LANTRONIX-SLC-MIB Table View

Table of Ethernet network entries.  The number of entries is 
given by the value of slcNetEthIfNumber.

slcNetEthIfEntry row .1.3.6.1.4.1.244.1.1.1.1.2.1

An entry with the attributes for each Ethernet interface. Ethernet
Port Eth1 is always index 1, and Eth2 is always index 2.

Indexes

slcNetEthIfIndex

Column	Syntax	OID
slcNetEthIfIndex Reference index for each Ethernet interface.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.1.1.2.1.1
slcNetEthIfSource The state/source for the IP Address and subnet mask for the Ethernet interface.	Enumeration Enumerated Values: 1 disabled 2 dhcp 3 bootp 4 static	.1.3.6.1.4.1.244.1.1.1.1.2.1.2
slcNetEthIfMode The speed and duplex for the Ethernet interface.	Enumeration Enumerated Values: 1 autoNegotiate 2 halfDuplex10mbit 3 fullDuplex10mbit 4 halfDuplex100mbit 5 fullDuplex100mbit 6 halfDuplex1000mbit 7 fullDuplex1000mbit	.1.3.6.1.4.1.244.1.1.1.1.2.1.3
slcNetEthIfIPv6Addr The IPv6 Address for each Ethernet interface.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.244.1.1.1.1.2.1.4
slcNetEthIfIPv6PrefixLength The length of the prefix for slcNetEthIfIPv6Addr (in bits).	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.244.1.1.1.1.2.1.5
slcNetEthIfMTU The Maximum Transmission Unit for the Ethernet interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.1.1.2.1.6
slcNetEthIfMacAddress The MAC Address for the Ethernet interface.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.244.1.1.1.1.2.1.7

Table of IP Filter Rulesets.  The number of entries is 
given by the value of slcNetFirewallRulesetNumber.

slcNetFirewallRulesetEntry row .1.3.6.1.4.1.244.1.1.1.2.10.1

An entry with all the attributes, including the rules, for
an IP Filter Ruleset.

Indexes

slcNetFirewallRulesetIndex

Column	Syntax	OID
slcNetFirewallRulesetIndex Reference index for each IP Filter Ruleset.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.244.1.1.1.2.10.1.1
slcNetFirewallRulesetName The name assigned to the IP Filter Ruleset.	OctetString	.1.3.6.1.4.1.244.1.1.1.2.10.1.2
slcNetFirewallRulesetNumRules The number of rules in the slcNetFirewallRulesetRules string.	Integer32 Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.1.2.10.1.3
slcNetFirewallRulesetRules The IP Filter rules that are defined for the Ruleset. The rule format is <IP>/<Mask Bits>;<Protocol>;<Ports>;<Action> and rules are separated by a colon. If the string is truncated because of system limitations, th…	OctetString	.1.3.6.1.4.1.244.1.1.1.2.10.1.4

Table of mappings between IP Filter Rulesets and interfaces.  
The number of entries is given by the value of 
slcNetFirewallMappingNumber.

slcNetFirewallMappingEntry row .1.3.6.1.4.1.244.1.1.1.2.12.1

An entry defining an interface that has an IP Filter Ruleset
assigned to it. The interface can be either an Ethernet
interface or a PC Card or Device Port modem.

Indexes

slcNetFirewallMappingIndex

Column	Syntax	OID
slcNetFirewallMappingIndex Reference index for each IP Filter mapping.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.244.1.1.1.2.12.1.1
slcNetFirewallMappingIfac The interface which has an IP Filter Ruleset assigned to it. If the interface is devicePort or usbPort, slcNetFirewallMappingIfacId defines which Device Port or USB Port (with an attached modem) the Ruleset is assig…	Enumeration Enumerated Values: 1 ethernet1 2 ethernet2 3 upperPCCard 4 lowerPCCard 5 devicePort 6 usbPort 7 internalModem	.1.3.6.1.4.1.244.1.1.1.2.12.1.2
slcNetFirewallMappingIfacId The identifier for a Device Port if slcNetFirewallMappingIfac equals devicePort(5), or the identifier for a USB Port if slcNetFirewallMappingIfac equals usbPort. Otherwise equals zero.	Integer32 Constraints: range: 0-48	.1.3.6.1.4.1.244.1.1.1.2.12.1.3
slcNetFirewallMappingRuleset The name of the IP Filter Ruleset assigned to the interface.	OctetString	.1.3.6.1.4.1.244.1.1.1.2.12.1.4

Table of static route entries.  The number of entries is 
given by the value of slcNetRouteStaticNumber.

slcNetRouteStaticEntry row .1.3.6.1.4.1.244.1.1.1.3.5.1

An entry with the IP Address, subnet mask, and gateway
for a static route.

Indexes

slcNetRouteStaticIndex

Column	Syntax	OID
slcNetRouteStaticIndex Reference index for each static route.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.244.1.1.1.3.5.1.1
slcNetRouteStaticIP The IP Address for the static route.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.1.3.5.1.2
slcNetRouteStaticMask The subnet mask for the static route.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.1.3.5.1.3
slcNetRouteStaticGateway The gateway for the static route.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.1.3.5.1.4

Table of NFS Mounts.

slcServNFSMountEntry row .1.3.6.1.4.1.244.1.1.2.8.1.1

An entry containing a NFS Mount and it's attributes.

Indexes

slcServNFSMountIndex

Column	Syntax	OID
slcServNFSMountIndex Reference index for each NFS Mount.	Integer32 Constraints: range: 1-3	.1.3.6.1.4.1.244.1.1.2.8.1.1.1
slcServNFSMountRemoteDir The remote directory of the NFS Mount, in the format <remote server>:/<remote directory>.	OctetString	.1.3.6.1.4.1.244.1.1.2.8.1.1.2
slcServNFSMountLocalDir The directory in the SLC on which the remote directory is mounted.	OctetString	.1.3.6.1.4.1.244.1.1.2.8.1.1.3
slcServNFSMountReadWrite If enabled, the remote NFS directory is mounted read-write. If disabled, the remote NFS directory is mounted read-only.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.8.1.1.4
slcServNFSMountMount If enabled, the remote NFS directory is configured to be mounted. If disabled, the remote NFS directory will not be mounted, or will be unmounted if is is mounted.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.8.1.1.5

Table of manually entered IP Address entries.  The number of 
entries is given by the value of slcServSLCNetNumber.

slcServSLCNetEntry row .1.3.6.1.4.1.244.1.1.2.10.3.1

An entry containing an IP Address for searching the SLC Network.

Indexes

slcServSLCNetIndex

Column	Syntax	OID
slcServSLCNetIndex Reference index for each manual IP Address.	Integer32 Constraints: range: 1-200	.1.3.6.1.4.1.244.1.1.2.10.3.1.1
slcServSLCNetIP The IP Address to search for in the SLC Network.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.10.3.1.2

Table of Host Lists.  The number of entries is given by the 
value of slcServHostListNumber.

slcServHostListEntry row .1.3.6.1.4.1.244.1.1.2.12.2.1

An entry containing a Host List, used for Dial-in connections
on a Device Port or PC Card modem.

