LUM-AUX-MIB Table View

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.2.1.1.2

auxSnmpDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.2.1.1.3

auxSnmpAddress

The IP address for the SNMP
managed equipment.

Type Constraints:
range: 4

.1.3.6.1.4.1.8708.2.29.2.2.1.1.4

auxSnmpVersion

SNMP protocol version.

Enumerationr/w

Enumerated Values:

1	v1
2	v2c

.1.3.6.1.4.1.8708.2.29.2.2.1.1.5

auxSnmpPort

The port number for the
SNMP managed equipment.

Unsigned32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.8708.2.29.2.2.1.1.6

auxSnmpReadCommunity

The community string to use when
reading information from the SNMP
managed equipment.

OctetStringr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.8708.2.29.2.2.1.1.7

auxSnmpWriteCommunity

The community string to use when
configuring the SNMP managed equipment.

OctetStringr/w

Constraints:
range: 0-255

.1.3.6.1.4.1.8708.2.29.2.2.1.1.8

auxSnmpAdminStatus

The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…

Type Values:

1	down
2	service
3	up

Description:

The administrative state for a board or
interface.

down - The board/interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
servi…

.1.3.6.1.4.1.8708.2.29.2.2.1.1.9

auxSnmpOperStatus

The operational state for the object.

notPresent - The HW related to the object
is not available

down - The object is de-activated or there are
faults preventing it from going to the 'up'-s…

auxSnmpInvPhysIndexOrZero

Type Values:

1	notPresent
2	down
3	up

Description:

The operational state for a board or interface.

notPresent - The board/interface is not available.

down - The board/interface is de-activated or
there are faults preventing it from going to the
'up…

.1.3.6.1.4.1.8708.2.29.2.2.1.1.10

The row in the invPhysTable for this interface.
Set to 0 if not known.

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.2.1.1.11

auxSnmpHostUnreachable

Can not contact the remote external equipment.
Check address and community strings.

A(ctivation): Contact lost

D(e-activation): Contact stablished again

Type Values:

1	ok
2	alarm

Description:

A value indicating the current state
of a potential fault condition leading to
an alarm for an object.

ok - indicates that no fault condition is present
and no alarm is active or the alarm has been cleared.
…

.1.3.6.1.4.1.8708.2.29.2.2.1.1.12

auxSnmpSnmpError

Can not login to the remote external equipment

A(ctivation): Contact lost

D(e-activation): Contact stablished again

auxSnmpUnexpectedEquipmentType

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.2.1.1.13

The remote external equipment is not of the
expected type.

A(ctivation): Wrong equipment detected

D(e-activation): Expected equipment detected

auxSnmpInconsistentConfiguration

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.2.1.1.14

Changes in the configuration of the remote
equipment has been detected.

This could happen if some other SNMP-manager
is manipulating the configuration, or the
configuration is changed via some local CLI.
…

auxSnmpConfigurationProblem

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.2.1.1.15

The SNMP-manager can not configure the remote
equipment.

A possible cause could be that the writeCommunity
does not match the remote equipment.

A(ctivation): A number of consecutive write
…

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.2.1.1.16

auxFxIfTable

table

.1.3.6.1.4.1.8708.2.29.2.3.1 · 1 row entry · 14 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxFxIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxFxIfTable'

The list of OAS modules.

auxFxIfEntry row .1.3.6.1.4.1.8708.2.29.2.3.1.1

An entry in the OAS module list.

Indexes

auxFxIfIndex

Column Syntax OID

auxFxIfIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.3.1.1.1

auxFxIfName

The name of the FxIf.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.2

auxFxIfDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.3.1.1.3

auxFxIfSubrack

The number of the subrack where the interface
is located.

Type Constraints:
range: 0..15

Description:

The number of a subrack within a network element.

0 signifies an undefined subrack number.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.4

auxFxIfSlot

The number of the slot where the interface is
located.

Type Constraints:
range: 0..22

Description:

The number of a slot within a subrack.

0 signifies an undefined slot number.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.5

auxFxIfTxPort

The number of the port where the interface is
located.

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.6

auxFxIfRxPort

The number of the port where the interface is
located.

auxFxIfInvPhysIndexOrZero

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.7

The row in the invPhysTable for this interface.
Set to 0 if not known.

