Juniper-UNI-ATM-MIB Table View

Column Syntax OID

The ifIndex of the ATM interface. When creating entries in this table,
suitable values for this object are determined by reading
juniAtmNextIfIndex.

Type Constraints:
range: 1..2147483647

Description:

A unique value, greater than zero, for each interface or
interface sub-layer in the managed system. It is
recommended that values are assigned contiguously starting
from 1. The value for each interface sub-layer must …

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.1

juniAtmIfRowStatus

Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

To create an entry in this …

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

The RowStatus textual convention is used to manage the
creation and deletion of conceptual rows, and is used as the
value of the SYNTAX clause for the status column of a
conceptual row (as described in Section 7.7.1 of …

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.2

juniAtmIfLowerIfIndex

The ifIndex of an interface over which this ATM interface is to be
layered. A value of zero indicates no layering. An implementation may
choose to require that a nonzero value be configured at entry creation.

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

This textual convention is an extension of the
InterfaceIndex convention. The latter defines a greater
than zero value used to identify an interface or interface
sub-layer in the managed system. This extension permits…

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.3

juniAtmIfIlmiVpi

The VPI of the ILMI of a major ATM interface.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.4

juniAtmIfIlmiVci

The VCI of the ILMI of a major ATM interface.

juniAtmIfIlmiPollFrequency

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.5

juniAtmIfIlmiVcd

An integer identifier for the ILMI, used in conjunction with the
command-line interface.

The value must be unique among VCs configured on the same ATM
interface.

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.6

The amount of time in seconds between successive transmissions of ILMI
messages on this interface for the purpose of detecting loss of ILMI
connectivity. The distinguished value zero disables ILMI connectivity
procedur…

secondsInteger32r/w

Constraints:
range: 0-65535

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.7

juniAtmIfIlmiAdminState

The administrative status of ILMI in the ATM interface.

Enumerationr/w

Enumerated Values:

0	disabled
1	enabled

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.8

juniAtmIfUniVersion

Use to specify the User Network Interface (UNI) the router should use
when ILMI link auto determination is unsuccesful or ILMI is disabled.

Enumerationr/w

Enumerated Values:

0	uniVersionAutoConfig
1	version3Dot0
2	version3Dot1
3	version4Dot0

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.9

juniAtmIfOamCellRxAdminState

Use to specify the OAM Cell Receive Administrative state on this
interface.

Enumerationr/w

Enumerated Values:

0	oamCellAdminStateDisabled
1	oamCellAdminStateEnabled

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.10

juniAtmIfInCells

The total number of cells received on this major interface.

SNMPv2-SMICounter64

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.11

juniAtmIfOutCells

The total number of cells transmitted on this major interface.

SNMPv2-SMICounter64

Type Constraints:
range: 0..18446744073709551615

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.12

juniAtmIfVcCount

The total number of circuits configured on this interface.

Integer32

Constraints:
range: 0-268431360

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.13

juniAtmIfMapGroup

The NBMA map group this interface is associated with.

JuniAtmNbmaMapNameOrNullr/w

Type Constraints:
range: 0..32

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.14

juniAtmIfCacAdminState

The administrative staus of CAC on this ATM major interface.

Juniper-TCJuniEnabler/w

Type Values:

0	disable
1	enable

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.15

juniAtmIfCacUbrWeight

The bandwidth associated with every UBR and UBR with PCR connection
configured on the ATM major interface. This value is used for CAC
computation. The units are kilo-bits per second (kbps).

kbpsInteger32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.16

juniAtmIfCacSubscriptionBandwidth

The subscribed bandwidth of the ATM major interface. If this value is
not specified or set to 0, the effective port bandwidth is used. When a
Get operation is performed the current effective bandwidth is returned.
The…

kbpsInteger32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.17

juniAtmIfCacAvailableBandwidth

The available bandwidth in Tx direction of the ATM major interface. As
connections are added or deleted on the interface, this value is
updated. The units are kilo-bits per second (kbps).

kbpsInteger32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.18

juniAtmIfCacAvailableBandwidthRxdeprecated

The available bandwidth in Rx direction of the ATM major interface. As
connections are added or deleted on the interface, this value is
updated. The units are kilo-bits per second (kbps).

kbpsInteger32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.19

juniAtmIfE164Autoconversionobsolete

The status of E164 autoconversion feature in the ATM interface.

Enumerationr/w

Enumerated Values:

0	disabled
1	enabled

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.20

juniAtmIfE164Gatewayobsolete

The status of E164 gateway feature in the ATM interface.

Enumerationr/w

Enumerated Values:

0	disabled
1	enabled

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.21

juniAtmIfE164OneToOneAddrTransobsolete

The status of E164 one-to-one address translation feature in the ATM
interface.

Enumerationr/w

Enumerated Values:

0	disabled
1	enabled

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.22

juniAtmIfOamCellFilter

The type of OAM cells to discard when juniAtmIfOamCellRxAdminState is
set to oamCellAdminStateDisabled. The value oamCellFilterAlarm discards
received OAM AIS and RDI cells. The value oamCellFilterAll discards all
rec…

Enumerationr/w

Enumerated Values:

0	oamCellFilterAll
1	oamCellFilterAlarm

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.23

juniAtmIfCacUsedBandwidthUpper

The most significant 32 bits of the CAC used bandwidth on the ATM major
interface. The least significant 32 bits of the CAC used bandwidth are
specified by juniAtmIfCacUsedBandwidthLower.

juniAtmIfCacUsedBandwidthLower

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.24

The least significant 32 bits of the CAC used bandwidth on the ATM
major interface. The most significant 32 bits of the CAC used bandwidth
are specified by juniAtmIfCacUsedBandwidthUpper.

juniAtmIfAssociatedVcClassId

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.25

The integer identifier of the ATM VC class associated with this ATM interface. A value for this identifier is determined by locating or creating an ATM VC class name in the juniAtmVcClassNameTable. A value of 0 means no…

juniAtmPvcStatsIfIndex juniAtmPvcStatsVpi juniAtmPvcStatsVci

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.2.1.26

juniAtmPvcStatisticsTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.3 · 1 row entry · 18 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmPvcStatisticsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmPvcStatisticsTable'

This table contains statistics for PVC entries.

juniAtmPvcStatisticsEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.3.1

Each entry provides statistics on an ATM PVC.

