RDN-CMTS-MIB Table View

This table describes the attributes of downstream 
channel in addition to those specified by the docsIfMib.

rdnCmtsDownstreamChannelEntry row .1.3.6.1.4.1.4981.2.1.1.1

An entry provides a list of attributes for a single
Downstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableDownstream(128).

Indexes

IF-MIBifIndex

Column	Syntax	OID
rdnCmtsDSModulation The attribute to control the down stream modulation. When this object is set to FALSE(2), the downstream transmitter will output a CW, or tonal signal at the tuned RF frequency.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4981.2.1.1.1.1

This table describes the attributes of upstream 
channel in addition to those specified by the docsIfMib.

rdnCmtsUpstreamChannelEntry row .1.3.6.1.4.1.4981.2.1.2.1

List of attributes for a single upstream channel.
An entry in this table exists for each ifEntry with an
ifType of docsCableUpstreamInterface (129) for DOCSIS1.x
CMTSs, and ifType of docsCableUpstreamChannel (205) for
…

Indexes

IF-MIBifIndex

Column	Syntax	OID
rdnCmtsUSNominalRxPower The attribute to program the target, or nominal, receive power of each upstream RF port. The range is channel width dependent: Power Level Channel Width -160,+140 200 kHz -130,+170 400 k…	Integer32r/w Constraints: range: -160-290	.1.3.6.1.4.1.4981.2.1.2.1.1
rdnCmtsUSNominalRxPowerMode This object describes the setting mode for rdnCmtsUSNomialRxPower. The default setting is the absolute mode.	Enumerationr/w Enumerated Values: 0 default 1 absolute	.1.3.6.1.4.1.4981.2.1.2.1.2
rdnCmtsUSInvitedRangingInterval To fix Invited(Periodic) Ranging Intervals as in input to the Bandwidth Allocator algorithm.	Integer32r/w Constraints: range: 0-30000	.1.3.6.1.4.1.4981.2.1.2.1.3
rdnCmtsUSRangingResponseControl The attribute to force all RNG-Resp messages to issue a 'Continue' Ranging Status indefinitely regardless of timing, power, etc. accuracy of previous incoming Ranging Request. Value 0 means Normal Ranging Mode, value 1…	Enumerationr/w Enumerated Values: 0 normal 1 override	.1.3.6.1.4.1.4981.2.1.2.1.4
rdnCmtsUSRangingPowerOverride The attribute overrides upstream power adjustments performed by the CMTS to CM's. When this object is set to TRUE(1), the override is activated, all Ranging Response message will be transmitted with ZERO power adjust…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4981.2.1.2.1.5
rdnCmtsUSTotalModemCount When read, this object returns the total number of Cable Modems per upstream.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4981.2.1.2.1.6
rdnCmtsUSRegisteredModemCount When read, this object returns the number of registered Cable Modems per upstream.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4981.2.1.2.1.7
rdnCmtsUSUnregisteredModemCount When read, this object returns the number of unregistered Cable Modems per upstream. This count reflects modems that are in the process of attempting to join the network. Note that this does not include offline mod…	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4981.2.1.2.1.8
rdnCmtsUSOfflineModemCount When read, this object returns the number of offline Cable Modems per upstream.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.4981.2.1.2.1.9

This table has the object to enable or disable the generation of
proprietary CMTS LinkUp and Link Down traps

rdnCmtsLinkUpDownTrapEnableEntry row .1.3.6.1.4.1.4981.2.1.4.1

An entry in this table exists for each ifEntry with an
ifType of docsCableUpstream(129) or docsCableUpstreamChannel(205).