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.3.1.1.8

auxFxIfAdminStatus

The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…

Type Values:

1	down
2	service
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.3.1.1.9

auxFxIfOperStatus

The operational state for the interface.

notPresent - The interface is not available.

down - The interface is de-activated or there are
faults preventing it from going to the 'up'-state.
…

Type Values:

1	notPresent
2	down
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.3.1.1.10

auxFxIfRxPowerLevel

The received power level in units of 0.1 dBm.

auxFxIfLossOfSignalThreshold

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.3.1.1.11

The lower threshold for received power level in
units of 0.1 dBm.

Note: Depending on the type of board and interface
the value range may vary.

Integer32r/w

Constraints:
range: -350--60

.1.3.6.1.4.1.8708.2.29.2.3.1.1.12

auxFxIfLossOfSignal

Loss of signal.
Applicable for all signal formats.

A(ctivation): Active loss of signal HW indication.

D(e-activation): Inactive loss of signal HW
indication.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.3.1.1.13

auxFxIfObjectProperty

Property mask.

Type Constraints:
range: 0..4294967295

Description:

A bitmask of length 32 encoding certain properties
of an object.

.1.3.6.1.4.1.8708.2.29.2.3.1.1.14

auxEquipmentTable

table

.1.3.6.1.4.1.8708.2.29.2.4.1 · 1 row entry · 17 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxEquipmentTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxEquipmentTable'

The list of OAS modules.

auxEquipmentEntry row .1.3.6.1.4.1.8708.2.29.2.4.1.1

An entry in the OAS module list.

Indexes

auxEquipmentIndex

Column Syntax OID

auxEquipmentIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.4.1.1.1

auxEquipmentName

The name of the equipment.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.4.1.1.2

auxEquipmentDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.4.1.1.3

auxEquipmentSubrack

The number of the subrack where the interface
is located.

Type Constraints:
range: 0..15

Description:

The number of a subrack within a network element.

0 signifies an undefined subrack number.

.1.3.6.1.4.1.8708.2.29.2.4.1.1.4

auxEquipmentSlot

The number of the slot where the interface is
located.

Type Constraints:
range: 0..22

Description:

The number of a slot within a subrack.

0 signifies an undefined slot number.

.1.3.6.1.4.1.8708.2.29.2.4.1.1.5

auxEquipmentAdminStatus

The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…

Type Values:

1	down
2	service
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.6

auxEquipmentOperStatus

The operational state for the interface.

notPresent - The interface is not available.

down - The interface is de-activated or there are
faults preventing it from going to the 'up'-state.
…

Type Values:

1	notPresent
2	down
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.7

auxEquipmentPowerFailure

Remote equipment reports power failure.

A(ctivation): Power failure detected

D(e-activation): Power failure no longer active

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.8

auxEquipmentFanProblem

Remote equipment report problem with built-in
fan unit.

A(ctivation): Fan problem detected

D(e-activation): Fan problem no longer active

auxEquipmentObjectProperty

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.9

Property mask

Type Constraints:
range: 0..4294967295

Description:

A bitmask of length 32 encoding certain properties
of an object.

.1.3.6.1.4.1.8708.2.29.2.4.1.1.10

auxEquipmentPumpsEol

Shows the end-of-life status of the HW.

For the RAMAN, the alarm is active if the
current of any of the pumps has reached its
end-of-life threshold.

auxEquipmentSelfTestFailure

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.11

Indicates if the built-in self-test
failed.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.12

auxEquipmentAmbientTemp

Shows the ambient temperature of the
equipment.

auxEquipmentRebootEquipment

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.4.1.1.13

Executing this procedure will initiate a reboot
of the auxiliary equipment.

auxEquipmentPowerAMissing

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.4.1.1.14

Status of 1U Power A missing Alarm.

auxEquipmentPowerBMissing

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.15

Status of 1U Power B missing Alarm.

auxEquipmentConfigurationMismatch

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.16

A configuration request has failed and there might now be a mismatch in configuration between tm3000 and external system.

A: A configuration request failed.

D: The configuration is re-sent …

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.4.1.1.17

auxRamanIfTable

table

.1.3.6.1.4.1.8708.2.29.2.5.1 · 1 row entry · 52 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxRamanIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxRamanIfTable'

The list of RAMAN i/f.

auxRamanIfEntry row .1.3.6.1.4.1.8708.2.29.2.5.1.1

An entry in the RAMAN i/f list.

