ZHNWIRELESS Table View

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.1

wlBaseCfgEnable

Enable or disable the wireless adapter.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.2

wlBaseCfgBand

Broadcast band (e.g. 2.4GHz operation).

OctetString

.1.3.6.1.4.1.5504.2.5.46.1.1.1.3

wlBaseCfgChannel

The configured wifi channel number or 'auto' for
automatic selection of a channel with low interference.

WlChannelSelectionsr/w

Type Values:

1	channel1
2	channel2
3	channel3
4	channel4
5	channel5
6	channel6
7	channel7
8	channel8
9	channel9
10	channel10
11	channel11
12	channel12
13	channel13
14	auto

.1.3.6.1.4.1.5504.2.5.46.1.1.1.4

wlBaseCfgCurrentChannel

The actual wifi channel number in use.

WlChannelSelections

Type Values:

1	channel1
2	channel2
3	channel3
4	channel4
5	channel5
6	channel6
7	channel7
8	channel8
9	channel9
10	channel10
11	channel11
12	channel12
13	channel13
14	auto

.1.3.6.1.4.1.5504.2.5.46.1.1.1.5

wlBaseCfgBandwidth

Aggregate radio bandwidth.

OctetString

.1.3.6.1.4.1.5504.2.5.46.1.1.1.6

wlBaseCfgAutoScanTimer

When configured for auto mode, this timer value specifies how
often to re-analyze the spectrum to select a low interference
channel. Note: auto channel rescan will only occur when there
are no actively connected devices.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.7

wlBaseCfgMimoNEwc

Radio 802.11n Enhanced Wireless Consortium (EWC) mode:
auto(1)
disable(2)

WlMimoNEwcModesr/w

Type Values:

1	auto
2	disabled

.1.3.6.1.4.1.5504.2.5.46.1.1.1.8

wlBaseCfgMimoNRate

The configured Multiple Input Multiple Output (MIMO) 802.11n rate.
Enumeration of:
auto(1),
use54g(2),
rate6Dot5(3),
rate13(4),
rate19Dot5(5),
…

WlMimoNRatesr/w

Type Values:

1	auto
2	use54g
3	rate6Dot5M
4	rate13M
5	rate19Dot5M
6	rate26M
7	rate39M
8	rate52M
9	rate58Dot5M
10	rate65M
11	rate78M
12	rate104M
13	rate117M
14	rate130M

.1.3.6.1.4.1.5504.2.5.46.1.1.1.9

wlBaseCfgMimoNProtection

Multiple Input Multiple Output(MIMO) 802.11n protection mode.
Enumeration of:
off(1),
auto(2),

WlMimoNProtectionModesr/w

Type Values:

1	off
2	auto

.1.3.6.1.4.1.5504.2.5.46.1.1.1.10

wlBaseCfgNClientsOnly

Enable or disable the restriction of access to 802.11n
clients, only. When enabled, prevent 802.11b/g clients
from connecting.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.11

wlBaseCfg54gRate

The rate when the radio is operating in 802.11g mode. This
object only applies when the Multiple Input Multiple Output
(MIMO) 802.11n Rate is set to use54g(2). Enumeration of:
rate1M(1),
rate2M…

Wl54gMulticastRatesr/w

Type Values:

1	rate1M
2	rate2M
3	rate5Dot5M
4	rate6M
5	rate9M
6	rate11M
7	rate12M
8	rate18M
9	rate24M
10	rate36M
11	rate48M
12	rate54M
13	auto

.1.3.6.1.4.1.5504.2.5.46.1.1.1.12

wlBaseCfgMulticastRate

The rate for multicast traffic. Enumeration of:
rate1M(1),
rate2M(2),
rate5Dot5M(3),
rate6M(4),
rate9M(5),
rate11M(6),
rate12M(7),
rate18M(8),
rate24M(9),
rate36M(10),
rate48M(11),
rate54M(12)

Wl54gMulticastRatesr/w

Type Values:

1	rate1M
2	rate2M
3	rate5Dot5M
4	rate6M
5	rate9M
6	rate11M
7	rate12M
8	rate18M
9	rate24M
10	rate36M
11	rate48M
12	rate54M
13	auto

.1.3.6.1.4.1.5504.2.5.46.1.1.1.13

wlBaseCfgBasicRate

The rate when the radio is operating in basic 802.11b/g mode.
Enumeration of:
default(1), -- use the factory defaulted basic rate
all(2), -- allow all supported basic rates
rate1An…