Indexes

IF-MIBifIndex

Column	Syntax	OID
rdnCmtsLinkUpDownTrapEnable Indicates whether rdnCmtsUpstreamIfLinkUpTrap and rdnCmtsUpstreamIfLinkDownTrap traps should be generated for this interface. By default, this object has the value disabled(2). These traps are convenient for knowing…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.4981.2.1.4.1.1

This table describes the mapping between CPE's MAC address
and MAC address of the cable modem these CPEs are attached to.
This table does not support the walk/getNext. It is not intended
to use this mib to walk the list of cpe's in the system.

rdnCmtsCpeToCmEntry row .1.3.6.1.4.1.4981.2.2.7.1.1

An entry describes the mapping between one CPE's MAC address
and MAC address of the cable modem this CPE is attached to.

Indexes

rdnCmtsCpeMac

Column	Syntax	OID
rdnCmtsCpeMac This object is the MAC address of the CPE (host) that a cable modem is attached to.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.7.1.1.1
rdnCmtsCmMac This object returns the MAC address of the cable modem that a CPE (host) is attached to. If the CPE is not found being attached to any cable modem registered on this CMTS, the read of this object will return zero.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.7.1.1.2

This table is an extension of the docsIfCmtsCmStatusTable. 
It provides additional information about the CM.

rdnIfCmtsCmStatusEntry row .1.3.6.1.4.1.4981.2.2.8.1

Each entry of the table rdnIfCmtsCmStatusTable.
Each entry provides some additional information about the CM.

Indexes

No indexes recorded

Column	Syntax	OID
rdnIfCmtsCmStatusRegistrationTime When read, this object will return the time in seconds since the modem registered. If the modem is unregistered, it will return ZERO	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.8.1.1
rdnIfCmtsCmStatusTxUnicastKbytes When read, this object will return the number of unicast KBytes (1024 bytes) the CMTS has transmitted to the modem (Downstream direction). For offline modems this value is the total number of unicast KBytes when it w…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.8.1.2
rdnIfCmtsCmStatusRxUnicastKbytes When read, this object will return the number of unicast KBytes (1024 bytes) the CMTS has received from the modem (Upstream direction). For offline modems this value is the total number of unicast KBytes when it was on…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.8.1.3
rdnIfCmtsCmStatusTxUnicastExtKbytes When read, this object will return the number of unicast KBytes (1024 bytes) the CMTS has transmitted to the modem (Downstream direction). For offline modems this value is the the total number of unicast KBytes when i…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.8.1.4
rdnIfCmtsCmStatusRxUnicastExtKbytes When read, this object will return the number of unicast KBytes (1024 bytes) the CMTS has received from the modem (Upstream Direction). For offline modems this value is the the total number of unicast KBytes when it w…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.8.1.5
rdnIfCmtsCmStatusSpectrumGroupName When read, this object will return the spectrum group name. If data not available, return NULL string	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4981.2.2.8.1.6
rdnIfCmtsCmStatusUpstreamPort The Upstream Port Number the modem is using. For offline modems this value is meaningless.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.4981.2.2.8.1.7
rdnIfCmtsCmStatusDownStreamPort The downstream port number the modem is using, For offline modems this value is meaningless.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.4981.2.2.8.1.8
rdnIfCmtsCmStatusValue Current Cable Modem connectivity state. Returned status information is the CM status as assumed by the CMTS, and indicates the following events: init-o(1) Option file transfer was started. init-t(2) …	Enumeration Enumerated Values: 1 init-o 2 init-t 3 init-r1 4 init-r2 5 init-rc 6 dhcp-d 7 dhcp-o 8 dhcp-req 9 dhcp-ack 10 online 11 online-d 12 online-un 13 online-pk 14 online-pt 15 reject-m 16 reject-c 17 reject-r 18 reject-pk 19 reject-pt 20 offline	.1.3.6.1.4.1.4981.2.2.8.1.9
rdnIfCmtsCmStatusDSBondingGroupId The downstream channel bonding group ID of primary service flow. This value is zero if not registered for channel bonding.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4981.2.2.8.1.10
rdnIfCmtsCmStatusOnlineTimes Number of times a modem has gone from offline to online since the modem was first seen ranging.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.8.1.11
rdnIfCmtsCmStatusPercentOnline A percentage of time the modem has been in an online state since the modem was first seen ranging. This value is displayed as (percent value x 100) in order to show precision. i.e. 99.34% will be displayed as 9934.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.4981.2.2.8.1.12
rdnIfCmtsCmStatusMinOnlineTime Shortest period of time this modem has been online since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.13
rdnIfCmtsCmStatusAvgOnlineTime Average period of time this modem has been online since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.14
rdnIfCmtsCmStatusMaxOnlineTime Longest period of time this modem has been online since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.15
rdnIfCmtsCmStatusMinOfflineTime Shortest period of time this modem has been offline since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.16
rdnIfCmtsCmStatusAvgOfflineTime Average period of time this modem has been offline since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.17
rdnIfCmtsCmStatusMaxOfflineTime Longest period of time this modem has been offline since the modem was first seen ranging.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.4.1.4981.2.2.8.1.18