Indexes

auxRamanIfIndex

Column Syntax OID

auxRamanIfIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.1

auxRamanIfName

The name of the FxIf.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.2

auxRamanIfDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.5.1.1.3

auxRamanIfSubrack

The number of the subrack where the interface
is located.

Type Constraints:
range: 0..15

Description:

The number of a subrack within a network element.

0 signifies an undefined subrack number.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.4

auxRamanIfSlot

The number of the slot where the interface is
located.

Type Constraints:
range: 0..22

Description:

The number of a slot within a subrack.

0 signifies an undefined slot number.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.5

auxRamanIfTxPort

The number of the port where the interface is
located.

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.6

auxRamanIfRxPort

The number of the port where the interface is
located.

auxRamanIfInvPhysIndexOrZero

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.7

The row in the invPhysTable for this interface.
Set to 0 if not known.

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.8

auxRamanIfAdminStatus

The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…

Type Values:

1	down
2	service
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.9

auxRamanIfOperStatus

The operational state for the interface.

notPresent - The interface is not available.

down - The interface is de-activated or there are
faults preventing it from going to the 'up'-state.
…

Type Values:

1	notPresent
2	down
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.10

auxRamanIfObjectProperty

Property mask.

auxRamanIfModuleOperationMode

Type Constraints:
range: 0..4294967295

Description:

A bitmask of length 32 encoding certain properties
of an object.

.1.3.6.1.4.1.8708.2.29.2.5.1.1.11

Module operational mode.

Enumeration

Enumerated Values:

1	coPropagating
2	counterPropagating

.1.3.6.1.4.1.8708.2.29.2.5.1.1.12

auxRamanIfPumpsOperationMode

Pumps operational mode.

Enumerationr/w

Enumerated Values:

1	maxPumpsPower
2	manualPumpsPower
3	automaticalGainControl

.1.3.6.1.4.1.8708.2.29.2.5.1.1.13

auxRamanIfPumpsOperationModeConfig

Configure pumps operational mode.

auxRamanIfAutoRestartProcTime

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.5.1.1.14

auxRamanIfLineFiberType

Line fiber type (for adaptive
gain flattening).

Enumerationr/w

Enumerated Values:

1	ftSMF
2	ftLeaf
3	ftTrueWave
4	ftG654
5	ftTeralight
6	ftG653

.1.3.6.1.4.1.8708.2.29.2.5.1.1.15

Automatic Restart Procedure restart time.

Unsigned32r/w

Constraints:
range: 0-100

.1.3.6.1.4.1.8708.2.29.2.5.1.1.16

auxRamanIfArpPauseStatus

Shows whether the Raman amplifier is in
Automatic Restart Procedure restart
state.

Enumeration

Enumerated Values:

1	normal
2	pause

.1.3.6.1.4.1.8708.2.29.2.5.1.1.17

auxRamanIfPumpsStatus

Shows whether the pumps are active or not.

Enumeration

Enumerated Values:

1	shutdown
2	active

.1.3.6.1.4.1.8708.2.29.2.5.1.1.18

auxRamanIfTotalPumpsPower

The total power of the pumps.

auxRamanIfPump1WantedPower

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.19

The wanted power of the higher pump.
Used for manual configuration.

Unsigned32r/w

Constraints:
range: 100-4000

.1.3.6.1.4.1.8708.2.29.2.5.1.1.20

auxRamanIfPump1ActualPower

The actual power of the higher pump.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.21

auxRamanIfPump1Current

The current of the higher pump.

auxRamanIfPump1Temperature

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.8708.2.29.2.5.1.1.22

The temperature of the higher pump.

auxRamanIfPump2WantedPower

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.23

The wanted power of the higher pump.
Used for manual configuration.

Unsigned32r/w

Constraints:
range: 100-4000

.1.3.6.1.4.1.8708.2.29.2.5.1.1.24

auxRamanIfPump2ActualPower

The actual power of the higher pump.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.25

auxRamanIfPump2Current

The current of the higher pump.

auxRamanIfPump2Temperature

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.8708.2.29.2.5.1.1.26

The temperature of the higher pump.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.27

auxRamanIfWantedGain

The wanted gain.
Used in gain-mode.

