SUPERMICRO-CFA-MIB Table View

A list of all the interface entries in the system. 
This table contains objects which are applicable to all
types of interfaces in the system. This table is a 
proprietary extension to the standard ifTable and 
ifXTable. The index to this table has the semantics of
the MIB-2 ifIndex.

ifMainEntry row .1.3.6.1.4.1.10876.101.1.27.1.4.1

An entry containing management information applicable
to a particular interface.

Indexes

ifMainIndex

Column	Syntax	OID
ifMainIndex A unique value, greater than zero, for each interface. This object is identical to the ifIndex of the standard MIB-2 ifTable.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.27.1.4.1.1
ifMainType The type/protocol of interface. Specification of the object is mandatory for all interfaces. This value should be specified after the row creation in the ifMainTable and before setting any other object in this table. On…	Enumerationr/w Enumerated Values: 5 rfc877x25 6 ethernetCsmacd 9 iso88025TokenRing 23 ppp 24 softwareLoopback 32 frameRelay 38 miox25 49 aal5 53 propVirtual 84 async 92 frameRelayMPI 108 pppMultilinkBundle 114 ipOverAtm 118 hdlc 131 tunnel 134 atmSubInterface 136 l3ipvlan 150 mplsTunnel 161 ieee8023ad 166 mpls 200 teLink 209 brgPort 246 ifPwType 247 ilan 248 pip	.1.3.6.1.4.1.10876.101.1.27.1.4.1.2
ifMainMtu The MTU for the interface as shown to the higher interface sub-layer (this value should not include the encapsulation or header added by the interface). If IP is operating over the vlan interface (not include router po…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.27.1.4.1.3
ifMainAdminStatus The desired state of the interface. This object can be set only when the ifMainRowStatus of the interface is active. This object has the semantics of the ifAdminStatus of the standard ifTable. The testing…	Enumerationr/w Enumerated Values: 1 up 2 down 3 testing 4 loopback	.1.3.6.1.4.1.10876.101.1.27.1.4.1.4
ifMainOperStatus The current operational state of the interface. The testing (3) state indicates that no operational packets can be passed - this state is not supported currently. If ifMainAdminStatus is down (2) then if…	Enumeration Enumerated Values: 1 up 2 down 3 testing 4 unknown 5 dormant 6 notPresent 7 lowerLayerDown	.1.3.6.1.4.1.10876.101.1.27.1.4.1.5
ifMainEncapType The encapsulation type to be used over the interface. For Ethernet interfaces, the default encapsulation type is ethernetV2(8). The other possible encapsulation is llcSnap(6). If other(1) is specified the…	Enumerationr/w Enumerated Values: 1 other 2 nlpid 3 nlpidSnap 4 cudNlpid 5 cudNlpidSnap 6 llcSnap 7 vcMultiplexed 8 ethernetV2	.1.3.6.1.4.1.10876.101.1.27.1.4.1.6
ifMainBrgPortType The Bridge port type of this specified switch port. Bridge Port type can be specified only for switch ports and not for router ports, IVR interfaces and I-LAN Interfaces. providerNetworkPort - Port Conne…	Enumerationr/w Enumerated Values: 1 providerNetworkPort 2 customerNetworkPortPortBased 3 customerNetworkPortStagged 4 customerEdgePort 5 propCustomerEdgePort 6 propCustomerNetworkPort 7 propProviderNetworkPort 8 customerBridgePort 9 customerNetworkPortCtagged 10 virtualInstancePort 11 providerInstancePort 12 customerBackbonePort	.1.3.6.1.4.1.10876.101.1.27.1.4.1.7
ifMainRowStatus A RowStatus variable for addition, deletion and in-activation of the interfaces. Specification of the object is mandatory for all interfaces. When the status is active, the interface is created and ready …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.4.1.8
ifMainSubType This object stores the subType value of the specified interface. Configuration of this object is not mandatory.By default Sub type value will be updated based on the hardware link speed. For non Ethernet …	Enumerationr/w Enumerated Values: 251 extremeEther 252 fastEther 253 gigabitEthernet 254 xlEthernet 255 notApplicable	.1.3.6.1.4.1.10876.101.1.27.1.4.1.9
ifMainNetworkType This object indicates whether this interface is a WAN or LAN link. The default value for this object varies according to the interface type. All interfaces of type radio (71), ieee8023ad (161) and l3ipvl…	Enumerationr/w Enumerated Values: 1 lan 2 wan	.1.3.6.1.4.1.10876.101.1.27.1.4.1.10
ifMainWanType This object indicates whether this interface is a private or public WAN link. This object is applicable only for PPP interfaces and ethernet WAN interfaces. For other interfaces the value cannot be set …	Enumerationr/w Enumerated Values: 0 other 1 private 2 public	.1.3.6.1.4.1.10876.101.1.27.1.4.1.11
ifMainDesc A textual string which contains the description about an interface.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.1.27.1.4.1.12
ifMainStorageType The storage type for this conceptual row in the ifMainTable. Conceptual rows having the value 'permanent' need not allow write-access to any columnar object in the row. only volatile and nonVolatile are allowed for thi…	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.4.1.10876.101.1.27.1.4.1.13
ifMainExtSubType This object stores the subType value of the specified interface. These sub types are specified for the ifMainType-propVirtual.	Enumerationr/w Enumerated Values: 0 sisp 1 attachmentCircuit 2 openflow	.1.3.6.1.4.1.10876.101.1.27.1.4.1.14
ifMainRportL3Mtu This value indicates the L3 MTU for router port, and is not applicable for other interface type. The lenght of ethernet header is also included. For router port, ifMainMtu means L2 MTU. L3 MTU should les…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.10876.101.1.27.1.4.1.15

