SUPERMICRO-MPLS-FRR-MIB Table View

This table shows detour LSP or bypass tunnel setup
constraints.

fsMplsFrrConstEntry row .1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1

An entry in this table represents detour LSP or bypass
tunnel setup constraints for a tunnel instance to be
protected by detour LSPs or a bypass tunnel.

Agents must only allow entries in this table to be
cr…

Indexes

MPLS-TE-STD-MIBmplsTunnelIndex MPLS-TE-STD-MIBmplsTunnelInstance MPLS-TE-STD-MIBmplsTunnelIngressLSRId MPLS-TE-STD-MIBmplsTunnelEgressLSRId

Column	Syntax	OID
fsMplsFrrConstIfIndex Uniquely identifies an interface which a fast reroute protection tunnel is configured to potentially protect in the event of a fault. Entries with this index set to 0 indicates that the protection tunnel configured prot…	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.1
fsMplsFrrConstProtectionMethod Indicates which protection method is to be used for fast reroute on this device. Some devices may require a reboot if this variable is to take affect after being modified.	Enumerationr/w Enumerated Values: 1 oneToOneBackup 2 facilityBackup	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.2
fsMplsFrrConstProtectionType Indicates type of the resource protection: linkProtection(1) indicates that this tunnel is setup to protect a particular link's resources. nodeProtection(2) indicates that this tunnel is …	Enumerationr/w Enumerated Values: 1 linkProtection 2 nodeProtection	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.3
fsMplsFrrConstSetupPrio Indicates the setup priority of the detour LSP or bypass tunnel.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.4
fsMplsFrrConstHoldingPrio Indicates the holding priority for detour LSP or bypass tunnel.	Unsigned32r/w Constraints: range: 0-7	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.5
fsMplsFrrConstSEStyle Indicates the SE style desired. This will be TRUE when facility backup method is desired. One to One backup method can be made sender template specific by setting this style TRUE.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.6
fsMplsFrrConstInclAnyAffinity Indicates the include-any link constraint for the detour LSP or bypass tunnel. A link satisfies the include-any constraint if and only if the constraint is zero, or the link and the constraint have a resource class in c…	MPLS-TC-STD-MIBMplsTunnelAffinityr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.7
fsMplsFrrConstInclAllAffinity Indicates the include-all link constraint for the detour LSP or bypass tunnel. A link satisfies the include-all constraint if and only if the link contains all of the administrative groups specified in the constraint.	MPLS-TC-STD-MIBMplsTunnelAffinityr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.8
fsMplsFrrConstExclAnyAffinity Indicates the exclude-any link constraint for the detour LSP or bypass tunnel. A link satisfies the exclude-any constraint if and only if the link contains none of the administrative groups specified in the constraint.	MPLS-TC-STD-MIBMplsTunnelAffinityr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.9
fsMplsFrrConstHopLimit The maximum number of hops that the detour LSP or bypass tunnel may traverse.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.10
fsMplsFrrConstBandwidth The maximum bandwidth specifically reserved for detour LSP or bypass tunnel, in units of thousands of bits per second (Kbps). Note that setting this value to 0 indicates best-effort treatment.	kilobits per secondMPLS-TC-STD-MIBMplsBitRater/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.11
fsMplsFrrConstRowStatus This variable is used to create, modify, and/or delete a row in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.13.3.2.1.1.1.12

This table is an extension to mplsTunnelTable. This Table
performs the association of tunnels to an interface, 
association of Protected Tunnel with that of backup tunnel,
and shows the status of the backup tunnels.

fsMplsTunnelExtEntry row .1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1

An entry in this table represents an extension to
mplsTunnelTable.