Indexes

Column	Syntax	OID
juniAtmPvcStatsIfIndex The ifIndex of the ATM interface.	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.1`
juniAtmPvcStatsVpi The VPI of the ATM VCC used by this ATM interface and PVC.	ATM-TC-MIBAtmVpIdentifier Type Constraints: `range: 0..4095`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.2`
juniAtmPvcStatsVci The VCI of the ATM VCC used by this ATM interface and PVC.	ATM-TC-MIBAtmVcIdentifier Type Constraints: `range: 0..65535`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.3`
juniAtmPvcStatsInCells Received cells.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.4`
juniAtmPvcStatsInCellOctets Received cells octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.5`
juniAtmPvcStatsInPackets Received AAL PDUs.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.6`
juniAtmPvcStatsInPacketOctets Received AAL PDU octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.7`
juniAtmPvcStatsOutCells Transmitted cells.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.8`
juniAtmPvcStatsOutCellOctets Transmitted cell octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.9`
juniAtmPvcStatsOutPackets Transmitted AAL PDUs.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.10`
juniAtmPvcStatsOutPacketOctets Transmitted AAL PDU octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.11`
juniAtmPvcStatsInCellErrors Received cells dropped due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.12`
juniAtmPvcStatsinPacketErrors Received packets dropped due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.13`
juniAtmPvcStatsOutCellErrors Cells not transmitted due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.14`
juniAtmPvcStatsOutPacketErrors Packets not transmitted due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.15`
juniAtmPvcStatsInPacketDiscards Received packets w/o errors discarded.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.16`
juniAtmPvcStatsInPacketOctetDiscards Received bytes w/o errors discarded.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.17`
juniAtmPvcStatsInPacketUnknownProtocol Received packets that are discarded because the interface can not discern or is not configured to support this protocol.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.3.1.18`

juniAtmVpTunnelTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.4 · 1 row entry · 5 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVpTunnelTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVpTunnelTable'

This table contains entries for ATM VP Tunnels present in the system.

juniAtmVpTunnelEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.4.1

Each entry describes the characteristics of an ATM VP Tunnel.

Indexes

juniAtmVpTunnelIfIndex juniAtmVpTunnelVpi

Column Syntax OID

juniAtmVpTunnelIfIndex

The ifIndex of the ATM interface. The value of this object is the same
as the juniAtmIfIndex object in the juniAtmIfTable.

Entries in this table cannot be created unless the underlying ATM
interface entr…

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.4.1.1

juniAtmVpTunnelVpi

The VPI value for this VP tunnel entry.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.1.4.1.2

juniAtmVpTunnelKbps

The tunnel rate in kilobits per second (kbps) for this entry.

kbpsInteger32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.4.1.3

juniAtmVpTunnelRowStatus

juniAtmVpTunnelServiceCategory

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.4.1.4

The ATM service category for the tunnel.

Enumerationr/w

Enumerated Values:

1	nrtVbr
2	cbr

.1.3.6.1.4.1.4874.2.2.8.1.1.4.1.5

juniAtmIfCapabilityTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.5 · 1 row entry · 9 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmIfCapabilityTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmIfCapabilityTable'

This table contains entries for ATM interfaces present in the system.

juniAtmIfCapabilityEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.5.1

Each entry describes the capabilities of an ATM interface. A
management client can use this table to determine differences in the
configurable level of support across entries in this table.

Indexes

juniAtmIfCapabilityIndex

Column Syntax OID

juniAtmIfCapabilityIndex

The ifIndex of the ATM interface. The value of this object is the same
as juniAtmIfIndex in the juniAtmIfTable.

juniAtmIfCapabilityTrafficShaping

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.1

Indicates whether traffic shaping is supported on this interface;
true(1) indicates that it is, false(2) indicates that it is not.

SNMPv2-TCTruthValue

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.2

juniAtmIfCapabilityOam

Indicates whether OAM is supported on this interface; true(1) indicates
that it is, false(2) indicates that it is not.

SNMPv2-TCTruthValue

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.3

juniAtmIfCapabilityDefaultVcPerVp

The default number of VCs per VP for this interface.

Integer32

Constraints:
range: 0-65536

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.4

juniAtmIfCapabilityNumVpiVciBits

The total range of bits used for constructing VPI/VCI identifiers for
this interface.

Integer32

Constraints:
range: 8-28

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.5

juniAtmIfCapabilityMaxVcd

The maximum configurable value for a VCD on this interface.

Integer32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.6

juniAtmIfCapabilityMaxVpi

The maximum configurable value for a VPI on this interface.

juniAtmIfCapabilityMaxVci

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.7

The maximum configurable value for a VCI on this interface.

juniAtmIfCapabilityOamCellFilter

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.8

Indicates whether OAM cell filter is supported on this interface;
true(1) indicates that it is, false(2) indicates that it is not.

SNMPv2-TCTruthValue

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.5.1.9

juniAtmIfSvcSignallingTable

table deprecated

.1.3.6.1.4.1.4874.2.2.8.1.1.6 · 1 row entry · 4 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmIfSvcSignallingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmIfSvcSignallingTable'

This table contains entries for extending the juniAtmIfTable for
configuring signalling information for switched virtual connection
(SVC).

juniAtmIfSvcSignallingEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.6.1

Each entry provides configuration parameters for ATM signalling on the
interface.

