NORTEL-WLAN-AP-MIB Table View

Table of descriptive and status information about
configuration of each RS-232 line in this system

ntWlanLineEntry row .1.3.6.1.4.1.45.1.11.1.2.1.1

An entry in the table, containing information
about configuration in one RS232 line of the Access
Point.

Indexes

ntWlanLineIndex

Column	Syntax	OID
ntWlanLineIndex This is defined as RS-232 index.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.45.1.11.1.2.1.1.1
ntWlanLineDataBits This is defined as number of data bits for the RS232 interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.45.1.11.1.2.1.1.2
ntWlanLineParity This is defined as parity of the RS232 interface.	Enumeration Enumerated Values: 1 odd 2 even 99 none	.1.3.6.1.4.1.45.1.11.1.2.1.1.3
ntWlanLineSpeed This is defined as the speed of the RS-232 interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.45.1.11.1.2.1.1.4
ntWlanLineStopBits This is defined as the number of stop bits for the RS-232 interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.45.1.11.1.2.1.1.5

Table of descriptive and status information about
configuration of each switch port (including expansion
slot) in this system. This table also contains information
about each trunk (similar to Cisco's EtherChannel).

ntWlanPortEntry row .1.3.6.1.4.1.45.1.11.1.3.1.1

An entry in the table, containing information
about configuration in one switch port of the switch.

Indexes

ntWlanPortIndex

Column	Syntax	OID
ntWlanPortIndex This is defined as ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.1.11.1.3.1.1.1
ntWlanPortName Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).	OctetString Constraints: range: 0-64	.1.3.6.1.4.1.45.1.11.1.3.1.1.2
ntWlanPortType Indicates the port type.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseMiniGBIC	.1.3.6.1.4.1.45.1.11.1.3.1.1.3
ntWlanPortSpeedDpxCfg Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100…	Enumeration Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.45.1.11.1.3.1.1.4
ntWlanPortFlowCtrlCfg (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in…	Enumeration Enumerated Values: 1 enabled 2 disabled 3 backPressure 4 dot3xFlowControl	.1.3.6.1.4.1.45.1.11.1.3.1.1.5
ntWlanPortCapabilities Port capabilities.	Enumeration Enumerated Values: 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 reserved6 7 reserved7 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl 99 portCap10half	.1.3.6.1.4.1.45.1.11.1.3.1.1.6
ntWlanPortAutonegotiation Whether autonegotiation is enabled.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.45.1.11.1.3.1.1.7
ntWlanPortSpeedDpxStatus The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this …	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.45.1.11.1.3.1.1.8
ntWlanPortFlowCtrlStatus (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, thi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.45.1.11.1.3.1.1.9

Table of descriptive and status information about
configuration of each radio of the AP.

ntWlanDot11PhyOperationEntry row .1.3.6.1.4.1.45.1.11.1.7.4.1.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

ntWlanDot11Index

Column	Syntax	OID
ntWlanDot11Index Radio index of the AP.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.45.1.11.1.7.4.1.1.1
ntWlanDot11TurboModeEnabled This attribute, when true, shall indicate that the nortel's propietory turbo mode option is enabled. The default value of this attribute shall be false.	Enumeration Enumerated Values: 1 on 2 off 99 none	.1.3.6.1.4.1.45.1.11.1.7.4.1.1.3
ntWlanDot11PreambleLength This attribute determines whether or not a short or a long preamble is used to delineate 802.11 frames.	Enumerationr/w Enumerated Values: 1 short 2 long 99 twelveSymbols	.1.3.6.1.4.1.45.1.11.1.7.4.1.1.4
ntWlanDot11dWorldModeEnabled This attribute determines whether 802.11d world mode is enabled for this radio.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.1.11.1.7.4.1.1.5
ntWlanDot11ClosedSystem This attribute determines whether the radio operates as a closed system. When configured as a closed system, the SSID is not included when broadcasting periodic beacon frames.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.1.11.1.7.4.1.1.6