WlBasicRatesr/w

Type Values:

1	default
2	all
3	rate1And2
4	stdRates

.1.3.6.1.4.1.5504.2.5.46.1.1.1.14

wlBaseCfgFragThreshold

The threshold at which packets are fragmented.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.15

wlBaseCfgRTSThreshold

The packet size of a request-to-send (RTS) transmission. A low
threshold implies RTS packets are sent more frequently, thus
requiring more bandwidth but ensuring packet transmission on
a busy network.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.16

wlBaseCfgDTIMInterval

The interval at which Delivery Traffic Indication Messages (DTIM)
are generated. A DTIM message notifies a wireless client that
a packet is waiting for tranmission.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.17

wlBaseCfgBeaconInterval

The interval at which Beacons are generated.

wlBaseCfgGlobalMaxClients

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.18

The maximum number of wireless client devices that may be simultaneously
connected to the radio. This value should include the sum total of all
clients on all active SSIDs.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.19

wlBaseCfgXPress

Enable or disable the XPress(TM) Technology.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.20

wlBaseCfgTxPowerPercent

The percentage of total power that should be used for data transmissions.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.1.1.21

wlBaseCfgWMMEnable

Enable or disable Wifi Multimedia. When set to TRUE, audio,
video and voice application data is prioritized over other network
traffic.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.22

wlBaseCfgWMMNoAck

Enable or disable the suppression of acknowledgements for frames
that do not require a QOS Acknowledgement. This avoids the unnecessary
transmission of acknowledgements for highly time-critical data.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.23

wlBaseCfgWMMApsd

Enable or disable the Automatic Power Save Delivery (APSD) power
management method. This feature is useful for bi-directional applications,
such as VoIp phones.

wlBaseCfgWpsAddClientMethod

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.24

Configure the method of adding Clients:
pushButton(1),
accessPointPIN(2),
stationPIN(3)

WlWpsAddClientMethodr/w

Type Values:

1	pushButton
2	accessPointPIN
3	stationPIN

.1.3.6.1.4.1.5504.2.5.46.1.1.1.25

wlBaseCfgWpsApMode

Enable or disable WiFi Protected Setup (WPS) AP mode. If your provider
is using an external registrar for security, select true(1).
The PIN for AP mode is specified by the registrar. Provide this PIN to the
client. Sele…

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.26

wlBaseCfgWpsConfigAp

Start AP configuration. If your provider is using an external registrar
for security, wlBaseCfgWpsApMode then select true(1) to begin the
registration process with the client.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.27

wlBaseCfgWpsDevicePIN

Device PIN provided by external registrar.

OctetString

Constraints:
range: 8-8

.1.3.6.1.4.1.5504.2.5.46.1.1.1.28

wlBaseCfgWpsAddEnrollee

Start AP configuration. If wlBaseCfgWpsAddClientMethod is set for
pushButton(1), then the user must simultaneously push the WPS button
on the rear panel of the wireless zNID and set this object to true(1)
for push butto…

wlBaseCfgBridgeRestrictMode

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.29

wlBaseCfgWpsStationPIN

Station PIN provided by user.

OctetString

Constraints:
range: 8-8

.1.3.6.1.4.1.5504.2.5.46.1.1.1.30

Configure the bridge restriction mode:
enable(1),
enableScan(2),
disable(3),

WlBridgeRestrictModesr/w

Type Values:

1	enable
2	enableScan
3	disable

.1.3.6.1.4.1.5504.2.5.46.1.1.1.31

wlBaseCfgBridgeRefresh

Scans for any wireless bridge devices in range and displays them in
the Remote Bridge MAC Address table. Selecting true(1) will update the
wireless bridge devices in range. Wait for a few seconds for the update.

wlBaseCfgIndex wlVirtualIndex

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.1.1.32

wlVirtualIntfTable

table

.1.3.6.1.4.1.5504.2.5.46.1.2 · 1 row entry · 10 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlVirtualIntfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlVirtualIntfTable'

Table of Wireless Virtual LAN Interface Configuration, Status and Statistics objects.

wlVirtualIntfEntry row .1.3.6.1.4.1.5504.2.5.46.1.2.1

Entries in Wireless Vitrual LAN Interface Table.

