Juniper-UNI-SONET-MIB Table View

This table contains entries for SONET interfaces present in the
system.

juniSonetMediumEntry row .1.3.6.1.4.1.4874.2.2.7.1.1.1

Each entry describes the characteristics of an SONET interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
juniSonetMediumTypedeprecated This variable identifies whether a SONET or a SDH signal is used across this interface. This object was deprecated because the same information is provided by the SONET-MIB.sonetMediumType object (RFC 2558).	Enumerationr/w Enumerated Values: 1 sonet 2 sdh	.1.3.6.1.4.1.4874.2.2.7.1.1.1.1
juniSonetMediumLoopbackConfig The current loopback state of the SONET/SDH interface. The values mean: sonetNoLoop Not in the loopback state. A device that is not capable of performing a loopback on this …	Enumerationr/w Enumerated Values: 0 sonetNoLoop 1 sonetFacilityLoop 2 sonetTerminalLoop 3 sonetOtherLoop	.1.3.6.1.4.1.4874.2.2.7.1.1.1.2
juniSonetMediumTimingSource Selects the source from which transmit timing is derived. loop timing is recovered from the receiver internalModule timing is from the module associated with this interface internalChassis ti…	Enumerationr/w Enumerated Values: 0 loop 1 internalModule 2 internalChassis	.1.3.6.1.4.1.4874.2.2.7.1.1.1.3
juniSonetMediumCircuitIdentifierdeprecated This variable contains the transmission vendor's circuit identifier, for the purpose of facilitating troubleshooting. This object was deprecated because the same information is provided by the SONET-MIB.sonetMediumCirc…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.4874.2.2.7.1.1.1.4
juniSonetMediumTriggerAlarms The alarms that are used in the operational status calculation for this SONET interface. sectionLOS When this bit is set, section LOS is used for operational status calculation. sectionLOF When…	Bits Enumerated Values: 0 sectionLOS 1 sectionLOF 2 lineAIS 3 lineRDI	.1.3.6.1.4.1.4874.2.2.7.1.1.1.5
juniSonetMediumTriggerDelay The time delay (in milliseconds) before a defect is accepted as an alarm for this SONET interface.	msInteger32r/w Constraints: range: 0-2500	.1.3.6.1.4.1.4874.2.2.7.1.1.1.6

This table contains entries for SONET Paths present in the system.

juniSonetPathCapabilityEntry row .1.3.6.1.4.1.4874.2.2.7.2.1.1

Each entry describes the SONET path capability of a SONET interface.
This table is index by the ifIndex of the SONET interface.

Indexes

IF-MIBifIndex

Column	Syntax	OID
juniSonetPathRemoveFlag This variable identifies whether a SONET/SDH supports the deletion of SONET Paths. A value of true(1) indicates the SONET path is removable; a value of false(2) indicates the SONET path cannot be removed.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4874.2.2.7.2.1.1.1
juniSonetPathChannelized Identifies whether or not this SONET interface supports channelization. A value of true(1) indicates the SONET path is channelized; a value of false(2) indicates the SONET path is not channelized.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4874.2.2.7.2.1.1.2
juniSonetPathMaximumChannels Identifies the maximum number of SONET paths/channels for this interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.7.2.1.1.3
juniSonetPathMinimumPathSpeed Identifies the minimum SONET path speed for this interface.	JuniSonetLineSpeed Type Values: 0 sonetUnknownSpeed 1 sonetOc1Stm0 2 sonetOc3Stm1 3 sonetOc12Stm3 4 sonetOc48Stm16	.1.3.6.1.4.1.4874.2.2.7.2.1.1.4
juniSonetPathMaximumPathSpeed Identifies the maximum SONET path speed for this interface.	JuniSonetLineSpeed Type Values: 0 sonetUnknownSpeed 1 sonetOc1Stm0 2 sonetOc3Stm1 3 sonetOc12Stm3 4 sonetOc48Stm16	.1.3.6.1.4.1.4874.2.2.7.2.1.1.5

This table contains entries for SONET Path interfaces present in the
system.

juniSonetPathEntry row .1.3.6.1.4.1.4874.2.2.7.2.3.1

Each entry describes the characteristics of an SONET Path interface.