Indexes

Column Syntax OID

juniAtmIfSvcSignallingVpideprecated

The VPI identifier of the ATM circuit used for signalling for this
interface.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.1.6.1.1

juniAtmIfSvcSignallingVcideprecated

The VCI identifier of the ATM circuit used for signalling for this
interface.

ATM-TC-MIBAtmVorXAdminStatusr/w

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.1.6.1.2

juniAtmIfSvcSignallingVcddeprecated

An integer identifier for the ATM circuit used for signalling on this
interface.

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.6.1.3

juniAtmIfSvcSignallingAdminStatusdeprecated

The administrative status of signalling on the ATM interface.

Type Values:

1	up
2	down

.1.3.6.1.4.1.4874.2.2.8.1.1.6.1.4

juniAtmIfPnniRccTable

table obsolete

.1.3.6.1.4.1.4874.2.2.8.1.1.7 · 1 row entry · 4 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmIfPnniRccTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmIfPnniRccTable'

This table contains entries for extending the juniAtmIfTable for
configuring PNNI RCC information.

juniAtmIfPnniRccEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.7.1

Each entry provides configuration parameters for PNNI RCC on the
interface.

Indexes

Column Syntax OID

juniAtmIfPnniRccVpiobsolete

The VPI identifier of the ATM circuit used for PNNI RCC on this
interface.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.1.7.1.1

juniAtmIfPnniRccVciobsolete

The VCI identifier of the ATM circuit used for PNNI RCC on this
interface.

ATM-TC-MIBAtmVorXAdminStatusr/w

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.1.7.1.2

juniAtmIfPnniRccVcdobsolete

An integer identifier for the ATM circuit used for PNNI RCC on this
interface.

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.1.7.1.3

juniAtmIfPnniRccAdminStatusobsolete

The administrative status of PNNI on the ATM interface.

Type Values:

1	up
2	down

.1.3.6.1.4.1.4874.2.2.8.1.1.7.1.4

juniAtmOamF4FlowEndToEndCfgTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.8 · 1 row entry · 6 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmOamF4FlowEndToEndCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmOamF4FlowEndToEndCfgTable'

This table contains entries for F4 OAM end-to-end flows configured.

juniAtmOamF4FlowEndToEndCfgEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.8.1

Each entry provides configuration parameters for one F4 OAM end-to-end
flow configured for each VPI.

Indexes

juniAtmOamF4FlowEndToEndIfIndex juniAtmOamF4FlowEndToEndVpi

Column Syntax OID

juniAtmOamF4FlowEndToEndIfIndex

The ifIndex of the ATM interface to configure the F4 OAM end-to-end
flow.

juniAtmOamF4FlowEndToEndVpi

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.1

Select the VPI for F4 OAM end-to-end flow configuration.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.2

juniAtmOamF4FlowEndToEndLoopbackTimer

Configure the timer for sending the F4 flow end-to-end loopback OAM
cells. Setting this value will enable sending the F4 end cells on the
circuit. It is not allowed to set the value to -1 and whenever it is
read as -1 …

secondsInteger32r/w

Constraints:
range: -1-600

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.3

juniAtmOamF4FlowEndToEndCCSink

Enable/Disable F4 flow end-to-end continuity check sink end point for
this VP.

juniAtmOamF4FlowEndToEndCCSource

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.4

Enable/Disable F4 flow end-to-end continuity check source end point for
this VP.

juniAtmOamF4FlowEndToEndRowStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.5

juniAtmOamF4FlowSegmentIfIndex juniAtmOamF4FlowSegmentVpi

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.8.1.6

juniAtmOamF4FlowSegmentCfgTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.9 · 1 row entry · 5 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmOamF4FlowSegmentCfgTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmOamF4FlowSegmentCfgTable'

This table contains entries for F4 OAM Segment flows configured.

juniAtmOamF4FlowSegmentCfgEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.9.1

Each entry provides configuration parameters for one F4 OAM Segment
flow configured for each VPI.

Indexes

Column Syntax OID

juniAtmOamF4FlowSegmentIfIndex

The ifIndex of the ATM interface to configure the F4 OAM segment flow.

juniAtmOamF4FlowSegmentVpi

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.9.1.1

Select the VPI for F4 OAM segment flow configuration.

Integer32

Constraints:
range: 0-255

.1.3.6.1.4.1.4874.2.2.8.1.1.9.1.2

juniAtmOamF4FlowSegmentCCSink

Enable/Disable F4 flow segment continuity check sink end point for
this VP.

juniAtmOamF4FlowSegmentCCSource

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.9.1.3

Enable/Disable F4 flow segment continuity check source end point for
this VP.

juniAtmOamF4FlowSegmentRowStatus

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.1.9.1.4

IF-MIBifIndex ATM-MIBatmVplVpi

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.1.9.1.5

juniAtmVpDescrTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.10 · 1 row entry · 1 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVpDescrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVpDescrTable'

This table contains entries for ATM VP Description present in the
system.  The user can configure a description of up to 32 characters for
every VP in the ATM interface.  A row exists for every VP on the ATM
interface.  These rows get created as soon as the ATM major interface
created.

juniAtmVpDescrEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.10.1

Each entry contains the description of the VP.

Indexes

Column	Syntax	OID
juniAtmVpDescription The description for this VP. The default value of this object is null string.	OctetStringr/w Constraints: `range: 0-32`	`.1.3.6.1.4.1.4874.2.2.8.1.1.10.1.1`

juniAtmF4FlowOamEndToEndStatsTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.11 · 1 row entry · 20 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmF4FlowOamEndToEndStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmF4FlowOamEndToEndStatsTable'

This table contains entries for F4 flow EndToEnd OAM circuits stats.

juniAtmF4FlowOamEndToEndStatsEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.11.1

Each entry provides stats for one F4 OAM circuit for each VPI.