Indexes

slcServHostListIndex

Column	Syntax	OID
slcServHostListIndex Reference index for each Host List.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.244.1.1.2.12.2.1.1
slcServHostListName The unique name assigned to the Host List.	OctetString	.1.3.6.1.4.1.244.1.1.2.12.2.1.2
slcServHostListRetryCount The number of times to retry connections to an individual host within the Host List.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.2.12.2.1.3
slcServHostListAuth If enabled, authentication is enabled for the hosts in the Host List.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.12.2.1.4
slcServHostListNumHosts The number of individual hosts in the Host List.	Integer32 Constraints: range: 0-10	.1.3.6.1.4.1.244.1.1.2.12.2.1.5
slcServHostListHosts A string containing all hosts in the Host List; the entry for each host is separated by a ';'. Each host entry is formatted as follows: '<Host>,<Protocol>,<TCP Port>,<Escape Sequence>;'.	OctetString	.1.3.6.1.4.1.244.1.1.2.12.2.1.6

Table of Sites.  The number of entries is given by the 
value of slcServSiteNumber.

slcServSiteEntry row .1.3.6.1.4.1.244.1.1.2.14.2.1

An entry containing a Site, used for connections on a
Device Port or PC Card/USB modem.

Indexes

slcServSiteIndex

Column	Syntax	OID
slcServSiteIndex Reference index for each Site.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.244.1.1.2.14.2.1.1
slcServSiteName The unique name assigned to the Site.	OctetString	.1.3.6.1.4.1.244.1.1.2.14.2.1.2
slcServSitePort The port the Site is assigned to. If the port is devicePort or usbPort, slcServSitePortId defines which Device Port or USB Port (with an attached modem) the port is assigned to.	Enumeration Enumerated Values: 1 none 2 devicePort 3 upperPCCard 4 lowerPCCard 5 usbPort 6 internalModem	.1.3.6.1.4.1.244.1.1.2.14.2.1.3
slcServSitePortId The identifier for a Device Port if slcServSitePort equals devicePort(1), or the identifier for a USB Port if slcServSitePort equals usbPort(5). Otherwise equals zero.	Integer32 Constraints: range: 0-48	.1.3.6.1.4.1.244.1.1.2.14.2.1.4
slcServSiteLoginHost For PPP or text authentication on dialin, the user login or CHAP host to use for authentication. If authentication is successful, the rest of the site parameters will be used for the connection.	OctetString	.1.3.6.1.4.1.244.1.1.2.14.2.1.5
slcServSiteCHAPSecret For PPP authentication on dialin, the CHAP secret to use for authentication.	OctetString	.1.3.6.1.4.1.244.1.1.2.14.2.1.6
slcServSiteTimeout The timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.	minutesInteger32 Constraints: range: 0-30	.1.3.6.1.4.1.244.1.1.2.14.2.1.7
slcServSiteLocalIP For PPP connections, the local IP Address - all zeros if it should be negotiated.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.14.2.1.8
slcServSiteRemoteIP For PPP connections, the remote IP Address - all zeros if it should be negotiated.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.14.2.1.9
slcServSiteStaticRouteIP For Dial-on-Demand PPP connections, the static route IP Address for the remote network.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.14.2.1.10
slcServSiteStaticRouteMask For Dial-on-Demand PPP connections, the static route subnet mask for the remote network.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.14.2.1.11
slcServSiteStaticRouteGateway For Dial-on-Demand PPP connections, the static route gateway for the remote network.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.2.14.2.1.12
slcServSiteDialoutNum The phone number to use for dial-out connections.	OctetString	.1.3.6.1.4.1.244.1.1.2.14.2.1.13
slcServSiteDialoutLogin For dial-out connections, the login to use for authenticating to the remote peer; or on dial-in, the login to use if the remote peer requests authentication (for example, a two way CHAP handshake).	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.2.14.2.1.14
slcServSiteDialback If enabled, the site has permission to use modem dialback.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.14.2.1.15
slcServSiteDialbackNum The phone number to use for dial-back connections.	OctetString	.1.3.6.1.4.1.244.1.1.2.14.2.1.16
slcServSiteDialbackDelay For Dial-back, specifies the delay between the dial-in and dial-out portion of the dialing sequence.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.2.14.2.1.17
slcServSiteIdleTimeout The timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0…	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.2.14.2.1.18
slcServSiteRestartDelay The delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.2.14.2.1.19
slcServSiteCBCPServerAllowNoCallback If enabled, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.14.2.1.20
slcServSiteNATState If enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.2.14.2.1.21
slcServSiteDialbackRetries For Dial-back, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.2.14.2.1.22

Table of Local Users entries.  The number of entries 
is given by the value of slcAuthLocalNumber.

slcAuthLocalUserEntry row .1.3.6.1.4.1.244.1.1.3.1.2.1

An entry containing a Local Users and it's attributes.

Indexes

slcAuthLocalUserIndex

Column	Syntax	OID
slcAuthLocalUserIndex Reference index for each Local User.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.244.1.1.3.1.2.1.1
slcAuthLocalUserLogin The login for the Local User. If the user account is locked (cannot login), the login is appended with a '*' character.	OctetString Constraints: range: 0-33	.1.3.6.1.4.1.244.1.1.3.1.2.1.2
slcAuthLocalUserUID The unique user identifier number for the Local User.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.244.1.1.3.1.2.1.3
slcAuthLocalUserListenPorts The Device Ports and PC Card slots/USB ports which the Local User has permission to access via 'connect listen'.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.4
slcAuthLocalUserDataPorts The Device Ports and PC Card slots/USB ports which the Local User has permission to access via 'connect direct'.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.5
slcAuthLocalUserClearPorts The Device Ports and PC Card slots/USB ports which the Local User has permission to clear.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.6
slcAuthLocalUserEscapeSeq The character sequence which the Local User uses to terminate connections to Device Ports.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.7
slcAuthLocalUserBreakSeq The character sequence which the Local User uses to send a break sequence.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.8
slcAuthLocalUserMenu The custom user menu defined for the Local User. If this is empty, there is no menu defined for the Local User. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically displ…	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.9
slcAuthLocalUserDialback If enabled, the Local User has permission to use modem dialback.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.1.2.1.10
slcAuthLocalUserDialbackNum The dialback number defined for the Local User.	OctetString	.1.3.6.1.4.1.244.1.1.3.1.2.1.11
slcAuthLocalUserGroup The group assigned to the Local User.	UserGroup Type Values: 1 default 2 power 3 administrators 4 custom	.1.3.6.1.4.1.244.1.1.3.1.2.1.12
slcAuthLocalUserRights The rights assigned to the Local User.	UserRights Type Constraints: range: 0..255	.1.3.6.1.4.1.244.1.1.3.1.2.1.13
slcAuthLocalUserPwdExpires If enabled, the local user's password will expire.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.1.2.1.14
slcAuthLocalUserChangePwd If enabled, the local user can change their password.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.1.2.1.15
slcAuthLocalUserChangePwdNextLogin If enabled, the local user must change their password at their next login.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.1.2.1.16

Table of RADIUS servers.

slcAuthRADIUSServerEntry row .1.3.6.1.4.1.244.1.1.3.4.4.1

An entry containing a RADIUS server and it's parameters.