A list of all the interface entries in the system which
are registered with IP.
                
This table contains objects which are applicable for the
management of IP over the network interfaces
in the system. 
             
This table is a extension to the ifMainTable. 
The index to this table has the semantics of
the ifMainIndex of the ifMainTable.
                
Entries are created automatically in this table for
any interface sub-layer which is layer below IP using
the ifStackTable. Similarly, entries are deleted from
this table when the interface's layering below IP is
removed.

ifIpEntry row .1.3.6.1.4.1.10876.101.1.27.1.5.1

An entry containing management information applicable
to a particular interface over which IP is operating.

Indexes

ifMainIndex

Column	Syntax	OID
ifIpAddrAllocMethod The mechanism to be used for allocation of IP address for this interface. The value negotiation can be used only for PPP and MLPPP interfaces which support obtaining of IP addresses through negotiation. …	Enumerationr/w Enumerated Values: 1 manual 2 negotiation 3 dynamic 4 none	.1.3.6.1.4.1.10876.101.1.27.1.5.1.1
ifIpAddr Specifies the IP address given to this interface. The specification of this object is mandatory for all network interfaces (Ethernet, FR VC, IPoA interface, PPP link - not under MP, MP interface and X.25 VC). If the int…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.5.1.2
ifIpSubnetMask Specifies the IP Subnet Mask for this interface. The value should be specified only for network interfaces and any valid VLSM is accepted. If not specified, this object takes the default subnet mask valu…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.5.1.3
ifIpBroadcastAddr Specifies the IP broadcast address for this interface. The value should be specified only for network interfaces and any valid broadcast address based on a valid VLSM is accepted. If not specified, this …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.5.1.4
ifIpForwardingEnable Specifies whether IP forwarding is enable on this interface. Disabling IP forwarding on an interface will result in packets which are to be forwarded on that interface being dropped and ICMP error messages being generat…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.27.1.5.1.5
ifIpAddrAllocProtocol Specifies the protocol to be used to obtain IP address for this interface. This object is valid only when ifIpAddrAllocMethod is set to dynamic (3). When ifIpAddrAllocMethod option is dhcp(2) dhcp-cli…	Enumerationr/w Enumerated Values: 1 rarp 2 dhcp	.1.3.6.1.4.1.10876.101.1.27.1.5.1.6
ifIpDestMacAddress The unicast Peer MacAddress for unnumbered interface. This Object needs to be configured mandatorily for proper forwarding of IP packets over unnumbered interfaces.This object needs to be set to avoid ARP resolution fai…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.10876.101.1.27.1.5.1.7
ifIpUnnumAssocIPIf This object stores the interface index of the interface associated with the unnumbered interface. The source IP addresses used over the Unnumbered interface in relation to the destination IP address are borrowed from th…	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.27.1.5.1.8

A list of all the interfaces in the system with IVR related
configurations.
          