Indexes

juniAtmOamF4FlowEndToEndIfIndex juniAtmOamF4FlowEndToEndVpi

Column Syntax OID

juniAtmF4FlowInOamEndAisCells

Received end-to-end OAM F4 AIS cells.

juniAtmF4FlowInOamEndRdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.1

Received end-to-end OAM F4 RDI cells.

juniAtmF4FlowInOamEndCCCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.2

Received end-to-end OAM F4 CC cells.

juniAtmF4FlowInOamEndCCActDeActCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.3

Received end-to-end OAM F4 activation/de-activation cells.

juniAtmF4FlowInOamEndLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.4

Total received OAM F4 end-to-end loopback cells. Aggregate of
juniAtmF4FlowEndToEndInLoopbackCmds and
juniAtmF4FlowEndToEndInLoopbackRsps

juniAtmF4FlowOutEndRdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.5

Transmitted end-to-end OAM F4 RDI cells.

juniAtmF4FlowOutEndCCCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.6

Transmitted end-to-end OAM F4 CC cells.

juniAtmF4FlowOutEndCCActDeActCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.7

Transmitted end-to-end OAM F4 activation/de-activation cells.

juniAtmF4FlowOutEndToEndLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.8

Total transmitted OAM F4 end-to-end loopback cells. Aggregate of
juniAtmF4FlowEndToEndOutLoopbackCmds and
juniAtmF4FlowEndToEndOutLoopbackRsps

juniAtmF4FlowEndActualLoopbackFreq

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.9

Actual end-to-end loopback Frequecy calculated for OAM cells
transmission.

secondsInteger32

Constraints:
range: 0-65535

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.10

juniAtmF4FlowEndLastTimeChanged

Last time end-to-end F4 OAM flow got changed.

SNMPv2-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.11

juniAtmF4FlowOamEndVpOperationState

Represents the F4 end-to-end OAM flow VP operation states. It can take
one of the following operational state values:
vcAisState - AIS cell received or underlying physical layer
repor…

Enumeration

Enumerated Values:

0	vcAisState
1	vcRdiState
2	vcDownRetry
3	vcUpRetry
4	vcUp
5	vcDown
6	vcNotManaged
7	vpAisState
8	vpRdiState
9	vcInVpRdiState
10	vcInVpAisState
11	vcSegmentAisState
12	vcSegRdiState

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.12

juniAtmF4FlowOamEndVpAdminState

End-to-end VP admin state.

Enumeration

Enumerated Values:

0	down
1	up

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.13

juniAtmF4FlowEndInOamCells

Received end-to-end OAM F4 loopback cells.

juniAtmF4FlowEndOutOamCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.14

Transmitted end-to-end OAM F4 loopback cells.

juniAtmF4FlowEndInOamCellsDropped

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.15

Received end-to-end OAM cells that were dropped.

juniAtmF4FlowEndToEndInLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.16

Received OAM F4 end-to-end loopback commands.

juniAtmF4FlowEndToEndInLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.17

Received OAM F4 end-to-end loopback responses.

juniAtmF4FlowEndToEndOutLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.18

Transmitted OAM F4 end-to-end loopback commands.

juniAtmF4FlowEndToEndOutLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.19

Transmitted OAM F4 end-to-end loopback responses.

juniAtmOamF4FlowSegmentIfIndex juniAtmOamF4FlowSegmentVpi

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.11.1.20

juniAtmF4FlowOamSegmentStatsTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.12 · 1 row entry · 19 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmF4FlowOamSegmentStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmF4FlowOamSegmentStatsTable'

This table contains entries for F4 flow Segment OAM circuits stats.

juniAtmF4FlowOamSegmentStatsEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.12.1

Each entry provides stats for one F4 OAM circuit for each VPI.

Indexes

Column Syntax OID

juniAtmF4FlowInOamSegmentAisCells

Received end-to-end OAM F4 AIS cells.

juniAtmF4FlowInOamSegmentRdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.1

Received end-to-end OAM F4 RDI cells.

juniAtmF4FlowInOamSegmentCCCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.2

Received end-to-end OAM F4 CC cells.

juniAtmF4FlowInOamSegmentCCActDeActCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.3

Received end-to-end OAM F4 activation/de-activation cells.

juniAtmF4FlowInOamSegmentLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.4

Total received OAM F4 segment loopback cells. Aggregate of
juniAtmF4FlowSegmentInLoopbackCmds and
juniAtmF4FlowSegmentInLoopbackRsps

juniAtmF4FlowOutSegmentRdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.5

Transmitted end-to-end OAM F4 RDI cells.

juniAtmF4FlowOutSegmentCCCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.6

Transmitted end-to-end OAM F4 CC cells.

juniAtmF4FlowOutSegmentCCActDeActCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.7

Transmitted end-to-end OAM F4 activation/de-activation cells.

juniAtmF4FlowOutSegmentLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.8

Total transmitted OAM F4 segment loopback cells. Aggregate of
juniAtmF4FlowSegmentOutLoopbackCmds and
juniAtmF4FlowSegmentOutLoopbackRsps

juniAtmF4FlowSegmentLastTimeChanged

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.9

Last time end-to-end F4 OAM flow got changed.

SNMPv2-SMITimeTicks

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.10

juniAtmF4FlowOamSegmentVpOperationState

Represents the F4 end-to-end OAM flow VP operation states. It can take
one of the following operational state values:
vcAisState - AIS cell received or underlying physical layer
repor…

Enumeration

Enumerated Values:

0	vcAisState
1	vcRdiState
2	vcDownRetry
3	vcUpRetry
4	vcUp
5	vcDown
6	vcNotManaged
7	vpAisState
8	vpRdiState
9	vcInVpRdiState
10	vcInVpAisState
11	vcSegmentAisState
12	vcSegRdiState

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.11

juniAtmF4FlowOamSegmentVpAdminState

Segment VP admin state.

