LUM-IFBASIC-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
55

ifBasicIfTable

table
.1.3.6.1.4.1.8708.2.46.2.2.1 · 1 row entry · 7 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifBasicIfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFBASIC-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFBASIC-MIB::ifBasicIfTable' 
The if basic if interface list.
ifBasicIfEntry row .1.3.6.1.4.1.8708.2.46.2.2.1.1
An entry in the ifBasic if list.
Indexes
Column Syntax OID
ifBasicIfIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.1
ifBasicIfName
The management name of the interface, for example
'client:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.2
ifBasicIfTxSignalStatus
The state for outgoing (TX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.3
ifBasicIfRxSignalStatus
The state for incoming (RX) signal
of the interface.

down - A major fault has occurred.

degraded - The signal quality is impaired.

up - The signal is OK.
LUM-TCSignalStatusWithNA
Type Values:
1down
2degraded
3up
2147483647notApplicable
Description:
SignalStatus.
notApplicable - used to tell that attribute
is not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.4
ifBasicIfUpId
Identity in the UP for the interface. The upId is used internally between CU and
TU to define a certain interface in the TU.
Unsigned32
Constraints:
range: 0-2147483647
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.5
ifBasicIfAid
The access identifier (AID) of the interface.
The format is according to GR-833.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.6
ifBasicIfPhysicalLocation
The physical location of the if.
The format is according to GR-833.
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.46.2.2.1.1.7

ifBasicAdminTable

table
.1.3.6.1.4.1.8708.2.46.2.3.1 · 1 row entry · 15 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifBasicAdminTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFBASIC-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFBASIC-MIB::ifBasicAdminTable' 
The if basic admin interface list.
ifBasicAdminEntry row .1.3.6.1.4.1.8708.2.46.2.3.1.1
An entry in the ifBasic admin list.
Indexes
Column Syntax OID
ifBasicAdminIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.1
ifBasicAdminName
The management name of the interface, for example
'admin:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.2
ifBasicAdminDescr
User configurable label.
LUM-TCDisplayStringWithNAr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.3
ifBasicAdminSubrack
The subrack of the physical port that this interface is bound to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.4
ifBasicAdminSlot
The slot of the physical port that this interface is bound to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.5
ifBasicAdminTxPort
The transmitting physical port that this interface is bound to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.6
ifBasicAdminRxPort
The receiving physical port that this interface is bound to.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.7
ifBasicAdminAdminStatus
The administrative state of the ifBasic interface.

down - The interface is de-activated.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or r…
LUM-TCAdminStatusWithNAr/w
Type Values:
1down
2service
3up
2147483647notApplicable
Description:
The administrative state for an interface.

down - The interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
service or re-confi…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.8
ifBasicAdminOperStatus
The operational state for the interface.

notPresent - The interface is not available.

down - The interface is de-activated or there are
faults preventing its transition to the 'up' state.
…
LUM-TCOperStatusWithNA
Type Values:
1notPresent
2down
3up
2147483647notApplicable
Description:
The operational state for a interface.

notPresent - The interface is not available.

down - The interface is de-activated or
there are faults preventing it from going to the
'up'-state.

u…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.9
ifBasicAdminAutoAlarmEnableStatus
The state of auto alarm enable for the interface.

suppressTrxAndSignal - Both signal alarms and trx alarms are suppressed
suppressSignal - Only signal alarms are suppressed
suppressNone -…
LUM-TCAutoAlarmStatus
Type Values:
1suppressTrxAndSignal
2suppressSignal
3suppressNone
2147483647notApplicable
Description:
The auto alarm enable function is in state
suppressTrxSignal, suppressSignal, suppressNone
or not Applicable.

suppressTrxAndSignal - Both signal alarms and trx alarms are suppressed
suppressSignal - O…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.10
ifBasicAdminAutoAlarmEnableReset
When the attribute is set to reset the auto-alarm enable function
is re-initialised. Then the attribute is set to normal again
automatically.

reset - Re-initialises the auto-alarm enable function
…
LUM-TCResetWithNA
Type Values:
1reset
2normal
2147483647notApplicable
Description:
When the attribute is set to reset the function is
re-initialised. Then the attribute is set to normal again
automatically.
reset - Re-initialises the function
normal - The function is in normal state
notApplicable - us…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.11
ifBasicAdminInterfaceStatus
The status of the traffic interface.

outOfService - No PM and no alarms.
autoInService - No PM and no alarms. Changes to 'inService' when OK.
inService - Reports PM and alarms.
maintenance …
LUM-TCInterfaceStatus
Type Values:
1outOfService
2autoInService
3inService
4maintenance
2147483647notApplicable
Description:
The traffic port status calculated dynamically from
auto alarm enbale status and admin status.

