SPAGENT-MIB Table View

This table contains the data for every Temperature Sensor in the SensorArray. Each row in the table contains data for a different Temperature Sensor.

sensorProbeTempEntry row .1.3.6.1.4.1.3854.1.2.2.1.16.1

This is an entry in the sensorProbeTempEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeTempDescriptionmandatory A Description of this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.1
sensorProbeTempLocationmandatory The physical location of this sensor	RFC1213-MIBDisplayStringr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.16.1.2
sensorProbeTempDegreemandatory The degrees in this sensor	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.3
sensorProbeTempStatusmandatory The current status of this Sensor	Enumeration Constraints: range: -32768-32767	.1.3.6.1.4.1.3854.1.2.2.1.16.1.4
sensorProbeTempOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.16.1.5
sensorProbeTempGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.6
sensorProbeTempHighWarningmandatory How hot this sensor gets before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.7
sensorProbeTempHighCriticalmandatory How hot this sensor gets before it sends a critical event	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.8
sensorProbeTempLowWarningmandatory How cold this sensor gets before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.9
sensorProbeTempLowCriticalmandatory How cold this sensor gets before it sends a critical event	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.10
sensorProbeTempRearmmandatory The number of degrees to rearm the status. For example if status goes from normal to warning, the temp must go down spTempRearm degrees below warning before the status goes to normal	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.11
sensorProbeTempDegreeTypemandatory The degrees are in fahrenheit(0) or in celsius(1)	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.12
sensorProbeTempSensorTypemandatory The type of temperture sensor	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.13
sensorProbeTempDegreeRawmandatory SP Only: The raw degree data from the temperature sensor, slightly higher resolution	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.14
sensorProbeTempEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w Constraints: range: 0-65534	.1.3.6.1.4.1.3854.1.2.2.1.16.1.16
sensorProbeTempEmailTrapSchedulemandatory SP Only: Email/trap limit schedule for this sensor	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65534	.1.3.6.1.4.1.3854.1.2.2.1.16.1.17
sensorProbeTempEmailTrapIntervalmandatory Minimum time between each [email/trap:SP, only trap:CP8] (can be from 0 to 60 minutes).	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.18
sensorProbeTempSendNormalTrapmandatory Enable sending email/trap when sensor goes to normal	Enumerationr/w Constraints: range: 0-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.19
sensorProbeTempDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.20
sensorProbeTempDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.21
sensorProbeTempIndexmandatory The index into the temperature sensor table	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.22
sensorProbeTempRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.23
sensorProbeTempRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.24
sensorProbeTempRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.25
sensorProbeTempRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.26
sensorProbeTempEmailIntervalmandatory CP8 Only: Minimum time between each email (can be from 0 to 60 minutes)	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.27
sensorProbeTempIndexCountmandatory Number of Temperature sensor online	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.28
sensorProbeTempOffsetmandatory Temperature Offset reading	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.29
sensorProbeTempSirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.30
sensorProbeTempSirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.31
sensorProbeTempSirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.32
sensorProbeTempSirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.33
sensorProbeTempAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.34
sensorProbeTempSirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.35
sensorProbeTempURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.36
sensorProbeTempOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.16.1.37
sensorProbeTempDatacollectTypemandatory Type of datacollect to collect.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.38
sensorProbeTempContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.39
sensorProbeTempContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.40
sensorProbeTempContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.16.1.41
sensorProbeTempContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.42
sensorProbeTempContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.43
sensorProbeTempContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.44
sensorProbeTempCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.45
sensorProbeThermostatIndexmandatory A unique value for each sensor thermostat port.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.46
sensorProbeThermostatDescriptionmandatory A Description of this sensor thermostat	RFC1213-MIBDisplayStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.47
sensorProbeThermostatValuemandatory The value in this sensor	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.48
sensorProbeThermostatOnlinemandatory If this Sensor is currently online	Enumeration Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.49
sensorProbeThermostatGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.50
sensorProbeThermostatModemandatory To select the thermostat mode for working on time-bases(1) or normal(0).	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.51
sensorProbeThermostatRelayControlPortmandatory To select a relay port to be controled by this thermostat sensor.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.16.1.52
sensorProbeThermostatNormalAction1mandatory Profile1: Thermostat normal action for controlling a relay sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.53
sensorProbeThermostatHighLimit1mandatory Profile1: When this sersor higher than thermostat high limit, it will take a high limit action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.54
sensorProbeThermostatHighLimitAction1mandatory Profile1: Thermostat high limit action for controlling a relay sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.55
sensorProbeThermostatLowLimit1mandatory Profile1: When this sersor higher than thermostat low limit, it will take a normal limit action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.56
sensorProbeThermostatLowLimitAction1mandatory Profile1: Thermostat low limit action for controlling a relay sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.57
sensorProbeThermostatNormalAction2mandatory Profile2: Thermostat normal action for controlling a relay sensor.	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.16.1.58
sensorProbeThermostatHighLimit2mandatory Profile2: When this sersor higher than thermostat high limit, it will take a high limit action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.59
sensorProbeThermostatHighLimitAction2mandatory Profile2: Thermostat high limit action for controlling a relay sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.60
sensorProbeThermostatLowLimit2mandatory Profile2: When this sersor higher than thermostat low limit, it will take a normal limit action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.61
sensorProbeThermostatLowLimitAction2mandatory Profile2: Thermostat low limit action for controlling a relay sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.62
sensorProbeThermostatEnableTimemandatory Time to enable on Thermostat	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.63
sensorProbeTempSendNormalMailmandatory Enable sending email when sensor goes to normal	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.64
sensorProbeTempSendTrapmandatory Enable sending trap when sensor change status	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.16.1.65
sensorProbeTempSendMailmandatory Enable sending email when sensor change status	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.16.1.66

