NETI-TRUNK-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
73

dppipTable

table
.1.3.6.1.4.1.2928.2.3.1.1.3 · 1 row entry · 51 columns
Open in standard view
Uses the netinsight variant from /opt/observium/mibs/netinsight.
Command help
Walk dppipTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'NETI-TRUNK-MIB' -M '/opt/observium/mibs/netinsight:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'NETI-TRUNK-MIB::dppipTable' 
A list of DPP-IP interface entries.  The number of entries is
given by the value of dppipNumber.  The following objects
need to be written simultaneously, i.e. as a single write
operation, while dppipAdminStatus is `up': dppipTxSlots,
dppipMtu, dppipTxFecMode, dppipTxFecRows, dppipTxFecCols
dppipEntry row .1.3.6.1.4.1.2928.2.3.1.1.3.1
A DPP-IP interface entry containing objects at the subnetwork
layer and below for a particular interface.
Indexes
Column Syntax OID
dppipIndex
A value greater than zero that is unique for each DPP-IP
interface. The value for each DPP-IP interface must remain
constant at least from one re-initialization of the entity's
network management system to the next re-i…
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.1
dppipName
The textual name of the interface. The value of this object
should be the name of the DPP-IP interface as assigned by the
local device.
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.2
dppipAddress
The IPv4 address of the DPP-IP interface.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.3
dppipNetMask
The subnet mask associated with the IP address of DPP-IP
interface. The value of the mask is an IP address with all
the network bits set to 1 and all the hosts bits set to 0.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.4
dppipDefaultGateway
The IPv4 address of the default gateway. Packets addressed to
a destination outside the subnet of the DPP-IP interface are
by default routed to this gateway.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.5
dppipPeerAddress
The IPv4 address of the peer DPP-IP interface at the remote
end of the DTM trunk.
SNMPv2-SMIIpAddressr/w
Type Constraints:
range: 4
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.6
dppipTxSlots
The DPP-IP interface's current transmit side capacity in
slots per DTM frame.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.7
dppipTxUsedCapacity
An estimate of the transmit side physical layer capacity used
by the DPP-IP interface in bits per second. It represents a
minimum required capacity along the network path.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.8
dppipRxSlots
The DPP-IP interface's current receive side
capacity in slots per DTM frame.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.9
dppipRxUsedCapacity
An estimate of the receive side physical layer capacity used
by the DPP-IP interface in bits per second. It represents a
minimum required capacity along the network path.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.10
dppipDelayVariation
The RMS (i.e. standard deviation) value of the DPP-IP path
delay variation in ns. This value represents a momentary
snapshot of the delay variation.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.11
dppipOperStatus
The current operational state of the interface. The
testing(3) state indicates that no operational frames can be
passed.
Enumeration
Enumerated Values:
1up
2down
3testing
4unknown
5dormant
6notPresent
7lowerLayerDown
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.12
dppipFailure
A textual string describing a fault status on the DPP-IP
interface. The object presents an empty string if there are
no faults on the interface.
SNMP-FRAMEWORK-MIBSnmpAdminString
Type Constraints:
range: 0..255
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.13
dppipReceivedFrames
The total number of DPP-IP frames that have been received.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.14
dppipMissingFrames
The number of DPP-IP frames that were missing in the frame
sequence, i.e. the expected sequence numbers were not found
in the DPP-IP framing buffer.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.15
dppipDeliveredFrames
The total number of DPP-IP data frames that have been
delivered to the DTM interface.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.16
dppipDroppedFrames
The number of DPP-IP frames that have been received and have
not been processed since the interface was unable to align
them to the DPP-IP frame sequence.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.17
dppipDuplicateFrames
The number of DPP-IP frames that were received with a
sequence number of an already processed DPP-IP frame.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.18
dppipReorderedFrames
The number of DPP-IP frames that were received out
of order, but could still be aligned to the DPP-IP
frame sequence.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.19
dppipLostFrames
The number of missing DPP-IP data frames that could not be
delivered to the DTM interface.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.20
dppipRecoveredFrames
The number of missing DPP-IP data frames that were recovered
by the FEC procedure.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.21
dppipSentFrames
The total number of DPP-IP frames that have been sent.
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.22
dppipDelayVarPtp
The point-to-point value of the DPP-IP path delay variation
in nanoseconds. The special value 0 means that the
measurement is incomplete
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.23
dppipDelayVar999
The 99.9 percentile value of the DPP-IP path delay variation
given in nanoseconds. The special value 0 means that the
measurement is incomplete.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.24
dppipAdminStatus
The desired state of the interface.
Enumerationr/w
Enumerated Values:
1up
2down
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.25
dppipVlan
The VLAN identity associated to the DPP-IP interface. The
value 0 indicates that the DPP-IP interface does not belong
to a VLAN. The value -1 indicates that Ethernet frames from
the DPP-IP interface are not tagged.
Integer32r/w
Constraints:
range: -1-4095
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.26
dppipDelayVar01
The 0.1 percentile value of the DPP-IP path delay variation
given in nanoseconds. The special value 0 means that the
measurement is incomplete.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.27
dppipPrio
The Ethernet priority for frames sent from the DPP-IP
interface. Ignored if frames are untagged (i.e. dppipVlan
is -1).
Unsigned32r/w
Constraints:
range: 0-7
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.28
dppipPhysIf
A reference to an object representing the physical interface
that supports the DPP-IP interface. The special value .0.0
is used, when no such reference is available.
SNMPv2-TCRowPointer
Description:
Represents a pointer to a conceptual row. The value is the
name of the instance of the first accessible columnar object
in the conceptual row.

