MPLS-LDP-STD-MIB Table View

This table contains information about the
MPLS Label Distribution Protocol Entities which
exist on this Label Switching Router (LSR)
or Label Edge Router (LER).

mplsLdpEntityEntry row .1.3.6.1.2.1.10.166.4.1.2.3.1

An entry in this table represents an LDP entity.
An entry can be created by a network administrator
or by an SNMP agent as instructed by LDP.

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex

Column	Syntax	OID
mplsLdpEntityLdpId The LDP identifier.	MPLS-TC-STD-MIBMplsLdpIdentifier Type Constraints: range: 6	.1.3.6.1.2.1.10.166.4.1.2.3.1.1
mplsLdpEntityIndex This index is used as a secondary index to uniquely identify this row. Before creating a row in this table, the 'mplsLdpEntityIndexNext' object should be retrieved. That value should be used for the value of this index…	DIFFSERV-MIBIndexInteger Type Constraints: range: 1..4294967295	.1.3.6.1.2.1.10.166.4.1.2.3.1.2
mplsLdpEntityProtocolVersion The version number of the LDP protocol which will be used in the session initialization message. Section 3.5.3 in the LDP Specification specifies that the version of the LDP protocol is negotiated during …	Unsigned32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.3
mplsLdpEntityAdminStatus The administrative status of this LDP Entity. If this object is changed from 'enable' to 'disable' and this entity has already attempted to establish contact with a Peer, then all contact with that Peer is lost and all …	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.2.1.10.166.4.1.2.3.1.4
mplsLdpEntityOperStatus The operational status of this LDP Entity. The value of unknown(1) indicates that the operational status cannot be determined at this time. The value of unknown should be a transient condition before cha…	Enumeration Enumerated Values: 1 unknown 2 enabled 3 disabled	.1.3.6.1.2.1.10.166.4.1.2.3.1.5
mplsLdpEntityTcpPort The TCP Port for LDP. The default value is the well-known value of this port.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.6
mplsLdpEntityUdpDscPort The UDP Discovery Port for LDP. The default value is the well-known value for this port.	INET-ADDRESS-MIBInetPortNumberr/w Type Constraints: range: 0..65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.7
mplsLdpEntityMaxPduLength The maximum PDU Length that is sent in the Common Session Parameters of an Initialization Message. According to the LDP Specification [RFC3036] a value of 255 or less specifies the default maximum length of 4096 octets,…	octetsUnsigned32r/w Constraints: range: 256-65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.8
mplsLdpEntityKeepAliveHoldTimer The 16-bit integer value which is the proposed keep alive hold timer for this LDP Entity.	secondsUnsigned32r/w Constraints: range: 1-65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.9
mplsLdpEntityHelloHoldTimer The 16-bit integer value which is the proposed Hello hold timer for this LDP Entity. The Hello Hold time in seconds. An LSR maintains a record of Hellos received from potential peers. This object represe…	secondsUnsigned32r/w Constraints: range: 0-65535	.1.3.6.1.2.1.10.166.4.1.2.3.1.10
mplsLdpEntityInitSessionThreshold When attempting to establish a session with a given Peer, the given LDP Entity should send out the SNMP notification, 'mplsLdpInitSessionThresholdExceeded', when the number of Session Initialization messages sent exceed…	Integer32r/w Constraints: range: 0-100	.1.3.6.1.2.1.10.166.4.1.2.3.1.11
mplsLdpEntityLabelDistMethod For any given LDP session, the method of label distribution must be specified.	MPLS-TC-STD-MIBMplsLabelDistributionMethodr/w Type Values: 1 downstreamOnDemand 2 downstreamUnsolicited	.1.3.6.1.2.1.10.166.4.1.2.3.1.12
mplsLdpEntityLabelRetentionMode The LDP Entity can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be…	MPLS-TC-STD-MIBMplsRetentionModer/w Type Values: 1 conservative 2 liberal	.1.3.6.1.2.1.10.166.4.1.2.3.1.13
mplsLdpEntityPathVectorLimit If the value of this object is 0 (zero) then Loop Detection for Path Vectors is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors is enabled, and the Pa…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.166.4.1.2.3.1.14
mplsLdpEntityHopCountLimit If the value of this object is 0 (zero), then Loop Detection using Hop Counters is disabled. If the value of this object is greater than 0 (zero) then Loop Detection using Hop Counters is enabled, and thi…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.2.1.10.166.4.1.2.3.1.15
mplsLdpEntityTransportAddrKind This specifies whether the loopback or interface address is to be used as the transport address in the transport address TLV of the hello message. If the value is interface(1), then the IP address of the …	Enumerationr/w Enumerated Values: 1 interface 2 loopback	.1.3.6.1.2.1.10.166.4.1.2.3.1.16
mplsLdpEntityTargetPeer If this LDP entity uses targeted peer then set this to true.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.10.166.4.1.2.3.1.17
mplsLdpEntityTargetPeerAddrType The type of the internetwork layer address used for the Extended Discovery. This object indicates how the value of mplsLdpEntityTargetPeerAddr is to be interpreted.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.10.166.4.1.2.3.1.18
mplsLdpEntityTargetPeerAddr The value of the internetwork layer address used for the Extended Discovery. The value of mplsLdpEntityTargetPeerAddrType specifies how this address is to be interpreted.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.2.1.10.166.4.1.2.3.1.19
mplsLdpEntityLabelType Specifies the optional parameters for the LDP Initialization Message. If the value is generic(1) then no optional parameters will be sent in the LDP Initialization message associated with this Entity. …	MPLS-TC-STD-MIBMplsLdpLabelTyper/w Type Values: 1 generic 2 atm 3 frameRelay	.1.3.6.1.2.1.10.166.4.1.2.3.1.20
mplsLdpEntityDiscontinuityTime The value of sysUpTime on the most recent occasion at which any one or more of this entity's counters suffered a discontinuity. The relevant counters are the specific instances associated with this entity of any Counte…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.166.4.1.2.3.1.21
mplsLdpEntityStorageType The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.166.4.1.2.3.1.22
mplsLdpEntityRowStatus The status of this conceptual row. All writable objects in this row may be modified at any time, however, as described in detail in the section entitled, 'Changing Values After Session Establishment', and again describ…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.166.4.1.2.3.1.23