This table contains the data for every Humidity Sensor in the SensorArray. Each row in the table contains data for a different Humidity Sensor.

sensorProbeHumidityEntry row .1.3.6.1.4.1.3854.1.2.2.1.17.1

This is an entry in the sensorProbeHumidityEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeHumidityDescriptionmandatory A Description of this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.1
sensorProbeHumidityLocationmandatory The physical location of this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.2
sensorProbeHumidityPercentmandatory The relative humidity percentage measured by this sensor	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.17.1.3
sensorProbeHumidityStatusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.17.1.4
sensorProbeHumidityOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.17.1.5
sensorProbeHumidityGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.6
sensorProbeHumidityHighWarningmandatory How high the relative humidity this sensor measures before it sends a warning	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.17.1.7
sensorProbeHumidityHighCriticalmandatory How high the relative humidity this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.8
sensorProbeHumidityLowWarningmandatory How low the relative humidity this sensor measures before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.9
sensorProbeHumidityLowCriticalmandatory How low the relative humidity this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.10
sensorProbeHumidityRearmmandatory The percent relative humidity to rearm the status. For example if status goes from normal to warning, the humidity must go down spAnalogueRearm below warning before the status goes to normal	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.11
sensorProbeHumidityRawmandatory The unformatted, raw, A/D value in this sensor. Contains more resolution than the formated percentage. This number can go from 0 to 1023 depending on the input voltage	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.13
sensorProbeHumidityLowVoltagemandatory SP Only: The low voltage range for use in AtoD conversion.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.14
sensorProbeHumidityHighVoltagemandatory SP Only: The high voltage range for use in AtoD conversion.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.15
sensorProbeHumidityEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.17
sensorProbeHumidityEmailTrapSchedulemandatory SP Only: Email/trap limit schedule for this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.18
sensorProbeHumidityEmailTrapIntervalmandatory Minimum time between each [email/trap:SP, only trap:CP8] (can be from 0 to 60 minutes)	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.19
sensorProbeHumiditySendNormalTrapmandatory Enable sending email/trap when sensor goes to normal	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.20
sensorProbeHumidityDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.21
sensorProbeHumidityDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.22
sensorProbeHumidityIndexmandatory The index into the Humidity sensor table	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.17.1.23
sensorProbeHumidityAtoDAmountMaxVoltagemandatory The maximum scale of DC voltage conversion.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.24
sensorProbeHumidityAtoDAmountBaseVoltagemandatory The base scale of DC voltage conversion.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.25
sensorProbeHumidityAtoDTypeUnitmandatory Type of scale for use in DC voltage conversion.	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.17.1.26
sensorProbeHumidityDcUnitmandatory Display unit in DC voltage conversion.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.27
sensorProbeHumidityAtoDJumpermandatory Selected voltage scale (jumper 0) in DC voltage conversion.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.28
sensorProbeHumidityRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.29
sensorProbeHumidityRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.30
sensorProbeHumidityRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.31
sensorProbeHumidityRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.32
sensorProbeHumidityEmailIntervalmandatory CP8 Only: Minimum time between each emial (can be from 0 to 60 minutes)	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.33
sensorProbeHumidity4to20mAUnitmandatory Display unit in DC voltage conversion.	RFC1213-MIBDisplayStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.34
sensorProbeHumidityIndexCountmandatory Number of Humidity sensor online	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.35
sensorProbeHumidityOffsetmandatory Humidity Offset reading	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.17.1.36
sensorProbeHumiditySirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.37
sensorProbeHumiditySirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.38
sensorProbeHumiditySirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.39
sensorProbeHumiditySirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.40
sensorProbeHumidityAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.41
sensorProbeHumiditySirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.42
sensorProbeHumidityURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.17.1.43
sensorProbeHumidityOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.44
sensorProbeHumidityDatacollectTypemandatory Type of datacollect to collect.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.45
sensorProbeHumidityContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.46
sensorProbeHumidityContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.47
sensorProbeHumidityContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.48
sensorProbeHumidityContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.49
sensorProbeHumidityContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.50
sensorProbeHumidityContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.17.1.51
sensorProbeHumidityCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.52
sensorProbeHumiditySendNormalMailmandatory Enable sending email when sensor goes to normal	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.53
sensorProbeHumiditySendTrapmandatory Enable sending trap when sensor change status	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.54
sensorProbeHumiditySendMailmandatory Enable sending email when sensor change status	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.55
sensorProbeIDCVVoltateRatiomandatory iDCV calibrate voltate ratio	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.56
sensorProbeIDCVErrorFlagmandatory iDCV error flag	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.17.1.57
sensorProbeIDCVCalibratemandatory iDCV calibrate	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.58
sensorProbeAirFlowProtocolTypemandatory Air flow protocol type	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.17.1.59
sensorProbeAirFlowSensitivitymandatory Air flow (AFS00) sensitivity	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.17.1.60
sensorProbeAirFlowNormalStatemandatory Air flow (AFS00) normal state	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.61
sensorProbeAirFlowCalibratemandatory Air flow (AFS00) normal state	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.17.1.62