Unsigned32r/w

Constraints:
range: 30-200

.1.3.6.1.4.1.8708.2.29.2.5.1.1.28

auxRamanIfActualGain

The actual gain.
Used in gain-mode.

auxRamanIfReceivedPowerLevel

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.8708.2.29.2.5.1.1.29

The received power on the line i/f.

auxRamanIfReflectionPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.30

The received reflection power.

auxRamanIfReflectionPowerRatio

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.31

The received reflection power in relation
to the power of the pumps.

auxRamanIf1510BandReceivedPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.32

The received power in the 1510 band.

auxRamanIfOscReceivedPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.33

The received power of the OSC channel.

auxRamanIfLineLossOfSignal

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.34

auxRamanIfAPRState

Shows the state of the Automatic
Power Reduction procedure

Enumeration

Enumerated Values:

1	normal
2	shutdown

.1.3.6.1.4.1.8708.2.29.2.5.1.1.35

auxRamanIfOscDitherState

Shows the dithering state of the
Optical Supervisiory Channel.

Enumeration

Enumerated Values:

1	normal
2	lost

.1.3.6.1.4.1.8708.2.29.2.5.1.1.36

The input line signal is lost.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.37

auxRamanIfOscDitherLos

The dithering of the OSC channel is lost.

auxRamanIfHighBackReflection

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.38

High back-reflection power detected.

auxRamanIfHighLineOutputPower

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.39

High line output power is detected.
The power is decreased not to exceed
the maximum power

auxRamanIfLowLineOutputPower

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.40

Low output power is detected.

auxRamanIfModuleTempTooHigh

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.41

Too high ambient temperature of the amplifier
module causing shut down.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.42

auxRamanIfModuleTempHigh

High ambient temperature of the amplifier module.
Crossed warning threshold

auxRamanIfPumpsTempTooHigh

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.43

Too high temperature of the pumps causing
shut down.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.44

auxRamanIfPumpsTempHigh

High temperature of the pumps.
Crossed warning threshold.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.45

auxRamanIfAprShutdown

Shows if the pumps have been shutdown
according to any of the APR or ALS
schemes.

auxRamanIfLineFiberDeteriorated

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.46

The quality of the line fiber has
changed (deteriorated).

auxRamanIf1510BandPowerLos

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.47

The power of the 1510 band has been lost.

auxRamanIfManualRestartTrial

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.5.1.1.48

Executing this procedure initiates a manual
restart trial.

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.5.1.1.49

auxRamanIfModuleTemp

Shows the ambient temperature of the
amplifier module.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.5.1.1.50

auxRamanIfTxSignalStatus

The operational state for outgoing (TX) signal
of the interface.

down - A fault that would lead to a protection
switch has occurred.

degraded - The signal quality is impaired.
…

Enumeration

Enumerated Values:

1	down
2	degraded
3	up

.1.3.6.1.4.1.8708.2.29.2.5.1.1.51

auxRamanIfRxSignalStatus

The operational state for incoming (RX) signal
of the interface.

down - A major fault has occurred

degraded - The signal quality is impaired.

up - The signal is OK.

Enumeration

Enumerated Values:

1	down
2	degraded
3	up

.1.3.6.1.4.1.8708.2.29.2.5.1.1.52

auxRamanSafetyTable

table

.1.3.6.1.4.1.8708.2.29.2.6.1 · 1 row entry · 31 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxRamanSafetyTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxRamanSafetyTable'

The list of safety modules.

auxRamanSafetyEntry row .1.3.6.1.4.1.8708.2.29.2.6.1.1

An entry in the safety list.

Indexes

auxRamanSafetyIndex

Column Syntax OID

auxRamanSafetyIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.6.1.1.1

auxRamanSafetyName

The name of the ramanSafety object.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.2

auxRamanSafetyDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.6.1.1.3

auxRamanSafetySubrack

The number of the subrack where the interface
is located.

Type Constraints:
range: 0..15

Description:

The number of a subrack within a network element.

0 signifies an undefined subrack number.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.4

auxRamanSafetySlot

The number of the slot where the interface is
located.

Type Constraints:
range: 0..22

Description:

The number of a slot within a subrack.

0 signifies an undefined slot number.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.5

auxRamanSafetyTxPort

The number of the port where the interface is
located.

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.6

auxRamanSafetyRxPort

The number of the port where the interface is
located.

auxRamanSafetyInvPhysIndexOrZero

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.7

The row in the invPhysTable for this interface.
Set to 0 if not known.