Indexes

slcAuthRADIUSServerIndex

Column	Syntax	OID
slcAuthRADIUSServerIndex Reference index for each RADIUS server.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.3.4.4.1.1
slcAuthRADIUSServer The IPv4 Address of the RADIUS server.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.3.4.4.1.2
slcAuthRADIUSPort The RADIUS Server TCP Port Number.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.244.1.1.3.4.4.1.3
slcAuthRADIUSServerIPv6 The IPv6 Address of the RADIUS server.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.244.1.1.3.4.4.1.4

Table of Remote Users entries.  The number of entries 
is given by the value of slcAuthRemoteNumber.

slcAuthRemoteUserEntry row .1.3.6.1.4.1.244.1.1.3.7.2.1

An entry containing a Remote User and its attributes.

Indexes

slcAuthRemoteUserIndex

Column	Syntax	OID
slcAuthRemoteUserIndex Reference index for each Remote User.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.244.1.1.3.7.2.1.1
slcAuthRemoteUserLogin The login for the Remote User.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.244.1.1.3.7.2.1.2
slcAuthRemoteUserGroup The group assigned to the Remote User.	UserGroup Type Values: 1 default 2 power 3 administrators 4 custom	.1.3.6.1.4.1.244.1.1.3.7.2.1.3
slcAuthRemoteUserRights The rights assigned to the Remote User.	UserRights Type Constraints: range: 0..255	.1.3.6.1.4.1.244.1.1.3.7.2.1.4
slcAuthRemoteUserListenPorts The Device Ports and PC Card slots/USB ports which the Remote User has permission to access via 'connect listen'.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.5
slcAuthRemoteUserDataPorts The Device Ports and PC Card slots/USB ports which the Remote User has permission to access via 'connect direct'.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.6
slcAuthRemoteUserClearPorts The Device Ports and PC Card slots/USB ports which the Remote User has permission to clear.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.7
slcAuthRemoteUserEscapeSeq The character sequence which the Remote User uses to terminate connections to Device Ports.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.8
slcAuthRemoteUserBreakSeq The character sequence which the Remote User uses to send a break sequence.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.9
slcAuthRemoteUserMenu The custom user menu defined for the Remote User. If this is empty, there is no menu defined for the Remote User. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically dis…	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.10
slcAuthRemoteUserLocked If enabled, the Remote User's account is locked (blocked).	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.7.2.1.11
slcAuthRemoteUserDialback If enabled, the Remote User has permission to use modem dialback.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.7.2.1.12
slcAuthRemoteUserDialbackNum The dialback number defined for the Remote User.	OctetString	.1.3.6.1.4.1.244.1.1.3.7.2.1.13

Table of Groups entries.  The number of entries 
is given by the value of slcAuthGroupsNumber.

slcAuthGroupEntry row .1.3.6.1.4.1.244.1.1.3.8.2.1

An entry containing a Remote User and its attributes.

Indexes

slcAuthGroupIndex

Column	Syntax	OID
slcAuthGroupIndex Reference index for each Group.	Integer32 Constraints: range: 1-128	.1.3.6.1.4.1.244.1.1.3.8.2.1.1
slcAuthGroupName The name for the Group.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.244.1.1.3.8.2.1.2
slcAuthGroupRights The rights assigned to the Group.	UserRights Type Constraints: range: 0..255	.1.3.6.1.4.1.244.1.1.3.8.2.1.3
slcAuthGroupListenPorts The Device Ports and PC Card slots/USB ports which the Group has permission to access via 'connect listen'.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.4
slcAuthGroupDataPorts The Device Ports and PC Card slots/USB ports which the Group has permission to access via 'connect direct'.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.5
slcAuthGroupClearPorts The Device Ports and PC Card slots/USB ports which the Group has permission to clear.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.6
slcAuthGroupEscapeSeq The character sequence which the Group uses to terminate connections to Device Ports.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.7
slcAuthGroupBreakSeq The character sequence which the Group uses to send a break sequence.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.8
slcAuthGroupMenu The custom user menu defined for the Group. If this is empty, there is no menu defined for the Group. The menu name is followed by a slash '/' character and either a 'y' if the menu is automatically displayed at lo…	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.9
slcAuthGroupDialback If enabled, the Group has permission to use modem dialback.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.3.8.2.1.10
slcAuthGroupDialbackNum The dialback number defined for the Group.	OctetString	.1.3.6.1.4.1.244.1.1.3.8.2.1.11

Table for managing Device Port configuration.  The number of 
entries is given by the value of slcDevPortCfgNumber.

slcDevPortCfgEntry row .1.3.6.1.4.1.244.1.1.4.2.2.2.1

An entry containing all configuration settings for a Device Port.