This table is a read-only table which augments
the mplsLdpEntityTable.  The purpose of this
table is to keep statistical information about
the LDP Entities on the LSR.

mplsLdpEntityStatsEntry row .1.3.6.1.2.1.10.166.4.1.2.4.1

A row in this table contains statistical information
about an LDP Entity. Some counters contained in a
row are for fatal errors received during a former
LDP Session associated with this entry. For example,
an LDP PDU …

Indexes

No indexes recorded

Column	Syntax	OID
mplsLdpEntityStatsSessionAttempts A count of the Session Initialization messages which were sent or received by this LDP Entity and were NAK'd. In other words, this counter counts the number of session initializations that failed. Disco…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.1
mplsLdpEntityStatsSessionRejectedNoHelloErrors A count of the Session Rejected/No Hello Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the management syst…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.2
mplsLdpEntityStatsSessionRejectedAdErrors A count of the Session Rejected/Parameters Advertisement Mode Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization o…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.3
mplsLdpEntityStatsSessionRejectedMaxPduErrors A count of the Session Rejected/Parameters Max Pdu Length Error Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initi…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.4
mplsLdpEntityStatsSessionRejectedLRErrors A count of the Session Rejected/Parameters Label Range Notification Messages sent or received by this LDP Entity. Discontinuities in the value of this counter can occur at re-initialization of the managem…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.5
mplsLdpEntityStatsBadLdpIdentifierErrors This object counts the number of Bad LDP Identifier Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.6
mplsLdpEntityStatsBadPduLengthErrors This object counts the number of Bad PDU Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-ini…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.7
mplsLdpEntityStatsBadMessageLengthErrors This object counts the number of Bad Message Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.8
mplsLdpEntityStatsBadTlvLengthErrors This object counts the number of Bad TLV Length Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-ini…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.9
mplsLdpEntityStatsMalformedTlvValueErrors This object counts the number of Malformed TLV Value Fatal Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at r…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.10
mplsLdpEntityStatsKeepAliveTimerExpErrors This object counts the number of Session Keep Alive Timer Expired Errors detected by the session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occ…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.11
mplsLdpEntityStatsShutdownReceivedNotifications This object counts the number of Shutdown Notifications received related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-init…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.12
mplsLdpEntityStatsShutdownSentNotifications This object counts the number of Shutdown Notfications sent related to session(s) (past and present) associated with this LDP Entity. Discontinuities in the value of this counter can occur at re-initializ…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.2.4.1.13