This table is an extension to the ifMainTable. The index to 
this table has the semantics of the ifMainIndex of the 
ifMainTable.

ifIvrEntry row .1.3.6.1.4.1.10876.101.1.27.1.8.1

An entry containing IVR-related information applicable
to a interface.

Indexes

ifMainIndex

Column	Syntax	OID
ifIvrBridgedIface Indicates if this interface is a Bridged interface or not. A value of 'TRUE' indicates that this interface is a Bridged interface and is capable of performing bridging of packets through this interface. A value of 'F…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.10876.101.1.27.1.8.1.1

A list of secondary IP addresses configured over the 
interfaces registered with IP.
                
This table is a extension to the ifMainTable. 
The index to this table has the semantics of
the ifMainIndex of the ifMainTable.
          
Secondary IpAddress configuration should not override the 
primary ip address configured for any of the interface
          
Updation of entries in this table are not allowd when 
RowStatus is active

ifSecondaryIpAddressEntry row .1.3.6.1.4.1.10876.101.1.27.1.11.1

An entry contains the information associated with the
secondary(additional) ip address configured to a particular
interface.

Indexes

ifMainIndex ifSecondaryIpAddress

Column	Syntax	OID
ifSecondaryIpAddress Specifies the Secondary IP address associated with the interface	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.11.1.1
ifSecondaryIpSubnetMask Specifies the IP Subnet Mask associted with the secondary ip address configuration. The value should be specified only for network interfaces and any valid VLSM is accepted. If not specified, this obje…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.11.1.2
ifSecondaryIpBroadcastAddr Specifies the IP broadcast address associated with the configured secondary IP address. The value should be specified only for network interfaces and any valid broadcast address based on a valid VLSM is accepted. …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.10876.101.1.27.1.11.1.3
ifSecondaryIpRowStatus This object is used to manage creation and deletion of rows in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.11.1.4

This table is an extension to the ifMainTable.

ifMainExtEntry row .1.3.6.1.4.1.10876.101.1.27.1.12.1

An entry containing additional management information
applicable to a particular interface.

Indexes

No indexes recorded

Column	Syntax	OID
ifMainExtMacAddress The unicast MacAddress for each interface. The Macaddress can be set only when ifMainAdminStatus for the interface is down(2). The object is valid only for interfaces that have the ifMainType set as ethernetCsmacd(6) …	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.10876.101.1.27.1.12.1.8
ifMainExtSysSpecificPortID System specific index configured for the port. It provides a different numbering space other than the IfIndex to identify ports. Valid range for this object is from 1 to 16384. The value 0 is not allowed to be set. O…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.1.12.1.9
ifMainExtInterfaceType This object reflects the usage of this interface, whether it is a frontpanel interface or a backplane interface used for interswitching in distributed environments. frontpanelport - The interface behave…	Enumerationr/w Enumerated Values: 1 frontpanelport 2 backplaneport	.1.3.6.1.4.1.10876.101.1.27.1.12.1.10
ifMainExtPortSecState The interface port security state says whether the port is connected to trusted hosts or not. If a port is trusted, the packets coming on that ports will also be trusted. By default all the ports will be trusted	Enumerationr/w Enumerated Values: 0 untrusted 1 trusted	.1.3.6.1.4.1.10876.101.1.27.1.12.1.11

This table allows generic TLV data to be configured per-port.
It may be used to store any port-specific information that 
is required by any application.

