TE-LINK-STD-MIB Table View

This table specifies the grouping of component links into
TE links and the grouping of TE links into bundled links.

teLinkEntry row .1.3.6.1.2.1.10.200.1.1.1

An entry in this table exists for each ifEntry with an
ifType of teLink(200), i.e., for every TE link. An ifEntry
in the ifTable must exist before a teLinkEntry is created
with the corresponding ifIndex. If a TE link …

Indexes

IF-MIBifIndex

Column	Syntax	OID
teLinkAddressType The type of Internet address for the TE link.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.10.200.1.1.1.1
teLinkLocalIpAddr The local Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. For IPv4 and IPv6 numbered links, this object represents the local IP a…	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.2.1.10.200.1.1.1.2
teLinkRemoteIpAddr The remote Internet address for numbered links. The type of this address is determined by the value of the teLinkAddressType object. The remote IP address associated with the TE link (IPv4 and IPv6 numbe…	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.2.1.10.200.1.1.1.3
teLinkMetric The traffic engineering metric for the TE link is derived from its component links. All component links within the TE link must have the same traffic engineering metric.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.200.1.1.1.4
teLinkMaximumReservableBandwidth This attribute specifies the maximum reservable bandwidth on the TE link. This is the union of the maximum reservable bandwidth of all the component links within the TE link that can be used to carry live traffic.	bpsTeLinkBandwidth Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.1.1.5
teLinkProtectionType This attribute specifies the link protection type of the TE link. Descriptions of the different protection types can be found in the 'Routing Extensions in Support of Generalized Multi-Protocol Label Switching (GMPLS)'…	Enumerationr/w Enumerated Values: 1 extraTraffic 2 unprotected 3 shared 4 dedicated1For1 5 dedicated1Plus1 6 enhanced	.1.3.6.1.2.1.10.200.1.1.1.6
teLinkWorkingPriority This object represents a priority value such that a new connection with a higher priority, i.e., numerically lower than this value, is guaranteed to be setup on a primary link and not on a secondary link.	TeLinkPriorityr/w Type Constraints: range: 0..7	.1.3.6.1.2.1.10.200.1.1.1.7
teLinkResourceClass This attribute specifies the TE link resource class. The resource class is a 32 bit bitfield. The resource class for a link bundle is derived from the resource class of its TE links. All TE links within…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.200.1.1.1.8
teLinkIncomingIfId For unnumbered links, the incoming interface is set to the outgoing interface identifier chosen by the neighboring LSR for the reverse link corresponding to this TE link. If the link is numbered, the value of this obje…	Integer32r/w Constraints: range: 0-2147483647	.1.3.6.1.2.1.10.200.1.1.1.9
teLinkOutgoingIfId If the link is unnumbered, the outgoing interface identifier is set to the outgoing interface identifier chosen for the TE link by the advertising LSR. If the link is numbered, the value of this object is 0 and the add…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.2.1.10.200.1.1.1.10
teLinkRowStatus This variable is used to create, modify, and/or delete a row in this table. None of the writable objects in a row can be changed if status is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.1.1.11
teLinkStorageType The storage type for this conceptual row in the teLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.1.1.12

This table specifies the interface switching capability
descriptors associated with the TE links.

teLinkDescriptorEntry row .1.3.6.1.2.1.10.200.1.2.1

An entry in this table is created for every TE link interface
switching capability descriptor. An ifEntry in the ifTable
must exist before a teLinkDescriptorEntry using the same
ifIndex is created. ifType of ifEntry m…

