SUPERMICRO-IPV6-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
15
Rows
15
Columns
164

fsipv6IfTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.1 · 1 row entry · 23 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6IfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6IfTable' 
The IPv6 Interface table contains information on the 
entity's internetwork-layer interfaces on which IPv6.
protocol is enabled. An IPv6 interface constitutes a logical 
network layer attachment to the layer immediately below
IPv6. These include LAN interfaces, Point-to-Point interfaces, 
NBMA interfaces and IPv6 over IPv4 Tunnel interfaces.
fsipv6IfEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.1.1
An interface entry containing objects about a particular
IPv6 interface. The entry is created or deleted from SNMP.
Indexes
Column Syntax OID
fsipv6IfIndex
A unique value identifying the particular IPv6
interface.
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.1
fsipv6IfType
The type of interface immediately `below' the network layer
in the protocol stack.
Enumeration
Enumerated Values:
6ethernetcsmacd
23ppp
32framerelay
131tunnel
136l3ipvlan
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.2
fsipv6IfPortNum
This object identifies the 'interface' over which this
network interface operates and is dependent on the value of
fsipv6IfType. This object reflects the ifindex value of
ifTable.
Integer32
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.3
fsipv6IfCircuitNum
This object identifies the circuit over which this network
interface operates and is dependent on the value of
fsipv6IfType. If the data-link layer is Ethernet, PPP or
IPv4 Tunnel, this object can have only value of zer…
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.4
fsipv6IfToken
The address token for this interface that is (at least)
unique on the link this interface is attached to. This token
can be specified only if the fsipv6IfType is frame-relay(32). For
other interface types, the interfac…
OctetStringr/w
Constraints:
range: 1-8
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.5
fsipv6IfAdminStatus
Indicates whether IPv6 is enabled/disabled on this interface.
When lower layer indicates the creation of the interface, an
entry will be create in IPv6 interfac table with
fsipv6IfAdminStatus in down(2) state. Either on…
Enumerationr/w
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.6
fsipv6IfOperStatus
The operational state of interface. It is up(1) if the
fsipv6IfAdminStatus is 'up' and the layer below the network
layer is also operational. Otherwise it is down(2).
Enumeration
Enumerated Values:
1up
2down
3stale
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.7
fsipv6IfRouterAdvStatus
The router advertisement status on this interface. When
the object is set to enabled(1), router advertisements can be
allowed on the IPv6 interface. Otherwise, router advertisements
are not allowed.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.8
fsipv6IfRouterAdvFlags
This object specifies the bits to be set in the router
advertisements sent by this entity on this interface.
M-bit set in the router advertisement indicates hosts
to configure an address by stateful protocol means. O-bi…
Enumerationr/w
Enumerated Values:
1mbit
2obit
3nombit
4noobit
5mobits
6none
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.9
fsipv6IfHopLimit
The Hop Limit value to be placed in the router advertisements
sent on this IPv6 interface.
Integer32r/w
Constraints:
range: 1-255
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.10
fsipv6IfDefRouterTime
The default router time to be indicated in the router
advertisements sent on this IPv6 interface. This defines the
time in seconds for which this entity acts as the default
router for all all hosts on the interface. A …
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.11
fsipv6IfReachableTime
The reachable time to be indicated in the router
advertisements sent on this IPv6 interface and also used by
this entity. This defines the time in seconds that a neighboring
node is considered to be reachable after havi…
Integer32r/w
Constraints:
range: 0-3600
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.12
fsipv6IfRetransmitTime
The retransmit time to be indicated in the router
advertisements sent on this IPv6 interface and also used by
this entity. This defines the time in seconds between
retransmitted Neighbor Solicitations and is used duri…
Integer32r/w
Constraints:
range: 1-3600
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.13
fsipv6IfDelayProbeTime
The time in seconds to delay before starting unreachability
probing of neighbor entries which are stale.
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.14
fsipv6IfPrefixAdvStatus
The prefix advertisement status on this IPv6 interface.
Object value enabled(1) allows the configured prefixes to
be advertised in router advertisements. Otherwise, the prefixes
are not sent in router advertisements.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.15
fsipv6IfMinRouterAdvTime
The minimum time in seconds allowed between sending
unsolicited router advertisements.The default value is
one-third the default value of fsipv6IfMaxRouterAdvTime.
The value can be configured in the range between 3 sec…
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.16
fsipv6IfMaxRouterAdvTime
The maximum time in seconds between sending unsolicited
router advertisements. Router advertisements are sent
periodically at a random interval between the values
specified by fsipv6IfMinRouterAdvTime and
fsipv6IfMaxRo…
Integer32r/w
Constraints:
range: 4-1800
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.17
fsipv6IfDADRetries
The maximum number of neighbor solicitations sent for
the purpose of duplicate address detection on a tentative
address.
Integer32r/w
Constraints:
range: 0-10
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.18
fsipv6IfForwarding
This MIB object is used to configure IPv6 routing and forwarding
on this interface. The default value is set to enabled.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.19
fsipv6IfRoutingStatus
This MIB object indicates the current routing status
on this interface. This is based on the global IPv6
forwarding status of the mib object 'ipv6Forwarding'.
If 'ipv6Forwarding' is set to disabled, the routing
status i…
Enumeration
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.20
fsipv6IfIcmpErrInterval
Time interval between tokens being added to the ICMPv6 token bucket.
millisecondsInteger32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.21
fsipv6IfIcmpTokenBucketSize
Maximum number of tokens stored in the ICMPv6 bucket
Integer32r/w
Constraints:
range: 0-200
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.22
fsipv6IfDestUnreachableMsg
Indicates whether ICMPv6 destination unreachable messages are
enabled/disabled on this interface.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.10876.101.1.28.1.2.1.1.23