Information about LDP peers known by Entities in
the mplsLdpEntityTable.  The information in this table
is based on information from the Entity-Peer interaction
during session initialization but is not appropriate
for the mplsLdpSessionTable, because objects in this
table may or may not be used in session establishment.

mplsLdpPeerEntry row .1.3.6.1.2.1.10.166.4.1.3.2.1

Information about a single Peer which is related
to a Session. This table is augmented by
the mplsLdpSessionTable.

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId

Column	Syntax	OID
mplsLdpPeerLdpId The LDP identifier of this LDP Peer.	MPLS-TC-STD-MIBMplsLdpIdentifier Type Constraints: range: 6	.1.3.6.1.2.1.10.166.4.1.3.2.1.1
mplsLdpPeerLabelDistMethod For any given LDP session, the method of label distribution must be specified.	MPLS-TC-STD-MIBMplsLabelDistributionMethod Type Values: 1 downstreamOnDemand 2 downstreamUnsolicited	.1.3.6.1.2.1.10.166.4.1.3.2.1.2
mplsLdpPeerPathVectorLimit If the value of this object is 0 (zero) then Loop Dection for Path Vectors for this Peer is disabled. Otherwise, if this object has a value greater than zero, then Loop Dection for Path Vectors for this …	Integer32 Constraints: range: 0-255	.1.3.6.1.2.1.10.166.4.1.3.2.1.3
mplsLdpPeerTransportAddrType The type of the Internet address for the mplsLdpPeerTransportAddr object. The LDP specification describes this as being either an IPv4 Transport Address or IPv6 Transport Address which is used in opening…	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.10.166.4.1.3.2.1.4
mplsLdpPeerTransportAddr The Internet address advertised by the peer in the Hello Message or the Hello source address. The type of this address is specified by the value of the mplsLdpPeerTransportAddrType object.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.2.1.10.166.4.1.3.2.1.5

A table of Sessions between the LDP Entities
and LDP Peers.  This table AUGMENTS the
mplsLdpPeerTable.  Each row in this table
represents a single session.

mplsLdpSessionEntry row .1.3.6.1.2.1.10.166.4.1.3.3.1

An entry in this table represents information on a
single session between an LDP Entity and LDP Peer.
The information contained in a row is read-only.