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeSwitchEntry row .1.3.6.1.4.1.3854.1.2.2.1.18.1

This is an entry in the sensorProbeSwitchEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeSwitchDescriptionmandatory A Description of this sensor Switch	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.1
sensorProbeSwitchLocationmandatory The physical location of this sensor Switch	RFC1213-MIBDisplayStringr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.2
sensorProbeSwitchStatusmandatory The current status of this Sensor, only input switches have a status	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.18.1.3
sensorProbeSwitchOnlinemandatory If this Sensor is currently online	Enumeration Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.4
sensorProbeSwitchGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.5
sensorProbeSwitchDirectionmandatory To set a switch to input enter 0. To set a switch to output enter 1	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.6
sensorProbeSwitchNormalStatemandatory The normal state of an input switch. If an input switch is in this state it is normal, else it is critical. An open switch senses +5 volts. A closed switch senses 0 volts.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.7
sensorProbeSwitchOutputLevelmandatory An output swith can be set to this level	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.8
sensorProbeSensorTypemandatory Enter the type of this Sensor	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.9
sensorProbeSwitchEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.11
sensorProbeSwitchEmailTrapSchedulemandatory SP Only: Email/trap limit schedule for this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.12
sensorProbeSwitchEmailTrapIntervalmandatory Minimum time between each [email/trap:SP, only trap:CP8] (can be from 0 to 60 minutes)	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.13
sensorProbeSwitchSendNormalTrapmandatory Enable sending email/trap when sensor goes to normal	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.18.1.14
sensorProbeSwitchDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.15
sensorProbeSwitchDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.16
sensorProbeSwitchIndexmandatory The index into the Switch sensor table	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.18.1.17
sensorProbeSwitchRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.18
sensorProbeSwitchRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.19
sensorProbeSwitchRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.20
sensorProbeSwitchRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.21
sensorProbeSwitchEmailIntervalmandatory CP8 Only: Minimum time between each email (can be from 0 to 60 minutes)	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.22
sensorProbeSwitchRelayOutputVoltStatusmandatory SP Only: The current voltage status of the relay	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.18.1.23
sensorProbeSwitchManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.24
sensorProbeSwitchManualRelayActionmandatory Control the relay manualy	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.25
sensorProbeSwitchRelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.26
sensorProbeSwitchRelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.27
sensorProbeSwitchIndexCountmandatory Number of Switch sensor online	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.18.1.28
sensorProbeSwitchSirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.29
sensorProbeSwitchSirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.30
sensorProbeSwitchSirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.18.1.31
sensorProbeSwitchSirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.32
sensorProbeSwitchAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.33
sensorProbeSwitchSirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.34
sensorProbeSwitchURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.35
sensorProbeSwitchOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.36
sensorProbeSwitchContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.37
sensorProbeSwitchContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.39
sensorProbeSwitchCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w Constraints: range: 1-255	.1.3.6.1.4.1.3854.1.2.2.1.18.1.43
sensorProbeSwitchRelayControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.44
sensorProbeSwitchSirenControlModemandatory Siren Control Mode used for selecting the mode to control a siren.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.45
sensorProbeSwitchSendNormalMailmandatory Enable sending email when sensor goes to normal	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.46
sensorProbeSwitchSendTrapmandatory Enable sending trap when sensor change status	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.47
sensorProbeSwitchSendMailmandatory Enable sending email when sensor change status	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.48
sensorProbeSwitchWaterRopeLeakLocationmandatory Location of leakage of water rope sensor.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.18.1.49
sensorProbeSwitchWaterRopeLengthmandatory Length of water rope sensor.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.18.1.50
sensorProbeSwitchWaterRopeUnitmandatory Display unit of water rope sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.51
sensorProbeSwitchWaterRopeImpedancemandatory Sensing wire impedance per meter value times 100	Integer32r/w Constraints: range: 0-67	.1.3.6.1.4.1.3854.1.2.2.1.18.1.52
sensorProbeSwitchWaterRopeRawmandatory Raw value of location or length in ohms	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.18.1.53
sensorProbeSwitchWaterRopeTypemandatory Water rope sensing cable type	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.18.1.55