fsipv6IfStatsTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.2 · 1 row entry · 34 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6IfStatsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6IfStatsTable' 
IPv6 interface traffic statistics
fsipv6IfStatsEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.2.1
An interface statistics entry containing objects
at a particular IPv6 interface.
Indexes
Column Syntax OID
fsipv6IfStatsIndex
The index value which uniquely identifies the IPv6
interface for which this statistics are maintained.
The interface identified by a particular value of this
index is the same interface as identified by the same
value…
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.1
fsipv6IfStatsInReceives
The total number of input datagrams received from
interfaces, including those received in error.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.2
fsipv6IfStatsInHdrErrors
The number of input datagrams discarded due to
errors in their IPv6 headers, including version
number mismatch, other format errors, hop count
exceeded, errors discovered in processing their
IPv6 options, etc.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.3
fsipv6IfStatsTooBigErrors
The number of datagrams that could not be forwarded
because their size exceeded the Path MTU
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.4
fsipv6IfStatsInAddrErrors
The number of input datagrams discarded because
the IPv6 address in their IPv6 header's destination
field was not a valid address to be received at
this entity. This count includes invalid
addresses (e.g., ::0) and uns…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.5
fsipv6IfStatsForwDatagrams
The number of input datagrams for which this
entity was not their final IPv6 destination, as a
result of which an attempt was made to find a
route to forward them to that final destination.
In entities which do not act …
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.6
fsipv6IfStatsInUnknownProtos
The number of locally-addressed datagrams
received successfully but discarded because of an
unknown or unsupported protocol.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.7
fsipv6IfStatsInDiscards
The number of input IPv6 datagrams for which no
problems were encountered to prevent their
continued processing, but which were discarded
(e.g., for lack of buffer space). Note that this
counter does not include any da…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.8
fsipv6IfStatsInDelivers
The total number of input datagrams successfully
delivered to IPv6 user-protocols (including ICMP).
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.9
fsipv6IfStatsOutRequests
The total number of IPv6 datagrams which local IPv6
user-protocols (including ICMP) supplied to IPv6 in
requests for transmission. Note that this counter
does not include any datagrams counted in
fsipv6IfStatsForwDatag…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.10
fsipv6IfStatsOutDiscards
The number of output IPv6 datagrams for which no
problem was encountered to prevent their
transmission to their destination, but which were
discarded (e.g., for lack of buffer space). Note
that this counter would inclu…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.11
fsipv6IfStatsOutNoRoutes
The number of IPv6 datagrams discarded because no
route could be found to transmit them to their
destination. Note that this counter includes any
packets counted in fsipv6IfStatsForwDatagrams which
meet this `no-route'…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.12
fsipv6IfStatsReasmReqds
The number of IPv6 fragments received which needed
to be reassembled at this entity.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.13
fsipv6IfStatsReasmOKs
The number of IPv6 datagrams successfully
reassembled.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.14
fsipv6IfStatsReasmFails
The number of failures detected by the IPv6 re-
assembly algorithm (for whatever reason: timed
out, errors, etc). Note that this is not
necessarily a count of discarded IPv6 fragments
since some algorithms (notably the…
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.15
fsipv6IfStatsFragOKs
The number of IPv6 datagrams that have been
successfully fragmented at this entity.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.16
fsipv6IfStatsFragFails
The number of IPv6 datagrams that have been
discarded because they needed to be fragmented
at this entity but could not be.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.17
fsipv6IfStatsFragCreates
The number of IPv6 datagram fragments that have
been generated as a result of fragmentation at
this entity.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.18
fsipv6IfStatsInMcastPkts
The number of multicast packets received
by the interface
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.19
fsipv6IfStatsOutMcastPkts
The number of multicast packets transmitted
by the interface
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.20
fsipv6IfStatsInTruncatedPkts
The number of input datagrams discarded because
datagram frame didn't carry enough data
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.21
fsipv6IfStatsInRouterSols
The number of ICMP Router Solicit messages
received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.22
fsipv6IfStatsInRouterAdvs
The number of ICMP Router Advertisement messages
received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.23
fsipv6IfStatsInNeighSols
The number of ICMP Neighbor Solicit messages
received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.24
fsipv6IfStatsInNeighAdvs
The number of ICMP Neighbor Advertisement
messages received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.25
fsipv6IfStatsInRedirects
The number of ICMP Redirect messages
received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.26
fsipv6IfStatsOutRouterSols
The number of ICMP Router Solicit messages
sent.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.27
fsipv6IfStatsOutRouterAdvs
The number of ICMP Router Advertisement messages
sent.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.28
fsipv6IfStatsOutNeighSols
The number of ICMP Neighbor Solicitation
messages sent.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.29
fsipv6IfStatsOutNeighAdvs
The number of ICMP Neighbor Advertisement
messages sent.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.30
fsipv6IfStatsOutRedirects
The number of Redirect messages sent.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.31
fsipv6IfStatsLastRouterAdvTime
The time at which the last Periodic router advertisement
was sent.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.32
fsipv6IfStatsNextRouterAdvTime
The time at which the next Periodic router advertisement
is scheduled to be sent.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.33
fsipv6IfStatsIcmp6ErrRateLmtd
No of rate limited ICMP6 error messages
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.2.1.34

