SWITCH-IGMPSNOOP-MIB Table View

This table, which provides IGMP Snooping information, augments
the 'dot1qStaticMulticastTable' in the Q-MIB (RFC2674).

rcIgmpSnoopEntry row .1.3.6.1.4.1.8886.6.1.11.7.1

Displays by VLAN, Multicast Group, and Multicast receive port
the set of ports enabled to forward Multicast Group traffic as
determined by the IGMP Snooping task.

Indexes

Q-BRIDGE-MIBdot1qVlanIndex Q-BRIDGE-MIBdot1qStaticMulticastAddress Q-BRIDGE-MIBdot1qStaticMulticastReceivePort

Column	Syntax	OID
rcIgmpSnoopEgressPorts This read-only object displays the set of ports enabled to forward specific Multicast Group traffic as determined by the IGMP Snooping task. It should be noted that the IGMP Snooping task generates a pseu…	SWITCH-TCPortList Type Constraints: range: 32	.1.3.6.1.4.1.8886.6.1.11.7.1.1

This table, which provides IGMP Snooping information, 
whitch is multicast router port.

rcIgmpSnoopMrouterEntry row .1.3.6.1.4.1.8886.6.1.11.8.1

Displays by VLAN and Multicast router port.

Indexes

rcIgmpSnoopMrouterVlan rcIgmpSnoopMrouterPort

Column	Syntax	OID
rcIgmpSnoopMrouterVlan the multicast router vlan.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.8886.6.1.11.8.1.1
rcIgmpSnoopMrouterPort the multicast router port .	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.8886.6.1.11.8.1.2
rcIgmpSnoopMrouterStatus the status of multicast router.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.8886.6.1.11.8.1.3

A table containing filtering information for Multicast
and Broadcast IP addresses for each VLAN, configured
into the device by (local or network) management
specifying the set of ports to which frames received
from specific ports and containing specific Multicast
and Broadcast destination addresses are allowed to be
forwarded.  A value of zero in this table as the port
number from which frames with a specific destination
address are received, is used to specify all ports for
which there is no specific entry in this table for that
particular destination address.  Entries are valid for
Multicast and Broadcast addresses only.

rcIgmpSnoopStaticMulticastEntry row .1.3.6.1.4.1.8886.6.1.11.9.1

Filtering information configured into the device by
(local or network) management specifying the set of
ports to which frames received from this specific port
for this VLAN and containing this Multicast or Broadcast
des…

Indexes

Q-BRIDGE-MIBdot1qVlanIndex rcIgmpSnoopStaticMulticastAddress

Column	Syntax	OID
rcIgmpSnoopStaticMulticastAddress The destination IP address in a frame to which this entry's filtering information applies. This object must take the value of a Multicast or Broadcast address.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.8886.6.1.11.9.1.1
rcIgmpSnoopStaticMulticastStaticEgressPorts The set of ports to which frames received from a specific port and destined for a specific Multicast or Broadcast IP address must be forwarded, regardless of any dynamic information e.g. from GMRP. The default value o…	SWITCH-TCPortListr/w Type Constraints: range: 32	.1.3.6.1.4.1.8886.6.1.11.9.1.2
rcIgmpSnoopStaticMulticastStatus This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so differ from the following values. invalid(2) - writing this value to the…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 permanent 4 deleteOnReset 5 deleteOnTimeout	.1.3.6.1.4.1.8886.6.1.11.9.1.3