ME1200-QOS-MIB Table View

This table contains the configuration of WRED for queue 0 through 5

me1200QosWredEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1

Each row contains the configuration for a specific queue

Indexes

me1200QosWredQueue

Column	Syntax	OID
me1200QosWredQueue Queue index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1.1
me1200QosWredEnable If true, RED is enabled for this queue	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1.2
me1200QosWredMinimumFillLevel Controls the lower RED fill level threshold in percent of the whole queue. If the queue filling level is below this threshold, the drop probability is zero. Valid range is 0-100	ME1200-TCME1200Percentr/w Type Constraints: range: 0..100	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1.3
me1200QosWredMaximum Controls the upper RED drop probability or fill level threshold for frames marked with Drop Precedence Level 1 (yellow frames). Valid range is 1-100	ME1200-TCME1200Percentr/w Type Constraints: range: 0..100	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1.4
me1200QosWredMaxSelector Selects whether 'Maximum' controls 'Maximum Drop Probability' or 'Maximum Fill Level'.	ME1200MaxSelectorr/w Type Values: 0 maximumDropProbability 1 maximumFillLevel	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.2.1.5

This table has 64 entries, one for each DSCP value

me1200QosDscpEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1

Each row contains the configuration for a specific DSCP

Indexes

me1200QosDscpDscp

Column	Syntax	OID
me1200QosDscpDscp DSCP index.	DIFFSERV-DSCP-TCDscp Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.1
me1200QosDscpTrust If true, this DSCP value is trusted. Packets arriving on interfaces where 'TrustDscp' is enabled will be classified to the corresponding CoS and DPL in this table.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.2
me1200QosDscpCos The CoS value which the DSCP value maps to. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.3
me1200QosDscpDpl The DPL (Drop Precedence Level) which the DSCP value maps to. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.4
me1200QosDscpIngressTranslation The new classified DSCP value which the original DSCP value is replaced with if 'DscpTranslate' is enabled on the interface	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.5
me1200QosDscpClassify If true, then packets received on interfaces where 'DscpClassify' is set to 'selected' will be classified to a new DSCP value based on the classified CoS and DPL value configured in the qosCosDscpTable.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.6
me1200QosDscpEgressTranslation The new DSCP value that will be written into the packet at egress if 'DscpRemark' on the interface is set to 'remap' or 'remap-dp'. If 'remap-dp' is set then only packets classified to Dpl 0 will use this table.	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.7
me1200QosDscpEgressTranslationDp1 The new DSCP value that will be written into the packet at egress if 'DscpRemark' on the interface is set to 'remap-dp'. Only packets classified to Dpl 1 will use this table.	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.3.1.8

This table has QOS_CLASS_CNT entries, one for each Cos value

me1200QosCosToDscpEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.1.4.1

Each row contains the configuration for a specific Cos

Indexes

me1200QosCosToDscpCos

Column	Syntax	OID
me1200QosCosToDscpCos CoS index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.4.1.1
me1200QosCosToDscpDscp The DSCP value which the classified CoS value maps to when the classified DPL is 0.	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.4.1.2
me1200QosCosToDscpDscpDp1 The DSCP value which the classified CoS value maps to when the classified DPL is 1.	DIFFSERV-DSCP-TCDscpr/w Type Constraints: range: 0..63	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.4.1.3

This table contains the configuration of QCEs. The index is QceId.

me1200QosQceEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1

Each row contains the configuration of a single QCE.