Indexes

Column Syntax OID

wlVirtualIndex

Basic access point interface index. Guest (or Virtual) access points begin
with index = 2.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.2.1.1

wlVirtualHide

Enable or disable the suppression of the advertising of the access point's SSID.
If enabled, clients will need to configure the SSID to associate.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.2.1.2

wlVirtualAPIsolation

Enable or disable the isolation of clients by enabling or disabling secure
forwarding mode. This will preventpreventing one client from sending packets
directly to another client. All packets are forwarded upstream on …

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.2.1.3

wlVirtualDisableWme

Enable or disable the Wireless Multi-Media mode.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.2.1.4

wlVirtualEnableWmf

Enable or disable Wireless Multicast Forwarding.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.2.1.5

wlVirtualSsid

Configure the Primary SSID assigned to the wl0 interface,
or the Guest SSIDs assigned to the virtual wireless
interfaces.

OctetStringr/w

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.2.1.6

wlVirtualBssMacAddr

MAC Address assigned to the primary SSID.

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

Represents an 802 MAC address represented in the
`canonical' order defined by IEEE 802.1a, i.e., as if it
were transmitted least significant bit first, even though
802.5 (in contrast to other 802.x protocols) requires M…

.1.3.6.1.4.1.5504.2.5.46.1.2.1.7

wlVirtualCountryCode

Two character country code. The country code is automatically configured
based upon the model number of the unit. All countries with 100mW EIRP
maximum transmit power use the United Kingdom country code. North American…

WlCountryCodes

Type Constraints:
range: 2

.1.3.6.1.4.1.5504.2.5.46.1.2.1.8

wlVirtualMaxClients

Maximum number of client devices that may be simultaneously connected
to this SSID. The maximum clients value assigned to each access points
must not exceed the global maximum clients value.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.2.1.9

wlVirtualEnable

Enable or disable a single Wireless Virtual LAN Interface

wlBaseCfgIndex wlVirtualIndex

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.2.1.10

wlSecurityTable

table

.1.3.6.1.4.1.5504.2.5.46.1.3 · 1 row entry · 24 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlSecurityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlSecurityTable'

Table of Wireless Security Configuration, Status and Statistics objects
for virtual LAN interfaces.

wlSecurityEntry row .1.3.6.1.4.1.5504.2.5.46.1.3.1

Table of entries, per virtual LAN interface, of Wireless Security objects.

Indexes

Column Syntax OID

wlSecuritySsid

The primary SSID assigned to the wl0 interface,
or the Guest SSIDs assigned to this virtual wireless
interface.

OctetString

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.3.1.1

wlSecurityWps

Enable or disable WiFi Protected Setup (WPS) security method. If
WPS is disabled, the network authentication method, the data encryption,
and network key should also be configured in order to authenticate to
this wire…

wlSecurityCurrentWepKeyIndex64

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.3.1.2

wlSecurityAuthMode

Configure the network authentication method:
mode8011x(1),
open(2),
shared(3),
wpa(4),
wpa2(5),
wpaPsk(6),
wpa2Psk(7),
mixedWpa2Wpa(8),
mixedWpa2WpaPsk(9)

WlAuthenticationModesr/w

Type Values:

1	mode8011x
2	open
3	shared
4	wpa
5	wpa2
6	wpaPsk
7	wpa2Psk
8	mixedWpa2Wpa
9	mixedWpa2WpaPsk

.1.3.6.1.4.1.5504.2.5.46.1.3.1.3

wlSecurityWpaPsk

WPA/WPAI Passphrase. This field cannot contain a SPACE and is
returned as a string of asterisks.

OctetStringr/w

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.3.1.4

wlSecurityWpaGTKRekey

WPA Group Rekey Interval.

Unsigned32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.5504.2.5.46.1.3.1.5

wlSecurityWpaMode

WPA/WAPI Encryption mode:
tkip(1),
aes(2),
tkipAes(3)

WlWpaModesr/w

Type Values:

1	tkip
2	aes
3	tkipAes

.1.3.6.1.4.1.5504.2.5.46.1.3.1.6

wlSecurityWepStatus

Status of Wireless Encryption Protocol (WEP) encryption:
disabled(1)
enabled(2)

WlWepModesr/w

Type Values:

1	disabled
2	enabled

.1.3.6.1.4.1.5504.2.5.46.1.3.1.7

wlSecurityRadiusServerIP

IP address of the Remote Authentication Dial In User Server (RADIUS)
used for 802.1x authentication.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.5504.2.5.46.1.3.1.8

wlSecurityRadiusPort

UDP port to use for accessing the Remote Authentication Dial In User
Server (RADIUS).

