MX-DHCP-MIB Table View

Subnets
          
This table configures the subnets of the DHCP server. The
NetworkInterfaceName parameter must match a network interface
that is Up and the EnableSubnet parameter must be set to
'Enable' to properly activate the DHCP server on that interface.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

subnetsEntry row .0.1900.1.100.1

A row in table Subnets.

Indexes

subnetsNetworkInterfaceName

Column	Syntax	OID
subnetsNetworkInterfaceName Network Interface Network interface on which the DHCP server is active. That interface must be up for the DHCP server to become active.	OctetString	.0.1900.1.100.1.100
subnetsEnableSubnet Enable Enables the subnet configuration. Activates the DHCP server on the subnet when enabled.	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.100.1.200
subnetsStartAddress Start Address Start address of the subnet range. It MUST be within the network interface's subnet.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.100.1.300
subnetsEndAddress End Address End address of the subnet range. It MUST be within the network interface's subnet and higher than or equal to the StartAddress value.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.100.1.400
subnetsAutomaticConfigurationInterface Configuration Interface The network interface that provides the automatic configuration (E.g.: DNS servers, NTP server, etc.) to this subnet.	OctetStringr/w Constraints: range: 0-50	.0.1900.1.100.1.450
subnetsConfigStatus Status Subnet configuration status. * Disabled: The EnableSubnet parameter is disabled or the NetworkInterfaceName parameter does not match a network interface that is Up. * Inv…	Enumeration Enumerated Values: 100 disabled 200 invalidConfig 300 ok	.0.1900.1.100.1.500
subnetsDelete Delete Deletes a row from the table.	Enumerationr/w Enumerated Values: 0 noOp 10 delete	.0.1900.1.100.1.600

Subnet Domain Names
          
This table specifies subnet-specific domain names
configurations. All subnets use the default configuration
unless the SpecificDomainNames.EnableConfig parameter is set
to 'Enable'.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificDomainNamesEntry row .0.1900.1.200.300.1

A row in table Subnet Domain Names.

Indexes

specificDomainNamesSubnetName

Column	Syntax	OID
specificDomainNamesSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.200.300.1.100
specificDomainNamesEnableConfig Enable Defines the domain name configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultDomainNameConfigSource and …	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.200.300.1.200
specificDomainNamesEnableOption Enable Option Enables the domain name (option 15).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.200.300.1.300
specificDomainNamesConfigSource Configuration Source Subnet's domain name specific configuration source. * HostConfiguration: The domain name is obtained from the host configuration. * Static: The domain name is s…	Enumerationr/w Enumerated Values: 200 hostConfiguration 400 static	.0.1900.1.200.300.1.400
specificDomainNamesStaticName Static Domain Name Static Domain Name Configuration. The SpecificDomainNames.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overrides the de…	MX-TCMxIpHostNamer/w Type Constraints: range: 0..255	.0.1900.1.200.300.1.500

Domain Names Information
          
This table contains the active subnets' domain names.

domainNamesInfoEntry row .0.1900.1.200.400.1

A row in table Domain Names Information.

Indexes

domainNamesInfoSubnetName

Column	Syntax	OID
domainNamesInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.200.400.1.100
domainNamesInfoDomainName Domain Name Indicates the subnet's current domain name.	OctetString	.0.1900.1.200.400.1.200

Subnet Lease Times
          
This table specifies subnet-specific lease times
configurations. All subnets use the default configuration
unless the SpecificLeaseTimes.EnableConfig parameter is set to
'Enable'.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificLeaseTimesEntry row .0.1900.1.300.200.1

A row in table Subnet Lease Times.

Indexes

specificLeaseTimesSubnetName

Column	Syntax	OID
specificLeaseTimesSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.300.200.1.100
specificLeaseTimesEnableConfig Enable Defines the lease time configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultLeaseTime parameter. * Ena…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.300.200.1.200
specificLeaseTimesLeaseTime Lease Time Specifies the subnet's specific lease time in seconds. This configuration overrides the default configuration set in the DefaultLeaseTime parameter when the SpecificLeaseTimes.En…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.0.1900.1.300.200.1.300

Lease Times
          
This table contains the active subnets' lease times.

leaseTimesInfoEntry row .0.1900.1.300.300.1

A row in table Lease Times.

Indexes

leaseTimesInfoSubnetName

Column	Syntax	OID
leaseTimesInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.300.300.1.100
leaseTimesInfoDefault Lease Time Indicates the subnet's current default lease time in seconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.0.1900.1.300.300.1.200

Subnet Default Routers
          
This table specifies subnet-specific default routers
configurations.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificDefaultRoutersEntry row .0.1900.1.400.100.1

A row in table Subnet Default Routers.