This table contains the data for every RMS current Sensor in the SensorArray. Each row in the table contains data for a different RMS current Sensor.

sensorProbeIRMSSensorEntry row .1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1

This is an entry in the sensorProbeIRMSSensorEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeIRMSSensorIndexmandatory A unique value for each IRMS sensor port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.1
sensorProbeIRMSDescriptionmandatory A Description of this sensor IRMS	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.2
sensorProbeIRMSPercentmandatory The relative IRMS percentage measured by this sensor	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.3
sensorProbeIRMSStatusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.4
sensorProbeIRMSOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.5
sensorProbeIRMSGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.6
sensorProbeIRMSHighWarningmandatory How high the relative IRMS this sensor measures before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.7
sensorProbeIRMSHighCriticalmandatory How high the relative IRMS this sensor measures before it becomes critical	Integer32r/w Constraints: range: 0-65534	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.8
sensorProbeIRMSLowWarningmandatory How low the relative IRMS this sensor measures before it sends a warning	Integer32r/w Constraints: range: 0-65534	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.9
sensorProbeIRMSLowCriticalmandatory How low the relative IRMS this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.10
sensorProbeIRMSRearmmandatory The percent relative IRMS to rearm the status. For example if status goes from normal to warning, the IRMS must go down spAnalogueRearm below warning before the status goes to normal	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.11
sensorProbeIRMSRawmandatory The unformatted, raw, A/D value in this sensor. Contains more resolution than the formated percentage. This number can go from 0 to 1023 depending on the input voltage	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.13
sensorProbeIRMSEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.17
sensorProbeIRMSDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.21
sensorProbeIRMSDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.22
sensorProbeIRMSRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.29
sensorProbeIRMSRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.30
sensorProbeIRMSRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.31
sensorProbeIRMSRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.32
sensorProbeIRMSSirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.37
sensorProbeIRMSSirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.38
sensorProbeIRMSSirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.39
sensorProbeIRMSSirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.40
sensorProbeIRMSAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w Constraints: range: 0-67	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.41
sensorProbeIRMSSirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.42
sensorProbeIRMSURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.43
sensorProbeIRMSOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.44
sensorProbeIRMSDatacollectTypemandatory Type of datacollect to collect.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.45
sensorProbeIRMSContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.46
sensorProbeIRMSContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w Constraints: range: 0-65534	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.47
sensorProbeIRMSContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.48
sensorProbeIRMSContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.49
sensorProbeIRMSContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.50
sensorProbeIRMSContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.51
sensorProbeIRMSCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.26.2.1.52