Indexes

slcDevPortId

Column	Syntax	OID
slcDevPortId The identifier for a Device Port.	Integer32 Constraints: range: 1-48	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.1
slcDevPortCfgName The name of the Device Port.	OctetString Constraints: range: 1-30	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.2
slcDevPortCfgDevice The device that is connected to the Device Port. The 'slp*' and 'servertech' values are deprecated and have been replaced by the RPM functionality.	Enumeration Enumerated Values: 1 none 2 slp8 3 slp16 4 slp8Exp8 5 slp8Exp16 6 slp16Exp8 7 slp16Exp16 8 sensorsoft 9 servertech 10 rpm	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.3
slcDevPortCfgDevLogin The login used to authenticate to the device connected to the Device Port.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.4
slcDevPortCfgBreakSeq The character sequence for the Device Port to send a break.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.5
slcDevPortCfgTelnetState If enabled, Telnet connections to the Device Port are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.6
slcDevPortCfgTelnetPort TCP Port number for Telnet in connections.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.7
slcDevPortCfgTelnetAuth If enabled, the user is required to authenticate to access a Device Port with Telnet.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.8
slcDevPortCfgSSHState If enabled, SSH connections to the Device Port are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.9
slcDevPortCfgSSHPort TCP Port number for SSH in connections.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.10
slcDevPortCfgSSHAuth If enabled, the user is required to authenticate to access a Device Port with SSH.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.11
slcDevPortCfgTCPState If enabled, TCP connections to the Device Port are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.12
slcDevPortCfgTCPPort TCP Port number for TCP in connections.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.13
slcDevPortCfgTCPAuth If enabled, the user is required to authenticate to access a Device Port with TCP.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.14
slcDevPortCfgIP The IP Address for Telnet, SSH or TCP in to a Device Port.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.15
slcDevPortCfgBaud The baud rate of the Device Port.	Integer32 Constraints: range: 300-300 range: 600-600 range: 1200-1200 range: 2400-2400 range: 4800-4800 range: 9600-9600 range: 19200-19200 range: 38400-38400 range: 57600-57600 range: 115200-115200	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.16
slcDevPortCfgDataBits The data bits of the Device Port.	Integer32 Constraints: range: 7-8	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.17
slcDevPortCfgStopBits The stop bits of the Device Port.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.18
slcDevPortCfgParity The parity of the Device Port.	Enumeration Enumerated Values: 1 none 2 odd 3 even	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.19
slcDevPortCfgFlowControl The flow control of the Device Port.	Enumeration Enumerated Values: 1 none 2 xonxoff 3 rtscts	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.20
slcDevPortCfgLogins If enabled, authentication is required to access a serial device connected to a Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.21
slcDevPortCfgConnectDSR If enabled, the Device Port only establishes a connection if DSR (Data Set Ready) transitions to an asserted state.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.22
slcDevPortCfgDisconnectDSR If enabled, and a connection to a Device Port is currently in session, the connection will be terminated if DSR (Data Set Ready) transitions to a de-asserted state.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.23
slcDevPortCfgModemState For an external modem attached to the Device Port, indicates how the modem will be used.	Enumeration Enumerated Values: 1 disabled 2 dialout 3 dialin 4 dialback 5 dialondemand 6 dialinAndDialondemand 7 dialinHostList 8 cbcpServer 9 cbcpClient	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.24
slcDevPortCfgModemMode For an external modem attached to the Device Port, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).	Enumeration Enumerated Values: 1 ppp 2 text	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.25
slcDevPortCfgLocalIP For PPP connections, the local IP Address - all zeros if it should be negotiated.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.26
slcDevPortCfgRemoteIP For PPP connections, the remote IP Address - all zeros if it should be negotiated.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.27
slcDevPortCfgAuth For PPP connections, the type of authentication to be used.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.28
slcDevPortCfgCHAPHost For PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.29
slcDevPortCfgInitScript The initialization script for an external modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.30
slcDevPortCfgTimeout The timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.	minutesInteger32 Constraints: range: 0-30	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.31
slcDevPortCfgDialoutNum The phone number to use for dial-out connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.32
slcDevPortCfgDialoutLogin The login to use for dial-out connections.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.33
slcDevPortCfgDialbackMode For dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.	Enumeration Enumerated Values: 1 usernumber 2 fixed	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.34
slcDevPortCfgDialbackNum The phone number to use for dial-back connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.35
slcDevPortCfgNATState If enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.36
slcDevPortCfgLocalState If enabled, local logging is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.37
slcDevPortCfgNFSFileState If enabled, NFS File logging is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.38
slcDevPortCfgNFSDir The local directory of a NFS mount to use for logging.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.39
slcDevPortCfgNFSMaxFiles The maximum number of files to use for NFS file logging.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.40
slcDevPortCfgNFSMaxSize The maximum size of each file (in bytes) for NFS File logging.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.41
slcDevPortCfgEmailState If enabled, Token and Data Detection (previously called 'Email Logging') is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.42
slcDevPortCfgEmailTrigger The type of trigger to use for Token and Data Detection (previously called 'Email Logging') - number of data bytes received, or token/character string received.	Enumeration Enumerated Values: 1 bytecnt 2 textstring	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.43
slcDevPortCfgEmailByteThresh When Token and Data Detection (previously called 'Email Logging') is configured to trigger on a data byte count, the number of bytes required to trigger an action.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.44
slcDevPortCfgEmailDelay For Token and Data Detection (previously called 'Email Logging'), a time limit of how long the device port will capture data after the data trigger is detected and before closing the log file and performing the selec…	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.45
slcDevPortCfgEmailRestartDelay For Token and Data Detection (previously called 'Email Logging'), the period of time, after performing the selected actions, during which the device port will ignore additional characters received.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.46
slcDevPortCfgEmailTextString When Token and Data Detection (previously called 'Email Logging') is configured to trigger on a character string, this defines the character string that will trigger an action.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.47
slcDevPortCfgEmailTo For Token and Data Detection (previously called 'Email Logging'), if the Email action is enabled, this object defines the list of emails to send email notification to.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.48
slcDevPortCfgEmailSubject For Token and Data Detection (previously called 'Email Logging'), if the Email action is enabled, this object defines the subject to include with email notification.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.49
slcDevPortCfgPCCardState If enabled, PC Card logging is enabled for the Device Port. This value will be undefined if the SLC does not have PC Card slots.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.50
slcDevPortCfgPCCardLogTo For PC Card logging, which PC Card slot to use for logging. This value will be undefined if the SLC does not have PC Card slots.	Enumeration Enumerated Values: 1 upperSlot 2 lowerSlot	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.51
slcDevPortCfgPCCardMaxFiles The maximum number of files to use for PC Card logging. This value will be undefined if the SLC does not have PC Card slots.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.52
slcDevPortCfgPCCardMaxSize The maximum size of each file (in bytes) for PC Card logging. This value will be undefined if the SLC does not have PC Card slots.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.53
slcDevPortCfgAction Performs an action on a Device Port. A read of this object always returns the value noAction(1). Setting this object to zeroPortCounters(2) will reset all port counters given in slcDevPortStateTable. Setting this …	Enumerationr/w Enumerated Values: 1 noAction 2 zeroPortCounters 3 clearLocalLog 4 terminateConnections	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.54
slcDevPortCfgEmailSend When a trigger is received, the type of notification to send: email, SNMP trap, or email and SNMP trap. This object is deprecated; instead refer to slcDevPortCfgTokenAction.	Enumeration Enumerated Values: 1 email 2 snmptrap 3 both	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.55
slcDevPortCfgBanner The banner displayed when the Device Port is connected to via SSH or Telnet.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.56
slcDevPortCfgIdleTimeout The timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0…	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.57
slcDevPortCfgRestartDelay The delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.58
slcDevPortCfgCallerIdLogging If enabled, caller id logging is enabled for a modem dial-in connection.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.59
slcDevPortCfgCallerIdATCmd The modem AT command required to initiate caller id logging by the modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.60
slcDevPortCfgDODAuth For PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.61
slcDevPortCfgDODCHAPHost For PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.62
slcDevPortCfgSLMLoggingState If enabled, SLM logging is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.63
slcDevPortCfgSLMNMS The IP Addresses of up to three SNMP Network Management Stations defined used for SLM Logging. Multiple IP Addresses will be separated by a comma.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.64
slcDevPortCfgSLMByteThresh The number of bytes required to trigger SLM logging.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.65