Indexes

No indexes recorded

Column	Syntax	OID
fsMplsTunnelExtProtIfIndex Uniquely identifies an interface which a fast reroute protection tunnel is configured to potentially protect in the event of a fault.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.1
fsMplsTunnelExtProtectionType Indicates type of the resource protection: none(0) indicates default value this will be used when tunnel is not supporting facility backups. linkProtection(1) indicates that this tunnel i…	Enumeration Enumerated Values: 0 none 1 linkProtection 2 nodeProtection	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.2
fsMplsTunnelExtBkpTunIdx Denotes Backup Tunnel Index for the Tunnel in mplsTunnelTable.	MPLS-TC-STD-MIBMplsTunnelIndex Type Constraints: range: 0..65535	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.3
fsMplsTunnelExtBkpInst Denotes Backup Tunnel Instance for the Tunnel in mplsTunnelTable. - lower 16 bits : protected tunnel instance - higher 16 bits: detour instance	MPLS-TC-STD-MIBMplsTunnelInstanceIndex Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.4
fsMplsTunnelExtBkpIngrLSRId Denotes Backup Tunnel Ingress LSR ID for the Tunnel in mplsTunnelTable.	MPLS-TC-STD-MIBMplsExtendedTunnelId Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.5
fsMplsTunnelExtBkpEgrLSRId Denotes Backup Tunnel Egress LSR ID for the Tunnel in mplsTunnelTable.	MPLS-TC-STD-MIBMplsExtendedTunnelId Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.6
fsMplsTunnelExtOne2OnePlrId This value represents the PLR that has initiated a detour LSP to protect a tunnel instance. This value is signalled via the DETOUR object defined in MPLS RSVP protocol as described in RFC-4090.	MPLS-TC-STD-MIBMplsLsrIdentifier Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.7
fsMplsTunnelExtOne2OnePlrSenderAddrType Denotes the address type of this detour instance's sender address.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.8
fsMplsTunnelExtOne2OnePlrSenderAddr The IP address of the PLR which has initiated the detour LSP. The type of this address is determined by the value of the fsMplsTunnelExtOne2OnePlrSenderAddrType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.9
fsMplsTunnelExtOne2OnePlrAvoidNAddrType Denotes the address type of the node that this PLR tries to avoid.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.10
fsMplsTunnelExtOne2OnePlrAvoidNAddr The IP address of the node that this PLR tries to avoid. The type of this address is determined by the value of the fsMplsTunnelExtOne2OnePlrAvoidNAddrType object. This value is signalled via the DETOUR object defined i…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.11
fsMplsTunnelExtDetourActive Indicates whether or not the main LSP has switched over to this detour LSP. This is only relevant for detours originated by this node.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.12
fsMplsTunnelExtDetourMerging This value represents whether or not this detour is merged. This value MUST be set to none(1) if this detour is not merged. This value MUST be set to protectedTunnel(2) if this detour is merged with the p…	Enumeration Enumerated Values: 1 none 2 protectedTunnel 3 detour	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.13
fsMplsTunnelExtFacRouteDBProtTunStatus Specifies the state of the protected tunnel. active This tunnel's label has been placed in the LFIB and is ready to be applied to incoming packets. ready - This tunnel's…	Enumeration Enumerated Values: 1 active 2 ready 3 partial	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.14
fsMplsTunnelExtFacRouteDBProtTunResvBw Specifies the amount of bandwidth in units of '1,000 bits per second', actually reserved by the protection tunnel for facility backup purposes. This value is repeated here from the MPLS-TE-STD-MIB MIB module because the…	kilobits per secondMPLS-TC-STD-MIBMplsBitRate Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.15
fsMplsTunnelExtProtectionMethod Indicates type of the protection method in use: oneToOneBackup(1) indicates OneToOne Backup method is used. facilityBackup(2) indicates facility backup method is used.	Enumeration Enumerated Values: 1 oneToOneBackup 2 facilityBackup	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.16
fsMplsTunnelExtMaxGblRevertTime The Maximum Time after which the re-optimization of LSP begins for the FRR Protected LSP in case of link/node failure detection. It is specified in milli seconds.	SNMPv2-TCTimeIntervalr/w Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.10876.101.1.13.3.2.1.2.1.17

This table associates the tunnel to an interface to be 
used as a Backup Tunnel for a protected tunnelin case of 
facility backup method. This Table is applicable only in
case of Fast ReRoute Support.