fsipv6PrefixTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.3 · 1 row entry · 6 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6PrefixTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6PrefixTable' 
The table containing entity's IPv6 address prefix information.
fsipv6PrefixEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.3.1
The entry in the IPv6 Address Prefix Table which defines a
prefix to be advertised in the route advertisement message
send on an IPv6 interface.
Indexes
Column Syntax OID
fsipv6PrefixIndex
The index value which uniquely identifies the IPv6
interface on which this IPv6 address prefix entry is
to be advertised. The interface identified by a
particular value of this index is the same interface
as identified …
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.1
fsipv6PrefixAddress
The IPv6 address prefix to which this entry's prefix
information pertains.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.2
fsipv6PrefixAddrLen
The length of the prefix (in bits) associated with
the IPv6 address prefix of this entry.
Integer32
Constraints:
range: 1-128
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.3
fsipv6PrefixProfileIndex
Indicates the index into the IPv6 Address Profile Table.
This entry of the IPv6 Address Profile table defines the
parameters for this prefix.
Integer32r/w
Constraints:
range: 0-200
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.4
fsipv6PrefixAdminStatus
Indicates the administrative status of the prefix.
CreateAndGo and NotInService are not supported.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.5
fsipv6SupportEmbeddedRp
Flag to control the usage of associated IPv6 Prefix address
as a valid embedded-RP prefix on specified interface
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.10876.101.1.28.1.2.3.1.6

fsipv6AddrTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.4 · 1 row entry · 8 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6AddrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6AddrTable' 
The table containing entity's IPv6 addressing information.
fsipv6AddrEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.4.1
The entry in the IPv6 Address Table which defines a
unicast, anycast or link-local address on an IPv6 interface.
Indexes
Column Syntax OID
fsipv6AddrIndex
The index value which uniquely identifies the IPv6
interface on which this IPv6 address entry exists.
The interface identified by a particular value of this
index is the same interface as identified by the same
value …
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.1
fsipv6AddrAddress
The IPv6 address to which this entry's addressing
information pertains.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.2
fsipv6AddrPrefixLen
The length of the prefix (in bits) associated with
the IPv6 address of this entry. For a link-local address,
the prefix is always start with '0xfe80' and the prefix
length is 128 bits.
Integer32
Constraints:
range: 0-128
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.3
fsipv6AddrAdminStatus
Indicates the desired status of the address. Also a creation
of an address can trigger IPv6 to be enabled over the
interface. Similarly deletion of all the address may trigger
IPv6 to be disabled on the interface. NotIn…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.4
fsipv6AddrType
Indicates whether the address is a unicast, anycast or
link-local address. Syntactically there is no difference
between a unicast address and a anycast address while a
link-local address has the prefix '0xfe80'. This
ob…
Enumerationr/w
Enumerated Values:
1unicast
2anycast
3linklocal
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.5
fsipv6AddrProfIndex
Indicates the index into the IPv6 Address Profile Table.
This entry of the IPv6 Address Profile table defines the
parameters for this address. For a link-local address,
this object always takes the value zero and cannot…
Integer32r/w
Constraints:
range: 0-200
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.6
fsipv6AddrOperStatus
Indicates the operational status of the address. A
status of failed(4) indicates that a duplicate address has
been detected on this IPv6 interface. On interfaces on
which Duplicate Address Detection is not performed, th…
Enumeration
Enumerated Values:
1tentative
2complete
3down
4failed
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.7
fsipv6AddrScope
Scope is a 4-bit value that describes the scope of
an IPV6 address.An unicast address can possibly have 2
scopes (Linklocal and Global) only. A multicast address
can have a maximum of 11 scopes.The reserved scopes cann…
INET-ADDRESS-MIBInetScopeType
Type Values:
1interfaceLocal
2linkLocal
3subnetLocal
4adminLocal
5siteLocal
8organizationLocal
14global
 .1.3.6.1.4.1.10876.101.1.28.1.2.4.1.8

