PDN-DOT1QEXT-MIB Table View

The Paradyne dot1qVlanStatic extension table.
This table is used for configuring extensions 
to static vlans.

pdnDot1qVlanStaticExtEntry row .1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1

An entry in the Paradyne dot1q extension to
Static Vlan Table

Indexes

No indexes recorded

Column	Syntax	OID
pdnDot1qVlanStaticSecureModeStatus This is objects configure secure mode status for the selected VLAN. The secure VLAN mode implies that the users on this VLAN cannot talk to users on a different VLAN. This setting also validates the configuration of …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.1
pdnDot1qVlanStaticProxyArpStatus This objects enables/disabled proxy arp on secure VLAN. If the VLAN is secure, it can optionally have Proxy ARP enabled. This object is not valid unless pdnDot1qVlanStaticSecureModeStatus is set to ENABLED.This object …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.2
pdnDot1qVlanStaticUplink This is used to configure the port number of the port on which all frames belonging to secure VLAN are to be forwarded. This object is not valid unless pdnDot1qVlanStaticSecureModeStatus is set to ENABLED. If pdnDot1qV…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.3
pdnDot1qVlanStaticDefaultNHR This object is used to configure Default Next Hop Router Ip Address that would be used only if the Next Hop Router cannot be learned (i.e from snooping messages). This object is not valid unless pdnDot1qVlanStaticSecure…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.4
pdnDot1qVlanStaticOuterTag When VLAN stacking (Q in Q) is desired, this object contains the value of the outer 802.1q VLAN outer tag. A value of zero (0) indicates that VLAN stacking is not enabled.	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.5
pdnDot1qVlanStaticOuterDefaultPriority When VLAN stacking (Q in Q) is desired, this object contains the default value of the priority bits in the 802.1q VLAN outer tag for unknown unicast, broadcast and multicast packets. For known unicast tra…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.6
pdnDot1qVlanStaticOuterEthertype When VLAN stacking (Q in Q) is desired, this object contains the value of the ethertype in the 802.1q VLAN outer tag. If pdnDot1qVlanStaticOuterTag (above) is zero (0) this object is ignored.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.1795.2.24.2.39.1.1.1.1.7

This table allows mapping of Bridge Ports and Priorities.
          
In General, every bridge port has an associated physical port
port (identified by its ifIndex). This relationship is defined
in the Dot1dBasePortTable (RFC1493).
          
In addition, each bridge port is associated with one priority
(PIWG) from a range of valid priorities. This table defines 
this relationship. 
          
The range of priorities can vary from product to product.

pdnDot1BasePortPIWGEntry row .1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1

The priority (PIWG) defined on a Bridge port.

Indexes

IF-MIBifIndex pdnDot1BasePort

Column	Syntax	OID
pdnDot1BasePort This object specifies the bridge port associated with this PIWG	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.1
pdnDot1BasePortPIWGId This is the integer identifier of the priority (PIWG)	Unsigned32 Constraints: range: 1-8	.1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.2
pdnDot1BasePortPIWGCircuit This is the object identifier of the priority (PIWG), The value of this object must be a valid identifier defined under the Paradyne Enterprise Definitions (pdn_Header.mib).	ObjectIdentifier	.1.3.6.1.4.1.1795.2.24.2.39.1.1.2.1.3