This table contains the data for every RMS voltage Sensor in the SensorArray. Each row in the table contains data for a different RMS voltage Sensor.

sensorProbeVRMSSensorEntry row .1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1

This is an entry in the sensorProbeVRMSSensorEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeVRMSSensorIndexmandatory A unique value for each VRMS sensor port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.1
sensorProbeVRMSDescriptionmandatory A Description of this sensor VRMS	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.2
sensorProbeVRMSPercentmandatory The relative VRMS percentage measured by this sensor	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.3
sensorProbeVRMSStatusmandatory The current status of this Sensor	Enumeration Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.4
sensorProbeVRMSOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.5
sensorProbeVRMSGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w Constraints: range: -32768-32767	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.6
sensorProbeVRMSHighWarningmandatory How high the relative VRMS this sensor measures before it sends a warning	Integer32r/w Constraints: range: 1-1	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.7
sensorProbeVRMSHighCriticalmandatory How high the relative VRMS this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.8
sensorProbeVRMSLowWarningmandatory How low the relative VRMS this sensor measures before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.9
sensorProbeVRMSLowCriticalmandatory How low the relative VRMS this sensor measures before it becomes critical	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.10
sensorProbeVRMSRearmmandatory The percent relative VRMS to rearm the status. For example if status goes from normal to warning, the VRMS must go down spAnalogueRearm below warning before the status goes to normal	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.11
sensorProbeVRMSRawmandatory The unformatted, raw, A/D value in this sensor. Contains more resolution than the formated percentage. This number can go from 0 to 1023 depending on the input voltage	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.13
sensorProbeVRMSEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.17
sensorProbeVRMSDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.21
sensorProbeVRMSDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.22
sensorProbeVRMSRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.29
sensorProbeVRMSRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.30
sensorProbeVRMSRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.31
sensorProbeVRMSRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.32
sensorProbeVRMSSirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.37
sensorProbeVRMSSirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.38
sensorProbeVRMSSirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.39
sensorProbeVRMSSirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.40
sensorProbeVRMSAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.41
sensorProbeVRMSSirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.42
sensorProbeVRMSvoltageModemandatory VRMS Voltage Mode.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.43
sensorProbeVRMSURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.44
sensorProbeVRMSOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.45
sensorProbeVRMSDatacollectTypemandatory Type of datacollect to collect.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.46
sensorProbeVRMSContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.47
sensorProbeVRMSContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.48
sensorProbeVRMSContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.49
sensorProbeVRMSContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.50
sensorProbeVRMSContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.51
sensorProbeVRMSContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.52
sensorProbeVRMSCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.27.2.1.53

This table contains the data for every Energy Sensor in the SensorArray. Each row in the table contains data for a different Energy Sensor.

sensorProbeEnergySensorEntry row .1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1

This is an entry in the sensorProbeEnergySensorEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeEnergySensorIndexmandatory A unique value for each Energy sensor port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.1
sensorProbeEnergyDescriptionmandatory A Description of this sensor Energy	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.2
sensorProbeEnergyPercentmandatory The relative Energy percentage measured by this sensor	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.3
sensorProbeEnergyStatusmandatory The current status of this Sensor	Enumeration Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.4
sensorProbeEnergyOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.5
sensorProbeEnergyGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.6
sensorProbeEnergyHighWarningmandatory How high the relative Energy this sensor measures before it sends a warning	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.7
sensorProbeEnergyHighCriticalmandatory How high the relative Energy this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.8
sensorProbeEnergyLowWarningmandatory How low the relative Energy this sensor measures before it sends a warning	Integer32r/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.9
sensorProbeEnergyLowCriticalmandatory How low the relative Energy this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.10
sensorProbeEnergyRearmmandatory The percent relative Energy to rearm the status. For example if status goes from normal to warning, the Energy must go down spAnalogueRearm below warning before the status goes to normal	Integer32r/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.11
sensorProbeEnergyRawmandatory The unformatted, raw, A/D value in this sensor. Contains more resolution than the formated percentage. This number can go from 0 to 1023 depending on the input voltage	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.13
sensorProbeEnergyEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.17
sensorProbeEnergyDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.21
sensorProbeEnergyDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.22
sensorProbeEnergyRelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.29
sensorProbeEnergyRelayOnPortmandatory The sensor port that the relay will listen to. If this is set to 255, then the relay will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.30
sensorProbeEnergyRelayActiveStatusmandatory Sensor status that will activate the relay	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.31
sensorProbeEnergyRelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.32
sensorProbeEnergySirenCycleTimemandatory Siren toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.37
sensorProbeEnergySirenOnPortmandatory The sensor port that the siren will listen to. If this is set to 255, then the siren will not listen to any sensor ports	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.38
sensorProbeEnergySirenActiveStatusmandatory Sensor status that will activate the siren	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.39
sensorProbeEnergySirenActionmandatory What the siren will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.40
sensorProbeEnergyAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.41
sensorProbeEnergySirenDelayAlarmmandatory Siren delay in seconds before start Alarm.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.42
sensorProbeEnergyReadingModemandatory Energy Meter Reading Mode.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.43
sensorProbeEnergyURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.44
sensorProbeEnergyOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.45
sensorProbeEnergyDatacollectTypemandatory Type of datacollect to collect.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.46
sensorProbeEnergyContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.47
sensorProbeEnergyContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.48
sensorProbeEnergyContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.49
sensorProbeEnergyContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.50
sensorProbeEnergyContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.51
sensorProbeEnergyContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.52
sensorProbeEnergyCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.28.2.1.53