fsipv6AddrProfileTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.5 · 1 row entry · 9 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6AddrProfileTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6AddrProfileTable' 
The table containing information for an address or set of
addresses of the entity.
fsipv6AddrProfileEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.5.1
The entry in the IPv6 Address Profile Table which contains
parameters related to the advertisement of address prefixes.
One or more IPv6 addresses refer to this profile through the
object fsipv6AddrProfIndex in the fsip…
Indexes
Column Syntax OID
fsipv6AddrProfileIndex
A unique value identifying the particular IPv6 Address
profile entry. This is referred by fsipv6AddrProfIndex of
IPv6 Address Table. The index 0 is created with default value
during system start-up and this entry is not…
Unsigned32
Constraints:
range: 0-200
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.1
fsipv6AddrProfileStatus
Indicates that the entry is valid or not. An entry other
than the first entry can be deleted by setting this object
to invalid(2).
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.2
fsipv6AddrProfilePrefixAdvStatus
If this object has value on(1), the address prefixes
corresponding to those addresses which use this profile
will be advertised in router advertisements sent by this
entity. If it has value off(2), these address prefixe…
Enumerationr/w
Enumerated Values:
1on
2off
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.3
fsipv6AddrProfileOnLinkAdvStatus
If this object has value on(1), the address prefixes
corresponding to those addresses which use this profile
will be advertised with on-link flag set in the router
advertisements sent by this entity. These prefixes can…
Enumerationr/w
Enumerated Values:
1on
2off
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.4
fsipv6AddrProfileAutoConfAdvStatus
If this object has value on(1), the address prefixes
corresponding to those addresses which use this profile
will be advertised with autonomous address configuration
flag set in the router advertisements sent by this e…
Enumerationr/w
Enumerated Values:
1on
2off
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.5
fsipv6AddrProfilePreferredTime
This object specifies the preferred lifetime in seconds
for the address prefixes corresponding to those addresses
which use this profile. This is sent in router advertisements
by this entity. A value of 4,294,967,295 r…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.6
fsipv6AddrProfileValidTime
This object specifies the valid lifetime in seconds
for the address prefixes corresponding to those addresses
which use this profile. This is sent in router advertisements
by this entity. A value of 4,294,967,295 repre…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.7
fsipv6AddrProfileValidLifeTimeFlag
By setting this flag to fixed (1),the router
advertisement Valid life time value is set
to fixed and by setting to variable(2), the
router advertisement Valid life time value
can decrease in real time. This flag wil…
Enumerationr/w
Enumerated Values:
1fixed
2variable
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.8
fsipv6AddrProfilePreferredLifeTimeFlag
By setting this flag to fixed (1),the router
advertisement Preferred life time value is set
to fixed and by setting to variable(2), the
router advertisement preferred life time value
can decrease in real time. This …
Enumerationr/w
Enumerated Values:
1fixed
2variable
 .1.3.6.1.4.1.10876.101.1.28.1.2.5.1.9

fsipv6PmtuTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.6 · 1 row entry · 4 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6PmtuTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6PmtuTable' 
IPv6 Path MTU table. This table contains
an entry for a specific path traversed by
packets exchanged between the source and
destination nodes.
fsipv6PmtuEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.6.1
A Path MTU entry.
Indexes
Column Syntax OID
fsipv6PmtuDest
The destination IPv6 address of the packets
to be exchanged.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.6.1.1
fsipv6Pmtu
Indicates the path MTU value for the path.
Integer32r/w
Constraints:
range: 1280-65535
 .1.3.6.1.4.1.10876.101.1.28.1.2.6.1.2
fsipv6PmtuTimeStamp
Indicates the entry created time in the PMTU table.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.6.1.3
fsipv6PmtuAdminStatus
The desired status of the PmtuTable. This variable
has to be made valid(1) for creating a entry in the PmtuTable.
If set to invalid(2), the entry is deleted.
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.28.1.2.6.1.4

fsipv6NdLanCacheTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.7 · 1 row entry · 6 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6NdLanCacheTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6NdLanCacheTable' 
The IPv6 Address Translation table used for
mapping from IPv6 addresses to physical addresses
on Ethernet.
fsipv6NdLanCacheEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.7.1
Each entry contains one IPv6 address to `physical'
address equivalence. Entries are created dynamically upon
address resolution or statically from SNMP.
Indexes
Column Syntax OID
fsipv6NdLanCacheIfIndex
The index value which uniquely identifies the IPv6
interface on which this fsipv6NdLanCache entry exists.
The interface identified by a particular value of this
index is the same interface as identified by the same
val…
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.1
fsipv6NdLanCacheIPv6Addr
The IPv6 Address corresponding to the `physical' address
on Ethernet.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.2
fsipv6NdLanCacheStatus
Setting this object to the value invalid(2)
effects in invalidating the corresponding entry
in the fsipv6NdLanCacheTable. Otherwise, the entry
remains valid.
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.3
fsipv6NdLanCachePhysAddr
The `physical' address on Ethernet.
OctetStringr/w
Constraints:
range: 6-6
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.4
fsipv6NdLanCacheState
The reachability state of NdLanCacheEntry. Upon creation of
an entry from SNMP, this object takes the value as 'static'.
Otherwise takes the value that correspond to the states of
dynamically created entries.
Enumeration
Enumerated Values:
1static
2reachable
3incomplete
4stale
5delay
6probe
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.5
fsipv6NdLanCacheUseTime
The value of sysUpTime at the time the entry was consulted
upon IPv6 packet forwarding.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.7.1.6