Please note: the Path Vector Limit for the
Session is …

Indexes

No indexes recorded

Column	Syntax	OID
mplsLdpSessionStateLastChange The value of sysUpTime at the time this Session entered its current state as denoted by the mplsLdpSessionState object.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.166.4.1.3.3.1.1
mplsLdpSessionState The current state of the session, all of the states 1 to 5 are based on the state machine for session negotiation behavior.	Enumeration Enumerated Values: 1 nonexistent 2 initialized 3 openrec 4 opensent 5 operational	.1.3.6.1.2.1.10.166.4.1.3.3.1.2
mplsLdpSessionRole During session establishment the LSR/LER takes either the active role or the passive role based on address comparisons. This object indicates whether this LSR/LER was behaving in an active role or passive role during t…	Enumeration Enumerated Values: 1 unknown 2 active 3 passive	.1.3.6.1.2.1.10.166.4.1.3.3.1.3
mplsLdpSessionProtocolVersion The version of the LDP Protocol which this session is using. This is the version of the LDP protocol which has been negotiated during session initialization.	Unsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.166.4.1.3.3.1.4
mplsLdpSessionKeepAliveHoldTimeRem The keep alive hold time remaining for this session.	SNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.2.1.10.166.4.1.3.3.1.5
mplsLdpSessionKeepAliveTime The negotiated KeepAlive Time which represents the amount of seconds between keep alive messages. The mplsLdpEntityKeepAliveHoldTimer related to this Session is the value that was proposed as the KeepAlive Time for thi…	secondsUnsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.166.4.1.3.3.1.6
mplsLdpSessionMaxPduLength The value of maximum allowable length for LDP PDUs for this session. This value may have been negotiated during the Session Initialization. This object is related to the mplsLdpEntityMaxPduLength object. The mplsLdpE…	octetsUnsigned32 Constraints: range: 1-65535	.1.3.6.1.2.1.10.166.4.1.3.3.1.7
mplsLdpSessionDiscontinuityTime The value of sysUpTime on the most recent occasion at which any one or more of this session's counters suffered a discontinuity. The relevant counters are the specific instances associated with this session of any Coun…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.10.166.4.1.3.3.1.8

A table of statistics for Sessions between
LDP Entities and LDP Peers.  This table AUGMENTS
          
the mplsLdpPeerTable.

mplsLdpSessionStatsEntry row .1.3.6.1.2.1.10.166.4.1.3.4.1

An entry in this table represents statistical
information on a single session between an LDP
Entity and LDP Peer.

Indexes

No indexes recorded

Column	Syntax	OID
mplsLdpSessionStatsUnknownMesTypeErrors This object counts the number of Unknown Message Type Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management sys…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.3.4.1.1
mplsLdpSessionStatsUnknownTlvErrors This object counts the number of Unknown TLV Errors detected by this LSR/LER during this session. Discontinuities in the value of this counter can occur at re-initialization of the management system, and …	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.10.166.4.1.3.4.1.2

A table of Hello Adjacencies for Sessions.

mplsLdpHelloAdjacencyEntry row .1.3.6.1.2.1.10.166.4.1.3.5.1.1

Each row represents a single LDP Hello Adjacency.
An LDP Session can have one or more Hello
Adjacencies.

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId mplsLdpHelloAdjacencyIndex

Column	Syntax	OID
mplsLdpHelloAdjacencyIndex An identifier for this specific adjacency.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.2.1.10.166.4.1.3.5.1.1.1
mplsLdpHelloAdjacencyHoldTimeRem If the value of this object is 65535, this means that the hold time is infinite (i.e., wait forever). Otherwise, the time remaining for this Hello Adjacency to receive its next Hello Message. …	secondsSNMPv2-TCTimeInterval Type Constraints: range: 0..2147483647 Description: A period of time, measured in units of 0.01 seconds.	.1.3.6.1.2.1.10.166.4.1.3.5.1.1.2
mplsLdpHelloAdjacencyHoldTime The Hello hold time which is negotiated between the Entity and the Peer. The entity associated with this Hello Adjacency issues a proposed Hello Hold Time value in the mplsLdpEntityHelloHoldTimer object. The peer also…	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.2.1.10.166.4.1.3.5.1.1.3
mplsLdpHelloAdjacencyType This adjacency is the result of a 'link' hello if the value of this object is link(1). Otherwise, it is a result of a 'targeted' hello, targeted(2).	Enumeration Enumerated Values: 1 link 2 targeted	.1.3.6.1.2.1.10.166.4.1.3.5.1.1.4

A table of LDP LSP's which
map to the mplsInSegmentTable in the
MPLS-LSR-STD-MIB module.