This table provides the information about the CPEs attached to the
CM.

rdnCmToCpeEntry row .1.3.6.1.4.1.4981.2.2.12.1

An entry of the table rdnCmToCpeTable. Each entry provides the
CPE Mac and IP addresses.

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex rdnCmToCpeIndex

Column	Syntax	OID
rdnCmToCpeIndex Index Value for an individual CPE, This index value is not guaranteed to remain same during CMTS uptime.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4981.2.2.12.1.1
rdnCmToCpeMacAddress The Mac Address of the CPE attached to the CM	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.12.1.2
rdnCmToCpeIpAddress The IP Address of the CPE attached to the CM	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.4981.2.2.12.1.3
rdnCmToCpeIPv6Addr This attribute represents the IPv6 address of the CPE. If the CPE has no IPv6 address assigned, or the Internet address is unknown, the value of this attribute is the all zeros address.	INET-ADDRESS-MIBInetAddressIPv6 Type Constraints: range: 16	.1.3.6.1.4.1.4981.2.2.12.1.4

The Remote Query feature allows the BSR to act as an SNMP Manager,
periodically collecting statistics from cable modems, using SNMP 
get/next requests.  The rdnRQueryCmtsCmStatusTable displays the
collected statistics.
          
Remote Query polling is enabled and configured using the BSR's
command line interface.   The frequency of polling should be
selected with care, so as not to introduce excessive
overhead that would degrade performance.

rdnRQueryCmtsCmStatusEntry row .1.3.6.1.4.1.4981.2.2.15.1

An entry in the rdnRQueryCmtsCmStatusTable. Each entry
represents a set physical-layer status values for a
specific cable modem. The table is indexed by a DOCSIS
cable modem index value (docsIfCmtsCmStatusIndex).

Indexes

DOCS-IF-MIBdocsIfCmtsCmStatusIndex

Column	Syntax	OID
rdnRQueryCmtsCmDownChannelPower The last polled value of the CM's docsIfdownChannelPower MIB object, the received downstream power level at the CM, in TenthdbMv. DOCSIS specifies this to be between +5.0 and - 15.0 dBmv.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4981.2.2.15.1.1
rdnRQueryCmStatusTxPower The last polled value of the CM's docsIfCmStatusTxPower MIB object, the CMs upstream transmit power level, in TenthdBmv. DOCSIS specifies this to be between 8.0 and 54.0 dbMv.	DOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4981.2.2.15.1.2
rdnRQueryUpChannelTxTimingOffset The last polled value of the CM's docsIfUpChannelTxTimingOffset MIB object. This is the CM's estimate of the current round trip time obtained from the ranging offset (initial ranging offset + ranging offset adjustmen…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.15.1.3
rdnRQuerySigQSignalNoise The last polled value of the CM's docsIfSigQSignalNoise MIB object, the downstream signal to noise ratio in TenthdB.	dBDOCS-IF-MIBTenthdB	.1.3.6.1.4.1.4981.2.2.15.1.4
rdnRQuerySigQMicroreflections The last polled value of the CM's docsIfSigQMicroreflections MIB object, which is its estimate of the total microreflections including in-channel responses perceived on the upstream interface, measured in dBc below th…	dBcInteger32 Constraints: range: 0-255	.1.3.6.1.4.1.4981.2.2.15.1.5
rdnRQueryPollTime The value of sysUpTime at the time when the rdnRQueryCmtsCmStatusTable values for this CM were last polled.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.4981.2.2.15.1.6