fsipv6NdWanCacheTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.8 · 1 row entry · 5 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6NdWanCacheTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6NdWanCacheTable' 
The IPv6 Address Translation table used for
mapping from IPv6 addresses to physical addresses
on NBMA interface. The 'physical address' actually refers
to the IPv6 interface on which the Ipv6Address is on-link.
fsipv6NdWanCacheEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.8.1
Each entry contains one IPv6 address to `physical'
address equivalence. Entries are created dynamically upon
reception of IPv6 packet from an on-link source or statically
from SNMP.
Indexes
Column Syntax OID
fsipv6NdWanCacheIfIndex
The index value which uniquely identifies the IPv6
interface on which this fsipv6NdWanCache entry exists.
The interface identified by a particular value of this
index is the same interface as identified by the same
va…
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.8.1.1
fsipv6NdWanCacheIPv6Addr
The IPv6 Address of the on-link node on this NBMA interface.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.8.1.2
fsipv6NdWanCacheStatus
Setting this object to the value 'invalid(2)'
effects in invalidating the corresponding entry
in the fsipv6NdWanCacheTable. Otherwise, the entry
remains valid.
Enumerationr/w
Enumerated Values:
1valid
2invalid
 .1.3.6.1.4.1.10876.101.1.28.1.2.8.1.3
fsipv6NdWanCacheState
The reachability state of NdWanCacheEntry.
Upon creation of an entry from SNMP, this object
takes the value as 'static'. Otherwise takes the
value as 'reachable' that corresponds to the state
of dynamically created …
Enumeration
Enumerated Values:
1static
2reachable
 .1.3.6.1.4.1.10876.101.1.28.1.2.8.1.4
fsipv6NdWanCacheUseTime
The value of sysUpTime at the time the entry
was consulted upon IPv6 packet forwarding.
SNMPv2-SMITimeTicks
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.8.1.5

fsipv6PingTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.12 · 1 row entry · 19 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6PingTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6PingTable' 
This entity's IPv6 Ping Table.
fsipv6PingEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.12.1
Contains the information about a particular IPv6 Ping
operation. An entry is created/deleted from SNMP.
Indexes
Column Syntax OID
fsipv6PingIndex
A unique value identifying the particular IPv6 Ping entry.
Integer32
Constraints:
range: 0-5
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.1
fsipv6PingDest
The IPv6 address of the destination to be pinged. This
should be a unicast or link-local address
OctetStringr/w
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.2
fsipv6PingIfIndex
The index value which uniquely identifies the IPv6
interface on which this Ping is to be sent. The interface
identified by a particular value of this index is the same
interface as identified by the same value of fsip…
IF-MIBInterfaceIndexr/w
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.3
fsipv6PingAdminStatus
The desired status for the ping operation. This variable
has to be made up(1) for starting the ping operation.
If set to down(2), the ping is stopped but the statistics
will still be available. The entry is created whe…
Enumerationr/w
Enumerated Values:
1up
2down
3invalid
4create
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.4
fsipv6PingInterval
The time interval in seconds between successive pings
sent to the destination.
Integer32r/w
Constraints:
range: 1-100
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.5
fsipv6PingRcvTimeout
The time in seconds after which this entity times out
waiting for a particular ping response.
Integer32r/w
Constraints:
range: 0-100
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.6
fsipv6PingTries
The number of times the destination is to be pinged.
Integer32r/w
Constraints:
range: 1-1000
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.7
fsipv6PingSize
The size of the data portion of the Ping packet.
Integer32r/w
Constraints:
range: 32-2080
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.8
fsipv6PingSentCount
Total number of packets sent to destination.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.9
fsipv6PingAverageTime
The average value of the round trip time in seconds to this
destination.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.10
fsipv6PingMaxTime
The maximum value of the round trip time in seconds to this
destination.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.11
fsipv6PingMinTime
The minimum value of the round trip time in seconds to this
destination.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.12
fsipv6PingOperStatus
The current status of this ping operation.
Enumeration
Enumerated Values:
1inprogress
2notinprogress
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.13
fsipv6PingSuccesses
The number of ping responses received.
SNMPv2-SMICounter32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.14
fsipv6PingPercentageLoss
Percentage of lost packets for which no responses were
received till timeout.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.15
fsipv6PingData
Data that should be sent in the Ping message
OctetStringr/w
Constraints:
range: 6-6
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.16
fsipv6PingSrcAddr
Source address to be used for the ping
OctetStringr/w
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.17
fsipv6PingZoneId
Zone-Id shoule be able to identify a particular zone
of the address's scope. This Zone id applies
to all kinds of unicast and multicast addresses of
non-global scope except the unspecified address.
The zo…
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.18
fsipv6PingDestAddrType
The address type of the destination to be pinged.
other - unicast or linklocal address
anycast - anycast address .An IPv6 packet cannot have anycast
address as source address. So fsipv6PingDestAddrType is used
to dist…
Enumerationr/w
Enumerated Values:
0other
2anycast
 .1.3.6.1.4.1.10876.101.1.28.1.2.12.1.19