Indexes

me1200QosQceQceId

Column	Syntax	OID
me1200QosQceQceId QCE Id index.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1
me1200QosQceNextQceId QCE Id of the next QCE.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.2
me1200QosQcePortList List of ports that are member of this QCE.	ME1200-TCME1200PortListr/w Type Constraints: range: 8	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.4
me1200QosQceDestMacType Indicates the destination MAC type to match.	ME1200DestMacTyper/w Type Values: 0 any 1 unicast 2 multicast 3 broadcast	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.5
me1200QosQceDestMac Indicates the 48 bits destination MAC address. The packets destination address is AND-ed with the value of DestMacMask and then compared against the value of this object. If this object value and the value of DestMacMas…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.6
me1200QosQceDestMacMask Indicates the 48 bits destination MAC address mask.Valid values are 00-00-00-00-00-00 or ff-ff-ff-ff-ff-ff.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.7
me1200QosQceSrcMac Indicates the 48 bits source MAC address. The packets source address is AND-ed with the value of SrcMacMask and then compared against the value of this object. If this object value and the value of SrcMacMask is 00-00-0…	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.8
me1200QosQceSrcMacMask Indicates the 48 bits source MAC address mask. Valid values are 00-00-00-00-00-00 or ff-ff-ff-ff-ff-ff.	SNMPv2-TCMacAddressr/w Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.9
me1200QosQceVlanTagType Indicates the VLAN tag type to match.	ME1200VlanTagTyper/w Type Values: 0 any 1 untagged 2 tagged 3 cTagged 4 sTagged	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.10
me1200QosQceVlanIdOp Indicates how a packets's VLAN ID is to be compared.	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.11
me1200QosQceVlanId The VLAN ID to be compared. If the VlanIdOp object in the same row is range(2), this object will be the starting VLAN ID of the range. Valid range is 1-4095. This object can only be configured if VlanIdOp is not any(0).	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.12
me1200QosQceVlanIdRange The VLAN ID to be compared. If the VlanIdOp object in the same row is range(2), this object will be the ending VLAN ID of the range. Valid range is 1-4095. This object can only be configured if VlanIdOp is range(2).	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.13
me1200QosQcePcp The PCP value(s) to be compared.	ME1200VlanTagPriorityr/w Type Values: 0 any 1 value0 2 value1 3 value2 4 value3 5 value4 6 value5 7 value6 8 value7 9 range0to1 10 range2to3 11 range4to5 12 range6to7 13 range0to3 14 range4to7	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.14
me1200QosQceDei The DEI value to be compared. Valid range is 0-1.	ME1200BitTyper/w Type Values: 0 any 1 zero 2 one	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.15
me1200QosQceInnerVlanTagType Indicates the inner VLAN tag type to match.	ME1200VlanTagTyper/w Type Values: 0 any 1 untagged 2 tagged 3 cTagged 4 sTagged	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.16
me1200QosQceInnerVlanIdOp Indicates how a packets's inner VLAN ID is to be compared.	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.17
me1200QosQceInnerVlanId The inner VLAN ID to be compared. If the InnerVlanIdOp object in the same row is range(2), this object will be the starting VLAN ID of the range. Valid range is 1-4095. This object can only be configured if InnerVlanIdO…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.18
me1200QosQceInnerVlanIdRange The inner VLAN ID to be compared. If the InnerVlanIdOp object in the same row is range(2), this object will be the ending VLAN ID of the range. Valid range is 1-4095. This object can only be configured if InnerVlanIdOp …	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.19
me1200QosQceInnerPcp The inner PCP value(s) to be compared.	ME1200VlanTagPriorityr/w Type Values: 0 any 1 value0 2 value1 3 value2 4 value3 5 value4 6 value5 7 value6 8 value7 9 range0to1 10 range2to3 11 range4to5 12 range6to7 13 range0to3 14 range4to7	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.20
me1200QosQceInnerDei The inner DEI value to be compared. Valid range is 0-1.	ME1200BitTyper/w Type Values: 0 any 1 zero 2 one	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.21
me1200QosQceFrameType Indicates the packet's frame type. Modifying the frame type on an existing QCE will restore the content of all frame type dependent configuration to default.	ME1200QceFrameTyper/w Type Values: 0 any 1 etype 2 llc 3 snap 4 ipv4 5 ipv6	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.100
me1200QosQceEtype Indicates the packet's 16 bit Ethernet type field. Valid values are: 0(match any), 0x600-0xFFFF but excluding 0x800(IPv4) and 0x86DD(IPv6).This object can only be configured if FrameType is etype(1).	ME1200-TCME1200EtherTyper/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.101
me1200QosQceLlcDsap Indicates the packets's 8 bit LLC DSAP field. The packets LLC DSAP field is AND-ed with the value of LlcDsapMask and then compared against the value of this object. If this object value and the value of LlcDsapMask is 0…	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.200