Enumeration

Enumerated Values:

0	down
1	up

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.12

juniAtmF4FlowSegmentInOamCells

Received end-to-end OAM F4 loopback cells.

juniAtmF4FlowSegmentOutOamCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.13

Transmitted end-to-end OAM F4 loopback cells.

juniAtmF4FlowSegmentInOamCellsDropped

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.14

Received end-to-end OAM cells that were dropped.

juniAtmF4FlowSegmentInLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.15

Received OAM F4 segment loopback commands.

juniAtmF4FlowSegmentInLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.16

Received OAM F4 segment loopback responses.

juniAtmF4FlowSegmentOutLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.17

Transmitted OAM F4 segment loopback commands.

juniAtmF4FlowSegmentOutLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.18

Transmitted OAM F4 segment loopback responses.

juniAtmMartiniTimeoutTimerIndex

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.1.12.1.19

juniAtmMartiniTimeoutTimerTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.13 · 1 row entry · 2 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmMartiniTimeoutTimerTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmMartiniTimeoutTimerTable'

This table contains entries for ATM Martini cell aggregation timeout
detection.  The user can configure timeout values for three timers.
A row exists for every separate timer supported.  These rows get 
created as soon as the ERX system comes up.

juniAtmMartiniTimeoutTimerEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.13.1

Each entry contains the timeout value of ATM Martini
cell aggregation timer.

Indexes

Column Syntax OID

juniAtmMartiniTimeoutTimerIndex

The ATM Martini cell aggregation timeout timer identifier.

Enumeration

Enumerated Values:

1	timer1
2	timer2
3	timer3

.1.3.6.1.4.1.4874.2.2.8.1.1.13.1.1

juniAtmMartiniTimeoutTimerValue

The ATM Martini cell aggregation timeout timer value in microseconds.

Integer32r/w

Constraints:
range: 100-4095

.1.3.6.1.4.1.4874.2.2.8.1.1.13.1.2

juniAtmVpStatsTable

table

.1.3.6.1.4.1.4874.2.2.8.1.1.14 · 1 row entry · 16 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVpStatsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVpStatsTable'

This table contains entries for ATM VP statistics present in the
system. A row exists for every VP on the ATM
interface. These rows get created as soon as the ATM major interface
created.

juniAtmVpStatsEntry row .1.3.6.1.4.1.4874.2.2.8.1.1.14.1

Each entry contain the VP statistics.

Indexes

IF-MIBifIndex ATM-MIBatmVplVpi

Column	Syntax	OID
juniAtmVpStatsIfIndex The ifIndex of the ATM interface.	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.1`
juniAtmVpStatsVpi The VPI value of the virtual path for which statistics are retrieved.	ATM-TC-MIBAtmVpIdentifier Type Constraints: `range: 0..4095`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.2`
juniAtmVpStatsInCells Received cells.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.3`
juniAtmVpStatsInPackets Received AAL5 PDUs.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.4`
juniAtmVpStatsInPacketOctets Received AAL5 PDU octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.5`
juniAtmVpStatsOutCells Transmitted cells.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.6`
juniAtmVpStatsOutPackets Transmitted AAL5 PDUs	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.7`
juniAtmVpStatsOutPacketOctets Transmitted AAL5 PDU octets.	SNMPv2-SMICounter64 Type Constraints: `range: 0..18446744073709551615`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.8`
juniAtmVpStatsInPacketErrors Received packets dropped due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.9`
juniAtmVpStatsOutPacketErrors Packets not transmitted due to errors.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.10`
juniAtmVpStatsInPacketDiscards Received packets without errors discarded.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.11`
juniAtmVpStatsInPacketOctetDiscards Received bytes without errors discarded.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.12`
juniAtmVpStatsInPacketUnknownProtocol Received packets that are discarded because the interface can not discern or is not configured to support this protocol.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.13`
juniAtmVpStatsCrcErrors Received packets that are discarded because of check sum erros	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.14`
juniAtmVpStatsSarTimeouts Received packets that are discarded because of SAR timeout	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.15`
juniAtmVpStatsOverSizedPackets Over sized packets that are received on this VP.	SNMPv2-SMICounter32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.1.14.1.16`

juniAtmAal5IfTable

table

.1.3.6.1.4.1.4874.2.2.8.1.2.2 · 1 row entry · 3 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmAal5IfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmAal5IfTable'

This table contains entries for ATM AAL5 interfaces present in the
system.

juniAtmAal5IfEntry row .1.3.6.1.4.1.4874.2.2.8.1.2.2.1

Each entry describes the characteristics of an ATM AAL5 interface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniAtmAal5IfIndex

Column Syntax OID

juniAtmAal5IfIndex

The ifIndex of the ATM AAL5 interface. When creating entries in this
table, suitable values for this object are determined by reading
juniAtmAal5NextIfIndex.

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.2.1.1

juniAtmAal5IfRowStatus

juniAtmAal5IfLowerIfIndex

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.2.1.2

The ifIndex of an ATM interface over which this ATM AAL5 interface is
to be layered. A value of zero indicates no layering. An
implementation may choose to require that a nonzero value be configured
at entry creation.

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.2.1.3

juniAtmBulkCircuitsNameTable

table

.1.3.6.1.4.1.4874.2.2.8.1.2.3 · 1 row entry · 4 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmBulkCircuitsNameTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmBulkCircuitsNameTable'

The entries in this table provide mappings of ATM bulk virtual circuit
range names to local integer identifiers for those profiles. These
integers are used as indexes into other MIB tables containing profile
configuration parameters associated with the same profile name.

juniAtmBulkCircuitsNameEntry row .1.3.6.1.4.1.4874.2.2.8.1.2.3.1

A mapping of a ATM bulk virtual circuit range name to an integer
identifier for that name.

Indexes

juniAtmBulkCircuitsNameAal5IfIndex juniAtmBulkCircuitsNameName

Column Syntax OID

juniAtmBulkCircuitsNameAal5IfIndex

The ifIndex of the ATM AAL5 interface.

juniAtmBulkCircuitsNameName

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.3.1.1

The ATM bulk virtual circuit range name uniquely identifying this
entry.