outOfService - No PM and no alarms.
autoInService - No PM and no alarms. Changes to 'inService' when OK.
inS…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.12
ifBasicAdminIfNo
The physical interface number of the actual multi-connector port.
LUM-TCUnsigned32WithNAr/w
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.13
ifBasicAdminIfType
Type of interface (Individual or bundled).
LUM-TCInterfaceTyper/w
Type Values:
1individual
2bundled
3bundledSplit
2147483646notAvailable
2147483647notApplicable
Description:
Indicates the type of interface.

individual - The ports of the interface are handled individually

bundled - The ports of the interface are bundled

bundledSplit - The ports of the …
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.14
ifBasicAdminNotAvailableForUse
Is the interface not available for use.
The interface may be created in order to show some
physical properties but may otherwise be unavailable
for service depending on setup and available resources.
LUM-TCTruthValueWithNA
Type Values:
0true
1false
2147483646notAvailable
2147483647notApplicable
Description:
Defines a value that can be true, false or not available

true - The condition is false

false - The condition is not true

notAvailable (2147483646) is used when attribute is
…
 .1.3.6.1.4.1.8708.2.46.2.3.1.1.15

ifBasicSignalTable

table
.1.3.6.1.4.1.8708.2.46.2.4.1 · 1 row entry · 33 columns
Open in standard view
Uses the infinera variant from /opt/observium/mibs/infinera.
Command help
Walk ifBasicSignalTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-IFBASIC-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-IFBASIC-MIB::ifBasicSignalTable' 
The if basic signal interface list.
ifBasicSignalEntry row .1.3.6.1.4.1.8708.2.46.2.4.1.1
An entry in the ifBasic signal list.
Indexes
Column Syntax OID
ifBasicSignalIndex
An index assigned to each entry.
SNMPv2-SMIUnsigned32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.1
ifBasicSignalName
The management name of the interface, for example
'signal:1:2:1-2', where the first number indicates
subrack, the second slot number and the third/fourth
are the physical port numbers.
LUM-TCMgmtNameString
Type Constraints:
range: 0..255
Description:
An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.2
ifBasicSignalSignalStructure
The signal structure used. Bitfield 64 bit wide. For internal use.
Bit 0 tells if mib ifBasicPhysicalTrx is loaded,
bit 1 ifBasicOpticalTranssection, etc according to list below.
Add new items last.
ifPhysicalTrx
if…
SNMPv2-SMICounter64
Type Constraints:
range: 0..18446744073709551615
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.3
ifBasicSignalSignalFormat
The signal format.
LUM-TCSignalFormatr/w
Type Values:
1other
2stm1
3stm4
4stm16
5gbE
6stm64
7fc1Gb
8fc2Gb
9wan10GbE
10unused
11lan10GbE
12escon
13esconLL
14dvb270
15oc3
16oc12
17oc48
18oc192
19hdtv1485
20ethernet
21fastEthernet
22lan10GbEFec
23wan10GbEStm64Fec
24fc4Gb
25etr
26auto
27down
28stm1Oc3
29stm4Oc12
30stm16Oc48
31stm64Oc192
32gbe9Line
34ddgbeLine
35gbEorTrm5500
36fc8Gb
37otu2
38otu2e
39e1
40t1
41mbh2Gb5
42syncE
43line4G
44mbh4Gbps
45fecLan10GbE1A
46fecLan10GbE1B
47sdi3G
48iWdm4G
49sdSdi270
50hdtvNTSC
51oc768
52stm256
53lan40GbE
54wan40GbE
55sfStm256Oc768
56iwdm40Gb
57otu4
58lan100GbE
59transpLan10GbE
60cpri1
61cpri2
62cpri3
63cpri4
64cpri5
65cpri6
66cpri7
67fc10Gb
68fc16Gb
69cpri8
70obsai1x
71obsai2x
72obsai4x
73obsai8x
74otu1
75iwdm11G
76rw100G
77rw200G
78otu4SdFec
79otuj1
80otuj2
81fc32Gb
82clearChannel32GbFc
83lan400GbE
84flexO4
85flexO2
86openZRplus400
87openZRplus200
88lan25GbE
89otuC2
90otuC4
91otuC1i
92otuC2i
93otuC1ix2
94otuC4i
95otuC1ix4
2147483647notApplicable
Description:
Signal format for an interfaces.

other - Unspecified format (see bitrate configuration
for speed)

stm1 - STM-1 SDH signal

stm4 - STM-4 SDH signal

stm16 - STM-16 SDH signal
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.4
ifBasicSignalFarEndLoopbackTerminatingLayer
The layer where the far end loopback (a.k.a.
terminal loopback for a client interface and
facility loopback for a line interface) is done.
This is coded in a bitmask
LUM-TCLayer
Type Constraints:
range: 0..2147483647
Description:
Layer in signal. this is a bitmask describing
layer. 2147483647 is used to indicate that the
attribute is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.5
ifBasicSignalFarEndLoopback
The far end loopback (a.k.a. terminal loopback for
a client interface and facility loopback for a line
interface) setting.