me1200QosQceLlcDsapMask Indicates the 8 bit LLC DSAP mask. Valid values are 0x00 or 0xFF. This object can only be configured if FrameType is llc(2).	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.201
me1200QosQceLlcSsap Indicates the packets's 8 bit LLC SSAP field. The packets LLC SSAP field is AND-ed with the value of LlcSsapMask and then compared against the value of this object. If this object value and the value of LlcSsapMask is 0…	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.202
me1200QosQceLlcSsapMask Indicates the 8 bit LLC SSAP mask. Valid values are 0x00 or 0xFF. This object can only be configured if FrameType is llc(2).	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.203
me1200QosQceLlcControl Indicates the packets's 8 bit LLC Control field. The packets LLC Control field is AND-ed with the value of LlcControlMask and then compared against the value of this object. If this object value and the value of LlcCont…	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.204
me1200QosQceLlcControlMask Indicates the 8 bit LLC Control mask. Valid values are 0x00 or 0xFF. This object can only be configured if FrameType is llc(2).	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.205
me1200QosQceSnapPid Indicates the packet's 16 bit SNAP PID field. The packets SNAP PID field is AND-ed with the value of SnapPidMask and then compared against the value of this object. If this object value and the value of SnapPidMask is 0…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.302
me1200QosQceSnapPidMask Indicates the 16 bit SNAP PID mask. Valid values are 0x0000 or 0xFFFF. This object can only be configured if FrameType is snap(3).	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.303
me1200QosQceIpv4Fragment Indicates how an IPv4 fragment bit is to be compared. This object can only be configured if FrameType is ipv4(4).	ME1200BitTyper/w Type Values: 0 any 1 zero 2 one	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.400
me1200QosQceIpv4DscpOp Indicates how an IPv4 DSCP field is to be compared. This object can only be configured if FrameType is ipv4(4).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.401
me1200QosQceIpv4Dscp The DSCP value to be compared. If the Ipv4DscpOp object in the same row is range(2), this object will be the starting DSCP value of the range. Valid range is 0-63. This object can only be configured if FrameType is ipv4…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.402
me1200QosQceIpv4DscpRange The DSCP value to be compared. If the Ipv4DscpOp object in the same row is range(2), this object will be the ending DSCP value of the range. Valid range is 0-63. This object can only be configured if FrameType is ipv4(4…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.403
me1200QosQceIpv4Protocol The protocol number field in the IPv4 header used to indicate a higher layer protocol. The packets protocol number field is AND-ed with the value of Ipv4ProtocolMask and then compared with the value of this object. If I…	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.404
me1200QosQceIpv4ProtocolMask The specified IPv4 protocol number mask. Valid values are 0 or 255. This object can only be configured if FrameType is ipv4(4).	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.405
me1200QosQceIpv4SrcIp The specified IPv4 source address. The packets source address is AND-ed with the value of Ipv4SrcIpMask and then compared with the value of this object. If Ipv4SrcIP and Ipv4SrcIpMask are 0.0.0.0, this entry matches any…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.406
me1200QosQceIpv4SrcIpMask The specified IPv4 source address mask. This object can only be configured if FrameType is ipv4(4).	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.407
me1200QosQceIpv4DestIp The specified IPv4 destination address. The packets destination address is AND-ed with the value of Ipv4DestIpMask and then compared with the value of this object. If Ipv4DestIP and Ipv4DestIpMask are 0.0.0.0, this entr…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.408
me1200QosQceIpv4DestIpMask The specified IPv4 destination address mask. This object can only be configured if FrameType is ipv4(4).	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.409
me1200QosQceIpv4SrcPortOp Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(4).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.410
me1200QosQceIpv4SrcPort The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.411
me1200QosQceIpv4SrcPortRange The source port number of the TCP or UDP protocol. If the Ipv4SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be c…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.412
me1200QosQceIpv4DestPortOp Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv4(4).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.413
me1200QosQceIpv4DestPort The destination port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can o…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.414
me1200QosQceIpv4DestPortRange The source port number of the TCP or UDP protocol. If the Ipv4DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be …	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.415
me1200QosQceIpv6DscpOp Indicates how an IPv6 DSCP field is to be compared. This object can only be configured if FrameType is ipv6(5).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.500