slcDevPortCfgSLMTimeFrame The time frame for SLM logging, in seconds.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.66
slcDevPortCfgWebColumns The number of columns in the Web SSH or Telnet window for this Device Port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.67
slcDevPortCfgWebRows The number of rows in the Web SSH or Telnet window for this Device Port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.68
slcDevPortCfgSyslogState If enabled, Syslog logging is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.69
slcDevPortCfgHostList When slcDevPortCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.70
slcDevPortCfgDevLowTemp The low temperature limit, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.	CelsiusSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.71
slcDevPortCfgDevHighTemp The high temperature limit, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.	CelsiusSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.72
slcDevPortCfgDevTemperature The actual temperature, in Celsius, for the device connected to this Device Port. If the temperature is not applicable, an empty string will be returned.	CelsiusOctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.73
slcDevPortCfgDevLowHumidity The low humidty limit, in percentage, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.74
slcDevPortCfgDevHighHumidity The high humidty limit, in percentage, for the device connected to this Device Port. If the temperature is not applicable, 9999 will be returned.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.75
slcDevPortCfgDevHumidity The actual humidity, in percentage, for the device connected to this Device Port. If the temperature is not applicable, an empty string will be returned.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.76
slcDevPortCfgDevTraps If enabled, traps will be sent when one of the limits for the device connected to this Device Port are exceeded.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.77
slcDevPortCfgShowLines If enabled, upon connecting to the Device Port, a series of characters (or lines) output to the Device Port before it was connected to are displayed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.78
slcDevPortCfgNumberShowLines If slcDevPortCfgShowLines is enabled, the number of lines that are displayed upon connecting to the Device Port.	Integer32 Constraints: range: 1-50	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.79
slcDevPortCfgViewPortLog If enabled, upon using 'connect direct' to a Device Port, the slcDevPortCfgPortLogSeq key sequence can be typed to view the end of the port log for the current Device Port, or a different Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.80
slcDevPortCfgPortLogSeq The character sequence to view the port log for the Device Port.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.81
slcDevPortCfgMaxDirectConnects The maximum number of direct connects at the CLI for the Device Port.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.82
slcDevPortCfgTelnetTimeout The timeout (in seconds) for Telnet connections. A value of 0 indicates that timeouts are disabled.	secondsInteger32 Constraints: range: 0-1800	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.83
slcDevPortCfgSSHTimeout The timeout (in seconds) for SSH connections. A value of 0 indicates that timeouts are disabled.	secondsInteger32 Constraints: range: 0-1800	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.84
slcDevPortCfgTCPTimeout The timeout (in seconds) for TCP connections. A value of 0 indicates that timeouts are disabled.	secondsInteger32 Constraints: range: 0-1800	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.85
slcDevPortCfgCBCPClientType When slcDevPortCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.	Enumeration Enumerated Values: 1 adminDefined 2 userDefined	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.86
slcDevPortCfgCBCPServerAllowNoCallback If enabled and slcDevPortCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.87
slcDevPortCfgDialbackDelay When slcDevPortCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.88
slcDevPortCfgUSBState If enabled, USB logging is enabled for the Device Port. This value will be undefined if the SLC does not have USB Ports.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.89
slcDevPortCfgUSBLogTo For USB logging, which USB port to use for logging. This value will be undefined if the SLC does not have USB Ports.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.90
slcDevPortCfgUSBMaxFiles The maximum number of files to use for USB logging. This value will be undefined if the SLC does not have USB Ports.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.91
slcDevPortCfgUSBMaxSize The maximum size of each file (in bytes) for USB logging. This value will be undefined if the SLC does not have USB Ports.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.92
slcDevPortCfgCHAPAuthLocalUsers If enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.93
slcDevPortCfgUseSites If enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of …	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.94
slcDevPortCfgDialbackRetries When slcDevPortCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.95
slcDevPortCfgGroup The group or groups that may access the Device Port.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.96
slcDevPortCfgIPMask The network mask associated with slcDevPortCfgIPMask.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.97
slcDevPortCfgDevPrompt If the device port is connected to a SLP or ServerTech CDU, specifies the prompt that is configured for the SLP or ServerTech CDU. This object is deprecated, and has been replaced by the RPM functionality.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.98
slcDevPortCfgDevNumOutlets If the device port is connected to a ServerTech CDU, specifies the number of outlets on the primary/master ServerTech unit. This object is deprecated, and has been replaced by the RPM functionality.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.99
slcDevPortCfgDevNumExpOutlets If the device port is connected to a ServerTech CDU, specifies the number of outlets on the expansion ServerTech unit. This object is deprecated, and has been replaced by the RPM functionality.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.100
slcDevPortCfgReversePinout If enabled, swaps the positions of the serial lines, such that the direction of data or the signal is reversed. For instance, TX is swapped with RX. Enabling Reverse Pinout facilitates connections to Cisco and Sun …	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.101
slcDevPortCfgUSBVBUS For SLC8000 USB Device Ports only. If enabled, the USB VBUS signal provides power to the USB device attached to a device port. Disabling VBUS will power down the device as long as it is bus-powered instead of self-po…	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.102
slcDevPortCfgAssertDTR For RJ45 Device Ports only. By default, DTR is asserted on a device port nearly all of the time (except momentarily when a port is opened for operations). Unchecking this option will deassert DTR, simulating a cable…	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.103
slcDevPortCfgPortType Indicates the connector type on the device port: RJ45 or USB.	Enumeration Enumerated Values: 1 rj45 2 usb	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.104
slcDevPortCfgTelnetTimeoutDataDirection If slcDevPortCfgTelnetTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.	TimeoutDataDirection Type Values: 1 incomingNetwork 2 outgoingNetwork 3 bothDirections	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.105
slcDevPortCfgSSHTimeoutDataDirection If slcDevPortCfgSSHTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.	TimeoutDataDirection Type Values: 1 incomingNetwork 2 outgoingNetwork 3 bothDirections	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.106
slcDevPortCfgTCPTimeoutDataDirection If slcDevPortCfgTCPTimeout is enabled, this setting indicates the direction of data used to determine if the connection has timed out.	TimeoutDataDirection Type Values: 1 incomingNetwork 2 outgoingNetwork 3 bothDirections	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.107
slcDevPortCfgIdleTimeoutMessage If enabled, a message will be displayed to a user when their connection to a device port will be terminated soon due to the connection being idle.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.108
slcDevPortCfgNumberOfSessionsMessage If enabled, a message will be displayed to a user when connecting to a device port that indicates how many users are currently connected to the device port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.109
slcDevPortCfgMinimizeLatency If enabled, device port latency will be minimized by reducing read delays.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.110
slcDevPortCfgTelnetSoftIAC If enabled, the Telnet server will not block waiting for the initial Telnet protocol IAC option responses.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.111
slcDevPortCfgSendTermString If enabled, and a slcDevPortCfgTerminationString is defined, when a network connection to a device port is terminated, the termination string is sent to the device connected to the device port. The string should be …	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.112
slcDevPortCfgTerminationString The termination string sent to the device connected to the device port if slcDevPortCfgSendTermString is enabled.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.113
slcDevPortCfgPowerManagementSeq The key sequence that displays the Power Management menu when a user is connected to a device port.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.114
slcDevPortCfgPowerSupplies A string that describes the managed power supplies configured for the device port. A device port can have up to four power supplies that provide power for the device connected to the device port. The string is a com…	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.115
slcDevPortCfgToggleDTR Applies to RJ45 device ports only. If enabled, when a user disconnects from a device port, DTR will be toggled. This feature can be used when a serial connection requires DSR to be active for the attached device t…	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.116
slcDevPortCfgTokenAction For Token and Data Detection, a string containing one or more actions that will be performed if a data trigger occurs: syslog, email, trap, sendstring, powersupply.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.117
slcDevPortCfgTokenSendString For Token and Data Detection (previously called 'Email Logging'), if the Send String action is enabled, this object defines the string to send to the device connected to the device port.	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.118
slcDevPortCfgTokenPowerSupply For Token and Data Detection (previously called 'Email Logging'), if the Control Power Supply action is enabled, this object defines the name of the managed power supply to perform an action on. This string can be 'a…	OctetString	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.119
slcDevPortCfgTokenPowerAction For Token and Data Detection (previously called 'Email Logging'), if the Control Power Supply action is enabled, this object defines the action to take on slcDevPortCfgTokenPowerSupply.	Enumeration Enumerated Values: 1 turnOff 2 turnOn 3 cyclePower	.1.3.6.1.4.1.244.1.1.4.2.2.2.1.120