Table of descriptive and status information about
configuration of each authentication server.

ntWlanDot11AuthenticationServerEntry row .1.3.6.1.4.1.45.1.11.1.7.6.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

ntWlanDot11ServerIndex

Column	Syntax	OID
ntWlanDot11ServerIndex Radio index of the AP.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.45.1.11.1.7.6.1.1
ntWlanDot11AuthenticationServer This values indicates the IP address of the authentication server.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.45.1.11.1.7.6.1.2
ntWlanDot11AuthenticationPort This values indicates the UDP Port used by the primary authentication server.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.45.1.11.1.7.6.1.3
ntWlanDot11AuthenticationKey This values indicates the shared key used by the authentication server.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.45.1.11.1.7.6.1.4
ntWlanDot11AuthenticationRetransmit This values indicates the retransmit timer length used by the authentication server.	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.45.1.11.1.7.6.1.5
ntWlanDot11AuthenticationTimeout This values indicates the Timeout value(sec) used by the authentication server.	SecondsInteger32r/w Constraints: range: 1-60	.1.3.6.1.4.1.45.1.11.1.7.6.1.6
ntWlanDot11SecondaryAuthServer This values indicates the IP address of the secondary authentication server.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.45.1.11.1.7.6.1.7
ntWlanDot11SecondaryAuthPort This values indicates the UDP Port used by the primary secondary authentication server.	Integer32r/w Constraints: range: 1024-65535	.1.3.6.1.4.1.45.1.11.1.7.6.1.8
ntWlanDot11SecondaryAuthKey This values indicates the shared key used by the secondary authentication server.	OctetStringr/w Constraints: range: 0-20	.1.3.6.1.4.1.45.1.11.1.7.6.1.9
ntWlanDot11SecondaryAuthRetransmit This values indicates the retransmit timer length used by the secondary authentication server.	Integer32r/w Constraints: range: 1-30	.1.3.6.1.4.1.45.1.11.1.7.6.1.10
ntWlanDot11SecondaryAuthTimeout This values indicates the Timeout value(sec) used by the secondary authentication server.	SecondsInteger32r/w Constraints: range: 1-60	.1.3.6.1.4.1.45.1.11.1.7.6.1.11

Table of status information about
each configured MAC Address Filtering Entry.

ntWlanDot11FilterEntry row .1.3.6.1.4.1.45.1.11.1.7.7.1

An entry in the table, containing information
about configuration in one radio of the AP.

Indexes

ntWlanDot11FilterIndex

Column	Syntax	OID
ntWlanDot11FilterIndex Filter index.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.45.1.11.1.7.7.1.1
ntWlanDot11FilterAddress This values indicates the MAC address of the filter entry.	SNMPv2-TCPhysAddressr/w Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.45.1.11.1.7.7.1.2
ntWlanDot11FilterStatus This values indicates the Status of the filter entry. Ifallowed, the client is allowed access to the network. If disallowed, the no frames will be forwarded to the network from the client.	Enumerationr/w Enumerated Values: 30 allowed 31 denied	.1.3.6.1.4.1.45.1.11.1.7.7.1.3

Table of status information for Association and
Disassociation Trap

ntWlanDot11TrapEntry row .1.3.6.1.4.1.45.1.11.1.7.9.1

An entry in the table, containing information
for the association and disassociation trap.

Indexes

ntWlanDot11InterfaceIndex

Column	Syntax	OID
ntWlanDot11InterfaceIndex Interface index.	Integer32 Constraints: range: 1-2147483647	.1.3.6.1.4.1.45.1.11.1.7.9.1.1
ntWlanDot11AssociationStationAddress This values indicates the MAC address of the Mobile Unit associating with this Access Point.	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.45.1.11.1.7.9.1.2
ntWlanDot11DisassociationStationAddress This values indicates the MAC address of the Mobile Unit no longer associated with this Access Point.	SNMPv2-TCPhysAddress Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.45.1.11.1.7.9.1.3
ntWlanDot11AssociationMU This values indicates the number of Mobile Units associated on the Interface	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.45.1.11.1.7.9.1.4

Table to configure which hardware-supported rates are
actively supported, and which are basic rates required
for an MU to connect to an AP.  Entries must exist in
this table for every hardware-supported rate for each
appropriate ifIndex value.

ntWlanApRateSupportEntry row .1.3.6.1.4.1.45.1.11.1.10.1.1

An entry in the ntWlanApRateSupportTable.