OctetString

Constraints:
range: 1-80

.1.3.6.1.4.1.4874.2.2.8.1.2.3.1.2

juniAtmBulkCircuitsNameRowStatus

Controls creation/deletion of entries in this table. Only the values
'createAndGo' and 'destroy' may be SET.

Creating an entry in this table creates corresponding entry in
juniAtmBulkCircuitsIdTable. Del…

juniAtmBulkCircuitsNameId

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.3.1.3

The integer identifier associated with this ATM bulk virtual circuit
range name.

This value of this identifier is assigned by the device when an entry in
this table is created.

juniAtmBulkCircuitsIdAal5IfIndex juniAtmBulkCircuitsIdId

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.2.3.1.4

juniAtmBulkCircuitsIdTable

table

.1.3.6.1.4.1.4874.2.2.8.1.2.4 · 1 row entry · 4 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmBulkCircuitsIdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmBulkCircuitsIdTable'

Provides inverse mapping of ATM bulk virtual circuit IDs to ATM bulk
virtual circuit names.

juniAtmBulkCircuitsIdEntry row .1.3.6.1.4.1.4874.2.2.8.1.2.4.1

A mapping of an integer identifier to a ATM bulk virtual circuit name.

Indexes

Column	Syntax	OID
juniAtmBulkCircuitsIdAal5IfIndex The ifIndex of the ATM AAL5 interface.	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.4874.2.2.8.1.2.4.1.1`
juniAtmBulkCircuitsIdId The integer identifier associated with this ATM bulk virtual circuit name.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.2.4.1.2`
juniAtmBulkCircuitsIdName The ATM bulk virtual circuit name having the associated identifier.	OctetString Constraints: `range: 1-80`	`.1.3.6.1.4.1.4874.2.2.8.1.2.4.1.3`
juniAtmBulkCircuitsIdNextInstance The next available instance value for juniAtmBulkCircuitsEntry.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.2.4.1.4`

juniAtmBulkCircuitsTable

table

.1.3.6.1.4.1.4874.2.2.8.1.2.5 · 1 row entry · 9 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmBulkCircuitsTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmBulkCircuitsTable'

This table contains bulk virtual circuit range parameters.

juniAtmBulkCircuitsEntry row .1.3.6.1.4.1.4874.2.2.8.1.2.5.1

Each entry describes the characteristics of VC range.

Indexes

juniAtmBulkCircuitsAal5IfIndex juniAtmBulkCircuitsId juniAtmBulkCircuitsInstance

Column Syntax OID

juniAtmBulkCircuitsAal5IfIndex

The ifIndex of the ATM AAL5 interface on which this bulk virtual
circuit sub-range is created.

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.1

juniAtmBulkCircuitsId

The integer identifier associated with this ATM bulk virtual circuit
name.

juniAtmBulkCircuitsInstance

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.2

The unique identifier of the ATM bulk virtual circuit sub-range.

juniAtmBulkCircuitsRowStatus

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.3

Controls creation/deletion of entries in this table. Only the values
'createAndGo' and 'destroy' may be SET.

Since none of the VPI/VCI minimum and maximum values have default
values, all these values mus…

juniAtmBulkCircuitsMinVpi

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.4

The minimum value of VPI for this circuit sub-range. This value must
be less than or equal to the value of juniAtmBulkCircuitsMaxVpi.

juniAtmBulkCircuitsMaxVpi

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.5

The maximum value of VPI for this cicuit sub-range. This value must
be equal to or greater than the value of juniAtmBulkCircuitsMinVpi.

juniAtmBulkCircuitsMinVci

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.6

The minimum value of VCI for this circuit sub-range. This value must
be less than or equal to the value of juniAtmBulkCircuitsMaxVci.

juniAtmBulkCircuitsMaxVci

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.7

The maximum value of VCI for this circuit sub-range. This value must
be equal to or greater than the value of juniAtmBulkCircuitsMinVci.

juniAtmBulkCircuitsAdminState

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.8

The administrative status of this circuit sub-range.

Juniper-TCJuniEnabler/w

Type Values:

0	disable
1	enable

.1.3.6.1.4.1.4874.2.2.8.1.2.5.1.9

juniAtmProfileOverrideAssignIfCircuitTable

table

.1.3.6.1.4.1.4874.2.2.8.1.2.6 · 1 row entry · 7 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmProfileOverrideAssignIfCircuitTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmProfileOverrideAssignIfCircuitTable'

Table providing overriding profile assignment to a circuit configured 
as part of bulk-configuration. Circuit is identified by interface index 
and vpi, vci.
          
The entries in this table specify which profile to use when creating and
configuring a dynamic interface above a circuit specified by vpi and 
vci.
          
This entry is effective when the circuit specified by 
juniAtmProfileOverrideAssignIfCircuitAal5Index, 
juniAtmProfileOverrideAssignIfCircuitRangeId,             
juniAtmProfileOverrideAssignIfCircuitVpi, 
juniAtmProfileOverrideAssignIfCircuitVci 
		is part of bulk-configuration.

juniAtmProfileOverrideAssignIfCircuitEntry row .1.3.6.1.4.1.4874.2.2.8.1.2.6.1

An assignment of a profile to a circuit configured as part of
bulk-configuration on an AAL5 interface.

Indexes

juniAtmProfileOverrideAssignIfCircuitAal5Index juniAtmProfileOverrideAssignIfCircuitRangeId juniAtmProfileOverrideAssignIfCircuitVpi juniAtmProfileOverrideAssignIfCircuitVci

Column Syntax OID

juniAtmProfileOverrideAssignIfCircuitAal5Index

The ifIndex of the AAL5 interface to which the profile is assigned.

juniAtmProfileOverrideAssignIfCircuitRangeId

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.1

The integer identifier associated with the ATM bulk circuit
configuration.

juniAtmProfileOverrideAssignIfCircuitVpi

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.2

The VPI value of the circuit to which the profile is assigned.

juniAtmProfileOverrideAssignIfCircuitVci

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.3

The VCI value of the circuit to which the profile is assigned.

juniAtmProfileOverrideAssignIfCircuitRowStatus

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.4

Controls creation/deletion of entries in this table. Only the values
'createAndGo' and 'destroy' may be SET.