Unsigned32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.5504.2.5.46.1.3.1.9

wlSecurityRadiusKey

Remote Authentication Dial In User Server (RADIUS) authentication key.
This field cannot contain a SPACE and is returned as a string of asterisks.

OctetStringr/w

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.3.1.10

wlSecurityWepKey

Security encryption strength:
bit64(1)
bit128(2)

WlSecurityKeyCodesr/w

Type Values:

1	bit64
2	bit128

.1.3.6.1.4.1.5504.2.5.46.1.3.1.11

Index into array of 64-bit encryption keys.

Unsigned32r/w

Constraints:
range: 1-4

.1.3.6.1.4.1.5504.2.5.46.1.3.1.12

wlSecurityCurrentWepKeyIndex128

Index into array of 128-bit encryption keys.

Unsigned32r/w

Constraints:
range: 1-4

.1.3.6.1.4.1.5504.2.5.46.1.3.1.13

wlSecurityWep64Key1

WEP 64-bit encryption key 1 string, which must consist of 5 ASCII characters
or 10 hexadecimal digits.

OctetStringr/w

Constraints:
range: 5-10

.1.3.6.1.4.1.5504.2.5.46.1.3.1.14

wlSecurityWep64Key2

WEP 64-bit encryption key 2 string, which must consist of 5 ASCII characters
or 10 hexadecimal digits.

OctetStringr/w

Constraints:
range: 5-10

.1.3.6.1.4.1.5504.2.5.46.1.3.1.15

wlSecurityWep64Key3

WEP 64-bit encryption key 3 string, which must consist of 5 ASCII characters
or 10 hexadecimal digits.

OctetStringr/w

Constraints:
range: 5-10

.1.3.6.1.4.1.5504.2.5.46.1.3.1.16

wlSecurityWep64Key4

WEP 64-bit encryption key 4 string, which must consist of 5 ASCII characters
or 10 hexadecimal digits.

OctetStringr/w

Constraints:
range: 5-10

.1.3.6.1.4.1.5504.2.5.46.1.3.1.17

wlSecurityWep128Key1

WEP 128-bit encryption key 1 string, which must consist of 13 ASCII characters
or 26 hexadecimal digits.

OctetStringr/w

Constraints:
range: 13-26

.1.3.6.1.4.1.5504.2.5.46.1.3.1.18

wlSecurityWep128Key2

WEP 128-bit encryption key 2 string, which must consist of 13 ASCII characters
or 26 hexadecimal digits.

OctetStringr/w

Constraints:
range: 13-26

.1.3.6.1.4.1.5504.2.5.46.1.3.1.19

wlSecurityWep128Key3

WEP 128-bit encryption key 3 string, which must consist of 13 ASCII characters
or 26 hexadecimal digits.

OctetStringr/w

Constraints:
range: 13-26

.1.3.6.1.4.1.5504.2.5.46.1.3.1.20

wlSecurityWep128Key4

WEP 128-bit encryption key 4 string, which must consist of 13 ASCII characters
or 26 hexadecimal digits.

OctetStringr/w

Constraints:
range: 13-26

.1.3.6.1.4.1.5504.2.5.46.1.3.1.21

wlSecurityWpa2Preauth

Enable or disable WPA2 pre-authentication.

wlBaseCfgIndex wlVirtualIndex wlMACFilterIndex

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.3.1.22

wlSecurityWpa2NetReauth

Configure the WPA2 network re-authentication time, in seconds.

Unsigned32r/w

Constraints:
range: 0-604800

.1.3.6.1.4.1.5504.2.5.46.1.3.1.23

wlSecurityMACFilterMode

Configure the MAC Filter mode. The MAC Filter rules defined in the
wlMACFilterTable will be ignored when this object is set to disable(3).

WlMACFilterModesr/w

Type Values:

1	allow
2	deny
3	disable

.1.3.6.1.4.1.5504.2.5.46.1.3.1.24

wlMACFilterTable

table

.1.3.6.1.4.1.5504.2.5.46.1.4 · 1 row entry · 5 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlMACFilterTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlMACFilterTable'

Table of Wireless MAC filter rules for a virtual wireless interface.
The MAC Filter table contains a list of MAC addresses for devices that
are permitted to connect, or prevented from connecting to the wireless
service.

wlMACFilterEntry row .1.3.6.1.4.1.5504.2.5.46.1.4.1

Entries in the Wireless MAC filter rules for a virtual wireless interface.