Indexes

specificDefaultRoutersSubnetName

Column	Syntax	OID
specificDefaultRoutersSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.400.100.1.100
specificDefaultRoutersEnableOption Enable Option Enables the default router (option 3).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.400.100.1.200
specificDefaultRoutersConfigSource Configuration Source The subnet's specific router configuration source. * HostInterface: The default router is the host address within the client's subnet. * Static: The default rou…	Enumerationr/w Enumerated Values: 100 hostInterface 400 static	.0.1900.1.400.100.1.300
specificDefaultRoutersStaticRouter Static Default Router Specifies the subnet's default router. The SpecificDefaultRouters.ConfigSource parameter must be set to 'Static' for this value to be applied.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.400.100.1.400

Default Routers
          
This table contains the active subnets' default routers.

defaultRoutersInfoEntry row .0.1900.1.400.200.1

A row in table Default Routers.

Indexes

defaultRoutersInfoSubnetName

Column	Syntax	OID
defaultRoutersInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.400.200.1.100
defaultRoutersInfoDefaultRouter Default Router Indicates the subnet's current default router.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.400.200.1.200

Static DNS Servers
          
This table contains the list of default static DNS servers for
all subnets. The DNS servers are sorted by priority. These DNS
servers are used as the current DNS servers when the Default
DnsServersConfigSource parameter is set to 'Static'.

defaultStaticDnsServersEntry row .0.1900.1.500.200.1

A row in table Static DNS Servers.

Indexes

defaultStaticDnsServersPriority

Column	Syntax	OID
defaultStaticDnsServersPriority Priority Priority number of this static DNS server. The lower the number is, the higher the priority is.	Unsigned32 Constraints: range: 1-4	.0.1900.1.500.200.1.100
defaultStaticDnsServersIpAddress IP Address Static DNS server's IP address.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.500.200.1.200

Subnet DNS Servers
          
This table specifies subnet-specific DNS servers
configurations. All subnets use the default configuration
unless the SpecificDnsServers.EnableConfig parameter is set to
'Enable'.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificDnsServersEntry row .0.1900.1.500.300.1

A row in table Subnet DNS Servers.

Indexes

specificDnsServersSubnetName

Column	Syntax	OID
specificDnsServersSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.500.300.1.100
specificDnsServersEnableConfig Enable Defines the DNS servers configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultDnsServersConfigSource and …	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.500.300.1.200
specificDnsServersEnableOption Enable Option Enables the DNS servers (option 6).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.500.300.1.300
specificDnsServersConfigSource Configuration Source DNS servers specific configuration source for the subnet. * HostConfiguration: The DNS servers are obtained from the host configuration. * Automatic: The DNS se…	Enumerationr/w Enumerated Values: 200 hostConfiguration 300 automatic 400 static	.0.1900.1.500.300.1.400
specificDnsServersStaticDns1 Static DNS 1 IP address of the first DNS server of the subnet. The SpecificDnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overrid…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.500.300.1.500
specificDnsServersStaticDns2 Static DNS 2 IP address of the second DNS server of the subnet. The SpecificDnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overri…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.500.300.1.600
specificDnsServersStaticDns3 Static DNS 3 IP address of the third DNS server of the subnet. The SpecificDnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overrid…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.500.300.1.700
specificDnsServersStaticDns4 Static DNS 4 IP address of the fourth DNS server of the subnet. The SpecificDnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overri…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.500.300.1.800

DNS Servers
          
This table contains the active subnets' DNS servers.

dnsServersInfoEntry row .0.1900.1.500.400.1

A row in table DNS Servers.

Indexes

dnsServersInfoSubnetName

Column	Syntax	OID
dnsServersInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.500.400.1.100
dnsServersInfoDns1 DNS 1 Indicates the subnets' first DNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.500.400.1.200
dnsServersInfoDns2 DNS 2 Indicates the subnets' second DNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.500.400.1.300
dnsServersInfoDns3 DNS 3 Indicates the subnets' third DNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.500.400.1.400
dnsServersInfoDns4 DNS 4 Indicates the subnets' fourth DNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.500.400.1.500

Static NTP Servers
          
This table contains the list of default static NTP servers for
all subnets. The NTP servers are sorted by priority. These NTP
servers are used as the current NTP servers when the
DefaultNtpServersConfigSource parameter is set to 'Static'.

defaultStaticNtpServersEntry row .0.1900.1.600.200.1

A row in table Static NTP Servers.