ifCustTLVEntry row .1.3.6.1.4.1.10876.101.1.27.1.13.1

Entry about the TLV information

Indexes

ifMainIndex ifCustTLVType

Column	Syntax	OID
ifCustTLVType Type of the TLV Information.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.1.13.1.1
ifCustTLVLength Length of the TLV Information. Specification of this object is mandatory for ifCustTLVRowStatus to be made active. Length should be configured after the row creation in ifCustTLVTable and before configuring the ifCust…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.1.13.1.2
ifCustTLVValue Value of the TLV Information. The default value is 0.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.10876.101.1.27.1.13.1.3
ifCustTLVRowStatus RowStatus of the Corresponding Entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.13.1.4

This table allows generic integer attributes to be configured 
per-port. These attributes will be opaque from ISS's point of 
view and will not be processed/understood by ISS.

ifCustOpaqueAttrEntry row .1.3.6.1.4.1.10876.101.1.27.1.14.1

Entry for every opaque attribute on each port.

Indexes

ifMainIndex ifCustOpaqueAttributeID

Column	Syntax	OID
ifCustOpaqueAttributeID OpaqueAttribute ID configured on the port. Four opaque attributes are supported on each port	Enumeration Enumerated Values: 1 opaqueAttr1 2 opaqueAttr2 3 opaqueAttr3 4 opaqueAttr4	.1.3.6.1.4.1.10876.101.1.27.1.14.1.1
ifCustOpaqueAttribute Value for the Opaque attribute.This value can be altered when ifCustOpaqueRowStatus is ACTIVE.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.1.14.1.2
ifCustOpaqueRowStatus RowStatus of the Corresponding Entry. NOT_IN_SERVICE value is not supported.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.14.1.3

This table is used to read the status of an I-Lan interface
created from Iftable. An I-LAN Interface is
 used to create internal connections between bridge ports in a
 802.1 device.  An I-LAN Interfaces can be directly associated
 with a set of bridge ports.  An I-LAN Interfaces can also be
 used as a stacking interface to relate other interfaces before
 association to bridge ports.
          
 For example, an I-LAN interface can be created to link traffic
 between a PIP and a CBP.  This involves creation of an interface
 of type iLan with a corresponding entry made in the ifTable. 
           
 The IfIndex corresponding to the ILAN is put in the IlanifTable.
 A CBP is created in a B Component of IfType internal and  CBP 
 related IfEntry is stacked upon the IfEntry of the I-LAN using 
 the IfStackTable.  Similarly, a PIP is created in a I Component
 of IfType internal and  PIP related IfEntry is stacked upon the
 IfEntry of the I-LAN using the IfStackTable. 
 Finally, a VIP is created with ifType internal on the I-Component
 and is associated with the PIP, thus completing the path from 
 the I-Component's MAC relay to the CBP on the B-Component.
          
 Entries in this table must be persistent over power up
 restart/reboot.

ifBridgeILanIfEntry row .1.3.6.1.4.1.10876.101.1.27.1.15.1

Each entry consists of a Status to get the I-Lan interface status

Indexes

IF-MIBifIndex

Column	Syntax	OID
ifBridgeILanIfStatus This object is used to read the status of an I-Lan interface created from Iftable.	Enumeration Enumerated Values: 1 active 2 outOfService	.1.3.6.1.4.1.10876.101.1.27.1.15.1.1

A table to configure the interface types and bridge port types accessible 
to various protocol(s). This table will indicate whether
a particular type of interface is to be created or be visible
in the given protocol module. An entry in this table will cause the 
particular type of interface to be denied from being accessed by the 
protocol i.e. the particular type of interface will not be created
(i.e. visible) in the given protocol.

ifTypeProtoDenyEntry row .1.3.6.1.4.1.10876.101.1.27.1.16.1

Each entry in this table will give the interface type and bridge port type
that will not be accessible to the protocol for the mentioned context.
Only valid and allowed combinations of ifTypeProtoDenyMainType and
ifTyp…