Indexes

ntWlanApRateSupportIfIndex ntWlanApRateSupportSpeed

Column	Syntax	OID
ntWlanApRateSupportIfIndex The ifIndex value of the radio.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.1.11.1.10.1.1.1
ntWlanApRateSupportSpeed A supported data rate.	NtWlanApDataRate Type Constraints: range: 2..127	.1.3.6.1.4.1.45.1.11.1.10.1.1.2
ntWlanApRateSupportLevel This object indicates whether a specific rate is currently supported, and if so, whether it is a basic rate. off - indicates that this rate is not currently supported. supporte…	Enumerationr/w Enumerated Values: 0 off 1 supported 2 supportedBasic	.1.3.6.1.4.1.45.1.11.1.10.1.1.3

Table to configure WEP and WPA security parameters.
Entries are per-radio.

ntWlanApSecurityEntry row .1.3.6.1.4.1.45.1.11.1.11.1.1

An entry in the ntWlanApSecurityTable.

Indexes

ntWlanApSecurityIfIndex

Column	Syntax	OID
ntWlanApSecurityIfIndex The ifIndex value of the radio.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.1.11.1.11.1.1.1
ntWlanApSecurityEnabled Indicates whether security is enabled for a radio.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.45.1.11.1.11.1.1.2
ntWlanApSecurityWEPAuthType The WEP authentication type.	Enumerationr/w Enumerated Values: 0 openSystem 1 sharedKey	.1.3.6.1.4.1.45.1.11.1.11.1.1.3
ntWlanApSecurityWEPKeyLength Indicates the WEP key length being used.	Enumerationr/w Enumerated Values: 0 wepKey64 1 wepKey128 2 wepKey152	.1.3.6.1.4.1.45.1.11.1.11.1.1.4
ntWlanApSecurityWEPActiveKey Indicates which WEP key is currently in use.	Integer32r/w Constraints: range: 1-4	.1.3.6.1.4.1.45.1.11.1.11.1.1.5
ntWlanApSecurityWEPKey1 The first WEP key. Retrieval of this object will always return an empty string.	NtWlanApWEPKeyr/w Type Constraints: range: 0 range: 5 range: 13 range: 16	.1.3.6.1.4.1.45.1.11.1.11.1.1.6
ntWlanApSecurityWEPKey2 The second WEP key. Retrieval of this object will always return an empty string.	NtWlanApWEPKeyr/w Type Constraints: range: 0 range: 5 range: 13 range: 16	.1.3.6.1.4.1.45.1.11.1.11.1.1.7
ntWlanApSecurityWEPKey3 The third WEP key. Retrieval of this object will always return an empty string.	NtWlanApWEPKeyr/w Type Constraints: range: 0 range: 5 range: 13 range: 16	.1.3.6.1.4.1.45.1.11.1.11.1.1.8
ntWlanApSecurityWEPKey4 The fourth WEP key. Retrieval of this object will always return an empty string.	NtWlanApWEPKeyr/w Type Constraints: range: 0 range: 5 range: 13 range: 16	.1.3.6.1.4.1.45.1.11.1.11.1.1.9
ntWlanApSecurityWPASupport Indicates whether WPA security is supported.	Enumerationr/w Enumerated Values: 1 supported 2 required 3 wepOnly	.1.3.6.1.4.1.45.1.11.1.11.1.1.10
ntWlanApSecurityWPAMode The WPA mode.	Enumerationr/w Enumerated Values: 0 dynamic 1 preSharedKey	.1.3.6.1.4.1.45.1.11.1.11.1.1.11
ntWlanApSecurityWPAPreSharedKey The WPA pre-shared key.	OctetStringr/w Constraints: range: 63-63	.1.3.6.1.4.1.45.1.11.1.11.1.1.12
ntWlanApSecurityWPAMcastCypherMode The multicast cypher mode.	Enumerationr/w Enumerated Values: 0 wep 1 tkip 2 aes	.1.3.6.1.4.1.45.1.11.1.11.1.1.13