Table of Device Port state entries.  The number of 
entries is given by the value of slcDevPortStateNumber.

slcDevPortStateEntry row .1.3.6.1.4.1.244.1.1.4.2.3.2.1

An entry containing all state information for a Device Port.

Indexes

slcDevPortStateIndex

Column	Syntax	OID
slcDevPortStateIndex Reference index for each Device Port State entry.	Integer32 Constraints: range: 1-48	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.1
slcDevPortStateBytesInput The number of bytes input to the Device Port since boot or the last time Device Port statistics were zeroed.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.2
slcDevPortStateBytesOutput The number of bytes output from the Device Port since boot or the last time Device Port statistics were zeroed.	bytesSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.3
slcDevPortStateFramingErrors The number of framing errors for the Device Port since boot or the last time Device Port statistics were zeroed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.4
slcDevPortStateParityErrors The number of parity errors for the Device Port since boot or the last time Device Port statistics were zeroed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.5
slcDevPortStateOverrunErrors The number of overrun errors for the Device Port since boot or the last time Device Port statistics were zeroed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.6
slcDevPortStateFlowControlViolations The number of flow control violations for the Device Port since boot or the last time Device Port statistics were zeroed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.7
slcDevPortStateDSR If enabled, Data Set Ready is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.8
slcDevPortStateDTR If enabled, Data Terminal Ready is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.9
slcDevPortStateCTS If enabled, Clear To Send is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.10
slcDevPortStateRTS If enabled, Request To Send is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.11
slcDevPortStateCD If enabled, Carrier Detect is enabled for the Device Port.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.2.3.2.1.12

Table of PC Card configuration entries.  There are two entries 
in the table, index (1) for the upper PC Card slot, and index 
(2) for the lower PC Card slot.  This table will be empty if 
the SLC does not have PC Card slots.

slcPCCardCfgEntry row .1.3.6.1.4.1.244.1.1.4.3.1.1

An entry containing all configuration settings for a PC Card Slot.