me1200QosQceIpv6Dscp The DSCP value to be compared. If the Ipv6DscpOp object in the same row is range(2), this object will be the starting DSCP value of the range. Valid range is 0-63. This object can only be configured if FrameType is ipv6…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.501
me1200QosQceIpv6DscpRange The DSCP value to be compared. If the Ipv6DscpOp object in the same row is range(2), this object will be the ending DSCP value of the range. Valid range is 0-63. This object can only be configured if FrameType is ipv6(5…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.502
me1200QosQceIpv6Protocol The protocol number field in the IPv6 header used to indicate a higher layer protocol. The packets protocol number field is AND-ed with the value of Ipv6ProtocolMask and then compared with the value of this object. If I…	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.503
me1200QosQceIpv6ProtocolMask The specified IPv6 protocol number mask. Valid values are 0 or 255. This object can only be configured if FrameType is ipv6(5).	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.504
me1200QosQceIpv6SrcIp The specified IPv6 source address. The packets source address is AND-ed with the value of Ipv6SrcIpMask and then compared with the value of this object. If Ipv6SrcIP and Ipv6SrcIpMask are all zeros, this entry matches a…	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.506
me1200QosQceIpv6SrcIpMask The specified IPv6 source address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(5).	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.508
me1200QosQceIpv6DestIp The specified IPv6 destination address. The packets destination address is AND-ed with the value of Ipv6DestIpMask and then compared with the value of this object. If Ipv6DestIP and Ipv6DestIpMask are all zeros, this en…	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.510
me1200QosQceIpv6DestIpMask The specified IPv6 destination address mask. Only the least significant 32 bits of this object are used. This object can only be configured if FrameType is ipv6(5).	INET-ADDRESS-MIBInetAddressIPv6r/w Type Constraints: range: 16	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.512
me1200QosQceIpv6SrcPortOp Indicates how a packet's source TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(5).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.513
me1200QosQceIpv6SrcPort The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can only be…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.514
me1200QosQceIpv6SrcPortRange The source port number of the TCP or UDP protocol. If the Ipv6SrcPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be c…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.515
me1200QosQceIpv6DestPortOp Indicates how a packet's destination TCP/UDP port number is to be compared. This object can only be configured if FrameType is ipv6(5).	ME1200ASRTyper/w Type Values: 0 any 1 specific 2 range	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.516
me1200QosQceIpv6DestPort The destination port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the starting port number of the port range. Valid range is 0-65535. This object can o…	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.517
me1200QosQceIpv6DestPortRange The source port number of the TCP or UDP protocol. If the Ipv6DestPortOp object in the same row is range(2), this object will be the ending port number of the port range. Valid range is 0-65535. This object can only be …	ME1200-TCME1200Unsigned16r/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.518
me1200QosQceActionCosEnable If true, the packet is classified to the CoS value in ActionCos.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1000
me1200QosQceActionCos The CoS value used for classification. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1001
me1200QosQceActionDplEnable If true, the packet is classified to the DPL value in ActionDpl.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1002
me1200QosQceActionDpl The DPL value used for classification. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1003
me1200QosQceActionDscpEnable If true, the packet is classified to the DSCP value in ActionDscp.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1004
me1200QosQceActionDscp The DSCP value used for classification. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1005
me1200QosQceActionPcpDeiEnable If true, the packet is classified to the PCP value in ActionPcp and the DEI value in ActionDei.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1006
me1200QosQceActionPcp The PCP value used for classification. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1007
me1200QosQceActionDei The DEI value used for classification. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1008
me1200QosQceActionPolicyEnable If true, the packet is classified to the policy number in ActionPolicy.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1009
me1200QosQceActionPolicy The policy number used for classification. Valid range is 0-63.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.1010
me1200QosQceAction Action	ME1200-TCME1200RowEditorStater/w	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.1.1.10000