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.6.1.1.8

auxRamanSafetyObjectProperty

Property mask.

auxRamanSafetyShutDownAtInputLoss

Type Constraints:
range: 0..4294967295

Description:

A bitmask of length 32 encoding certain properties
of an object.

.1.3.6.1.4.1.8708.2.29.2.6.1.1.9

This parameter controls whether the
amplifier will shut down in the following
situation:

Loss of input power

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.10

auxRamanSafetyShutDownAtHighTemp

This parameter controls whether the
amplifier will shut down in the following
situation:

The temperature of the pumps or the
modules is high.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.11

auxRamanSafetyShutDownAtHighBackReflection

This parameter controls whether the
amplifier will shut down in the following
situation:

There is a high back reflection of power,
indication that there might be a fibre
break.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.12

auxRamanSafetyHighBackReflectionThreshold

The threshold for back reflection
causing amplifier pumps to shut down.

The threshold is a ratio expressed in
dB relative to the output power of the
amplifier.

Integer32r/w

Constraints:
range: -28--19

.1.3.6.1.4.1.8708.2.29.2.6.1.1.13

auxRamanSafetyShutDownAtOscLoss

This parameter controls whether the
amplifier will shut down in the following
situation:

The signal from the OSC channel is lost.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.14

auxRamanSafetyShutDownAt1510BandDrop

This parameter controls whether the
amplifier will shut down in the following
situation:

The power from the 1510 band drops.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.15

auxRamanSafetyShutDownAtInputLossConfig

auxRamanSafetyShutDownAtHighTempConfig

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.16

auxRamanSafetyShutDownAtHighBackReflectionConfig

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.17

auxRamanSafetyShutDownAtOscLossConfig

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.18

auxRamanSafetyShutDownAt1510BandDropConfig

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.19

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.20

auxRamanSafetyPasswd

Password protecting the safety parameters

If password is '-' (dash), then the password
control is disabled.

auxRamanSafetyPasswdConfig

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.6.1.1.21

auxRamanSafety1510BandDropThreshold

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.22

The threshold for OSC band drop
causing pumps shut down.

Integer32r/w

Constraints:
range: 1-50

.1.3.6.1.4.1.8708.2.29.2.6.1.1.23

auxRamanSafetyInhibitStartAtOscLoss

This parameter controls whether the
amplifier is allowed to turn on in
a situation where the OSC is missing

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.24

auxRamanSafetyInhibitStartAtOscLossConfig

auxRamanSafetyShutDownAtLowBandDrop

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.25

This parameter controls whether the
amplifier will shut down in the following
situation:

Low L-band scattering is detected.

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.26

auxRamanSafetyLowBandScatteringThreshold

The threshold for safety parameter 'Shut down
at L-band power drop'.

Integer32r/w

Constraints:
range: -450--250

.1.3.6.1.4.1.8708.2.29.2.6.1.1.27

auxRamanSafetyShutDownAtLowBandDropConfig

auxRamanSafetyAmplifierSwitch

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.28

Enable activating or disable of the pumps operation.
When switch in Enabled mode,
pumps are activated to last operation mode
and power/current/gain settings

Enumerationr/w

Enumerated Values:

1	disabled
2	enabled

.1.3.6.1.4.1.8708.2.29.2.6.1.1.29

auxRamanSafetyAmplifierSwitchConfig

auxRamanSafetyLowBandScatteringTolerance

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.6.1.1.30

The transient tolerance (expressed in dB) for safety parameter
'Shut down at L-band drop'.

Integer32r/w

Constraints:
range: 10-20

.1.3.6.1.4.1.8708.2.29.2.6.1.1.31

auxPEIfTable

table

.1.3.6.1.4.1.8708.2.29.2.7.1 · 1 row entry · 35 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxPEIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxPEIfTable'

The list of PE i/f.

auxPEIfEntry row .1.3.6.1.4.1.8708.2.29.2.7.1.1

An entry in the PE i/f list.

Indexes

auxPEIfIndex

Column Syntax OID

auxPEIfIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.1

auxPEIfName

The name of the FxIf.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.2

auxPEIfDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.7.1.1.3

auxPEIfSubrack

The number of the subrack where the interface
is located.

Type Constraints:
range: 0..15

Description:

The number of a subrack within a network element.

0 signifies an undefined subrack number.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.4

auxPEIfSlot

The number of the slot where the interface is
located.

Type Constraints:
range: 0..22

Description:

The number of a slot within a subrack.