disabled - Far end loopback is not set. This is the
default setting.
…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.6
ifBasicSignalFarEndLoopbackTimeout
Timeout for far end loopback (a.k.a. terminal
loopback for a client interface and facility
loopback for a line interfac) to make sure
connection to node is not lost if ppp link is
broken. The unit is minutes. The value …
LUM-TCTime7200minr/w
Type Constraints:
range: 0..7200
range: 2147483647
Description:
An Integer32 of an object between 0 and 7200.
The value 0 is used in SNMP to indicate that the
setting will last forever.
2147483647 is used to indicate that the attribute
is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.7
ifBasicSignalNearEndLoopbackTerminatingLayer
The layer where the near end loopback (a.k.a.
terminal loopback for a line interface and facility
loopback for a client interface) is done.
This is coded in a bitmask.
LUM-TCLayer
Type Constraints:
range: 0..2147483647
Description:
Layer in signal. this is a bitmask describing
layer. 2147483647 is used to indicate that the
attribute is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.8
ifBasicSignalNearEndLoopback
The near end loopback (a.k.a. terminal
loopback for a line interface and facility loopback
for a client interface) setting.

disabled - Near end loopback is not set. This is the
default setting.
…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.9
ifBasicSignalNearEndLoopbackTimeout
Timeout for near end loopback (a.k.a. terminal
loopback for a line interface and facility loopback
for a client interface) to make sure connection to
node is not lost if ppp link is broken. The unit is
minutes. The valu…
LUM-TCTime7200minr/w
Type Constraints:
range: 0..7200
range: 2147483647
Description:
An Integer32 of an object between 0 and 7200.
The value 0 is used in SNMP to indicate that the
setting will last forever.
2147483647 is used to indicate that the attribute
is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.10
ifBasicSignalFarEndLoopbackEnabled
Far end end loopback (a.k.a. terminal loopback for
a client interface and facility loopback for a line
interface) is enabled.

alarm: Far end loopback is enabled.

ok: Far end loopback is dis…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.11
ifBasicSignalNearEndLoopbackEnabled
Near end end loopback (a.k.a. terminal loopback for
a line interface and facility loopback for a client
interface) is enabled.

alarm: Near end loopback is enabled.

ok: Near end loopback is …
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.12
ifBasicSignalOpticalLayerMapping
The optical layer mapping.
LUM-TCOpticalLayerMappingTyper/w
Type Values:
0undefined
1fourOpticalLanes
2tenOpticalLanes
3singleOpticalChannel
4eightOpticalLanes
Description:
Type of optical layer mapping.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.13
ifBasicSignalConfigurationMismatchdeprecated
The inserted transceiver does not support the
configuration of the optical layer mapping.

alarm: A transceiver with other supported optical layer
mapping than the requested mapping is inserted.
…
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.14
ifBasicSignalActualOpticalLayerMapping
The actual optical layer mapping.
LUM-TCOpticalLayerMappingType
Type Values:
0undefined
1fourOpticalLanes
2tenOpticalLanes
3singleOpticalChannel
4eightOpticalLanes
Description:
Type of optical layer mapping.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.15
ifBasicSignalSpeed
The expected signal bit rate in units of
10,000 bits (0.01 Mb) per second.
LUM-TCUnsigned32WithNAr/w
Constraints:
range: 61440-1402500
range: 2147483647-2147483647
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.16
ifBasicSignalDirection
The direction in which this object is
referred to.

rx - In bound direction. (1)

tx - out bound direction. (2)

biDir - the interface has one connector used for both rx a…
LUM-TCSignalDirection
Type Values:
1rx
2tx
3biDir
4txRx
2147483646notAvailable
Description:
Indicates the direction of the signal.

rx - Inbound direction

tx - Outbound direction

biDir - Bidirectional

txRx - Both Tx and Rx
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.17
ifBasicSignalFormatConfigurable
This atttribute indicates if the interface is format configurable or not

true - The interface is format configurable

false - The interface is not format configurable
Enumeration
Enumerated Values:
1true
2false
2147483647notApplicable
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.18
ifBasicSignalFormatConfigurationSharedWithInterface
This attribute specifies whether this object instances shares the format
configuration with another object instance.
value == 0: it is not shared
value != 0: it is shared with the interface object with index = val…
LUM-TCUnsigned32WithNA
Type Constraints:
range: 0..4294967294
Description:
An unsigned32 integer of an object.

4294967293 used to tell that it is not
possible to read attribute at the moment.