This table contains the precedence of QCEs ordered by their position in
the QCL.

me1200QosQcePrecedenceEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.3.1

Each row contains the precedence of a single QCE.

Indexes

me1200QosQcePrecedenceIndex

Column	Syntax	OID
me1200QosQcePrecedenceIndex QCE precedence index. Indicates the position in QCL.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.3.1.1
me1200QosQcePrecedenceQceId QCE Id.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.1.10.3.1.2

This table provides QoS configuration for QoS manageable interfaces

me1200QosIfConfigEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1

Each row contains the configuration for a specific interface

Indexes

me1200QosIfConfigIfIndex

Column	Syntax	OID
me1200QosIfConfigIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.1
me1200QosIfConfigCos The default CoS value a packet is classified to. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.2
me1200QosIfConfigDpl The default DPL (Drop Precedence Level) a packet is classified to. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.3
me1200QosIfConfigPcp The default PCP value a packet is classified to. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.4
me1200QosIfConfigDei The default DEI value a packet is classified to. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.5
me1200QosIfConfigTrustTag If true and the packet is VLAN tagged, then the CoS and DPL assigned to the packet is the PCP and DEI value in the packet mapped to a CoS and DPL value defined in the qosTagToCosTable.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.6
me1200QosIfConfigTrustDscp If true and the packet type is IPv4 or IPv6 and the packet DSCP value is trusted in qosDscpTable, then the CoS and DPL assigned to the packet is the DSCP value in the packet mapped to a CoS and DPL value defined in the …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.7
me1200QosIfConfigDwrrCount The number of queues that are running Deficit Weighted Round Robin scheduling. This value is restricted to 0 or 6.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.8
me1200QosIfConfigTagRemarkingMode Selects the tag remarking mode for egress. Valid values are: 'classified' : Remark the tag with the classified values of PCP and DEI. 'default' : Remark the tag with the configured TagPcp a…	ME1200TagRemarkingModer/w Type Values: 0 classified 2 default 3 mapped	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.9
me1200QosIfConfigTagPcp The PCP value to put in the packet if TagRemarkingMode is set to 'default'. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.10
me1200QosIfConfigTagDei The DEI value to put in the packet if TagRemarkingMode is set to 'default'. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.11
me1200QosIfConfigDscpTranslate If true then the classified DSCP value is the DSCP value in the packed mapped to a new DSCP value defined in qosDscpTable.IngressTranslation.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.12
me1200QosIfConfigDscpClassify Selects if and how the classified DSCP is based on the classified CoS and DPL for IPv4 and IPv6 packets on ingress. If a packet is selected for being classified to a new DSCP, the classification in based …	ME1200DscpClassifyr/w Type Values: 0 none 1 zero 2 selected 3 all	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.13
me1200QosIfConfigDscpRemark Selects if and how the classified DSCP is written into the packet at egress. Valid values are: 'disabled' : Do not write the classified DSCP into the packet. 'rewrite' : Write the classifie…	ME1200DscpRemarkr/w Type Values: 0 disabled 1 rewrite 2 remap 3 remapDp	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.14
me1200QosIfConfigQceAddressMode If false, the QCE classification for this interface is based on source (SMAC/SIP) addresses. If true, the QCE classification for this interface is based on destination (DMAC/DIP) addresses. This parameter is only used w…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.15
me1200QosIfConfigQceKeyType The key type specifying the key generated for packets received on the interface. Valid values are: 'normal' : Half key, match outer tag, SIP and SMAC. 'double-tag' : Quarter key, match inne…	ME1200VcapKeyTyper/w Type Values: 0 normal 1 doubleTag 2 ipAddr 3 macIpAddr	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.1.1.16

This table contains the mapping of (interface, PCP, DEI) to (CoS, DPL)
values.The mappings given by this table is used for all tagged packets
received on an interface if and only if that interface has the value of
TrustTag set to 'true'

me1200QosIfTagToCosEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1

Each row contains the mapping from (interface, PCP, DEI) to (CoS, DPL)
values.