Indexes

defaultStaticNtpServersPriority

Column	Syntax	OID
defaultStaticNtpServersPriority Priority Priority number of this static NTP server. The lower the number is, the higher the priority is.	Unsigned32 Constraints: range: 1-4	.0.1900.1.600.200.1.100
defaultStaticNtpServersIpAddress IP Address NTP server's static IP address.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.600.200.1.200

Subnet NTP Servers
          
This table specifies subnet-specific NTP servers
configurations. All subnets use the default configuration
unless the SpecificNtpServers.EnableConfig parameter is set to
'Enable'.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificNtpServersEntry row .0.1900.1.600.300.1

A row in table Subnet NTP Servers.

Indexes

specificNtpServersSubnetName

Column	Syntax	OID
specificNtpServersSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.600.300.1.100
specificNtpServersEnableConfig Enable Defines the NTP servers configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultNtpServersConfigSource and …	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.600.300.1.200
specificNtpServersEnableOption Enable Option Enables the NTP servers (option 42).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.600.300.1.300
specificNtpServersConfigSource Configuration Source NTP servers specific configuration source for the subnet. * HostConfiguration: The NTP servers are obtained from the host configuration. * Automatic: The NTP se…	Enumerationr/w Enumerated Values: 200 hostConfiguration 300 automatic 400 static	.0.1900.1.600.300.1.400
specificNtpServersStaticNtp1 Static NTP 1 IP address of the first NTP server of the subnet. The SpecificNtpServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overrid…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.600.300.1.500
specificNtpServersStaticNtp2 Static NTP 2 IP address of the second NTP server of the subnet. The SpecificNtpServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overri…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.600.300.1.600
specificNtpServersStaticNtp3 Static NTP 3 IP address of the third NTP server of the subnet. The SpecificNtpServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overrid…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.600.300.1.700
specificNtpServersStaticNtp4 Static NTP 4 IP address of the fourth NTP server of the subnet. The SpecificNtpServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration overri…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.600.300.1.800

NTP Servers
          
This table contains the active subnets's NTP servers.

ntpServersInfoEntry row .0.1900.1.600.400.1

A row in table NTP Servers.

Indexes

ntpServersInfoSubnetName

Column	Syntax	OID
ntpServersInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.600.400.1.100
ntpServersInfoNtp1 NTP 1 Indicates the subnets' first NTP server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.600.400.1.200
ntpServersInfoNtp2 NTP 2 Indicates the subnets' second NTP server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.600.400.1.300
ntpServersInfoNtp3 NTP 3 Indicates the subnets' third NTP server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.600.400.1.400
ntpServersInfoNtp4 NTP 4 Indicates the subnets' fourth NTP server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.600.400.1.500

Static NBNS Servers
          
This table contains the list of default static NBNS servers
for all subnets. The NBNS servers are sorted by priority.

defaultStaticNbnsServersEntry row .0.1900.1.700.100.1

A row in table Static NBNS Servers.

Indexes

defaultStaticNbnsServersPriority

Column	Syntax	OID
defaultStaticNbnsServersPriority Priority Priority number of this static NBNS server. The lower the number is, the higher the priority is.	Unsigned32 Constraints: range: 1-4	.0.1900.1.700.100.1.100
defaultStaticNbnsServersIpAddress IP Address NBNS server's static IP address.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.700.100.1.200

Subnet NBNS Servers
          
This table specifies subnet-specific NBNS servers
configurations. All subnets use the default configuration
unless the SpecificNbnsServers.EnableConfig parameter is set
to 'Enable'.
          
The Dhcp.AddSubnet command may be used to add a new subnet to
the SubnetsTable and to all subnet-specific configuration
tables.

specificNbnsServersEntry row .0.1900.1.700.200.1

A row in table Subnet NBNS Servers.

Indexes

specificNbnsServersSubnetName

Column	Syntax	OID
specificNbnsServersSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.700.200.1.100
specificNbnsServersEnableConfig Enable Defines the NBNS servers configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultStaticNbnsServers.IpAddres…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.700.200.1.200
specificNbnsServersEnableOption Enable Option Enables the NBNS servers (option 44).	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.700.200.1.300
specificNbnsServersStaticNbns1 Static NBNS 1 IP address of the first NBNS server of the subnet. The SpecificNbnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration over…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.700.200.1.400
specificNbnsServersStaticNbns2 Static NBNS 2 IP address of the second NBNS server of the subnet. The SpecificNbnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration ove…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.700.200.1.500
specificNbnsServersStaticNbns3 Static NBNS 3 IP address of the third NBNS server of the subnet. The SpecificNbnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration over…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.700.200.1.600
specificNbnsServersStaticNbns4 Static NBNS 4 IP address of the fourth NBNS server of the subnet. The SpecificNbnsServers.ConfigSource parameter must be set to 'Static' for this value to be applied. This configuration ove…	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.700.200.1.700

NBNS Servers
          
This table contains the active subnets' NBNS servers.

nbnsServersInfoEntry row .0.1900.1.700.300.1

A row in table NBNS Servers.