0 signifies an undefined slot number.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.5

auxPEIfTxPort

The number of the port where the interface is
located.

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.6

auxPEIfRxPort

The number of the port where the interface is
located.

auxPEIfInvPhysIndexOrZero

Type Constraints:
range: 0..116

Description:

The number of a port on a board.
If an interface has two numbers, the lowest number is used.

0 signifies an undefined port number.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.7

The row in the invPhysTable for this interface.
Set to 0 if not known.

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.8

auxPEIfAdminStatus

The administrative state for the interface.

down - The interface should be inactive.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-co…

Type Values:

1	down
2	service
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.9

auxPEIfOperStatus

The operational state for the interface.

notPresent - The interface is not available.

down - The interface is de-activated or there are
faults preventing it from going to the 'up'-state.
…

Type Values:

1	notPresent
2	down
3	up

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.10

auxPEIfObjectProperty

Property mask.

auxPEIfPumpsOperationMode

Type Constraints:
range: 0..4294967295

Description:

A bitmask of length 32 encoding certain properties
of an object.

.1.3.6.1.4.1.8708.2.29.2.7.1.1.11

In constant power mode the desired power has to be set.
In constant gain the desired output gain should be set.

Enumerationr/w

Enumerated Values:

1	constantPower
2	constantGain

.1.3.6.1.4.1.8708.2.29.2.7.1.1.12

auxPEIfPumpsOperationModeConfig

Configure pumps operational mode.
In constant power mode the desired power has to be set.
In constant gain mode the desired output gain should be set.

auxPEIfAutoRestartProcTime

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.7.1.1.13

Automatic Restart Procedure restart time.

Unsigned32r/w

Constraints:
range: 0-100

.1.3.6.1.4.1.8708.2.29.2.7.1.1.14

auxPEIfPumpsStatus

Shows whether the pumps are active or not.

Enumeration

Enumerated Values:

1	shutdown
2	active

.1.3.6.1.4.1.8708.2.29.2.7.1.1.15

auxPEIfWantedPower

Output power setting for constant power operation mode.

Integer32r/w

Constraints:
range: 100-261

.1.3.6.1.4.1.8708.2.29.2.7.1.1.16

auxPEIfWantedGain

Required gain value in dB for constant gain operation mode.

Unsigned32r/w

Constraints:
range: 50-90

.1.3.6.1.4.1.8708.2.29.2.7.1.1.17

auxPEIfPumpsTotalCurrent

Pumps total current

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.8708.2.29.2.7.1.1.18

auxPEIfPump1Temperature

The temperature of the higher pump.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.19

auxPEIfActualGain

The actual gain of the Amplifier (deci-dB).

auxPEIfReceivedPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.20

Input Power (Forward mode) (deci-dBm).
Please Note: Original value of Float type was transformed to an integer,
therefore the MIB value is presented in deci-dBm. (i.e. 50.5 dBm transformed to 505 deci-dBm).
Any EMS GUI …

auxPEIfCombinedOutPwrLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.21

Line Interface combined Output Power (deci-dBm).
Please Note: Original value of Float type was transformed to an integer,
therefore the MIB value is presented in deci-dBm. (i.e. 50.5 dBm transformed to 505 deci-dBm).
An…

auxPEIfReflectionPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.22

The received reflection power.

auxPEIfReflectionPowerRatio

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.23

The received reflection power in relation
to the power of the pumps.

auxPEIfLowBandScatteredPowerLevel

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.24

The scattered power in the L-band.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.25

auxPEIfLineLossOfSignal

The input line signal is lost.

auxPEIfHighBackReflection

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.26

High back-reflection power detected.

auxPEIfAutoPowerReduction

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.27

Automatic Power Reduction

auxPEIfLowLineOutputPower

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.28

Low output power is detected.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.29

auxPEIfModuleTempTooHigh

Too high ambient temperature of the amplifier
module causing shut down.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.30

auxPEIfModuleTempHigh

High ambient temperature of the amplifier module.
Crossed warning threshold

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.31

auxPEIfPumpsTempTooHigh

Too high temperature of the pumps causing
shut down.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.32

auxPEIfPumpsTempHigh

High temperature of the pumps.
Crossed warning threshold.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.7.1.1.33

auxPEIfModuleTemp

Shows the ambient temperature of the
amplifier module.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.34

auxPEIfPump2Temperature

Pump #2 temperature.