This table contains statistics summarizing UGS flows
per CMTS slot/port on the BSR.

rdnCableUgsStatsEntry row .1.3.6.1.4.1.4981.2.2.17.1

A row in the rdnCableUgsStatsTable. Each row
contains a set of statistics, totaled for all UGS flows
on a particular upstream port. The table is indexed by
values of ifIndex that are associated with CMTS
upstream po…

Indexes

IF-MIBifIndex

Column	Syntax	OID
rdnCableUgsStatsSlot The physical chasis slot number relative to the containing card or chassis, to which this row of UGS statistics is applying.	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.4981.2.2.17.1.1
rdnCableUgsStatsPort Chassis port number, on the associated card, to which this row of UGS statistics is applying.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.2
rdnCableUgsCurrentTotalFlows Snap shot of the current, total number of UGS flows that are active, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.3
rdnCableUgsMaxFlowsLastFiveMinutes Maximum number of UGS flows that were active, during the last 5 minutes, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.4
rdnCableUgsAvFlowsLastFiveMinutes Average number of UGS flows that were active, during the last 5 minutes, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.5
rdnCableUgsMinFlowsLastFiveMinutes Minimum number of UGS flows that were active, during the last 5 minutes, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.6
rdnCableUgsMaxFlowsLastWindow Maximum number of UGS flows that were active, during the rdnUgsStatsWindow, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.7
rdnCableUgsAvFlowsLastWindow Average number of UGS flows that were active, during the rdnUgsStatsWindow, for the associated ifIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.8
rdnCableUgsMinFlowsLastWindow Minimum number of UGS flows that were active, during the rdnUgsStatsWindow, for the associated ifIndex interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.17.1.9
rdnCableUgsResetStats A 'set' of this object to TRUE(1) will cause all statistics in the row to be reset to zero. This object will always return FALSE(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4981.2.2.17.1.10

This table contains statistics summarizing 
non-bonded flows within Service Classes on the BSR.

rdnServiceClassStatsEntry row .1.3.6.1.4.1.4981.2.2.18.1

A row in the rdnServiceClassStatsTable. Each row
contains a set of statistics related to flows within
a particular service class, and associated with a
particular value of ifIndex. The table is indexed by:
…

Indexes

IF-MIBifIndex DOCS-QOS3-MIBdocsQosServiceClassName

Column	Syntax	OID
rdnServiceClassStatsIfDirection Specifies whether the associated service class template applies to upstream or downstream service flows.	DOCS-IF3-MIBIfDirection Type Values: 1 downstream 2 upstream	.1.3.6.1.4.1.4981.2.2.18.1.1
rdnServiceClassStatsSlot The physical chasis slot number relative to the containing card or chassis, to which this row of service class statistics is applying.	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.4981.2.2.18.1.2
rdnServiceClassStatsPort Chassis port number, on the associated card, to which this row of service class statistics is applying.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.3
rdnServiceClassStatsTotalPackets Count of total packets that have been transmitted, for the associated ifIndex and service class.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.18.1.4
rdnServiceClassStatsTotalBytes Count of total bytes that have been transmitted, for the associated ifIndex and service class.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.18.1.5
rdnServiceClassCurrentTotalFlows Snap shot of the current, total number of flows that are admitted and active, for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.6
rdnServiceClassDeferredFlows Count of deferred flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.7
rdnServiceClassRestrictedFlows Count of restricted flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.8
rdnServiceClassRejectedFlows Count of rejected flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.9
rdnServiceClassBandWidth Admitted bandwidth, in bits per second, for this ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.18.1.10
rdnServiceClassResetStats A 'set' of this object to TRUE(1) will cause all statistics in the row to be reset to zero. This applies to BOTH non-bonded and bonded statistics for the specified ifIndex and service class.a This object will always ret…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4981.2.2.18.1.11