Table to configure mappings from ethernet type
to queue number.

ntWlanApQoSEtherTypeToQueueEntry row .1.3.6.1.4.1.45.1.11.1.12.2.1

An entry in the ntWlanApQoSTable.

Indexes

ntWlanApQoSEtherTypeToQueueIndex

Column	Syntax	OID
ntWlanApQoSEtherTypeToQueueIndex An ethernet type, to be mapped to a queue.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.45.1.11.1.12.2.1.1
ntWlanApQoSEtherTypeToQueueNumber The queue number to which the ether type is mapped.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.45.1.11.1.12.2.1.2
ntWlanApQoSEtherTypeToQueueRowStatus This object is used to create and destroy entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.45.1.11.1.12.2.1.3

Table to configure mappings from ethernet MAC address
to queue number.

ntWlanApQoSMACToQueueEntry row .1.3.6.1.4.1.45.1.11.1.12.3.1

An entry in the ntWlanApQoSTable.

Indexes

ntWlanApQoSMACToQueueAddress

Column	Syntax	OID
ntWlanApQoSMACToQueueAddress An ethernet MAC address, to be mapped to a queue.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.1.11.1.12.3.1.1
ntWlanApQoSMACToQueueNumber The queue number to which the MAC address is mapped.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.45.1.11.1.12.3.1.2
ntWlanApQoSMACToQueueRowStatus This object is used to create and destroy entries in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.45.1.11.1.12.3.1.3

Table to configure the default VID per-radio.

ntWlanApVlanEntry row .1.3.6.1.4.1.45.1.11.1.13.2.1

An entry in the ntWlanApVlanTable.

Indexes

ntWlanApVlanIfIndex

Column	Syntax	OID
ntWlanApVlanIfIndex The ifIndex value of the radio.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.45.1.11.1.13.2.1.1
ntWlanApVlanDefaultVid The default VID of the radio.	Integer32r/w Constraints: range: 0-4094	.1.3.6.1.4.1.45.1.11.1.13.2.1.2

Table containing mappings from Mobile Unit MAC
addresses to VLAN ID values.

ntWlanApVlanMUMACToVidEntry row .1.3.6.1.4.1.45.1.11.1.13.3.1

An entry in the ntWlanApVlanMUMACToVidTable.

Indexes

ntWlanApVlanMUMACToVidAddress

Column	Syntax	OID
ntWlanApVlanMUMACToVidAddress The ethernet MAC address of a Mobile Unit.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.1.11.1.13.3.1.1
ntWlanApVlanMUMACToVidNumber The VID to which this Mobile Unit's MAC is mapped.	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.45.1.11.1.13.3.1.2

Table of per-Mobile Unit statistics.

ntWlanApMUStatsEntry row .1.3.6.1.4.1.45.1.11.1.14.1.1

An entry in the ntWlanApMUStatsTable.

Indexes

ntWlanApMUStatsMUAddress

Column	Syntax	OID
ntWlanApMUStatsMUAddress The ethernet MAC address of the Mobile Unit.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.45.1.11.1.14.1.1.1
ntWlanApMUStatsPacketsIn A count of the packets received from this MU.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.45.1.11.1.14.1.1.2
ntWlanApMUStatsPacketsOut A count of the packets sent to this MU.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.45.1.11.1.14.1.1.3
ntWlanApMUStatsOctetsIn A count of the octets received from this MU.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.45.1.11.1.14.1.1.4
ntWlanApMUStatsOctetsOut A count of the octets sent to this MU.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.45.1.11.1.14.1.1.5