zxAdslAtucChanEntry row .1.3.6.1.4.1.3902.1004.4.1.5.1

Adsl channel layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAtucChanRsSymbols The number of DMT symbols per ReedSolomon code word (S) in the upstream direction. Note that S is not restricted to interleaved mode only. This parameter is calculated differently for G.992.3 and G.992.5.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.5.1.1
zxAdslAtucChanRsDepth This parameter indicates interleaving depth (D) in the upstream direction. Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.5.1.2
zxAdslAtucChanRsRedundancy The number of redundant bytes (R) per Reed-Solomon code in the upstream direction.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.5.1.3

This table provides one row for each ATUR channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).

zxAdslAturChanEntry row .1.3.6.1.4.1.3902.1004.4.1.6.1

Adsl channel layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAturChanRsSymbols The number of DMT symbols per ReedSolomon code word (S) in the upstream direction. Note that S is not restricted to interleaved mode only. This parameter is calculated differently for G.992.3 and G.992.5.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.6.1.1
zxAdslAturChanRsDepth This parameter indicates interleaving depth (D) in the upstream direction. Note that D is not restricted to interleaved mode only. Even in fast mode, D is a valid constant value and is equal to 1.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.6.1.2
zxAdslAturChanRsRedundancy The number of redundant bytes (R) per Reed-Solomon code in the upstream direction.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.6.1.3

This table provides one row for each Atuc channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).

zxAdslAtucChanPerfEntry row .1.3.6.1.4.1.3902.1004.4.1.7.1

DMT channel layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAtucChanPerfNcd Count of no cell delineation (ncd) on this channel.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.1
zxAdslAtucChanPerfOcd Count of out of cell delineation (ocd) on this channel.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.2
zxAdslAtucChanPerfHec Header error check counter (hec) on this channel.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.3
zxAdslAtucChanPerfCurr15Ncd Count of no cell delineation (ncd) on this channel within the current 15 minute time interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.4
zxAdslAtucChanPerfCurr15Ocd Count of out of cell delineation (ocd) on this channel within the current 15 minute time interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.5
zxAdslAtucChanPerfCurr15Hec Header error check counter (hec) on this channel within the current 15 minute time interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.6
zxAdslAtucChanPerfCurr1DayNcd Count of no cell delineation (ncd) on this channel within the current 1 day interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.7
zxAdslAtucChanPerfCurr1DayOcd Count of out of cell delineation (ocd) on this channel within the current 1 day interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.8
zxAdslAtucChanPerfCurr1DayHec Header error check counter (hec) on this channel within the current 1 day interval	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.9
zxAdslAtucChanPerfPrev1DayNcd Count of no cell delineation (ncd) on this channel within the most recent previous 1-day period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.10
zxAdslAtucChanPerfPrev1DayOcd Count of out of cell delineation (ocd) on this channel within the most recent previous 1-day period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.11
zxAdslAtucChanPerfPrev1DayHec Header error check counter (hec) on this channel within the most recent previous 1-day period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.7.1.12

This table provides one row for each Atur channel.
ADSL channel interfaces are those ifEntries
where ifType is equal to adslInterleave(124)
or adslFast(125).

zxAdslAturChanPerfEntry row .1.3.6.1.4.1.3902.1004.4.1.8.1

DMT channel layer line actuals information entry

Indexes

IF-MIBifIndex

Column	Syntax	OID
zxAdslAturChanPerfNcd Count of no cell delineation (ncd) on this channel.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.1
zxAdslAturChanPerfHec Header error check counter (hec) on this channel.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.2
zxAdslAturChanPerfCurr15Ncd Count of no cell delineation (ncd) on this channel within the current 15 minute time interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.3
zxAdslAturChanPerfCurr15Hec Header error check counter (hec) on this channel within the current 15 minute time interval	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.4
zxAdslAturChanPerfCurr1DayNcd Count of no cell delineation (ncd) on this channel within the current 1 day interval.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.5
zxAdslAturChanPerfCurr1DayHec Header error check counter (hec) on this channel within the current 1 day interval	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.6
zxAdslAturChanPerfPrev1DayNcd Count of no cell delineation (ncd) on this channel within the most recent previous 1-day period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.7
zxAdslAturChanPerfPrev1DayHec Header error check counter (hec) on this channel within the most recent previous 1-day period.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.3902.1004.4.1.8.1.8

This table provides one row for each DSL line tesing.