Indexes

nbnsServersInfoSubnetName

Column	Syntax	OID
nbnsServersInfoSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.700.300.1.100
nbnsServersInfoNbns1 NBNS 1 Indicates the subnets' first NBNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.700.300.1.200
nbnsServersInfoNbns2 NBNS 2 Indicates the subnets' second NBNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.700.300.1.300
nbnsServersInfoNbns3 NBNS 3 Indicates the subnets' third NBNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.700.300.1.400
nbnsServersInfoNbns4 NBNS 4 Indicates the subnets' fourth NBNS server.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.700.300.1.500

Static Leases
          
This table specifies IP addresses that are reserved for specific
hosts.

staticLeasesEntry row .0.1900.1.800.1

A row in table Static Leases.

Indexes

staticLeasesMacAddress

Column	Syntax	OID
staticLeasesMacAddress MAC Address MAC address of the host.	OctetString	.0.1900.1.800.1.100
staticLeasesIpAddress IP Address The reserved IP address of the host.	MX-TC2MxIpAddrr/w Type Constraints: range: 0..15	.0.1900.1.800.1.200
staticLeasesDelete Delete Deletes a static lease from the table.	Enumerationr/w Enumerated Values: 0 noOp 10 delete	.0.1900.1.800.1.300

Assigned Leases
          
This table lists the IP addresses that are currently assigned.

assignedLeasesInfoEntry row .0.1900.1.900.1

A row in table Assigned Leases.

Indexes

assignedLeasesInfoIpAddress

Column	Syntax	OID
assignedLeasesInfoIpAddress IP Address IP Address of the host.	MX-TC2MxIpAddr Type Constraints: range: 0..15	.0.1900.1.900.1.100
assignedLeasesInfoMacAddress MAC Address MAC address of the host.	OctetString	.0.1900.1.900.1.200
assignedLeasesInfoSubnetName Subnet Name Indicates on which subnet the host is located.	OctetString	.0.1900.1.900.1.300
assignedLeasesInfoLeaseTimeLeft Lease Time Left Indicates the lease time left in seconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.0.1900.1.900.1.400

Specific Option 66
          
This table contains the Option 66 for each subnet.

specificOption66Entry row .0.1900.1.1000.1000.1

A row in table Specific Option 66.

Indexes

specificOption66SubnetName

Column	Syntax	OID
specificOption66SubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.1000.1000.1.100
specificOption66EnableConfig Enable Defines the Option 66 configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultStaticOption66 parameter. *…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.1000.1000.1.200
specificOption66EnableOption Enable Option Enables the option 66 on this subnet.	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.1000.1000.1.300
specificOption66Value Value Subnet's Option 66 specific value. This configuration overrides the default configuration set in the DefaultStaticOption66 parameter when the SpecificOption66.EnableConfig parameter i…	OctetStringr/w Constraints: range: 0-120	.0.1900.1.1000.1000.1.400

Specific Option 67
          
This table contains the Option 67 for each subnet. When empty,
option 67 is not sent.

specificOption67Entry row .0.1900.1.1000.1100.1

A row in table Specific Option 67.

Indexes

specificOption67SubnetName

Column	Syntax	OID
specificOption67SubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.1000.1100.1.100
specificOption67EnableConfig Enable Defines the Option 67 configuration to use for this specific subnet. * Disable: The subnet uses the default configuration as defined in the DefaultStaticOption67 parameter. *…	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.1000.1100.1.200
specificOption67EnableOption Enable Option Enables the option 67 on this subnet.	MX-TCMxEnableStater/w Type Values: 0 disable 1 enable	.0.1900.1.1000.1100.1.300
specificOption67Value Value Subnet's Option 67 specific value. This configuration overrides the default configuration set in the DefaultStaticOption67 parameter when the SpecificOption67.EnableConfig parameter i…	OctetStringr/w Constraints: range: 0-120	.0.1900.1.1000.1100.1.400

Statistics
          
This table contains the statistics for each
subnet.

subnetsStatsEntry row .0.1900.1.10000.100.1

A row in table Statistics.

Indexes

subnetsStatsSubnetName

Column	Syntax	OID
subnetsStatsSubnetName Subnet Name Name of the subnet.	OctetString	.0.1900.1.10000.100.1.100
subnetsStatsNumberOfLeases Number of Leases Number of currently assigned leases.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.0.1900.1.10000.100.1.200