fsMplsBypassTunnelIfEntry row .1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1

An entry in this table represents the association of
the tunnel to an interface to be used as a backup tunnel for
fast reroute supported tunnel in case of facility backup method.
The Bypass Tunnel associate…

Indexes

fsMplsBypassTunnelIfIndex fsMplsBypassTunnelIndex fsMplsBypassTunnelInstance fsMplsBypassTunnelIngressLSRId fsMplsBypassTunnelEgressLSRId

Column	Syntax	OID
fsMplsBypassTunnelIfIndex Uniquely identifies an interface to which a Bypass Tunnel is associated to protect a Fast ReRoute Supported Tunnel in the event of a fault. It is the primary index to this table.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.1
fsMplsBypassTunnelIndex Uniquely identifies the Tunnel index of the Bypass Tunnel used to protect a Fast ReRoute Supported Tunnel in the even of fault. It is a secondary index to this table. This Object should have an entry in mplsTunnelEntr…	MPLS-TC-STD-MIBMplsTunnelIndex Type Constraints: range: 0..65535	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.2
fsMplsBypassTunnelInstance Uniquely identifies the Tunnel Instance of the Bypass Tunnel used to protect a Fast ReRoute Supported Tunnel in the even of fault. It is a secondary index to this table. This Object should have an entry in mplsTunnelE…	MPLS-TC-STD-MIBMplsTunnelInstanceIndex Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.3
fsMplsBypassTunnelIngressLSRId Uniquely identifies the Tunnel Ingress LSR ID of the Bypass Tunnel used to protect a Fast ReRoute Supported Tunnel in the even of fault. It is a secondary index to this table. This Object should have an entry in mplsT…	MPLS-TC-STD-MIBMplsExtendedTunnelId Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.4
fsMplsBypassTunnelEgressLSRId Uniquely identifies the Tunnel Egress LSR ID of the Bypass Tunnel used to protect a Fast ReRoute Supported Tunnel in the even of fault. It is a secondary index to this table. This Object should have an entry in mplsTu…	MPLS-TC-STD-MIBMplsExtendedTunnelId Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.5
fsMplsBypassTunnelRowStatus This variable is used to create and delete a row in this table. The Only Operations supported in this table are Create and Go and Destroy.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.13.3.2.1.3.1.6

This table sparsely extends mplsTunnelARHopTable defined
in the MPLS-TE-STD-MIB MIB module with fast-reroute objects.
These objects specify the status of local protection including
availability and active use, on a per-hop basis, of hops
traversed by a protected tunnel.  Note that object
availability in this table is governed by the support of
the Record Route Object in the RSVP-TE signaling of the
implementation.

fsMplsFrrTunARHopEntry row .1.3.6.1.4.1.10876.101.1.13.3.2.1.4.1

This entry contains fast-reroute protection status of a single
protected tunnel hop.

Indexes

MPLS-TE-STD-MIBmplsTunnelARHopListIndex MPLS-TE-STD-MIBmplsTunnelARHopIndex

Column	Syntax	OID
fsMplsFrrTunARHopProtectType This object indicates the protection type or types of the associated path hop object. Note that since this object is a BITS type, one, none or all of the bits may be set to indicate various combinations of protection t…	Bits Enumerated Values: 0 path 1 node 2 link	.1.3.6.1.4.1.10876.101.1.13.3.2.1.4.1.1
fsMplsFrrTunARHopProtectTypeInUse This object indicates the protection type or types that are currently in use by the associated path hop object. Note that since this object is a BITS type, one, none or all of the bits may be set to indicate various com…	Bits Enumerated Values: 0 path 1 node 2 link	.1.3.6.1.4.1.10876.101.1.13.3.2.1.4.1.2
fsMplsFrrTunARHopLabel This label indicates the downstream node label used incase of fast reroute facility backup method is desired by the LSP	MPLS-TC-STD-MIBMplsLabel Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.13.3.2.1.4.1.3
fsMplsFrrTunARBwProtAvailable This Object indicates whether bandwidth protection is available on this node.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.13.3.2.1.4.1.4