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort1Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1

This is an entry in the sensorProbeRelayArrayPort1 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort1Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.1
sensorProbeRelayArrayPort1Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.2
sensorProbeRelayArrayPort1Statusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.4
sensorProbeRelayArrayPort1Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.5
sensorProbeRelayArrayPort1GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.6
sensorProbeRelayArrayPort1NormalStatemandatory The normal state of RelayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.7
sensorProbeRelayArrayPort1RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.18
sensorProbeRelayArrayPort1RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.21
sensorProbeRelayArrayPort1ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.24
sensorProbeRelayArrayPort1ManualRelayActionmandatory Control the relay manualy	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.25
sensorProbeRelayArrayPort1RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.26
sensorProbeRelayArrayPort1RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.27
sensorProbeRelayArrayPort1URLmandatory Sersor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.28
sensorProbeRelayArrayPort1OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.29
sensorProbeRelayArrayPort1ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.1.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort2Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1

This is an entry in the sensorProbeRelayArrayPort2 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort2Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.1
sensorProbeRelayArrayPort2Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.2
sensorProbeRelayArrayPort2Statusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.4
sensorProbeRelayArrayPort2Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.5
sensorProbeRelayArrayPort2GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.6
sensorProbeRelayArrayPort2NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.7
sensorProbeRelayArrayPort2RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.18
sensorProbeRelayArrayPort2RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.21
sensorProbeRelayArrayPort2ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.24
sensorProbeRelayArrayPort2ManualRelayActionmandatory Control the relay manualy	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.25
sensorProbeRelayArrayPort2RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.26
sensorProbeRelayArrayPort2RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.27
sensorProbeRelayArrayPort2URLmandatory Sensor URL link	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.28
sensorProbeRelayArrayPort2OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.29
sensorProbeRelayArrayPort2ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.2.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort3Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1

This is an entry in the sensorProbeRelayArrayPort3 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort3Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.1
sensorProbeRelayArrayPort3Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.2
sensorProbeRelayArrayPort3Statusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.4
sensorProbeRelayArrayPort3Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.5
sensorProbeRelayArrayPort3GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.6
sensorProbeRelayArrayPort3NormalStatemandatory The normal state of RleayArray	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.7
sensorProbeRelayArrayPort3RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.18
sensorProbeRelayArrayPort3RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.21
sensorProbeRelayArrayPort3ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.24
sensorProbeRelayArrayPort3ManualRelayActionmandatory Control the relay manualy	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.25
sensorProbeRelayArrayPort3RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.26
sensorProbeRelayArrayPort3RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.27
sensorProbeRelayArrayPort3URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.28
sensorProbeRelayArrayPort3OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.29
sensorProbeRelayArrayPort3ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.3.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort4Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1