This table describes the set of Motorola-QoS Services in a CMTS

rdnCmtsServiceClassEntry row .1.3.6.1.4.1.4981.2.2.19.1.1

List of attributes of private service class.

Indexes

rdnCmtsServiceClassName

Column	Syntax	OID
rdnCmtsServiceClassName This object is the Service Class Name. DOCSIS specifies that the maximum size is 15 printable ASCII characters with a terminating zero. The terminating Zero is not represented in this DisplayString syntax object.	OctetString Constraints: range: 1-15	.1.3.6.1.4.1.4981.2.2.19.1.1.1
rdnCmtsServiceClassMab This object is get/set Maximum Assigned Bandwidth(MAB) for specified ServiceClass.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.19.1.1.2
rdnCmtsServiceClassCap This object is get/set Configured Active Percent(CAP) for specified ServiceClass.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.19.1.1.3
rdnCmtsServiceClassSchedulingPriority This object is to get/set Scheduling Priority for specified ServiceClass.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.19.1.1.4
rdnCmtsServiceClassAdmittedBWThreshold This object is to get/set Admitted Bandwidth Threshold for specified ServiceClass.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.19.1.1.5
rdnCmtsServiceClassAllowShare This object is to get/set allow bandwidth share with other class for specified ServiceClass.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4981.2.2.19.1.1.6

This is an extension of the rdnRQueryCmtsCmStatusTable.

rdnRQueryCmtsCmStatusExtEntry row .1.3.6.1.4.1.4981.2.2.20.1

An entry in the rdnRQueryCmtsCmStatusExtTable.
The table is indexed by a rdnRQueryCmtsCmStatusEntry.

Indexes

No indexes recorded

Column	Syntax	OID
rdnRQuerySwCurrentVers The model and software version of this CM as parsed from its sysDescr.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4981.2.2.20.1.1
rdnRQueryServerConfigFile The configuration file of the modem.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4981.2.2.20.1.2

This table is an extension of the docsIfCmtsCmTable. It
provides additional information about the CM.

rdnIfCmtsCmEntry row .1.3.6.1.4.1.4981.2.2.21.1

Each entry of the table rdnIfCmtsCmTable. Each entry
Provides some additional information about the CM.

Indexes

No indexes recorded

Column	Syntax	OID
rdnIfCmtsCmMaxCpeNumber The maximum number of permitted CPEs connecting to the modem. The value 0 means no maximum limit. By default maximum of 16 CPEs are allowed behind a single CM. Setting the value will not affect the already connected CP…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.4981.2.2.21.1.1
rdnIfCmtsCmCurrCpeNumber The current number of CPEs connecting to the modem. The value 0 means no hosts connecting to the modem	Integer32 Constraints: range: 0-255	.1.3.6.1.4.1.4981.2.2.21.1.2

A set of objects in the CMTS, maintained for each
MTA ONLY connected to this CMTS.

rdnIfCmtsMTAOnlyStatusEntry row .1.3.6.1.4.1.4981.2.2.23.1

Status information for a single MTA.
An entry in this table exists for each Cable Modem Only
that is connected to the CMTS implementing this table.