mplsInSegmentLdpLspEntry row .1.3.6.1.2.1.10.166.4.1.3.6.1

An entry in this table represents information
on a single LDP LSP which is represented by
a session's index triple (mplsLdpEntityLdpId,
mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
index for the mplsInSegmentTable
(mpl…

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId mplsInSegmentLdpLspIndex

Column	Syntax	OID
mplsInSegmentLdpLspIndex This contains the same value as the mplsInSegmentIndex in the MPLS-LSR-STD-MIB's mplsInSegmentTable.	MPLS-LSR-STD-MIBMplsIndexType Type Constraints: range: 1..24	.1.3.6.1.2.1.10.166.4.1.3.6.1.1
mplsInSegmentLdpLspLabelType The Layer 2 Label Type.	MPLS-TC-STD-MIBMplsLdpLabelType Type Values: 1 generic 2 atm 3 frameRelay	.1.3.6.1.2.1.10.166.4.1.3.6.1.2
mplsInSegmentLdpLspType The type of LSP connection.	MPLS-TC-STD-MIBMplsLspType Type Values: 1 unknown 2 terminatingLsp 3 originatingLsp 4 crossConnectingLsp	.1.3.6.1.2.1.10.166.4.1.3.6.1.3

A table of LDP LSP's which
map to the mplsOutSegmentTable in the
MPLS-LSR-STD-MIB.

mplsOutSegmentLdpLspEntry row .1.3.6.1.2.1.10.166.4.1.3.7.1

An entry in this table represents information
on a single LDP LSP which is represented by
a session's index triple (mplsLdpEntityLdpId,
mplsLdpEntityIndex, mplsLdpPeerLdpId) AND the
index (mplsOutSegmentLdpLspIndex)
for…

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId mplsOutSegmentLdpLspIndex

Column	Syntax	OID
mplsOutSegmentLdpLspIndex This contains the same value as the mplsOutSegmentIndex in the MPLS-LSR-STD-MIB's mplsOutSegmentTable.	MPLS-LSR-STD-MIBMplsIndexType Type Constraints: range: 1..24	.1.3.6.1.2.1.10.166.4.1.3.7.1.1
mplsOutSegmentLdpLspLabelType The Layer 2 Label Type.	MPLS-TC-STD-MIBMplsLdpLabelType Type Values: 1 generic 2 atm 3 frameRelay	.1.3.6.1.2.1.10.166.4.1.3.7.1.2
mplsOutSegmentLdpLspType The type of LSP connection.	MPLS-TC-STD-MIBMplsLspType Type Values: 1 unknown 2 terminatingLsp 3 originatingLsp 4 crossConnectingLsp	.1.3.6.1.2.1.10.166.4.1.3.7.1.3

This table represents the FEC
(Forwarding Equivalence Class)
Information associated with an LSP.

mplsFecEntry row .1.3.6.1.2.1.10.166.4.1.3.8.3.1

Each row represents a single FEC Element.

Indexes

mplsFecIndex

Column	Syntax	OID
mplsFecIndex The index which uniquely identifies this entry.	DIFFSERV-MIBIndexInteger Type Constraints: range: 1..4294967295	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.1
mplsFecType The type of the FEC. If the value of this object is 'prefix(1)' then the FEC type described by this row is an address prefix. If the value of this object is 'hostAddress(2)' then the FEC type described b…	Enumerationr/w Enumerated Values: 1 prefix 2 hostAddress	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.2
mplsFecAddrPrefixLength If the value of the 'mplsFecType' is 'hostAddress(2)' then this object is undefined. If the value of 'mplsFecType' is 'prefix(1)' then the value of this object is the length in bits of the address prefix …	INET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.3
mplsFecAddrType The value of this object is the type of the Internet address. The value of this object, decides how the value of the mplsFecAddr object is interpreted.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.4
mplsFecAddr The value of this object is interpreted based on the value of the 'mplsFecAddrType' object. This address is then further interpretted as an being used with the address prefix, or as the host address. Thi…	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.5
mplsFecStorageType The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.6
mplsFecRowStatus The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified, except to set this object to 'destroy(6)'. NOTE: if this ro…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.166.4.1.3.8.3.1.7

A table which shows the relationship between
LDP LSPs and FECs.  Each row represents
a single LDP LSP to FEC association.

mplsLdpLspFecEntry row .1.3.6.1.2.1.10.166.4.1.3.10.1

An entry represents a LDP LSP
to FEC association.