Indexes

ifTypeProtoDenyContextId ifTypeProtoDenyMainType ifTypeProtoDenyBrgPortType ifTypeProtoDenyProtocol

Column	Syntax	OID
ifTypeProtoDenyContextId Identifies a virtual context in which to deny access of the given interface type and bridge port type to a protocol.	Unsigned32 Constraints: range: 0-255	.1.3.6.1.4.1.10876.101.1.27.1.16.1.1
ifTypeProtoDenyMainType This object type refers to the ifMainType. The interface types that are currently supported by this table are ethernetCsmacd(6), propVirtual(53), ieee8023ad(161), brgPort(209) and pip(248).	Enumeration Enumerated Values: 6 ethernetCsmacd 53 propVirtual 161 ieee8023ad 209 brgPort 248 pip	.1.3.6.1.4.1.10876.101.1.27.1.16.1.2
ifTypeProtoDenyBrgPortType This object type refers to ifMainBrgPortType.	Enumeration Enumerated Values: 1 providerNetworkPort 2 customerNetworkPortPortBased 3 customerNetworkPortStagged 4 customerEdgePort 5 propCustomerEdgePort 6 propCustomerNetworkPort 7 propProviderNetworkPort 8 customerBridgePort 9 customerNetworkPortCtagged 10 virtualInstancePort 11 providerInstancePort 12 customerBackbonePort	.1.3.6.1.4.1.10876.101.1.27.1.16.1.3
ifTypeProtoDenyProtocol Identifies the protocol for which the corresponding interface type and bridge port type will not be accessible/visible.	Enumeration Enumerated Values: 1 pnac 2 la 3 xstp 4 vlan 5 garp 6 mrp 7 pbb 8 ecfm 9 elmi 10 snoop 11 lldp 12 bridge 13 qos	.1.3.6.1.4.1.10876.101.1.27.1.16.1.4
ifTypeProtoDenyRowStatus Indicates the status of the row. Valid values are 'createAndGo' and 'destroy'. A row can be created in this table by assigning the value 'createAndGo' for the status object which will cause the entry to become active.…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.16.1.5

This table is used to configure the list of vlans to be 
associated for an IVR interface.
The primary Index to this table can only be a IVR interface.

ifIvrMappingEntry row .1.3.6.1.4.1.10876.101.1.27.1.18.1

Each entry in this table gives an assoicated vlan to an IVR
interface.

Indexes

ifMainIndex ifIvrAssociatedVlan

Column	Syntax	OID
ifIvrAssociatedVlan This object specifies one of the associated VLANs for a given IVR interface. Vlan Id associated with an IVR interface during IVR interface creation, should not be configured as ifIvrAssociatedVlan for that IVR interfac…	Q-BRIDGE-MIBVlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.10876.101.1.27.1.18.1.1
ifIvrMappingRowStatus Denotes the Row Status for port isolation table entry. Only 'CreateAndGo' and 'destroy' values are allowed for this object. 'CreateAndWait' and 'notInService' values are not allowed. Example: To add vlans 2, 3 as ass…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.1.18.1.2

A list of interface entries.  The number of entries is
given by the value of ifNumber.  This table contains
additional objects for the interface table.

ifHCErrorEntry row .1.3.6.1.4.1.10876.101.1.27.1.19.1

An entry containing additional management information
applicable to a particular interface.

Indexes

No indexes recorded

Column	Syntax	OID
ifHCInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.10876.101.1.27.1.19.1.1
ifHCInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character- oriented or fixed-length interfaces, the number of i…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.10876.101.1.27.1.19.1.2
ifHCInUnknownProtos For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protoc…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.10876.101.1.27.1.19.1.3
ifHCOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.10876.101.1.27.1.19.1.4
ifHCOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.10876.101.1.27.1.19.1.5

This table returns the next available free interface
index for the given interface type

ifAvailableIndexEntry row .1.3.6.1.4.1.10876.101.1.27.1.24.1

This is an entry in the ifAvailableFreeIndex Table

Indexes

IF-MIBifType

Column	Syntax	OID
ifAvailableFreeIndex This is the next available free interfac index for a given ifType	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.27.1.24.1.1

A list of Attachment Circuit interface related
configurations. Attachment Circuit is a virtual interface
that is a  combination of physical port and customer vlan
identifier or it is a virtual interface that contains
underlying physical port alone.
          