Indexes

rdnIfCmtsMTAOnlyStatusIndex

Column	Syntax	OID
rdnIfCmtsMTAOnlyStatusIndex Index value to uniquely identify an entry in this table. For an individual MTA Only, this index value should not change during CMTS uptime.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.4981.2.2.23.1.1
rdnIfCmtsMTAOnlyStatusMacAddress MAC address of this MTA. If the MTA has multiple MAC addresses, this is the MAC address associated with the Cable interface.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.23.1.2
rdnIfCmtsMTAOnlyStatusIpAddressdeprecated IP address of this MTA. If the MTA has no IP address assigned, or the IP address is unknown, this object returns a value of 0.0.0.0. If the MTA has multiple IP addresses, this object returns the IP address associated wi…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.4981.2.2.23.1.3
rdnIfCmtsMTAOnlyStatusDownChannelIfIndex IfIndex of the downstream channel this MTA is connected to. If the downstream channel is unknown, this object returns a value of zero.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4981.2.2.23.1.4
rdnIfCmtsMTAOnlyStatusUpChannelIfIndex IfIndex of the upstream channel this MTA is connected to. If the upstream channel is unknown, this object returns a value of zero.	IF-MIBInterfaceIndexOrZero Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4981.2.2.23.1.5
rdnIfCmtsMTAOnlyStatusRxPower The receive power as perceived for upstream data from this MTA. If the receive power is unknown, this object returns a value of zero.	dBmVDOCS-IF-MIBTenthdBmV	.1.3.6.1.4.1.4981.2.2.23.1.6
rdnIfCmtsMTAOnlyStatusTimingOffset A measure of the current round trip time for this MTA. Used for timing of CM upstream transmissions to ensure synchronized arrivals at the CMTS. Units are in terms of 6.25 microseconds/(64*256). Returns zero if the valu…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.23.1.7
rdnIfCmtsMTAOnlyStatusEqualizationData Equalization data for this MTA. Returns an empty string if the value is unknown or if there is no equalization data available or defined.	OctetString	.1.3.6.1.4.1.4981.2.2.23.1.8
rdnIfCmtsMTAOnlyStatusValue Current MTA connectivity state, as specified in the RF Interface Specification. Returned status information is the CM status as assumed by the CMTS, and indicates the following events: other(1) Any state other than b…	Enumeration Enumerated Values: 1 other 2 ranging 3 rangingAborted 4 rangingComplete 5 ipComplete 6 registrationComplete 7 accessDenied 8 operational 9 registeredBPIInitializing	.1.3.6.1.4.1.4981.2.2.23.1.9
rdnIfCmtsMTAOnlyStatusUnerroreds Codewords received without error from this MTA.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.23.1.10
rdnIfCmtsMTAOnlyStatusCorrecteds Codewords received with correctable errors from this MTA.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.23.1.11
rdnIfCmtsMTAOnlyStatusUncorrectables Codewords received with uncorrectable errors from this MTA.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.23.1.12
rdnIfCmtsMTAOnlyStatusSignalNoise Signal/Noise ratio as perceived for upstream data from this MTA. If the Signal/Noise is unknown, this object returns a value of zero.	dBDOCS-IF-MIBTenthdB	.1.3.6.1.4.1.4981.2.2.23.1.13
rdnIfCmtsMTAOnlyStatusMicroreflections Total microreflections including in-channel response as perceived on this interface, measured in dBc below the signal level. This object is not assumed to return an absolutely accurate value, but should give a rough ind…	dBcInteger32 Constraints: range: 0-255	.1.3.6.1.4.1.4981.2.2.23.1.14
rdnIfCmtsMTAOnlyStatusExtUnerroreds Codewords received without error from this MTA.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.23.1.15
rdnIfCmtsMTAOnlyStatusExtCorrecteds Codewords received with correctable errors from this MTA.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.23.1.16
rdnIfCmtsMTAOnlyStatusExtUncorrectables Codewords received with uncorrectable errors from this MTA.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.23.1.17
rdnIfCmtsMTAOnlyStatusDocsisRegMode Indication whether the MTA has registered using 1.0 Class of Service or 1.1 Quality of Service. This object mirrors docsIfCmtsCmStatusDocsisMode from the docsIfExt mib.	DOCS-IF-MIBDocsisQosVersion Type Values: 1 docsis10 2 docsis11	.1.3.6.1.4.1.4981.2.2.23.1.18
rdnIfCmtsMTAOnlyStatusModulationType Indicates modulation type currently used by the MTA. Since this object specifically identifies PHY mode, the shared type is not permitted. If the upstream channel is unknown, this object returns a value of zero.	DOCS-IF-MIBDocsisUpstreamType Type Values: 0 unknown 1 tdma 2 atdma 3 scdma 4 tdmaAndAtdma	.1.3.6.1.4.1.4981.2.2.23.1.19
rdnIfCmtsMTAOnlyStatusInetAddressType The type of internet address of docsIfCmtsCmStatusInetAddress. If the MTA Internet address is unassigned or unknown, then the value of this object is unknown(0).	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4981.2.2.23.1.20
rdnIfCmtsMTAOnlyStatusInetAddress Internet address of this MTA. If the MTA has no Internet address assigned, or the Internet address is unknown, the value of this object is the empty string. If the MTA has multiple Internet addresses, this object return…	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.4981.2.2.23.1.21
rdnIfCmtsMTAOnlyStatusValueLastUpdate The value of sysUpTime when docsIfCmtsCmStatusValue was last updated.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.4981.2.2.23.1.22