Since the VPI, VCI and profileId values do not have any default
values, all these values must …

juniAtmProfileOverrideAssignIfCircuitProfileId

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.5

The ID of the profile assigned to the circuit configured as part of
bulk-configuration. Circuit is identified by interface index and vpi,
vci.

juniAtmProfileOverrideAssignIfCircuitOperStatus

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.6

The operational status of the profile override assignment identified
by this entry.

It returns inactive(0), if a static ATM circuit with identical VPI/VCI
values is present on the same ATM interface. In …

Enumeration

Enumerated Values:

0	inactive
1	active

.1.3.6.1.4.1.4874.2.2.8.1.2.6.1.7

juniAtmSubIfTable

table

.1.3.6.1.4.1.4874.2.2.8.1.3.2 · 1 row entry · 11 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmSubIfTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmSubIfTable'

This table contains entries for ATM Subinterfaces present in the
system.

juniAtmSubIfEntry row .1.3.6.1.4.1.4874.2.2.8.1.3.2.1

Each entry describes the characteristics of an ATM Subinterface.
Creating/deleting entries in this table causes corresponding entries for
be created/deleted in ifTable/ifXTable/juniIfTable.

Indexes

juniAtmSubIfIndex

Column Syntax OID

juniAtmSubIfIndex

The ifIndex of the ATM Subinterface. When creating entries in this
table, suitable values for this object are determined by reading
juniAtmSubNextIfIndex.

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.1

juniAtmSubIfRowStatus

juniAtmSubIfDistinguisher

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.2

An integer identifier for the subinterface, used in conjunction with
the command-line interface. It is provided here for cross-reference
purposes only.

The value must be unique among subinterfaces config…

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.3

juniAtmSubIfLowerIfIndex

The ifIndex of an ATM AAL5 interface over which this ATM subinterface
is to be layered. A value of zero indicates no layering. An
implementation may choose to require that a nonzero value be configured
at entry creati…

IF-MIBInterfaceIndexOrZeror/w

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.4

juniAtmSubIfNbma

The NBMA administrative setting. Setting this value of this object to
true(1) will enable multipoint access on this interface. Setting the
value to false(2), will enable point to point access on this interface.

juniAtmSubIfAdvisoryRxSpeed

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.5

juniAtmSubIfAddressdeprecated

Specifies the local ATM NSAP address of the circuit. A GET operation
returns a full 20-octet NSAP. A SET operation only requires 7 octets,
since the prefix can be implied.

OctetStringr/w

Constraints:
range: 0-0
range: 7-7
range: 20-20

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.6

juniAtmSubIfMtu

The size of the largest packet which can be sent/received on the
interface, specified in octets.

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.7

Advisory receive speed, in kilobits per second (kbps),
of this subinterface. This object has no impact on
forwarding performance but may be used as a hint for
underlying circuit receive speed.

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.8

juniAtmSubIfMartiniMaxCellsPerPacket

The number of cells that can be aggregated in a single ATM Martini
packet in cell-relay mode.

Integer32r/w

Constraints:
range: 1-190

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.9

juniAtmSubIfMartiniTimeoutTimerId

The timer identifier used to abandon cell aggregation when no
cells are supplied for transmission in ATM Martini cell-relay mode.

Integer32r/w

Constraints:
range: 1-3

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.10

juniAtmSubIfAssociatedVcClassId

The integer identifier of the ATM VC class associated with this ATM
sub interface. A value for this identifier is determined by locating or
creating an ATM VC class name in the juniAtmVcClassNameTable. A value of 0
m…

juniAtmSubIfIndex juniAtmSubIfVccVpi juniAtmSubIfVccVci

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.2.1.11

juniAtmSubIfVccTable

table

.1.3.6.1.4.1.4874.2.2.8.1.3.3 · 1 row entry · 12 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmSubIfVccTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmSubIfVccTable'

This table contains entries for ATM VCCs configured on ATM
subinterfaces present in the system.
          
An implementation may constrain the number of VCCs permitted to be
configured per ATM Subinterface; in particular, an implementation may
restrict each ATM Subinterface to have a single VCC.
          
Attributes in this entry can only be configured at entry creation, and
remain fixed for the lifetime of the entry.

juniAtmSubIfVccEntry row .1.3.6.1.4.1.4874.2.2.8.1.3.3.1

Each entry describes the characteristics of an ATM subinterface VCC.

Indexes

Column Syntax OID

juniAtmSubIfVccVpi

The VPI of the ATM VCC used by this subinterface.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.1

juniAtmSubIfVccVci

The VCI of the ATM VCC used by this subinterface.

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.2

juniAtmSubIfVccRowStatus

juniAtmSubIfVccServiceCategory

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.3

juniAtmSubIfVccVcd

An integer identifier for the circuit, used in conjunction with the
command-line interface. It is provided here for cross-reference
purposes only.

The value must be unique among VCCs configured on the sa…

Integer32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.4

juniAtmSubIfVccType

Specifies the encapsulation used by the circuit to carry IP datagrams.
Encapsulations are as specified in RFC1483 Multiprotocol Interconnect
over ATM. The 'autoconfig' value will recognize both VcMux and LLC
formats. …

Enumerationr/w

Enumerated Values:

0	rfc1483VcMux
1	rfc1483Llc
2	autoconfig
3	aal5
4	aal0

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.5

Service category for this circuit:
ubr Unspecified Bit Rate (best effort).
ubrPcr Unspecified Bit Rate with Peak Cell Rate limit.
nrtVbr Non-RealTime Variable Bit Rate.
cbr Constant Bit Rate.
r…

Enumerationr/w

Enumerated Values:

0	ubr
1	ubrPcr
2	nrtVbr
3	cbr
4	rtVbr

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.6

juniAtmSubIfVccPcr

Peak Cell Rate, in kilobits per second (kbps), of this circuit.