fsipv6NDProxyListTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.13 · 1 row entry · 2 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6NDProxyListTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6NDProxyListTable' 
Configurable list of IPv6 Addresses for which
Proxy Neighbor Discovery is desired.
fsipv6NDProxyListEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.13.1
An entry in the ND Proxy Table. Each
entry specifies the IPv6 address for
which proxy feature is needed, and
the adminstatus for the row.
Indexes
Column Syntax OID
fsipv6NdProxyAddr
IPv6 address for Proxy ND.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.13.1.1
fsipv6NdProxyAdminStatus
The desired state of the ND Proxy list entry.
When set to create(4) the IPv6 interface is
created and invalid(4) to delete the interface.
Enumerationr/w
Enumerated Values:
1create
2invalid
 .1.3.6.1.4.1.10876.101.1.28.1.2.13.1.2

fsipv6AddrSelPolicyTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.14 · 1 row entry · 12 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6AddrSelPolicyTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6AddrSelPolicyTable' 
This table is used for default address selection in IPv6. This table is used to configure the Precedence
and Label associated with a source/destination address. The Address Selection Policy Table
contains the following default entries -
          
Prefix        Precedence  Label
::1/128               50     0
::/0                  40     1
2002::/16             30     2
::/96                 20     3
::ffff:0:0/96         10     4
          
A lookup of this table aids in selection of best source/destination address from amongst a candidate list.
fsipv6AddrSelPolicyEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.14.1
This table entry is used to configure the following parameters for an IPv6 source/destination address -
Prefix, PrefixLen,Ifindex,Preference,Label,Address Type,IsSelfAddress, IsAddressPublic,
IsAddressDeprecated, Reacha…
Indexes
Column Syntax OID
fsipv6AddrSelPolicyPrefix
The IPv6 Address/Prefix for which the policy needs to be configured.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.1
fsipv6AddrSelPolicyPrefixLen
The Prefix length associated with the IPV6 address identified by 'fsipv6AddrSelPolicyPrefix.
Integer32
Constraints:
range: 1-128
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.2
fsipv6AddrSelPolicyIfIndex
The index value that uniquely identifies the interface to
which this entry is applicable. A value of 0 indicates that the associated address is reachable
via any interface.
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.3
fsipv6AddrSelPolicyScope
This MIB object identifies the scope of the IPv6 address. This can take the following values based on
whether the address is unicast/anycast or multicast.
0 reserved
1 Interface-Local scope
2 Link-Local scope
…
Integer32
Constraints:
range: 0-15
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.4
fsipv6AddrSelPolicyPrecedence
The precedence value associated with the address in the policy table. This value is applicable for
destination addresses.Higher the value, higher the precedence.
Integer32r/w
Constraints:
range: 1-128
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.5
fsipv6AddrSelPolicyLabel
The label value associated with the address in the policy table.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.6
fsipv6AddrSelPolicyAddrType
This MIB object is used to configure an address as unicast/anycast/multicast, provided the
IPv6 address meets the validation criteria for the address type.
Enumerationr/w
Enumerated Values:
1unicast
2anycast
3multicast
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.7
fsipv6AddrSelPolicyIsPublicAddr
This MIB object indicates whether the address configured in the policy table is a private or public
address.
Enumeration
Enumerated Values:
1true
2false
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.8
fsipv6AddrSelPolicyIsSelfAddr
This MIB object indicates whether the given address is configured on the associated interface
and represents a self-address. The associated MIB object fsipv6AddrSelPolicyIfIndex takes value true
if the associated IPv6 …
Enumeration
Enumerated Values:
1true
2false
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.9
fsipv6AddrSelPolicyReachabilityStatus
This MIB object indicates whether the address configured in the Policy Table is reachable/unreachable
Enumeration
Enumerated Values:
1reachable
2unreachable
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.10
fsipv6AddrSelPolicyConfigStatus
This MIB object indicates whether the associated entry in the Policy table is created automatically or
via the administrator.
Enumeration
Enumerated Values:
1automatic
2management
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.11
fsipv6AddrSelPolicyRowStatus
Administrative Status of the policy table. This object is used
to create or delete the entry in the policy table. The following values
are not supported for this MIB object - CREATE_AND_GO.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.10876.101.1.28.1.2.14.1.12

fsipv6IfScopeZoneMapTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.15 · 1 row entry · 17 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6IfScopeZoneMapTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6IfScopeZoneMapTable' 
A zone index identifies an instance of  a specific scope uniquely 
within the system.The zone index is used to associate unambiguously 
an IPv6 address to a specific zone.
          