Indexes

IF-MIBifIndex teLinkDescriptorId

Column	Syntax	OID
teLinkDescriptorId This object specifies the link descriptor identifier.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.2.1.10.200.1.2.1.1
teLinkDescrSwitchingCapability This attribute specifies interface switching capability of the TE link, which is derived from its component links.	TeLinkSwitchingCapabilityr/w Type Values: 1 packetSwitch1 2 packetSwitch2 3 packetSwitch3 4 packetSwitch4 51 layer2Switch 100 tdm 150 lambdaSwitch 200 fiberSwitch	.1.3.6.1.2.1.10.200.1.2.1.2
teLinkDescrEncodingType This attribute specifies the TE link encoding type.	TeLinkEncodingTyper/w Type Values: 1 packet 2 ethernet 3 ansiEtsiPdh 5 sdhItuSonetAnsi 7 digitalWrapper 8 lambda 9 fiber 11 fiberChannel	.1.3.6.1.2.1.10.200.1.2.1.3
teLinkDescrMinLspBandwidth This attribute specifies the minimum LSP bandwidth on the TE link. This is derived from the union of the minimum LSP bandwidth of all the component links associated with the TE link that can be used to carry live traff…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.4
teLinkDescrMaxLspBandwidthPrio0 This attribute specifies the maximum LSP bandwidth at priority 0 on the TE link. This is the union of the maximum LSP bandwidth at priority 0 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.5
teLinkDescrMaxLspBandwidthPrio1 This attribute specifies the maximum LSP bandwidth at priority 1 on the TE link. This is the union of the maximum LSP bandwidth at priority 1 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.6
teLinkDescrMaxLspBandwidthPrio2 This attribute specifies the maximum LSP bandwidth at priority 2 on the TE link. This is the union of the maximum LSP bandwidth at priority 2 of all the component links within the TE link that can be use…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.7
teLinkDescrMaxLspBandwidthPrio3 This attribute specifies the maximum LSP bandwidth at priority 3 on the TE link. This is the union of the maximum LSP bandwidth at priority 3 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.8
teLinkDescrMaxLspBandwidthPrio4 This attribute specifies the maximum LSP bandwidth at priority 4 on the TE link. This is the union of the maximum LSP bandwidth at priority 4 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.9
teLinkDescrMaxLspBandwidthPrio5 This attribute specifies the maximum LSP bandwidth at priority 5 on the TE link. This is the union of the maximum LSP bandwidth at priority 5 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.10
teLinkDescrMaxLspBandwidthPrio6 This attribute specifies the maximum LSP bandwidth at priority 6 on the TE link. This is the union of the maximum LSP bandwidth at priority 6 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.11
teLinkDescrMaxLspBandwidthPrio7 This attribute specifies the maximum LSP bandwidth at priority 7 on the TE link. This is the union of the maximum LSP bandwidth at priority 7 of all the component links within the TE link that can be used to carry live…	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.2.1.12
teLinkDescrInterfaceMtu This attribute specifies the interface MTU for the TE link descriptor.	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.10.200.1.2.1.13
teLinkDescrIndication This attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.	TeLinkSonetSdhIndicationr/w Type Values: 0 standard 1 arbitrary	.1.3.6.1.2.1.10.200.1.2.1.14
teLinkDescrRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be changed if teLinkDescrRowStatus is in the active(1) state.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.2.1.15
teLinkDescrStorageType The storage type for this conceptual row in the teLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.2.1.16

This table specifies the SRLGs associated with TE links.

teLinkSrlgEntry row .1.3.6.1.2.1.10.200.1.3.1

An entry in this table contains information about an
SRLG associated with a TE link.
An ifEntry in the ifTable must exist before a
teLinkSrlgEntry using the same ifIndex is created.
The ifType of ifEntry must be teLink(…

Indexes

IF-MIBifIndex teLinkSrlg

Column	Syntax	OID
teLinkSrlg This identifies an SRLG supported by the TE link. An SRLG is identified with a 32-bit number that is unique within an IGP domain. Zero is a valid SRLG number.	Unsigned32 Constraints: range: 0-4294967295	.1.3.6.1.2.1.10.200.1.3.1.1
teLinkSrlgRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified if teLinkSrlgRowStatus is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.3.1.2
teLinkSrlgStorageType The storage type for this conceptual row in the teLinkSrlgTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.3.1.3

This table specifies the priority-based bandwidth table
for TE links.

teLinkBandwidthEntry row .1.3.6.1.2.1.10.200.1.4.1

An entry in this table contains information about
the priority-based bandwidth of TE links. An ifEntry in the
ifTable must exist before a teLinkBandwidthEntry using the
same ifIndex is created. The ifType of ifEntry m…

Indexes

IF-MIBifIndex teLinkBandwidthPriority

Column	Syntax	OID
teLinkBandwidthPriority This attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.	TeLinkPriority Type Constraints: range: 0..7	.1.3.6.1.2.1.10.200.1.4.1.1
teLinkBandwidthUnreserved This attribute specifies the TE link unreserved bandwidth at priority p. It is the sum of the unreserved bandwidths at priority p of all component links associated with the TE link (excluding all links that are strictl…	bpsTeLinkBandwidth Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.4.1.2
teLinkBandwidthRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when teLinkBandwidthRowStatus is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.4.1.3
teLinkBandwidthStorageType The storage type for this conceptual row in the teLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.4.1.4

This table specifies the component link parameters.

componentLinkEntry row .1.3.6.1.2.1.10.200.1.5.1

An entry in this table exists for each ifEntry that
represents a component link. An ifEntry must exist in
the ifTable before a componentLinkEntry is created with
the corresponding ifIndex. ifEntry's ifType can be
of a…

Indexes

IF-MIBifIndex

Column	Syntax	OID
componentLinkMaxResBandwidth This attribute specifies the maximum reservable bandwidth on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.5.1.1
componentLinkPreferredProtection This attribute specifies whether this component link is a primary or secondary entity.	TeLinkProtectionr/w Type Values: 1 primary 2 secondary	.1.3.6.1.2.1.10.200.1.5.1.2
componentLinkCurrentProtection This attribute specifies whether this component link is currently used as primary or secondary link.	TeLinkProtection Type Values: 1 primary 2 secondary	.1.3.6.1.2.1.10.200.1.5.1.3
componentLinkRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkRowStatus is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.5.1.4
componentLinkStorageType The storage type for this conceptual row in the componentLinkTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.5.1.5