Indexes

slcPCCardCfgIndex

Column	Syntax	OID
slcPCCardCfgIndex Reference index for each PC Card Configuration entry.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.4.3.1.1.1
slcPCCardCfgCardType The type of PC Card in the slot.	Enumeration Enumerated Values: 1 none 2 storage 3 modem 4 isdn 5 wireless 6 gsmmodem	.1.3.6.1.4.1.244.1.1.4.3.1.1.2
slcPCCardCfgCardId The identifying string of the card in the slot.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.3
slcPCCardCfgBaud For ISDN and modem cards, the baud rate.	Integer32 Constraints: range: 300-300 range: 600-600 range: 1200-1200 range: 2400-2400 range: 4800-4800 range: 9600-9600 range: 19200-19200 range: 38400-38400 range: 57600-57600 range: 115200-115200	.1.3.6.1.4.1.244.1.1.4.3.1.1.4
slcPCCardCfgDataBits For ISDN and modem cards, the data bits.	Integer32 Constraints: range: 7-8	.1.3.6.1.4.1.244.1.1.4.3.1.1.5
slcPCCardCfgStopBits For ISDN and modem cards, the stop bits.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.4.3.1.1.6
slcPCCardCfgParity For ISDN and modem cards, the parity.	Enumeration Enumerated Values: 1 none 2 odd 3 even	.1.3.6.1.4.1.244.1.1.4.3.1.1.7
slcPCCardCfgFlowControl For ISDN and modem cards, the flow control.	Enumeration Enumerated Values: 1 none 2 xonxoff 3 rtscts	.1.3.6.1.4.1.244.1.1.4.3.1.1.8
slcPCCardCfgModemState For ISDN and modem cards, indicates how the modem will be used.	Enumeration Enumerated Values: 1 disabled 2 dialout 3 dialin 4 dialback 5 dialondemand 6 dialinAndDialondemand 7 dialinHostList 8 cbcpServer 9 cbcpClient	.1.3.6.1.4.1.244.1.1.4.3.1.1.9
slcPCCardCfgModemMode For ISDN and modem cards, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).	Enumeration Enumerated Values: 1 ppp 2 text	.1.3.6.1.4.1.244.1.1.4.3.1.1.10
slcPCCardCfgLocalIP For PPP connections, the local IP Address (all zeros if it should be negotiated).	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.3.1.1.11
slcPCCardCfgRemoteIP For PPP connections, the remote IP Address (all zeros if it should be negotiated).	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.3.1.1.12
slcPCCardCfgAuth For PPP connections, the type of authentication to be used.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.3.1.1.13
slcPCCardCfgCHAPHost For PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.14
slcPCCardCfgInitScript The initialization script for an external modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.15
slcPCCardCfgTimeout The timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.	minutesInteger32 Constraints: range: 0-30	.1.3.6.1.4.1.244.1.1.4.3.1.1.16
slcPCCardCfgDialoutNum The phone number to use for dial-out connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.17
slcPCCardCfgDialoutLogin The login to use for dial-out connections.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.4.3.1.1.18
slcPCCardCfgDialbackMode For dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.	Enumeration Enumerated Values: 1 usernumber 2 fixed	.1.3.6.1.4.1.244.1.1.4.3.1.1.19
slcPCCardCfgDialbackNum The phone number to use for dial-back connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.20
slcPCCardCfgNATState If enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.21
slcPCCardCfgStorageFS For storage cards, the type of filesystem on the card.	Enumeration Enumerated Values: 1 notmounted 2 ext2 3 fat	.1.3.6.1.4.1.244.1.1.4.3.1.1.22
slcPCCardCfgISDNChannel The channel on the ISDN card to use, either 1 or 2.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.3.1.1.23
slcPCCardCfgISDNChannelNum The phone number associated with the selected ISDN channel.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.24
slcPCCardCfgTelnetState If enabled, Telnet connections to the modem/ISDN PC Card are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.25
slcPCCardCfgTelnetPort TCP Port number for Telnet connections directly to the modem/ISDN PC Card.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.3.1.1.26
slcPCCardCfgTelnetAuth If enabled, the user is required to authenticate to access the modem/ISDN PC Card with Telnet.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.27
slcPCCardCfgSSHState If enabled, SSH connections to the modem/ISDN PC Card are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.28
slcPCCardCfgSSHPort TCP Port number for SSH connections directly to the modem/ISDN PC Card.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.3.1.1.29
slcPCCardCfgSSHAuth If enabled, the user is required to authenticate to access the modem/ISDN PC Card with SSH.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.30
slcPCCardCfgTCPState If enabled, TCP connections to the modem/ISDN PC Card are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.31
slcPCCardCfgTCPPort TCP Port number for TCP connections directly to the modem/ISDN PC Card.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.3.1.1.32
slcPCCardCfgTCPAuth If enabled, the user is required to authenticate to access the modem/ISDN PC Card with TCP.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.33
slcPCCardCfgGSMPIN The PIN associated with the GSM/GPRS PC Card modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.34
slcPCCardCfgGSMNetworkNameobsolete The Network Name associated with the GSM/GPRS PC Card modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.35
slcPCCardCfgGSMPPPCompression If enabled, PPP compression is enabled for GSM/GPRS PC Card modem connections.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.36
slcPCCardCfgGSMAutoAcquireDNS If enabled, DNS servers will be acquired vi GSM/GPRS PC Card modem PPP connections.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.37
slcPCCardCfgGSMDialoutMode The mode to be used for GSM/GPRS PC Card modems configured for dialout.	Enumeration Enumerated Values: 1 gprs 2 gsm	.1.3.6.1.4.1.244.1.1.4.3.1.1.38
slcPCCardCfgGSMContextID The Context Id string used for GSM/GPRS PC Card modems configured for GPRS dialout mode.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.39
slcPCCardCfgGSMBearerService The Bearer Service Type string used for GSM/GPRS PC Card modems configured for GSM dialin/dialout mode.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.40
slcPCCardCfgIdleTimeout The timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.3.1.1.41
slcPCCardCfgRestartDelay The delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.3.1.1.42
slcPCCardCfgCallerIdLogging If enabled, caller id logging is enabled for a modem dial-in connection.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.43
slcPCCardCfgCallerIdATCmd The modem AT command required to initiate caller id logging by the modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.44
slcPCCardCfgDODAuth For PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.3.1.1.45
slcPCCardCfgDODCHAPHost For PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.46
slcPCCardCfgHostList When slcPCCardCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.47
slcPCCardCfgCBCPClientType When slcPCCardCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.	Enumeration Enumerated Values: 1 adminDefined 2 userDefined	.1.3.6.1.4.1.244.1.1.4.3.1.1.48
slcPCCardCfgCBCPServerAllowNoCallback If enabled and slcPCCardCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.49
slcPCCardCfgDialbackDelay When slcPCCardCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.3.1.1.50
slcPCCardCfgCHAPAuthLocalUsers If enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.51
slcPCCardCfgUseSites If enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of …	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.3.1.1.52
slcPCCardCfgDialbackRetries When slcPCCardCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.3.1.1.53
slcPCCardCfgGroup The group or groups that may access the PC Card slot.	OctetString	.1.3.6.1.4.1.244.1.1.4.3.1.1.54

Table of USB configuration entries.  There is one entry in the 
table, index (1) for USB port 1.  This table will be empty if 
the SLC does not have USB Ports.

slcDevUSBCfgEntry row .1.3.6.1.4.1.244.1.1.4.5.2.1

An entry containing all configuration settings for a USB port.