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId mplsLdpLspFecSegment mplsLdpLspFecSegmentIndex mplsLdpLspFecIndex

Column	Syntax	OID
mplsLdpLspFecSegment If the value is inSegment(1), then this indicates that the following index, mplsLdpLspFecSegmentIndex, contains the same value as the mplsInSegmentLdpLspIndex. Otherwise, if the value of this object is …	Enumeration Enumerated Values: 1 inSegment 2 outSegment	.1.3.6.1.2.1.10.166.4.1.3.10.1.1
mplsLdpLspFecSegmentIndex This index is interpretted by using the value of the mplsLdpLspFecSegment. If the mplsLdpLspFecSegment is inSegment(1), then this index has the same value as mplsInSegmentLdpLspIndex. If th…	MPLS-LSR-STD-MIBMplsIndexType Type Constraints: range: 1..24	.1.3.6.1.2.1.10.166.4.1.3.10.1.2
mplsLdpLspFecIndex This index identifies the FEC entry in the mplsFecTable associated with this session. In other words, the value of this index is the same as the value of the mplsFecIndex that denotes the FEC associated with this Sessio…	DIFFSERV-MIBIndexInteger Type Constraints: range: 1..4294967295	.1.3.6.1.2.1.10.166.4.1.3.10.1.3
mplsLdpLspFecStorageType The storage type for this conceptual row. Conceptual rows having the value 'permanent(4)' need not allow write-access to any columnar objects in the row.	SNMPv2-TCStorageTyper/w Type Values: 1 other 2 volatile 3 nonVolatile 4 permanent 5 readOnly Description: Describes the memory realization of a conceptual row. A row which is volatile(2) is lost upon reboot. A row which is either nonVolatile(3), permanent(4) or readOnly(5), is backed up by stable storage. A row which is …	.1.3.6.1.2.1.10.166.4.1.3.10.1.4
mplsLdpLspFecRowStatus The status of this conceptual row. If the value of this object is 'active(1)', then none of the writable objects of this entry can be modified. The Agent should delete this row when the session ceases to…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.2.1.10.166.4.1.3.10.1.5

This table 'extends' the mplsLdpSessionTable.
This table is used to store Label Address Information
from Label Address Messages received by this LSR from
Peers.  This table is read-only and should be updated
          
when Label Withdraw Address Messages are received, i.e.,
Rows should be deleted as appropriate.
          
NOTE:  since more than one address may be contained
in a Label Address Message, this table 'sparse augments',
the mplsLdpSessionTable's information.

mplsLdpSessionPeerAddrEntry row .1.3.6.1.2.1.10.166.4.1.3.11.1

An entry in this table represents information on
a session's single next hop address which was
advertised in an Address Message from the LDP peer.
The information contained in a row is read-only.

Indexes

mplsLdpEntityLdpId mplsLdpEntityIndex mplsLdpPeerLdpId mplsLdpSessionPeerAddrIndex

Column	Syntax	OID
mplsLdpSessionPeerAddrIndex An index which uniquely identifies this entry within a given session.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.2.1.10.166.4.1.3.11.1.1
mplsLdpSessionPeerNextHopAddrType The internetwork layer address type of this Next Hop Address as specified in the Label Address Message associated with this Session. The value of this object indicates how to interpret the value of mplsLd…	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.2.1.10.166.4.1.3.11.1.2
mplsLdpSessionPeerNextHopAddr The next hop address. The type of this address is specified by the value of the mplsLdpSessionPeerNextHopAddrType.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.2.1.10.166.4.1.3.11.1.3