This table specifies the interface switching capability
descriptors associated with the component links.

componentLinkDescriptorEntry row .1.3.6.1.2.1.10.200.1.6.1

An entry in this table is created for every component link
descriptor. An ifEntry in the ifTable must exist before a
componentLinkDescriptorEntry using the same ifIndex is
created. ifEntry's ifType can be of any inter…

Indexes

IF-MIBifIndex componentLinkDescrId

Column	Syntax	OID
componentLinkDescrId This object specifies the link descriptor identifier.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.2.1.10.200.1.6.1.1
componentLinkDescrSwitchingCapability This attribute specifies link multiplexing capabilities of the component link.	TeLinkSwitchingCapabilityr/w Type Values: 1 packetSwitch1 2 packetSwitch2 3 packetSwitch3 4 packetSwitch4 51 layer2Switch 100 tdm 150 lambdaSwitch 200 fiberSwitch	.1.3.6.1.2.1.10.200.1.6.1.2
componentLinkDescrEncodingType This attribute specifies the component link encoding type.	TeLinkEncodingTyper/w Type Values: 1 packet 2 ethernet 3 ansiEtsiPdh 5 sdhItuSonetAnsi 7 digitalWrapper 8 lambda 9 fiber 11 fiberChannel	.1.3.6.1.2.1.10.200.1.6.1.3
componentLinkDescrMinLspBandwidth This attribute specifies the minimum LSP bandwidth on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.4
componentLinkDescrMaxLspBandwidthPrio0 This attribute specifies the maximum LSP bandwidth at priority 0 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.5
componentLinkDescrMaxLspBandwidthPrio1 This attribute specifies the maximum LSP bandwidth at priority 1 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.6
componentLinkDescrMaxLspBandwidthPrio2 This attribute specifies the maximum LSP bandwidth at priority 2 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.7
componentLinkDescrMaxLspBandwidthPrio3 This attribute specifies the maximum LSP bandwidth at priority 3 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.8
componentLinkDescrMaxLspBandwidthPrio4 This attribute specifies the maximum LSP bandwidth at priority 4 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.9
componentLinkDescrMaxLspBandwidthPrio5 This attribute specifies the maximum LSP bandwidth at priority 5 on the component link.	thousand bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.10
componentLinkDescrMaxLspBandwidthPrio6 This attribute specifies the maximum LSP bandwidth at priority 6 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.11
componentLinkDescrMaxLspBandwidthPrio7 This attribute specifies the maximum LSP bandwidth at priority 7 on the component link.	bpsTeLinkBandwidthr/w Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.6.1.12
componentLinkDescrInterfaceMtu This attribute specifies the interface MTU for the component link descriptor.	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.10.200.1.6.1.13
componentLinkDescrIndication This attribute specifies whether this interface supports Standard or Arbitrary SONET/SDH.	TeLinkSonetSdhIndicationr/w Type Values: 0 standard 1 arbitrary	.1.3.6.1.2.1.10.200.1.6.1.14
componentLinkDescrRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkDescrRowStatus is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.6.1.15
componentLinkDescrStorageType The storage type for this conceptual row in the componentLinkDescriptorTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.6.1.16

This table specifies the priority-based bandwidth
for component links.

componentLinkBandwidthEntry row .1.3.6.1.2.1.10.200.1.7.1

An entry in this table contains information about
the priority-based bandwidth on component links.
An ifEntry in the ifTable must exist before a
componentLinkBandwidthEntry using the same ifIndex is
created. ifEntry's …

Indexes

IF-MIBifIndex componentLinkBandwidthPriority

Column	Syntax	OID
componentLinkBandwidthPriority This attribute specifies the priority. A value of 0 is valid as specified in the 'Traffic Engineering (TE) Extensions to OSPF Version 2' document.	TeLinkPriority Type Constraints: range: 0..7	.1.3.6.1.2.1.10.200.1.7.1.1
componentLinkBandwidthUnreserved This attribute specifies the component link unreserved bandwidth at priority p.	bpsTeLinkBandwidth Type Constraints: range: 4	.1.3.6.1.2.1.10.200.1.7.1.2
componentLinkBandwidthRowStatus This variable is used to create, modify, and/or delete a row in this table. No read-create object can be modified when componentLinkBandwidthRowStatus is active(1).	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.200.1.7.1.3
componentLinkBandwidthStorageType The storage type for this conceptual row in the componentLinkBandwidthTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.200.1.7.1.4