Type Constraints:
range: -2147483648..2147483647

.1.3.6.1.4.1.8708.2.29.2.7.1.1.35

auxNodeTable

table

.1.3.6.1.4.1.8708.2.29.2.8.1 · 1 row entry · 11 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxNodeTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxNodeTable'

The list of Node (TM2000) stuff.

auxNodeEntry row .1.3.6.1.4.1.8708.2.29.2.8.1.1

An entry in the Node list.

Indexes

auxNodeIndex

Column Syntax OID

auxNodeIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.8.1.1.1

auxNodeName

The name of the Node.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.8.1.1.2

auxNodeDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.8.1.1.3

auxNodeIpAddress

The IP address for the TM2000 node. The default value is set to 10.0.<subrack>.11 at system start-up.

Type Constraints:
range: 4

.1.3.6.1.4.1.8708.2.29.2.8.1.1.4

auxNodePort

The server port number for the TM2000 node.

Unsigned32r/w

Constraints:
range: 1024-65535

.1.3.6.1.4.1.8708.2.29.2.8.1.1.5

auxNodeEventPort

The event port number for the TM2000 node.

Unsigned32r/w

Constraints:
range: 1024-65535

.1.3.6.1.4.1.8708.2.29.2.8.1.1.6

auxNodeTime

The date and time of the TM2000 node.

SNMPv2-TCDateAndTime

Type Constraints:
range: 8
range: 11

Description:

A date-time specification.

field octets contents range
----- ------ -------- -----
1 1-2 year* 0..65536
2 3 month …

.1.3.6.1.4.1.8708.2.29.2.8.1.1.7

auxNodeNtpPrimary

The primary NTP Server address. This will
default be set to master CU IP address which
is 10.0.1.1.

Type Constraints:
range: 4

.1.3.6.1.4.1.8708.2.29.2.8.1.1.8

auxNodeNtpSecondary

The secondary NTP Server address.

Type Constraints:
range: 4

.1.3.6.1.4.1.8708.2.29.2.8.1.1.9

auxNodeChangeLocalTime

Change the local date and time.

Year - If no century is input the
current century is set by default.

Month - 1 to 12

Day - 1 to 31

Hour - 0 to 23
…

LUM-TCCommandStringr/w

Description:

tbd

.1.3.6.1.4.1.8708.2.29.2.8.1.1.10

auxNodeHostUnreachable

Can not contact the remote external equipment.
Check address and ports.

A(ctivation): Contact lost

D(e-activation): Contact established again

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.8.1.1.11

auxCabinetTable

table

.1.3.6.1.4.1.8708.2.29.2.9.1 · 1 row entry · 16 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxCabinetTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxCabinetTable'

The list of Cabinet stuff.

auxCabinetEntry row .1.3.6.1.4.1.8708.2.29.2.9.1.1

An entry in the Cabinet list.

Indexes

auxCabinetIndex

Column Syntax OID

auxCabinetIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.9.1.1.1

auxCabinetName

The name of the cabinet.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.9.1.1.2

auxCabinetDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.9.1.1.3

auxCabinetAdminStatus

The administrative state of the cabinet.

down - The interface is de-activated.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-configur…

LUM-TCAdminStatusWithNAr/w

Type Values:

1	down
2	service
3	up
2147483647	notApplicable

Description:

The administrative state for an interface.

down - The interface should be inactive.

service - The board/interface is activated but
alarms are suppressed. Intended for use during
service or re-confi…

.1.3.6.1.4.1.8708.2.29.2.9.1.1.4

auxCabinetOperStatus

Cabinet operational status

Enumeration

Enumerated Values:

1	notPresent
2	down
3	up

.1.3.6.1.4.1.8708.2.29.2.9.1.1.5

auxCabinetUpId

Identity in the UP for the auxCabinet entry in the traffic unit

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.9.1.1.6

auxCabinetIndoorTemp

The indoor temperature in the cabinet in 0.1 degrees centigrade.

LUM-TCSigned32WithNA

Type Constraints:
range: -2147483648..2147483647

Description:

A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently

.1.3.6.1.4.1.8708.2.29.2.9.1.1.7

auxCabinetOutdoorTemp

The outdoor temperature in the cabinet in 0.1 degrees centigrade.