zxDslLoopTestEntry row .1.3.6.1.4.1.3902.1004.4.1.9.1

DSL line tesing information entry

Indexes

zxDslLoopTestPort

Column	Syntax	OID
zxDslLoopTestPort Dsl port number.It should be equal to ifIndex in DSL layer.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.1
zxDslLoopTestType This is loop test action expected.	Enumerationr/w Enumerated Values: 0 noOper 1 cancle 2 utopia 3 afe 4 hybrid 5 atuc_OAM 6 atur_OAM	.1.3.6.1.4.1.3902.1004.4.1.9.1.2
zxDslLoopTestOperStatus This is loop test operational status. Note: if zxDslLoopTestOperStatus equal to Excuting(1), ifOperStaus should be tesing(3).	Enumeration Enumerated Values: 0 neverExcute 1 excuting 2 excuted 3 faliedToCommit	.1.3.6.1.4.1.3902.1004.4.1.9.1.3
zxDslLoopTestConfParam1 Configuration param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. For DSL8220v2.x: zxDslLoopTestType zxDslLoopTestConfParam1 --…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.5
zxDslLoopTestConfParam2 Configuration param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.6
zxDslLoopTestConfParam3 Configuration param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.7
zxDslLoopTestConfParam4 Configuration param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.8
zxDslLoopTestConfParam5 Configuration param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.9
zxDslLoopTestResultParam1 Loop test result param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. For DSL8220v2.x: zxDslLoopTestType zxDslLoopTestConfParam1 …	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.10
zxDslLoopTestResultParam2 Loop test result param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.11
zxDslLoopTestResultParam3 Loop test result param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.12
zxDslLoopTestResultParam4 Loop test result param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.13
zxDslLoopTestResultParam5 Loop test result param for some looptest.Its definition may be deferent according to the zxDslLoopTestType value and device type. No looptest uses this param now.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.9.1.14
zxDslLoopTestRowStatus Loop test table RowStatus .	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.3902.1004.4.1.9.1.15

Adsl line alarm config profile extended information table.
The cycle of thresholds monitoring shoul be less than 5 minutes.

zxAdslLineAlarmConfProfileExtEntry row .1.3.6.1.4.1.3902.1004.4.1.20.1

An entry extends the adslLineAlarmConfProfileEntry defined in
[RFC2662]. Each entry corresponds to an ADSL line alarm profile.

Indexes

No indexes recorded

Column	Syntax	OID
zxAdslAtucConnRateTolerance Tolerance between configured adslAtucChanConfInterleaveMaxTxRate and actual adslAtucChanCurrTxRate. Calculation: 100*(adslAtucChanConfInterleaveMaxTxRate - adslAtucChanCurrTxR…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.1
zxAdslAturConnRateTolerance Tolerance between configured adslAturChanConfInterleaveMaxTxRate and actual adslAturChanCurrTxRate. Calculation: 100*(adslAturChanConfInterleaveMaxTxRate - adslAturChanCurrTxR…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.2
zxAdslThreshAtucConnRate Threshold of Atuc connection rate. If adslAtucChanCurrTxRate is lower than zxAdslThreshAtucConnRate, zxAdslAtucConnRateOverThreshTrap trap will be sent. A value of `0' will disable the trap.	kbpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.20.1.3
zxAdslThreshAturConnRate Threshold of Atur connection rate. If adslAturChanCurrTxRate is lower than zxAdslThreshAturConnRate, zxAdslAturConnRateOverThreshTrap trap will be sent. A value of `0' will disable the trap.	kbpsInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3902.1004.4.1.20.1.4
zxAdslThreshAtucBandwidthUtil Threshold of Atuc bandwidth utilization. Calculation: Delta(ifOutOctets)*8*1024*100 Atuc Utilization = ------------------------------------------------…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.5
zxAdslThreshAturBandwidthUtil Threshold of Atur bandwidth utilization. Calculation: Delta(ifInOctets)*8*1024*100 Atur Utilization = -------------------------------------------------…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.6
zxAdslThreshAtucPacketLossRate The percentage of lost packets to total packets received on the Atuc interface. Calculation: ifOutDiscards*100 Atuc PacketLossRate = ------------------------------…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.7
zxAdslThreshAturPacketLossRate The percentage of lost packets to total packets received on the Atur interface. Calculation: ifInDiscards*100 Atur PacketLossRate = ------------------------------…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.8
zxAdslThreshAtucBlockErrorRate The percentage of adslAtucChanUncorrectBlks to adslAtucChanReceivedBlks on the Atuc interface. If this threshold is across, zxAdslAtucBlockErrorRateOverThreshTrap trap will be sent. A value of `0' will disable the t…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.9
zxAdslThreshAturBlockErrorRate The percentage of adslAturChanUncorrectBlks to adslAturChanReceivedBlks on the Atur interface. If this threshold is across, zxAdslAturBlockErrorRateOverThreshTrap trap will be sent. A value of `0' will disable the t…	%Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.10
zxAdslThreshReservedMetric1 reserved threshold. A value of `0' will disable the trap.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.11
zxAdslThreshReservedMetric2 reserved threshold. A value of `0' will disable the trap.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.12
zxAdslThreshReservedMetric3 reserved threshold. A value of `0' will disable the trap.	Integer32r/w Constraints: range: 0-100	.1.3.6.1.4.1.3902.1004.4.1.20.1.13