Indexes

Column Syntax OID

wlMACFilterIndex

The Wireless MAC filter table index.

wlBaseCfgIndex wlStaticWdsMACIndex

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.4.1.1

wlMACFilterSsid

The primary SSID assigned to the wl0 interface,
or the Guest SSIDs assigned to this virtual wireless
interface.

OctetString

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.4.1.2

wlMACFilterMacAddr

The MAC address which to apply to the filter rule.

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.5504.2.5.46.1.4.1.3

wlMACFilterIfName

The virtual interface name to which this rule applies.

OctetString

Constraints:
range: 0-72

.1.3.6.1.4.1.5504.2.5.46.1.4.1.4

wlMACFilterRowStatus

The SNMP RowStatus of the current row. When creating a new
MAC Filter entry for a virtual wireless interface, only the
MAC Address must be specified. The wlVirtualIndex will
be used to determine the SSID and the filter…

Zhone-TCZhoneRowStatusr/w

Type Values:

1	active
4	createAndGo
6	destroy

.1.3.6.1.4.1.5504.2.5.46.1.4.1.5

wlStaticWdsMACAddrTable

table

.1.3.6.1.4.1.5504.2.5.46.1.5 · 1 row entry · 2 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlStaticWdsMACAddrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlStaticWdsMACAddrTable'

Table of statically configured Remote MAC Addresses which are permitted
to bridge to the wireless LAN interfaces when the Bridge restriction mode 
is enabled.

wlStaticWdsMACAddrEntry row .1.3.6.1.4.1.5504.2.5.46.1.5.1

Table of statically configured Remote MAC Addresses which are permitted
to bridge to the wireless LAN interfaces when the Bridge restriction mode
is enabled.

Indexes

Column	Syntax	OID
wlStaticWdsMACIndex The index into the static WDS Remote MAC Address table for a wireless LAN interface.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.5504.2.5.46.1.5.1.1`
wlStaticWdsRemoteMACAddr The MAC address that is permitted WDS bridge access to the wireless LAN interface.	SNMPv2-TCMacAddressr/w Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.5504.2.5.46.1.5.1.2`

wlScanWdsMACAddrTable

table

.1.3.6.1.4.1.5504.2.5.46.1.6 · 1 row entry · 2 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlScanWdsMACAddrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlScanWdsMACAddrTable'

Table of scanned Remote MAC Addresses which are permitted to 
bridge to the wireless LAN interfaces when the Bridge restriction
mode is enabled.

wlScanWdsMACAddrEntry row .1.3.6.1.4.1.5504.2.5.46.1.6.1

Table of scanned Remote MAC Addresses which are permitted to
bridge to the wireless LAN interfaces when the Bridge restriction
mode is enabled.

Indexes

wlBaseCfgIndex wlScanWdsMACIndex

Column	Syntax	OID
wlScanWdsMACIndex The index into the WDS scanned table of Remote MAC Addresses that may access a wireless LAN interface.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.5504.2.5.46.1.6.1.1`
wlScanWdsRemoteMACAddr The MAC address previously scanned that is permitted WDS bridge access to the wireless LAN interface.	SNMPv2-TCMacAddress Type Constraints: `range: 6` Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	`.1.3.6.1.4.1.5504.2.5.46.1.6.1.2`

wlAuthStationsTable

table

.1.3.6.1.4.1.5504.2.5.46.1.7 · 1 row entry · 6 columns

Open in standard view

Uses the zhone variant from /opt/observium/mibs/zhone.

Command help

Walk wlAuthStationsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ZHNWIRELESS' -M '/opt/observium/mibs/zhone:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ZHNWIRELESS::wlAuthStationsTable'

Table of authenicated wireless stations and their status information.

wlAuthStationsEntry row .1.3.6.1.4.1.5504.2.5.46.1.7.1

Table of authenicated wireless stations and their status information.

Indexes

wlAuthStationIndex

Column Syntax OID

wlAuthStationIndex

The index into the Authentication Stations table.

wlAuthStationAssociationStatus

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.5504.2.5.46.1.7.1.1

wlAuthStationMACAddr

The MAC address of the authenticated station.

SNMPv2-TCMacAddress

Type Constraints:
range: 6

Description:

.1.3.6.1.4.1.5504.2.5.46.1.7.1.2

True if the station has been associated.

wlAuthStationAuthorizationStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.5504.2.5.46.1.7.1.3

True if the station has been authorized.