Following are the changes that has been done in fsipv6IfScopeZoneMapTable
          
    1) The Zone-Index which is of type InetZoneIndex in stdipvx.mib
       is changed to DisplayString for user convenience.As the user is 
       aware of the zones by the scope-zone name rather than the index
       (i.e Linklocal1 or sitelocal1,scope61,scope71) it has been changed 
       to DisplayString. But the index associated with the scope-zone is 
       displayed by ipv6ScopeZoneIndexTable.
    2) The InetZoneIndex definition in INET-ADDRESS-MIB says that the zone-index 
       will typically be the interface index for link-local address, but as per 
       the design the Zone-Index is taken as a free flowing number starting 
       from the value 1, hence the value of ipv6ScopeZoneIndexLinkLocal shall not be                                                 
       complaint with InetZoneIndex definition.
     3) It is also mentioned that the zone-index value of 0 refers to the default 
       zone. But the design implements the default scope-zone index for every                                                
       scope by the fsipv6ScopeMemberEntry mib table. Hence the default-zone index 
       of value 0 is also not supported 
    4) The scope-zone index that are not configured on an interface shall take a
       alpha numeric value of invalid in FsIpv6IfScopeZoneMapEntry and -1 for the 
       index value in ipv6ScopeZoneIndexTable.
fsipv6IfScopeZoneMapEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.15.1
Each entry contains the list of scope identifiers on a given
interface. Its a unique value assigned for each scope on an
interface.
Indexes
Column Syntax OID
fsipv6ScopeZoneIndexIfIndex
The index value that uniquely identifies the interface to
which these scopes belong. The interface identified by a
particular value of this index is the same interface as
identified by the same value of the IF-MIB's if…
IF-MIBInterfaceIndex
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.1
fsipv6ScopeZoneIndexInterfaceLocal
The zone index for the Interface local scope on this interface.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.2
fsipv6ScopeZoneIndexLinkLocal
The zone index for the link-local scope on this interface.
The index value corresponding to this scope-zone can be known from
ipv6ScopeZoneIndexLinkLocal
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.3
fsipv6ScopeZoneIndex3
The zone index for scope 3 on this interface. The index value corresponding
to this scope-zone can be known from ipv6ScopeZoneIndex3
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.4
fsipv6ScopeZoneIndexAdminLocal
The zone index for the admin-local scope on this interface.The index value
corresponding to this scope-zone can be known from ipv6ScopeZoneIndexAdminLocal
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.5
fsipv6ScopeZoneIndexSiteLocal
The zone index for the site-local scope on this interface.The index value
corresponding to this scope-zone can be known from ipv6ScopeZoneIndexSiteLocal
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.6
fsipv6ScopeZoneIndex6
The zone index for scope 6 on this interface.The index value
corresponding to this scope-zone can be known from ipv6ScopeZoneIndex6
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.7
fsipv6ScopeZoneIndex7
The zone index for scope 7 on this interface.The index value
corresponding to this scope-zone can be known from ipv6ScopeZoneIndex7
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.8
fsipv6ScopeZoneIndexOrganizationLocal
The zone index for the organization-local scope on this
interface.The index value corresponding to this scope-zone
can be known from ipv6ScopeZoneIndexOrganizationLocal
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.9
fsipv6ScopeZoneIndex9
The zone index for scope 9 on this interface.The index value
corresponding to this scope-zone can be known from
ipv6ScopeZoneIndex9
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.10
fsipv6ScopeZoneIndexA
The zone index for scope A on this interface.The index value
corresponding to this scope-zone can be known from
ipv6ScopeZoneIndexA
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.11
fsipv6ScopeZoneIndexB
The zone index for scope B on this interface.The index value
corresponding to this scope-zone can be known from
ipv6ScopeZoneIndexB
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.12
fsipv6ScopeZoneIndexC
The zone index for scope C on this interface.The index value
corresponding to this scope-zone can be known from
ipv6ScopeZoneIndexC
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.13
fsipv6ScopeZoneIndexD
The zone index for scope D on this interface.The index value
corresponding to this scope-zone can be known from
ipv6ScopeZoneIndexD
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.14
fsipv6ScopeZoneIndexE
The zone index for scope E on this interface.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.15
fsipv6IfScopeZoneCreationStatus
Flag to determine if the scope-zone index is configured automatically
or by configuration.When an IPv6 interface is created by default the
linklocal scope is created and the creation status of it is automatic.When
a use…
Enumeration
Enumerated Values:
0notcreated
1automatic
2mgmt
3overridden
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.16
fsipv6IfScopeZoneRowStatus
The rowstatus of the scope-zone index table, used in
accordance to creation and deletion of scope-zones.To create
a row in this table manager sets this object to createAndGo(4).
The rowentry can be deleted automaticall…
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.10876.101.1.28.1.2.15.1.17

fsipv6ScopeZoneTable

table
.1.3.6.1.4.1.10876.101.1.28.1.2.16 · 1 row entry · 5 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6ScopeZoneTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6ScopeZoneTable' 
The table is used to map each scope-zone index 
with the interface to which it has been associated.
This table is indeed used while forwarding packets 
to find out what all interfaces belong to a particular 
scope-zone
fsipv6ScopeZoneEntry row .1.3.6.1.4.1.10876.101.1.28.1.2.16.1
An entry in the Scope-Zone Index Member Table.Each
entry specifies the interface indices associated with
a particular scope-zone index
Indexes
Column Syntax OID
fsipv6ScopeZoneName
Displays the scope zone name value(i.e linklocal1,
interfacelocal2) for the scope-zone index
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.10876.101.1.28.1.2.16.1.1
fsipv6ScopeZoneIndex
A unique value for each scope
on an interface. It is recommended that values are
assigned contiguously starting from 1.
INET-ADDRESS-MIBInetZoneIndex .1.3.6.1.4.1.10876.101.1.28.1.2.16.1.2
fsipv6ScopeZoneCreationStatus
Flag to determine if the scope-zone index is configured automatically
or by configuration.When an IPv6 interface is created by default the
linklocal scope is created and the creation status of it is automatic.When
a use…
Enumeration
Enumerated Values:
1automatic
2mgmt
3overridden
 .1.3.6.1.4.1.10876.101.1.28.1.2.16.1.3
fsipv6ScopeZoneInterfaceList
This MIB object displays all the interfaces that are part of/members of this
scope-zone index. These interfaces have the corresponding bit set in the octetlist.
InterfaceList .1.3.6.1.4.1.10876.101.1.28.1.2.16.1.4
fsipv6IsDefaultScopeZone
yes- indicates that zone is default zone for the associated scope
No - indicates that zone is not the default zone for the associated scope
Enumerationr/w
Enumerated Values:
1yes
2no
 .1.3.6.1.4.1.10876.101.1.28.1.2.16.1.5