Indexes

me1200QosIfTagToCosIfIndex me1200QosIfTagToCosPcp me1200QosIfTagToCosDei

Column	Syntax	OID
me1200QosIfTagToCosIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1.1
me1200QosIfTagToCosPcp PCP index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1.2
me1200QosIfTagToCosDei DEI index.	Integer32 Constraints: range: 0-1	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1.3
me1200QosIfTagToCosCos The CoS value which this entry maps to. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1.4
me1200QosIfTagToCosDpl The DPL (Drop Precedence Level) value which this entry maps to. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.2.1.5

This table contains the mapping of (interface, CoS, DPL) to (PCP, DEI)
values.The mappings given by this table is used for packets transmitted
on an interface if and only if that interface has the value of
TagRemarkingMode set to 'mapped'

me1200QosIfCosToTagEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1

Each row contains the mapping from (interface, CoS, DPL) to (PCP, DEI)
values.

Indexes

me1200QosIfCosToTagIfIndex me1200QosIfCosToTagCos me1200QosIfCosToTagDpl

Column	Syntax	OID
me1200QosIfCosToTagIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1.1
me1200QosIfCosToTagCos CoS index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1.2
me1200QosIfCosToTagDpl DPL index.	Integer32 Constraints: range: 0-3	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1.3
me1200QosIfCosToTagPcp The PCP value which this entry maps to. Valid range is 0-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1.4
me1200QosIfCosToTagDei The DEI value which this entry maps to. Valid range is 0-1.	ME1200-TCME1200Unsigned8r/w Type Constraints: range: 0..255	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.3.1.5

This table provides policer configuration for an interface

me1200QosIfPolicerEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1

Each row contains the configuration for a specific policer

Indexes

me1200QosIfPolicerIfIndex

Column	Syntax	OID
me1200QosIfPolicerIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1.1
me1200QosIfPolicerEnable If true, the port policer is enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1.2
me1200QosIfPolicerFrameRate If true, the rate is measured in fps instead of kbps.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1.3
me1200QosIfPolicerFlowControl If true, and flow control is enabled on the interface, then issue flow control pause frames instead of discarding frames.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1.4
me1200QosIfPolicerCir Committed Information Rate. Measured in kbps if FrameRate is false and fps if FrameRate is true. Valid range is 100-3300000.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.4.1.5

This table provides queue policer configuration for interfaces

me1200QosIfQueuePolicerEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.5.1

Each row contains the configuration for a specific queue policer

Indexes

me1200QosIfQueuePolicerIfIndex me1200QosIfQueuePolicerQueue

Column	Syntax	OID
me1200QosIfQueuePolicerIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.5.1.1
me1200QosIfQueuePolicerQueue Queue index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.5.1.2
me1200QosIfQueuePolicerEnable If true, the queue policer is enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.5.1.3
me1200QosIfQueuePolicerCir Committed Information Rate. Measured in kbps. Valid range is 100-3300000.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.5.1.6

This table provides shaper configuration for an interface

me1200QosIfShaperEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.6.1

Each row contains the configuration for a specific shaper

Indexes

me1200QosIfShaperIfIndex

Column	Syntax	OID
me1200QosIfShaperIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.6.1.1
me1200QosIfShaperEnable If true, the port shaper is enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.6.1.2
me1200QosIfShaperCir Committed Information Rate. Measured in kbps. Valid range is 100-3300000.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.6.1.3