This is an entry in the sensorProbeRelayArrayPort4 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort4Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.1
sensorProbeRelayArrayPort4Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.2
sensorProbeRelayArrayPort4Statusmandatory The current status of this Sensor	Enumeration Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.4
sensorProbeRelayArrayPort4Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.5
sensorProbeRelayArrayPort4GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.6
sensorProbeRelayArrayPort4NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.7
sensorProbeRelayArrayPort4RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.18
sensorProbeRelayArrayPort4RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.21
sensorProbeRelayArrayPort4ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.24
sensorProbeRelayArrayPort4ManualRelayActionmandatory Control the relay manualy	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.25
sensorProbeRelayArrayPort4RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.26
sensorProbeRelayArrayPort4RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.27
sensorProbeRelayArrayPort4URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.28
sensorProbeRelayArrayPort4OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.29
sensorProbeRelayArrayPort4ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.29.4.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort5Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1

This is an entry in the sensorProbeRelayArrayPort5 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort5Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.1
sensorProbeRelayArrayPort5Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.2
sensorProbeRelayArrayPort5Statusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.4
sensorProbeRelayArrayPort5Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.5
sensorProbeRelayArrayPort5GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.6
sensorProbeRelayArrayPort5NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.7
sensorProbeRelayArrayPort5RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.18
sensorProbeRelayArrayPort5RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.21
sensorProbeRelayArrayPort5ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.24
sensorProbeRelayArrayPort5ManualRelayActionmandatory Control the relay manualy	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.25
sensorProbeRelayArrayPort5RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.26
sensorProbeRelayArrayPort5RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.27
sensorProbeRelayArrayPort5URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.28
sensorProbeRelayArrayPort5OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.29
sensorProbeRelayArrayPort5ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.5.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort6Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1

This is an entry in the sensorProbeRelayArrayPort6 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort6Indexmandatory A unique value for each sensor RelayArray port.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.1
sensorProbeRelayArrayPort6Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.2
sensorProbeRelayArrayPort6Statusmandatory The current status of this Sensor	Enumeration Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.4
sensorProbeRelayArrayPort6Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.5
sensorProbeRelayArrayPort6GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.6
sensorProbeRelayArrayPort6NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.7
sensorProbeRelayArrayPort6RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.18
sensorProbeRelayArrayPort6RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.21
sensorProbeRelayArrayPort6ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.24
sensorProbeRelayArrayPort6ManualRelayActionmandatory Control the relay manualy	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.25
sensorProbeRelayArrayPort6RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.26
sensorProbeRelayArrayPort6RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.27
sensorProbeRelayArrayPort6URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.28
sensorProbeRelayArrayPort6OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.29
sensorProbeRelayArrayPort6ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.6.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort7Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1

This is an entry in the sensorProbeRelayArrayPort7 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort7Indexmandatory A unique value for each sensor RelayArray port.	Integer32 Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.1
sensorProbeRelayArrayPort7Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.2
sensorProbeRelayArrayPort7Statusmandatory The current status of this Sensor	Enumeration Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.4
sensorProbeRelayArrayPort7Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.5
sensorProbeRelayArrayPort7GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.6
sensorProbeRelayArrayPort7NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.7
sensorProbeRelayArrayPort7RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.18
sensorProbeRelayArrayPort7RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.21
sensorProbeRelayArrayPort7ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.24
sensorProbeRelayArrayPort7ManualRelayActionmandatory Control the relay manualy	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.25
sensorProbeRelayArrayPort7RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.26
sensorProbeRelayArrayPort7RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.27
sensorProbeRelayArrayPort7URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.28
sensorProbeRelayArrayPort7OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.29
sensorProbeRelayArrayPort7ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.7.2.1.30

This table contains the data for every Switch Sensor in the SensorArray. Each row in the table contains data for a different Switch Sensor.

sensorProbeRelayArrayPort8Entry row .1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1

This is an entry in the sensorProbeRelayArrayPort8 Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeRelayArrayPort8Indexmandatory A unique value for each sensor RelayArray port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.1
sensorProbeRelayArrayPort8Descriptionmandatory A Description of this sensor RelayArray	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.2
sensorProbeRelayArrayPort8Statusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.4
sensorProbeRelayArrayPort8Onlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.5
sensorProbeRelayArrayPort8GoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.6
sensorProbeRelayArrayPort8NormalStatemandatory The normal state of RleayArray	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.7
sensorProbeRelayArrayPort8RelayCycleTimemandatory Relay toggle period in seconds for Cycle action.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.18
sensorProbeRelayArrayPort8RelayActionmandatory What the relay will do when the listened to port status turns to the specified active status.	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.21
sensorProbeRelayArrayPort8ManualRelayCycleTimemandatory Relay toggle period in seconds for Manual Cycle action.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.24
sensorProbeRelayArrayPort8ManualRelayActionmandatory Control the relay manualy	Enumerationr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.25
sensorProbeRelayArrayPort8RelayDescOnmandatory Description of relay On	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.26
sensorProbeRelayArrayPort8RelayDescOffmandatory Description of relay Off	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.27
sensorProbeRelayArrayPort8URLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-65535	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.28
sensorProbeRelayArrayPort8OpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.29
sensorProbeRelayArrayPort8ControlModemandatory Relay Control Mode used for selecting the mode to control a relay.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.29.8.2.1.30