4294967294 is used to indicate that the attribute
is not used on the object
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.19
ifBasicSignalPhysicalLayerMapping
The expected physical layer mapping.
LUM-TCPhysicalLayerMappingTyper/w
Type Values:
1dualFiber
2singleFiber
Description:
Type of physical layer mapping.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.20
ifBasicSignalFacilityLoopback
The facility loopback setting. Rx is looped to Tx.
The purpose of facility loopback is to test
the line interface termination.

disabled - Facility loopback is not set. This is the
default setting.
…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.21
ifBasicSignalFacilityLoopbackTimeout
Timeout for facility loopback to make sure
connection to node is not lost if ppp link is
broken. The unit is minutes.

Note! This attribute is not saved in backup,
meaning the loopback will be set to disab…
LUM-TCTime7200minNo0r/w
Type Constraints:
range: 1..7200
range: 2147483647
Description:
An Integer32 of an object between 1 and 7200.
The value 2147483647 is used to indicate that
the attribute is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.22
ifBasicSignalFacilityLoopbackEnabled
Facility loopback is enabled.

alarm: Facility loopback is enabled.

ok: Facility loopback is disabled.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.23
ifBasicSignalTerminalLoopback
The terminal loopback setting. Tx is looped to Rx.
The purpose of a terminal loopback is to test
the path through the equipment (a cross-connect,
mux/demux stage, or similar) and execute the loop
close to the outgoing i…
LUM-TCEnabledDisabledWithNAr/w
Type Values:
1disabled
2enabled
2147483647notApplicable
Description:
disabled - Attribute is not set.

enabled - Attribute is set.

notApplicable (2147483647) is used when attribute is
not used in current configuration.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.24
ifBasicSignalTerminalLoopbackTimeout
Timeout for terminal loopback to make sure connection to
node is not lost if ppp link is broken. The unit is
minutes.

Note! This attribute is not saved in backup,
meaning the loopback will be set to disab…
LUM-TCTime7200minNo0r/w
Type Constraints:
range: 1..7200
range: 2147483647
Description:
An Integer32 of an object between 1 and 7200.
The value 2147483647 is used to indicate that
the attribute is not used on the object.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.25
ifBasicSignalTerminalLoopbackEnabled
Terminal loopback is enabled.

alarm: Terminal loopback is enabled.

ok: Terminal loopback is disabled.
LUM-TCFaultStatusWithNA
Type Values:
1ok
2alarm
2147483647notApplicable
Description:
A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.26
ifBasicSignalConnectorType
The connector type.
LUM-TCConnectorType
Type Values:
1connector4x10Gb
2connector1x100Gb
3connector3x32Gb
2147483647notApplicable
Description:
Connector type specifies the mode in which a port containing sub ports (henceforth referred to as
a main port) shall operate in. An example is the QSFP+/28 interface which can use
break-out QSFP optics in the same physi…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.27
ifBasicSignalSignalInformation
Signal information.
SNMPv2-TCDisplayStringr/w
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.28
ifBasicSignalInterleaverMode
Defines the interleaver mode.

xtm - Legacy mode used in XTM family. Interleaver mode is disabled.

nonXtm - Used for interoperability with other Infinera products, e.g. Groove/mTera. Interle…
LUM-TCInterleaverModer/w
Type Values:
0xtm
1nonXtm
Description:
Defines the interleaver mode
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.29
ifBasicSignalServiceTopology
Service topology of the XR module.

p2p - XR module used in point to point mode.

p2mp - XR Module used in point to multipoint (break-out) mode.
LUM-TCModelOptionr/w
Type Values:
1p2p
2p2mp
Description:
Services using XR pluggables.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.30
ifBasicSignalPointToMultipointRole
Service role when XR modules used in point-to-multipoint (P2MP) mode.

hub - XR Hub role, should be able to serve up to 4 Leaf modules with 100G service each.

leaf - XR Leaf role, should be …
LUM-TCServiceRoler/w
Type Values:
1hub
2leaf
Description:
Service role.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.31
ifBasicSignalFiberMode
Type of physical layer mapping used with the XR module.

dualFiber - Dual fiber mode.

singleFiber - Single fiber mode.

Note! using single fiber with XR, the total capacity of …
LUM-TCPhysicalLayerMappingTyper/w
Type Values:
1dualFiber
2singleFiber
Description:
Type of physical layer mapping.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.32
ifBasicSignalSingleFiberModeSide
Used sub-spectrum part in a single fiber mode.

a - Side A of the sub-spectrum is used.

b - Side B of the sub-spectrum is used.
LUM-TCSubspectrumr/w
Type Values:
1a
2b
2147483647notApplicable
Description:
Subspectrum parts.
 .1.3.6.1.4.1.8708.2.46.2.4.1.1.33