LUM-TCSigned32WithNA

Type Constraints:
range: -2147483648..2147483647

Description:

A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently

.1.3.6.1.4.1.8708.2.29.2.9.1.1.8

auxCabinetOperMode

Cabinet operating mode

Enumeration

Enumerated Values:

0	off
1	cooling
2	heating
3	nightmode
4	tsf
5	selftest
6	manual

.1.3.6.1.4.1.8708.2.29.2.9.1.1.9

auxCabinetDoorAlarm

Alarm: The cabinet door is opened.

OK: The cabinet door is closed.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.10

auxCabinetSPDAlarm

Alarm: Surge Protection Device alarm.

OK: Surge Protection Device ok.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.11

auxCabinetHighTempAlarm

Alarm: Cabinet temperature too high.

OK: Cabinet temperature ok.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.12

auxCabinetCtrlFailAlarm

Alarm: Cabinet controller failure.

OK: Cabinet controller ok.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.13

auxCabinetHeatFailAlarm

Alarm: Cabinet heater failure.

OK: Cabinet heater ok.

auxCabinetExtTempFailAlarm

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.14

Alarm: Cabinet external temp sensor failure.

OK: Cabinet external temp sensor ok.

auxCabinetIntTempFailAlarm

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.15

Alarm: Cabinet internal temp sensor failure.

OK: Cabinet internal temp sensor ok.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.9.1.1.16

auxFanTable

table

.1.3.6.1.4.1.8708.2.29.2.10.1 · 1 row entry · 8 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxFanTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxFanTable'

A list of Fans.

auxFanEntry row .1.3.6.1.4.1.8708.2.29.2.10.1.1

An entry in the Fan list.

Indexes

auxFanIndex

Column Syntax OID

auxFanIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.10.1.1.1

auxFanName

The name of the fan.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.10.1.1.2

auxFanDescr

User configurable label.

Type Constraints:
range: 0..255

Description:

Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…

.1.3.6.1.4.1.8708.2.29.2.10.1.1.3

auxFanAdminStatus

The administrative state of the fan.

down - The interface is de-activated.

service - The interface is activated but alarms
are suppressed. Intended for use during service
or re-configuratio…

LUM-TCAdminStatusWithNAr/w

Type Values:

1	down
2	service
3	up
2147483647	notApplicable

Description:

.1.3.6.1.4.1.8708.2.29.2.10.1.1.4

auxFanOperStatus

Fan operational status

Enumeration

Enumerated Values:

1	notPresent
2	down
3	up

.1.3.6.1.4.1.8708.2.29.2.10.1.1.5

auxFanUpId

Identity in the UP for the auxFan entry in the traffic unit

Unsigned32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.8708.2.29.2.10.1.1.6

auxFanFailure

Alarm: The fan has failed.

OK: The fan is ok.

Type Values:

1	ok
2	alarm

Description:

.1.3.6.1.4.1.8708.2.29.2.10.1.1.7

auxFanRPM

The fan RPM.

LUM-TCSigned32WithNA

Type Constraints:
range: -2147483648..2147483647

Description:

A signed integer.

2147483646 used to tell that it is not
possible to read attribute at the moment.

2147483647 is used to indicate that the attri-
bute is not available currently

.1.3.6.1.4.1.8708.2.29.2.10.1.1.8

auxFanGroupTable

table

.1.3.6.1.4.1.8708.2.29.2.11.1 · 1 row entry · 7 columns

Open in standard view

Uses the infinera variant from /opt/observium/mibs/infinera.

Command help

Walk auxFanGroupTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'LUM-AUX-MIB' -M '/opt/observium/mibs/infinera:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'LUM-AUX-MIB::auxFanGroupTable'

A list of FanGroups.

auxFanGroupEntry row .1.3.6.1.4.1.8708.2.29.2.11.1.1

An entry in the FanGroup list.

Indexes

auxFanGroupIndex

Column Syntax OID

auxFanGroupIndex

An arbitrary index assigned to each
configuration equipment.

Unsigned32

Constraints:
range: 1-2147483647

.1.3.6.1.4.1.8708.2.29.2.11.1.1.1

auxFanGroupName

The name of the fan group.

Type Constraints:
range: 0..255

Description:

An octet string containing administrative
information, in human-readable form.

More or less the same as SnmpAdminString
defined in SNMP-FRAMEWORK-MIB.

.1.3.6.1.4.1.8708.2.29.2.11.1.1.2

auxFanGroupDescr

User configurable label.