fsipv6RouteTable

table
.1.3.6.1.4.1.10876.101.1.28.6.1 · 1 row entry · 12 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6RouteTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6RouteTable' 
This table contains dynamic routes that are learnt
through dynamic routing protocol as well as local routes
derived from configured address prefixes and statically
configured routes.
fsipv6RouteEntry row .1.3.6.1.4.1.10876.101.1.28.6.1.1
An entry in the IPv6 Routing Table. An entry can be created
by means of the routing protocol, derived from configured
address prefixes as well as statically configured. There
can be a static route as well as dynamic rou…
Indexes
Column Syntax OID
fsipv6RouteDest
The destination IPv6 address of this route.
This object will not take a Link-Local or Multicast address
value.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.1
fsipv6RoutePfxLength
Indicates the prefix length of the destination
address.
Integer32
Constraints:
range: 1-128
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.2
fsipv6RouteProtocol
The routing mechanism via which this route was
learned. If it has value local(2), it indicates this
route was derived from a configured address prefix.
Enumeration
Enumerated Values:
1other
2local
3netmgmt
4ndisc
5rip
6ospf
7bgp
8idrp
9igrp
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.3
fsipv6RouteNextHop
Next hop IPv6 Address for this route. For direct routes
it has the value ::0.
OctetString
Constraints:
range: 16-16
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.4
fsipv6RouteIfIndex
The index value which uniquely identifies the interface
through which the next hop of this route should be reached.
The interface identified by a particular value of this index
is the same interface as identified by the…
IF-MIBInterfaceIndexr/w
Type Constraints:
range: 1..2147483647
Description:
A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.5
fsipv6RouteMetric
The routing metric associated with this route.
Unsigned32r/w
Constraints:
range: 1-4294967295
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.6
fsipv6RouteType
The type of route. Note that 'local(3)' refers
to a route for which the next hop is the final
destination; 'remote(4)' refers to a route for
which the next hop is not the final
destination; 'discard(2)' refers to a r…
Enumerationr/w
Enumerated Values:
1other
2discard
3local
4remote
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.7
fsipv6RouteTag
This object specifies whether this route is an internal
or external route. Value 0 represent routes are internal
to the routing domain and Value > 0 represent routes
are external to the routing domain. For routes learnt…
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.8
fsipv6RouteAge
The number of seconds since this route was last
updated or otherwise determined to be correct. For
statically configured routes and locally derived routes,
this object has value 0.
SNMPv2-SMIInteger32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.9
fsipv6RouteAdminStatus
Administrative Status of the route. This object is used
to create or delete the route entry. The fsipv6RouteIfIndex
needs to be set, before the route entry is made active.
CreateAndGo is not supported.
SNMPv2-TCRowStatusr/w
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
Description:
The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.10
fsipv6RouteAddrType
Indicates whether the destination address in the route entry
is unicast or anycast.
Enumerationr/w
Enumerated Values:
1unicast
2anycast
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.11
fsipv6RouteHwStatus
Indicates whether the route entry is either present or not
present in the hardware.
Enumeration
Enumerated Values:
1present
2not-present
 .1.3.6.1.4.1.10876.101.1.28.6.1.1.12

fsipv6PrefTable

table
.1.3.6.1.4.1.10876.101.1.28.6.2 · 1 row entry · 2 columns
Open in standard view
Uses the supermicro variant from /opt/observium/mibs/supermicro.
Command help
Walk fsipv6PrefTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'SUPERMICRO-IPV6-MIB' -M '/opt/observium/mibs/supermicro:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'SUPERMICRO-IPV6-MIB::fsipv6PrefTable' 
The IPv6 Preference table contains information on the 
Preference Value for each supported protocol.
fsipv6PrefEntry row .1.3.6.1.4.1.10876.101.1.28.6.2.1
An entry containing objects about a particular protocols
preference value.
Indexes
Column Syntax OID
fsipv6Protocol
A unique value identifying the protocol whose preference
value needs to be processed.
Enumeration
Enumerated Values:
1other
2local
3netmgmt
4ndisc
5rip
6ospf
7bgp
8idrp
9igrp
 .1.3.6.1.4.1.10876.101.1.28.6.2.1.1
fsipv6Preference
Preference of the route learned by a particular protocol.
This value is used while choosing the best path.
Lesser the value, highest is the preference.
Unsigned32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.10876.101.1.28.6.2.1.2