This table is an extension to the ifMainTable. The index to
this table has the semantics of the ifMainIndex of the
ifMainTable.

ifACEntry row .1.3.6.1.4.1.10876.101.1.27.1.25.1

An entry containing AC-related information applicable
to attachment cirucit interface only.

Indexes

ifMainIndex

Column	Syntax	OID
ifACPortIdentifier This is the physical interface on which the attachment circuit interface is present. The operational status of the attachment circuit interface depends on this port's operational status. That is if the operational statu…	IF-MIBInterfaceIndexr/w Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.10876.101.1.27.1.25.1.1
ifACCustomerVlan This is the customer vlan present for the attachment circuit interface. This object alone can not determine the attachment circuit interface. To determine that, this object should be together present with the ifACPortId…	Q-BRIDGE-MIBVlanIdr/w Type Constraints: range: 1..4094	.1.3.6.1.4.1.10876.101.1.27.1.25.1.2

This table is used by the Packet Analyser for 
Pattern matching on particular ports

fsPacketAnalyserEntry row .1.3.6.1.4.1.10876.101.1.27.5.1.1

An entry containing Pattern matching information
used by the Packet analyser

Indexes

fsPacketAnalyserIndex

Column	Syntax	OID
fsPacketAnalyserIndex An arbitrary integer value, greater than zero, which uniquely identifies a pattern to be matched	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.1.1.1
fsPacketAnalyserWatchValue This represents the pattern which is to be matched in the packet to be analysed by the packet analyser	OctetStringr/w Constraints: range: 0-1600	.1.3.6.1.4.1.10876.101.1.27.5.1.1.2
fsPacketAnalyserWatchMask The mask for the pattern to be matched by the packet analyser	OctetStringr/w Constraints: range: 0-1600	.1.3.6.1.4.1.10876.101.1.27.5.1.1.3
fsPacketAnalyserWatchPorts Specifies the complete set of ports over which the pattern is to be matched by the packet analyser	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.27.5.1.1.4
fsPacketAnalyserMatchPorts Specifies the complete set of ports over which the pattern is matched by the packet analyser	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.10876.101.1.27.5.1.1.5
fsPacketAnalyserCounter Number of times the pattern was matched over the watched ports	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.1.1.6
fsPacketAnalyserTime The value of sysUpTime when the pattern was last matched	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.1.1.7
fsPacketAnalyserCreateTime The value of sysUpTime when the system was initiated	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.1.1.8
fsPacketAnalyserStatus Specifies the Row Status for the entry in this table	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.5.1.1.9

This table is used by the Packet Transmitter for 
sending the packets on particular ports

fsPacketTransmitterEntry row .1.3.6.1.4.1.10876.101.1.27.5.2.1

An entry containing Packet information
used by the Packet Transmitter

Indexes

fsPacketTransmitterIndex

Column	Syntax	OID
fsPacketTransmitterIndex An arbitrary integer value, greater than zero, which uniquely identifies a packet to be sent	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.2.1.1
fsPacketTransmitterValue This represents the pattern which is to be sent through the given port by the packet transmitter	OctetStringr/w Constraints: range: 0-1600	.1.3.6.1.4.1.10876.101.1.27.5.2.1.2
fsPacketTransmitterPort Specifies the port over which the packet is to be sent by the packet transmitter	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.10876.101.1.27.5.2.1.3
fsPacketTransmitterInterval The Time interval for sending the packet over the port in seconds	SNMPv2-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.2.1.4
fsPacketTransmitterCount Number of packet to be sent over the ports	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.10876.101.1.27.5.2.1.5
fsPacketTransmitterStatus Specifies the Row Status for the entry in this table	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.10876.101.1.27.5.2.1.6