For example, ifIndex.3 would point to the 3rd row in the
ifTable…
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.29
dppipMtu
The Maximum Transmission Unit of the DPP-IP interface,
i.e. the maximum size of the DPP-IP payload, including IP
header, UDP header and DPP-IP header.
Unsigned32r/w
Constraints:
range: 64-1500
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.30
dppipTtl
The Time To Live of frames sent at the DPP-IP interface.
This value is set in the IP header.
Unsigned32r/w
Constraints:
range: 0-127
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.31
dppipDscp
The Differential Services Coding Point of frames sent at the
DPP-IP interface. This value is set in the IP header.
Unsigned32r/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.32
dppipRxSlotsPerFrame
Number of DTM slots per received DPP-IP data frame.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.33
dppipAvailTxSlots
The maximum transmit slot rate (slots/frame) that can be
allocated at the DTM switch.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.34
dppipAvailRxSlots
The maximum receive slot rate (slots/frame) that can be
allocated at the DTM switch.
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.35
dppipMinUsageRatio
The minimum allowed usage ratio (used slots/configured
slots) in per-mille, when dynamic trunk functionality is
used. 1000 is default and indicates that the Dynamic Trunk
function is disabled.

Requires D…
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.36
dppipTxTranspSlots
The DPP-IP interface's current transmit side capacity in
slots per DTM frame that is actually transported over
the. When Dynamic Trunk functionality is disabled this is
equal to dppipTxSlots. When Dynamic Trunk function…
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.37
dppipRxTranspSlots
The DPP-IP interface's current receive side capacity in
slots per DTM frame that is actually transported. When
Dynamic Trunk functionality is disabled this is equal to
dppipRxSlots. When Dynamic Trunk functionality is e…
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.38
dppipNomDTDelay
The nominal extra delay in ns when the Dynamic Trunk
function is enabled.

Requires Dynamic Trunk function support equal to 1.1 or
higher.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.39
dppipTxFecMode
The DPP-IP interface's current mode of operation of the
transmit side Forward Error Correction function (FEC). The
FEC function may be not used (fecNone), used for column
correction (fec1D) or used for both row and colu…
FecModer/w
Type Values:
1fecNone
2fec1D
3fec2D
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.40
dppipTxFecRows
The DPP-IP interface's current number of data rows in the
transmit side Forward Error Correction (FEC) matrix. This
object is not applicable when dppipTxFecMode is fecNone.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.41
dppipTxFecCols
The DPP-IP interface's current number of data columns in the
transmit side Forward Error Correction (FEC) matrix. This
object is not applicable when dppipTxFecMode is fecNone.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.42
dppipRxFecMode
The DPP-IP interface's current mode of operation of the
receive side Forward Error Correction function (FEC). The FEC
function may be not used (fecNone), used for column
correction (fec1D) or used for both row and colum…
FecMode
Type Values:
1fecNone
2fec1D
3fec2D
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.43
dppipRxFecRows
The DPP-IP interface's current number of data rows in the
receive side Forward Error Correction (FEC) matrix. This
object is not applicable when dppipRxFecMode is fecNone.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.44
dppipRxFecCols
The DPP-IP interface's current number of data columns in the
receive side Forward Error Correction (FEC) matrix. This
object is not applicable when dppipRxFecMode is fecNone.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.45
dppipCntControl
Controls the statistics counter monitoring. The statistics
monitoring is restarted and all counters set to 0, by writing
`reset' to this object.
Enumerationr/w
Enumerated Values:
1reset
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.46
dppipSuppressAlarms
Suppression control for alarms from the DPP-IP interface.
When set to `true', all alarms are suppressed.
SNMPv2-TCTruthValuer/w
Type Values:
1true
2false
Description:
Represents a boolean value.
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.47
dppipSigFailFilter
Signal fail filter hold-off time in milliseconds. Trail
Signal Fail conditions must be persistent during the hold-off
time, before operStatus is changed from `up' to `down'.
Unsigned32r/w
Constraints:
range: 0-2000
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.48
dppipDegThreshold
The detection threshold for DEG alarm. A bad second is
declared when the number of errored blocks is equal to or
greater than the threshold, otherwise a good second is
declared. Default is 1200
Unsigned32r/w
Constraints:
range: 1-8000
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.49
dppipDegPeriod
The persistence time for detection of DEG alarm as the number
of consecutive seconds with changed status (bad or good)
before the alarm is set or cleared.
Unsigned32r/w
Constraints:
range: 2-10
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.50
dppipTolJitter
The tolerated jitter and wander of the DPP-IP interface given
in microseconds.
SNMPv2-SMIUnsigned32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.3.1.51