This table contains statistics summarizing flows
within Service Classes for bonded upstreams and downstreams 
on the BSR.  For non-bonded upstream/downstream stats, 
please refer to rdnServiceClassStatsTable

rdnServiceClassBondingStatsEntry row .1.3.6.1.4.1.4981.2.2.24.1

A row in the rdnServiceClassBondingStatsTable. Each row
contains a set of statistics related to flows within
a particular service class, and associated with a
particular value of ifIndex. The table is indexed by:
…

Indexes

IF-MIBifIndex rdnServiceClassBondingStatsIfDirection DOCS-QOS3-MIBdocsQosServiceClassName rdnServiceClassBondingStatsMacIfIndex rdnServiceClassBondingStatsGroupId

Column	Syntax	OID
rdnServiceClassBondingStatsMacIfIndex The MAC interface index under which this downstream channel's bonding group is configured. This will be an ifType of docsCableMaclayer(127).	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4981.2.2.24.1.1
rdnServiceClassBondingStatsGroupId The downstream or upstream bonding group identifier.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.4981.2.2.24.1.2
rdnServiceClassBondingStatsIfDirection Specifies whether the associated service class template applies to downstream(1) or upstream(2) service flows.	DOCS-IF3-MIBIfDirection Type Values: 1 downstream 2 upstream	.1.3.6.1.4.1.4981.2.2.24.1.3
rdnServiceClassBondingStatsSlot The physical chasis slot number relative to the containing card or chassis, to which this row of service class statistics is applying.	Integer32 Constraints: range: 0-15	.1.3.6.1.4.1.4981.2.2.24.1.4
rdnServiceClassBondingStatsChan Channel number on the associated card, to which this row of service class statistics is applying.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.5
rdnServiceClassBondingCurrentTotalFlows Snap shot of the current, total number of flows that are admitted and active, for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.6
rdnServiceClassBondingDeferredFlows Count of deferred flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.7
rdnServiceClassBondingRestrictedFlows Count of restricted flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.8
rdnServiceClassBondingRejectedFlows Count of rejected flows for the associated ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.9
rdnServiceClassBondingBandWidth Admitted bandwidth, in bits per second, for this ifIndex and service class.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.4981.2.2.24.1.10

This table provides the information about the configured cable
intercepts

rdnCableInterceptEntry row .1.3.6.1.4.1.4981.2.2.27.1

An entry of the table rdnCableInterceptTable.
The table is indexed by ifIndex and CPE MAC address.
For bridged cable intercept entries the ifIndex is 0.
For routed cable intercept entries the ifIndex is the
index of …