This table contains the data for every VirtualAnalog Sensor in the SensorArray. Each row in the table contains data for a different VirtualAnalog Sensor.

sensorProbeVirtualAnalogSensorEntry row .1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1

This is an entry in the sensorProbeVirtualAnalogSensorEntry Table

Indexes

No indexes recorded

Column	Syntax	OID
sensorProbeVirtualAnalogSensorIndexmandatory A unique value for each VirtualAnalog sensor port.	Integer32	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.1
sensorProbeVirtualAnalogDescriptionmandatory A Description of this sensor	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.2
sensorProbeVirtualAnalogStatusmandatory The current status of this Sensor	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.4
sensorProbeVirtualAnalogOnlinemandatory If this Sensor is currently online	Enumeration	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.5
sensorProbeVirtualAnalogGoOnlinemandatory To put online enter a 1, to take offline enter a 2	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.6
sensorProbeVirtualAnalogHighWarningmandatory How high the relative VirtualAnalog this sensor measures before it sends a warning	Integer32r/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.7
sensorProbeVirtualAnalogHighCriticalmandatory How high the relative VirtualAnalog this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.8
sensorProbeVirtualAnalogLowWarningmandatory How low the relative VirtualAnalog this sensor measures before it sends a warning	Integer32r/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.9
sensorProbeVirtualAnalogLowCriticalmandatory How low the relative VirtualAnalog this sensor measures before it becomes critical	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.10
sensorProbeVirtualAnalogRearmmandatory The percent relative VirtualAnalog to rearm the status. For example if status goes from normal to warning, the VirtualAnalog must go down spAnalogueRearm below warning before the status goes to normal	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.11
sensorProbeVirtualAnalogRawmandatory The unformatted, raw, A/D value in this sensor. Contains more resolution than the formated percentage. This number can go from 0 to 1023 depending on the input voltage	Integer32 Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.13
sensorProbeVirtualAnalogEmailTrapLimitmandatory Enable email/trap limit feature	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.17
sensorProbeVirtualAnalogDelayErrormandatory Time in seconds after the sensor has been in error status before report as an error	Integer32r/w Constraints: range: -40-167	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.21
sensorProbeVirtualAnalogDelayNormalmandatory Time in seconds after the sensor change from error to normal before report as normal	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.22
sensorProbeVirtualAnalogUnitmandatory Display unit in VirtualAnalog.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.27
sensorProbeVirtualAnalogAcknowledgementmandatory Acknowledged sensor error and stop notification	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.41
sensorProbeVirtualAnalogURLmandatory Sensor URL link.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.43
sensorProbeVirtualAnalogOpenURLmandatory Open URL in this browser or open in a new window.	Enumerationr/w Constraints: range: 0-7	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.44
sensorProbeVirtualAnalogContTimeHighCriticalmandatory Continuous time for this sensor to be in High Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.45
sensorProbeVirtualAnalogContTimeHighWarningmandatory Continuous time for this sensor to be in High Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.46
sensorProbeVirtualAnalogContTimeNormalmandatory Continuous time for this sensor to be in Normal before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.47
sensorProbeVirtualAnalogContTimeLowWarningmandatory Continuous time for this sensor to be in Low Warning before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.48
sensorProbeVirtualAnalogContTimeLowCriticalmandatory Continuous time for this sensor to be in Low Critical before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.49
sensorProbeVirtualAnalogContTimeSensorErrormandatory Continuous time for this sensor to be in Sensor Error before accepting new Status.	Integer32r/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.50
sensorProbeVirtualAnalogCalendarmandatory Enable or disable the calendar filtering working hours of sensor.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.51
sensorProbeVirtualAnalogValueFactormandatory To change the ratio of value.	Enumerationr/w	.1.3.6.1.4.1.3854.1.2.2.1.19.30.2.1.52