This table provides queue shaper configuration for interfaces

me1200QosIfQueueShaperEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1

Each row contains the configuration for a specific queue shaper

Indexes

me1200QosIfQueueShaperIfIndex me1200QosIfQueueShaperQueue

Column	Syntax	OID
me1200QosIfQueueShaperIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1.1
me1200QosIfQueueShaperQueue Queue index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1.2
me1200QosIfQueueShaperEnable If true, the queue shaper is enabled.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1.3
me1200QosIfQueueShaperExcess If true, then allow this queue to get a share of the excess bandwidth. Excess bandwidth is allowed if this shaper is closed and no other queues with open shapers have frames for transmission.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1.4
me1200QosIfQueueShaperCir Committed Information Rate. Measured in kbps. Valid range is 100-3300000.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.7.1.5

This table contains the mapping of (interface, queue) to weight
values.The mappings given by this table is used when an interface has
the value of DwrrCount greater than 0. Read the qosSchedulerStatusTable
in order to get the 'real' weights in percent as used by the hardware

me1200QosIfSchedulerEntry row .1.3.6.1.4.1.9.9.815.1.14.1.2.2.8.1

Each row contains the scheduler configuration for a specific queue.

Indexes

me1200QosIfSchedulerIfIndex me1200QosIfSchedulerQueue

Column	Syntax	OID
me1200QosIfSchedulerIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.8.1.1
me1200QosIfSchedulerQueue Queue index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.8.1.2
me1200QosIfSchedulerWeight The weight for this queue. Valid range is 1-100.	ME1200-TCME1200Percentr/w Type Constraints: range: 0..100	.1.3.6.1.4.1.9.9.815.1.14.1.2.2.8.1.3

This table contains the QCE status in the hardware table.

me1200QosStatusQceEntry row .1.3.6.1.4.1.9.9.815.1.14.1.3.1.1.1

Each row contains the status of a single QCE.

Indexes

me1200QosStatusQceIndex

Column	Syntax	OID
me1200QosStatusQceIndex QCE precedence index. Indicates the position in QCL.	Integer32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.3.1.1.1.2
me1200QosStatusQceUserId User Id.	ME1200QceUserType Type Values: 0 admin 1 voiceVlan	.1.3.6.1.4.1.9.9.815.1.14.1.3.1.1.1.3
me1200QosStatusQceQceId QCE Id.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.3.1.1.1.4
me1200QosStatusQceConflict If true, a resource conflict is detected.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.815.1.14.1.3.1.1.1.100

This table provides QoS status for QoS manageable interfaces

me1200QosStatusIfEntry row .1.3.6.1.4.1.9.9.815.1.14.1.3.2.1.1

Each row contains the status for a specific interface

Indexes

me1200QosStatusIfIfIndex

Column	Syntax	OID
me1200QosStatusIfIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.3.2.1.1.1
me1200QosStatusIfCos Some subsystems are allowed to modify the default CoS value for an interface. This object shows the actual default CoS value a packet is classified to.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.815.1.14.1.3.2.1.1.2

This table contains the mapping of (interface, queue) to weight
values.The mappings given by this table are the 'real' weights in
percent as used by the hardware

me1200QosStatusIfSchedulerEntry row .1.3.6.1.4.1.9.9.815.1.14.1.3.2.2.1

Each row contains the scheduler status for a specific queue.

Indexes

me1200QosStatusIfSchedulerIfIndex me1200QosStatusIfSchedulerQueue

Column	Syntax	OID
me1200QosStatusIfSchedulerIfIndex Logical interface index.	ME1200-TCME1200InterfaceIndex Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.9.9.815.1.14.1.3.2.2.1.1
me1200QosStatusIfSchedulerQueue Queue index.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.9.9.815.1.14.1.3.2.2.1.2
me1200QosStatusIfSchedulerWeight The weight for this queue. Valid range is 1-100.	ME1200-TCME1200Percent Type Constraints: range: 0..100	.1.3.6.1.4.1.9.9.815.1.14.1.3.2.2.1.3