Indexes

IF-MIBifIndex rdnCableInterceptCpeMac

Column	Syntax	OID
rdnCableInterceptCpeMac The Mac Address of the CPE being intercepted. Also being used as index.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.27.1.1
rdnCableInterceptCmMac The Mac Address of the CM being intercepted. For bridged cable intercept entries, the MAC address of the bridged CM. For routed cable intercept entries, the octet string of '000000000000'	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.4981.2.2.27.1.2
rdnCableInterceptDestination1Type Type of the address of the first lawful intercept collector. Currently only IPv4 is supported.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4981.2.2.27.1.3
rdnCableInterceptDestination1Ip Ip destination 1 of 3 for captured data.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4981.2.2.27.1.4
rdnCableInterceptDestination1Port Port destination 1 of 3 for captured data.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.4981.2.2.27.1.5
rdnCableInterceptDestination2Type Type of the address of the second lawful intercept collector. Currently only IPv4 is supported.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4981.2.2.27.1.6
rdnCableInterceptDestination2Ip Ip destination 2 of 3 for captured data.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4981.2.2.27.1.7
rdnCableInterceptDestination2Port Port destination 2 of 3 for captured data.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.4981.2.2.27.1.8
rdnCableInterceptDestination3Type Type of the address of the third lawful intercept collector. Currently only IPv4 is supported.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4981.2.2.27.1.9
rdnCableInterceptDestination3Ip Ip destination 3 of 3 for captured data.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4981.2.2.27.1.10
rdnCableInterceptDestination3Port Port destination 3 of 3 for captured data.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.4981.2.2.27.1.11
rdnCableInterceptSourceType Type of the address of the source addr. Currently only IPv4 is supported	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.4981.2.2.27.1.12
rdnCableInterceptSourceIp Source ip of intercepted data.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4981.2.2.27.1.13
rdnCableInterceptPktCnt Number of packets intercepted.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.27.1.14
rdnCableInterceptByteCnt Number of bytes intercepted.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.27.1.15
rdnCableInterceptRowStatus Controls and reflects the status of rows in this table. This field is used to control the addition and deletion of a cable intercept entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4981.2.2.27.1.16

This table contains 32 bit and 64 bit 
IUC-1 Noise and NoEnergy mini-slots counters 
for upstream channels.

rdnCmtsUpChannelCounterEntry row .1.3.6.1.4.1.4981.2.2.28.1

List of noise/collision statistics for a single upstream channel.
For DOCSIS 3.0 or 2.0 CMTSs, an entry in this table
exists for each ifEntry with an ifType of docsCableUpstreamChannel(205).

For DOCSIS 1.x …

Indexes

IF-MIBifIndex

Column	Syntax	OID
rdnIfCmtsUpChCtrReqNoise Current count, from CMTS initialization, of contention request mini-slots subjected to Noise on this upstream logical channel. This includes all contention mini-slots for IUC1 applicable to bursts that the CMTS detected…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.28.1.1
rdnIfCmtsUpChCtrReqNoEnergy Current count, from CMTS initialization, of contention request mini-slots subjected to No Energy on this upstream logical channel. This includes all contention mini-slots for IUC1 applicable to bursts that the CMTS dete…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4981.2.2.28.1.2
rdnIfCmtsUpChCtrExtReqNoise Current count, from CMTS initialization, of contention request mini-slots for which no energy was detected on this upstream logical channel.This includes all contention mini-slots for IUC1 applicable to bursts that t…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.28.1.3
rdnIfCmtsUpChCtrExtReqNoEnergy Current count, from CMTS initialization, of contention request mini-slots for which no energy was detected on this upstream logical channel. This includes all contention mini-slots for IUC1 applicable to bursts that …	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.4981.2.2.28.1.4