SCTE-HMS-QAM-MIB Table View

This table describes the configuration and attributes of each
QAM channel of the QAM designated by ifIndex.

qamChannelEntry row .1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1

There is an entry in the table for each QAM channel. The index
to this table is the ifIndex of each QAM channel.

Indexes

IF-MIBifIndex

Column	Syntax	OID
qamChannelFrequency The center frequency of the QAM channel.	HertzSNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.1
qamChannelModulationFormat RF Modululation for this output QAM channel when qamChannelContWaveMode is off.	SCTE-HMS-HEADENDIDENT-TC-MIBQAMChannelModulationFormat Type Values: 1 unknown 2 other 3 qam64 4 qam256 5 qam128 6 qam512 7 qam1024	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.2
qamChannelInterleaverLevel The interleaver level for FEC coding. level1 - implies interleaver level 1 level2 - implies interleaver level 2 This object is only valid when AnnexMode has the value annexB.	Enumeration Enumerated Values: 1 level1 2 level2	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.3
qamChannelInterleaverMode The interleaving depth or operation mode of the interleaver. 'taps8Increment16': protection 5.9/4.1 usec, latency .22/.15 msec 'taps16Increment8': protection 12/8.2 usec, …	SCTE-HMS-HEADENDIDENT-TC-MIBQAMChannelInterleaveMode Type Values: 1 unknown 2 other 3 fecI8J16 4 fecI16J8 5 fecI32J4 6 fecI64J2 7 fecI128J1 8 fecI12J17 9 fecI128J2 10 fecI128J3 11 fecI128J4 12 fecI128J5 13 fecI128J6 14 fecI128J7 15 fecI128J8	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.4
qamChannelPower The output power of the QAM channel. If the QAM channel is muted, value is not valid.	0.1 dBmVSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.5
qamChannelSquelch Indicates whether the QAM port is muted or not.	Enumeration Enumerated Values: 1 unmuted 2 muted	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.6
qamChannelContWaveMode Indicates whether Continuous Wave mode is enabled or not for output.	Enumeration Enumerated Values: 1 cwmOff 2 cwmOn	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.7
qamChannelAnnexMode Specifies the ITU-T standard supported by the QAM channel annexA - standard specified by Annex A of ITU-T J.83 annexB - standard specified by Annex B of ITU-T J.83 annexC - standard specified by Annex C o…	Enumeration Enumerated Values: 1 unknown 2 other 3 annexA 4 annexB 5 annexC	.1.3.6.1.4.1.5591.1.11.5.3.1.1.1.1.8

This table decribes MPEG and DOCSIS characteristics that are
not part of the DOCSIS-IF-MIB.

qamChannelCommonEntry row .1.3.6.1.4.1.5591.1.11.5.3.1.1.2.1

Each entry of this table describes attributes of an RF channel
for both MPEG and DOCSIS QAMs.

Indexes

IF-MIBifIndex

Column	Syntax	OID
qamChannelCommonOutputBw The QAM channel output bandwidth or capacity.	bpsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5591.1.11.5.3.1.1.2.1.1
qamChannelCommonUtilization The utilization of the QAM channel in 0.1 percentage. This rate may be calculated as transport stream packets / ( transport stream packets + null packets ). If not applicable, a value of -1 is returned.	0.1 PercentInteger32 Constraints: range: -1-1000	.1.3.6.1.4.1.5591.1.11.5.3.1.1.2.1.2

This table is designed to show the IP addresses configuration
for the QAM channels, optionally UDP port range, Program Number
range associated with QAM channels. Configuring these parameters
is necessary when performing session-based provisioning. A  
session-based provisioning request must conform to the
configurations in this table. The QAM channels within an QAM 
device may be partitioned to support multiple UDP, QAM or
ProgramNo ranges. Though it's helpful to partition the QAM
channels when the total number of QAM channel increases, this is
not a must. This table may also be used to show the reserved UDP
ports, or program numbers for special purposes instead of using
default ones allowed by hardware, software, or MPEG protocol.

qamConfigEntry row .1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1

Each entry corresponds to the configuration of a QAM channel
range.

Indexes

ENTITY-MIBentPhysicalIndex qamConfigIndex

Column	Syntax	OID
qamConfigIndex The table index.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.1
qamConfigQamChannelIdMin QAMChannelId maybe within a line card or global depending on entPhysicalIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.2
qamConfigQamChannelIdMax QAMChannelId maybe within a line card or global depending on entPhysicalIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.3
qamConfigIPAddrType The type of the program destination address as defined by inetAddressType. The default value is 1 for ipv4(1)	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.4
qamConfigIPAddr IP address of the QAM channel.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.5
qamConfigUdpPortRangeMin The lowest UDP port of the UDP port range that can be used on this QAM channel.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.6
qamConfigUdpPortRangeMax The highest UDP port of the UDP port range that can be used on this QAM channel.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.7
qamConfigOutputProgNoMin The lowest MPEG output program number that can be used on the QAM channel.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.8
qamConfigOutputProgNoMax The highest MPEG output program number that can be used on the QAM channel.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.5591.1.11.5.3.1.1.3.1.9