Indexes

juniSonetPathIfIndex

Column	Syntax	OID
juniSonetPathIfIndex The ifIndex of the SONET Path interface. When creating entries in this table, suitable values for this object are determined by reading juniSonetPathNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.7.2.3.1.1
juniSonetPathLogicalChannel The logical channel number assigned to this SONET Path. If the underlying SONET interface does not support channelization, the value of this object is zero.	JuniSonetLogicalPathChannelr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.4874.2.2.7.2.3.1.2
juniSonetPathSpeed The line speed associated with this SONET PATH.	JuniSonetLineSpeedr/w Type Values: 0 sonetUnknownSpeed 1 sonetOc1Stm0 2 sonetOc3Stm1 3 sonetOc12Stm3 4 sonetOc48Stm16	.1.3.6.1.4.1.4874.2.2.7.2.3.1.3
juniSonetPathHierarchy The SONET Path hierarchy associated with this path.	JuniSonetPathHierarchyr/w Type Constraints: range: 0..32	.1.3.6.1.4.1.4874.2.2.7.2.3.1.4
juniSonetPathLowerIfIndex The ifIndex of the interface over which this SONET Path interface is to be layered - typically a SONET/SDH interface. A value of zero indicates no layering. An implementation may choose to require that a nonzero value…	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.7.2.3.1.5
juniSonetPathRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.7.2.3.1.6
juniSonetPathTriggerAlarms The path alarms that are used in the operational status calculation for this SONET Path. pathLOP When this bit is set, path LOP is used for operational status calculation. This bit may not be mo…	Bitsr/w Enumerated Values: 0 pathLOP 1 pathAIS 2 pathRDI	.1.3.6.1.4.1.4874.2.2.7.2.3.1.7
juniSonetPathC2ByteOverrideFlag The path overhead c2 transmit override enable. If set to true(1), juniSonetPathC2Byte override value must be specified. If set to false(2), c2 byte will be automatically set by the system based on the upper interface …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.4874.2.2.7.2.3.1.8
juniSonetPathC2ByteOverride The path overhead c2 transmit and expected value for this SONET Path.	JuniSonetPathC2ByteOverrider/w Type Constraints: range: 0..255	.1.3.6.1.4.1.4874.2.2.7.2.3.1.9
juniSonetPathTriggerDelay The time delay (in milliseconds) before a defect is accepted as an alarm for this SONET Path.	msInteger32r/w Constraints: range: 0-2500	.1.3.6.1.4.1.4874.2.2.7.2.3.1.10
juniSonetPathEventStatus This variable specifies which events have occurred in the current 15 minute interval. The value represents a vector of bits, each specifying a unique event: - Bit 0 Rising threshold alarm, sonetPathCurrentESs. - Bi…	Unsigned32 Constraints: range: 0-32767	.1.3.6.1.4.1.4874.2.2.7.2.3.1.11

This table contains entries for SONET Virtual Tributary interfaces
present in the system.  This table augments the standard
SONET-MIB.sonetVTCurrentTable.

juniSonetVTEntry row .1.3.6.1.4.1.4874.2.2.7.3.2.1

Each entry describes the characteristics of an SONET Virtual Tributary
interface.

Indexes

juniSonetVTIfIndex

Column	Syntax	OID
juniSonetVTIfIndex The ifIndex of the SONET Virtual Tributary interface. When creating entries in this table, suitable values for this object are determined by reading juniSonetVTNextIfIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.4874.2.2.7.3.2.1.1
juniSonetVTPathLogicalChannel The SONET Path logical channel number associated with this virtual tributary.	JuniSonetLogicalPathChannelr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.4874.2.2.7.3.2.1.2
juniSonetVTTypedeprecated The SONET virtual tributary type. This object was deprecated because the same information is provided in the SONET-MIB.sonetVTCurrentWidth object.	JuniSonetVTTyper/w Type Values: 0 tribVT15TU11 1 tribVT20TU12 3 tribVT3 4 tribVT6 5 tribVT6c	.1.3.6.1.4.1.4874.2.2.7.3.2.1.3
juniSonetVTPathPayload The SONET Path payload number associated with this virtual tributary. For SDH mode, this is a value with a range from 1-3. For SONET mode, the value of this object is always 1.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.7.3.2.1.4
juniSonetVTTributaryGroup The SONET Path group number for this virtual tributary. In SONET and SDH mode, the value of this object is 1-7.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.7.3.2.1.5
juniSonetVTTributarySubChannel Specifies the virtual tributary number within the tributary group defined by juniSonetVTTributaryGroup object. The value of this object ranges from 1-4 if the tributary type is tribVT15/TU11(0); and the values 1-3 if t…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.4874.2.2.7.3.2.1.6
juniSonetVTLowerIfIndex The ifIndex of the interface over which this SONET Virtual Tributary interface is to be layered - typically a SONET PATH interface. A value of zero indicates no layering. An implementation may choose to …	IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647 Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits…	.1.3.6.1.4.1.4874.2.2.7.3.2.1.7
juniSonetVTRowStatus Controls creation/deletion of entries in this table according to the RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this …	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.4874.2.2.7.3.2.1.8