Indexes

slcDevUSBId

Column	Syntax	OID
slcDevUSBId The identifier for a USB Port (1 indicates USB Port U1).	Integer32 Constraints: range: 1-1	.1.3.6.1.4.1.244.1.1.4.5.2.1.1
slcDevUSBCfgCardType The type of USB device in the port.	Enumeration Enumerated Values: 1 none 2 storage 3 modem 4 isdn 5 wireless 6 gsmmodem	.1.3.6.1.4.1.244.1.1.4.5.2.1.2
slcDevUSBCfgCardId The identifying string of the device in the port.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.3
slcDevUSBCfgStorageFS For thumb drives, the type of filesystem on the card.	Enumeration Enumerated Values: 1 notmounted 2 ext2 3 fat	.1.3.6.1.4.1.244.1.1.4.5.2.1.4
slcDevUSBCfgBaud For modem cards, the baud rate.	Integer32 Constraints: range: 300-300 range: 600-600 range: 1200-1200 range: 2400-2400 range: 4800-4800 range: 9600-9600 range: 19200-19200 range: 38400-38400 range: 57600-57600 range: 115200-115200	.1.3.6.1.4.1.244.1.1.4.5.2.1.5
slcDevUSBCfgDataBits For modem cards, the data bits.	Integer32 Constraints: range: 7-8	.1.3.6.1.4.1.244.1.1.4.5.2.1.6
slcDevUSBCfgStopBits For modem cards, the stop bits.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.244.1.1.4.5.2.1.7
slcDevUSBCfgParity For modem cards, the parity.	Enumeration Enumerated Values: 1 none 2 odd 3 even	.1.3.6.1.4.1.244.1.1.4.5.2.1.8
slcDevUSBCfgFlowControl For modem cards, the flow control.	Enumeration Enumerated Values: 1 none 2 xonxoff 3 rtscts	.1.3.6.1.4.1.244.1.1.4.5.2.1.9
slcDevUSBCfgModemState For modem cards, indicates how the modem will be used.	Enumeration Enumerated Values: 1 disabled 2 dialout 3 dialin 4 dialback 5 dialondemand 6 dialinAndDialondemand 7 dialinHostList 8 cbcpServer 9 cbcpClient	.1.3.6.1.4.1.244.1.1.4.5.2.1.10
slcDevUSBCfgModemMode For modem cards, the mode: PPP (for Dial-in and Dial-out) and text (for Dial-in and Dial-back).	Enumeration Enumerated Values: 1 ppp 2 text	.1.3.6.1.4.1.244.1.1.4.5.2.1.11
slcDevUSBCfgLocalIP For PPP connections, the local IP Address (all zeros if it should be negotiated).	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.5.2.1.12
slcDevUSBCfgRemoteIP For PPP connections, the remote IP Address (all zeros if it should be negotiated).	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.244.1.1.4.5.2.1.13
slcDevUSBCfgAuth For PPP connections, the type of authentication to be used.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.5.2.1.14
slcDevUSBCfgCHAPHost For PPP connections with CHAP authentication, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.15
slcDevUSBCfgDODAuth For PPP connections that are configured for both Dial-in and Dial-on-Demand, the type of authentication to be used for Dial-on-Demand.	Enumeration Enumerated Values: 1 pap 2 chap	.1.3.6.1.4.1.244.1.1.4.5.2.1.16
slcDevUSBCfgDODCHAPHost For PPP connections that are configured for both Dial-in and Dial-on-Demand, with CHAP authentication for Dial-on-Demand, the host (for Unix) or user (for Windows) to use.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.17
slcDevUSBCfgInitScript The initialization script for a modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.18
slcDevUSBCfgTimeout The timeout (in minutes) for text connections. A value of 0 indicates that timeouts are disabled.	minutesInteger32 Constraints: range: 0-30	.1.3.6.1.4.1.244.1.1.4.5.2.1.19
slcDevUSBCfgDialoutNum The phone number to use for dial-out connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.20
slcDevUSBCfgDialoutLogin The login to use for dial-out connections.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.244.1.1.4.5.2.1.21
slcDevUSBCfgDialbackMode For dial-back connections, defines the phone number to call: a number associated with the authenticated user, or a fixed number associated with the Device Port.	Enumeration Enumerated Values: 1 usernumber 2 fixed	.1.3.6.1.4.1.244.1.1.4.5.2.1.22
slcDevUSBCfgDialbackNum The phone number to use for dial-back connections.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.23
slcDevUSBCfgDialbackDelay When slcDevUSBCfgModemState is set to dialback or cbcpServer, specifies the delay between the dial-in and dial-out portion of the dialing sequence.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.5.2.1.24
slcDevUSBCfgNATState If enabled, use NAT (Network Address Translation) to allow dial-in and dial-back users to access the network connected to Eth1 and Eth2.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.25
slcDevUSBCfgIdleTimeout The timeout (in seconds) for dial-in and dial-on-demand PPP connections. If no traffic is received for the PPP connection in the time defined by the idle timeout, the PPP connection will be terminated. A value of 0…	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.5.2.1.26
slcDevUSBCfgRestartDelay The delay (in seconds) to wait before restarting dial-out or dial-on-demand PPP connections.	secondsSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.5.2.1.27
slcDevUSBCfgCallerIdLogging If enabled, caller id logging is enabled for a modem dial-in connection.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.28
slcDevUSBCfgCallerIdATCmd The modem AT command required to initiate caller id logging by the modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.29
slcDevUSBCfgHostList When slcDevUSBCfgModemState is set to dialinHostList, the name of the Host List used for Dial-in.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.30
slcDevUSBCfgCBCPClientType When slcDevUSBCfgModemState is set to cbcpClient, the preferred type of dialback number to use for CBCP negotiation.	Enumeration Enumerated Values: 1 adminDefined 2 userDefined	.1.3.6.1.4.1.244.1.1.4.5.2.1.31
slcDevUSBCfgCBCPServerAllowNoCallback If enabled and slcDevUSBCfgModemState is set to cbcpServer, the SLC will allow the PPP peer to select the No Callback option during CBCP negotiation.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.32
slcDevUSBCfgTelnetState If enabled, Telnet connections to the USB modem are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.33
slcDevUSBCfgTelnetPort TCP Port number for Telnet connections directly to the USB modem.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.5.2.1.34
slcDevUSBCfgTelnetAuth If enabled, the user is required to authenticate to access the USB modem with Telnet.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.35
slcDevUSBCfgSSHState If enabled, SSH connections to the USB modem are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.36
slcDevUSBCfgSSHPort TCP Port number for SSH connections directly to the USB modem.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.5.2.1.37
slcDevUSBCfgSSHAuth If enabled, the user is required to authenticate to access the USB modem with SSH.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.38
slcDevUSBCfgTCPState If enabled, TCP connections to the USB modem are allowed.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.39
slcDevUSBCfgTCPPort TCP Port number for TCP connections directly to the USB modem.	Integer32 Constraints: range: 1025-65535	.1.3.6.1.4.1.244.1.1.4.5.2.1.40
slcDevUSBCfgTCPAuth If enabled, the user is required to authenticate to access the USB modem with TCP.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.41
slcDevUSBCfgGSMPIN The PIN associated with the GSM/GPRS modem.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.42
slcDevUSBCfgGSMPPPCompression If enabled, PPP compression is enabled GSM/GPRS modem connections.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.43
slcDevUSBCfgGSMAutoAcquireDNS If enabled, DNS servers will be acquired vi GSM/GPRS modem PPP connections.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.44
slcDevUSBCfgGSMDialoutMode The mode to be used for GSM/GPRS modems configured for dialout.	Enumeration Enumerated Values: 1 gprs 2 gsm	.1.3.6.1.4.1.244.1.1.4.5.2.1.45
slcDevUSBCfgGSMContextID The Context Id string used for GSM/GPRS modems configured for GPRS dialout mode.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.46
slcDevUSBCfgGSMBearerService The Bearer Service Type string used for GSM/GPRS modems configured for GSM dialin/dialout mode.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.47
slcDevUSBCfgCHAPAuthLocalUsers If enabled, the local user list (login and password) is used to validate the CHAP host and secret sent by a remote PPP peer for CHAP authentication, instead of using the CHAP host and secret associated with a modem.	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.48
slcDevUSBCfgUseSites If enabled, sites (a set of site-oriented modem parameters that can be activated by various modem-related events such as authentication, outbound traffic for Dial-on-demand connections, etc.) will be used instead of …	EnabledState Type Values: 1 disabled 2 enabled	.1.3.6.1.4.1.244.1.1.4.5.2.1.49
slcDevUSBCfgDialbackRetries When slcDevUSBCfgModemState is set to dialback or cbcpServer, specifies the number of times the SLC will retry the dial-out portion of the dialing sequence if the first attempt to dial-out fails.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.244.1.1.4.5.2.1.50
slcDevUSBCfgDialtoneCheck The time (in minutes) between checks for a modem dialtone. A value of 0 indicates that dialtone checks are disabled.	minutesInteger32 Constraints: range: 0-600	.1.3.6.1.4.1.244.1.1.4.5.2.1.51
slcDevUSBCfgGroup The group or groups that may access the USB port.	OctetString	.1.3.6.1.4.1.244.1.1.4.5.2.1.52