dppipLimitsTable

table
.1.3.6.1.4.1.2928.2.3.1.1.4 · 1 row entry · 12 columns
Open in standard view
Uses the netinsight variant from /opt/observium/mibs/netinsight.
Command help
Walk dppipLimitsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'NETI-TRUNK-MIB' -M '/opt/observium/mibs/netinsight:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'NETI-TRUNK-MIB::dppipLimitsTable' 
A list of DPP-IP interface limits entries.  The number of
entries is given by the value of dppipNumber.
dppipLimitsEntry row .1.3.6.1.4.1.2928.2.3.1.1.4.1
A DPP-IP interface limits entry containing limits for a
particular interface.
Indexes
Column Syntax OID
dppipMaxFecMode
The DPP-IP interface's maximum mode of operation of the
Forward Error Correction function (FEC). The FEC function
may be not used (fecNone), used for column correction (fec1D)
or used for both row and column correction…
FecMode
Type Values:
1fecNone
2fec1D
3fec2D
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.1
dppipMaxFecRows
The DPP-IP interface's maximum number of data rows in the
transmit side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.2
dppipMinFecRows
The DPP-IP interface's minimum number of data rows in the
transmit side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.3
dppipMaxFecCols
The DPP-IP interface's maximum number of data columns in the
transmit side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.4
dppipMinFecCols
The DPP-IP interface's minimum number of data columns in the
transmit side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.5
dppipMaxFecElems
The DPP-IP interface's maximum number of data elements in the
transmit side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.6
dppipMaxTxSlots
The maximum number of slots per DTM frame that can be
allocated at the DPP-IP transmit interface.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.7
dppipMinTxSlots
The minimum number of slots per DTM frame that can be
allocated at the DPP-IP transmit interface.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.8
dppipMaxTolJitter
The maximum tolerated jitter that can be configured expressed
in units of DPP-IP inter-frame intervals.

The DPP-IP inter-frame interval in microseconds is:
dppipRxSlotsPerFrame * 125 / dppipRxSlots.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.9
dppipMinTolJitter
The minimum tolerated jitter that can be configured expressed
in units of DPP-IP inter-frame intervals.

The DPP-IP inter-frame interval in microseconds is:
dppipRxSlotsPerFrame * 125 / dppipRxSlots.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.10
dppipDTSupport
The local interface's maximum level of support for the
Dynamic Trunk function.
DppipSupport
Type Constraints:
range: 2
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.11
dppipTTSupport
The local interface's maximum level of support for the Time
Transfer function.
DppipSupport
Type Constraints:
range: 2
 .1.3.6.1.4.1.2928.2.3.1.1.4.1.12

dppipPeerLimitsTable

table
.1.3.6.1.4.1.2928.2.3.1.1.5 · 1 row entry · 10 columns
Open in standard view
Uses the netinsight variant from /opt/observium/mibs/netinsight.
Command help
Walk dppipPeerLimitsTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'NETI-TRUNK-MIB' -M '/opt/observium/mibs/netinsight:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'NETI-TRUNK-MIB::dppipPeerLimitsTable' 
A list of DPP-IP interface limits entries.  The number of
entries is given by the value of dppipNumber.
dppipPeerLimitsEntry row .1.3.6.1.4.1.2928.2.3.1.1.5.1
A DPP-IP interface peer limits entry containing limits for the peer
of a particular interface.
Indexes
Column Syntax OID
dppipPeerMaxFecMode
The peer interface's maximum mode of operation of the Forward
Error Correction function (FEC).

The FEC function may be not used (fecNone), used for column
correction (fec1D) or used for both row and colum…
FecMode
Type Values:
1fecNone
2fec1D
3fec2D
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.1
dppipPeerMaxFecRows
The peer interface's maximum number of data rows in the
receive side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.2
dppipPeerMinFecRows
The peer interface's minimum number of data rows in the
receive side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.3
dppipPeerMaxFecCols
The peer interface's maximum number of data columns in the
receive side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.4
dppipPeerMinFecCols
The peer interface's minimum number of data columns in the
receive side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.5
dppipPeerMaxFecElems
The peer interface's maximum number of data elements in the
receive side Forward Error Correction (FEC) matrix.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.6
dppipPeerMaxRxSlots
The maximum number of slots per DTM frame that can be
allocated at the receive interface in the peer.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.7
dppipPeerMinRxSlots
The minimum number of slots per DTM frame that can be
allocated at the DPP-IP receive interface of the peer.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.8
dppipPeerDTSupport
The peer interface's maximum level of support for the Dynamic
Trunk function.
DppipSupport
Type Constraints:
range: 2
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.9
dppipPeerTTSupport
The peer interface's maximum level of support for the Time
Transfer function.
DppipSupport
Type Constraints:
range: 2
 .1.3.6.1.4.1.2928.2.3.1.1.5.1.10