This parameter is only required when juniAtmSubIfVccServiceCategory is
configured to have one of the following values:
ubrPcr
nrtVbr…

kbpsInteger32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.7

juniAtmSubIfVccScr

Sustained Cell Rate, in kilobits per second (kbps), of this circuit.

This parameter is only required when juniAtmSubIfVccServiceCategory is
configured to have the following value:
nrtVbr
rtVbr

kbpsInteger32r/w

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.8

juniAtmSubIfVccMbs

Maximum Burst Size, in cells, of this circuit.

This parameter is only required when juniAtmSubIfVccServiceCategory is
configured to have the following value:
nrtVbr
rtVbr

cellsInteger32r/w

Constraints:
range: 0-16777215

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.9

juniAtmSubIfInverseArp

Enables the inverse ARP protocol on this VCC; true(1) enables the
protocol, false(2) disables it.

juniAtmSubIfInverseArpRefresh

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.10

The refresh rate in minutes between inverse ARP protocol messages.

minutesInteger32r/w

Constraints:
range: 0-60

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.11

juniAtmSubIfVccAssociatedVcClassId

juniAtmCircuitOamIfIndex juniAtmCircuitOamVpi juniAtmCircuitOamVci

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.3.1.12

juniAtmCircuitOamTable

table

.1.3.6.1.4.1.4874.2.2.8.1.3.4 · 1 row entry · 30 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmCircuitOamTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmCircuitOamTable'

This table contains circuit OAM data for a PVC.

juniAtmCircuitOamEntry row .1.3.6.1.4.1.4874.2.2.8.1.3.4.1

Each entry provides OAM data on an ATM PVC.

Indexes

Column Syntax OID

juniAtmCircuitOamIfIndex

The ifIndex of the ATM subinterface.

Type Constraints:
range: 1..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.1

juniAtmCircuitOamVpi

The VPI of the ATM VCC used by this ATM interface and PVC.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.2

juniAtmCircuitOamVci

The VCI of the ATM VCC used by this ATM interface and PVC.

juniAtmCircuitOamAdminStatus

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.3

The administrative state of OAM for the interface identified by this
entry.

Enumerationr/w

Enumerated Values:

1	oamAdminStateDisabled
2	oamAdminStateEnabled

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.4

juniAtmCircuitOamLoopbackOperStatus

The operational status of OAM for the interface identified by this
entry.
oamOperStatusNotSupported(0) - OAM not supported on this interface
oamOperStatusDisabled(1) - VC integrity disabled
oamOperStatus…

Enumeration

Enumerated Values:

0	oamOperStatusNotSupported
1	oamOperStatusDisabled
2	oamOperStatusSent
3	oamOperStatusReceived
4	oamOperStatusFailed

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.5

juniAtmCircuitVcOamOperStatus

The OAM VC operational status of this entry.
oamVcOperStateAisState(0) - AIS cell received or underlying
physical layer reporting transmission
path AIS
oamVcOpe…

Enumeration

Enumerated Values:

0	oamVcOperStateAisState
1	oamVcOperStateRdiState
2	oamVcOperStateDownRetry
3	oamVcOperStateUpRetry
4	oamVcOperStateUp
5	oamVcOperStateDown
6	oamVcOperStateNotManaged
7	oamVcOperStateVpAis
8	oamVcOperStateVpRdi
9	oamVcOperStateVcInVpRdi
10	oamVcoperStateVcInVpAis
11	oamVcOperStateSegAis
12	oamVcOperStateSegRdi
13	oamVcOperStateGenAis

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.6

juniAtmCircuitOamLoopbackFrequency

The OAM loopback frequency in seconds.

secondsInteger32r/w

Constraints:
range: 1-600

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.7

juniAtmCircuitInOamF5Cells

Received OAM F5 cells.

juniAtmCircuitInOamCellsDropped

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.8

Received OAM cells that were dropped.

juniAtmCircuitOutOamF5Cells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.9

Transmitted OAM F5 cells.

juniAtmCircuitInOamF5EndToEndLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.10

Total received OAM F5 end-to-end loopback cells. Aggregate of
juniAtmCircuitInOamF5EndToEndLoopbackCmds and
juniAtmCircuitInOamF5EndToEndLoopbackRsps

juniAtmCircuitInOamF5SegmentLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.11

Total received OAM F5 segment loopback cells. Aggregate of
juniAtmCircuitInOamF5SegmentLoopbackCmds and
juniAtmCircuitInOamF5SegmentLoopbackRsps

juniAtmCircuitInOamF5AisCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.12

Received OAM F5 AIS cells.

juniAtmCircuitInOamF5RdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.13

Received OAM F5 RDI cells.

juniAtmCircuitOutOamF5EndToEndLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.14

Total transmitted OAM F5 end-to-end loopback cells. Aggregate of
juniAtmCircuitOutOamF5EndToEndLoopbackCmds and
juniAtmCircuitOutOamF5EndToEndLoopbackRsps

juniAtmCircuitOutOamF5SegmentLoopbackCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.15

Total transmitted OAM F5 segment loopback cells. Aggregate of
juniAtmCircuitOutOamF5SegmentLoopbackCmds and
juniAtmCircuitOutOamF5SegmentLoopbackRsps

juniAtmCircuitOutOamF5RdiCells

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.16

Transmitted OAM F5 RDI cells.

juniAtmCircuitInOamF5EndToEndLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.17

Received OAM F5 end-to-end loopback commands.

juniAtmCircuitInOamF5EndToEndLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.18

Received OAM F5 end-to-end loopback responses.

juniAtmCircuitInOamF5SegmentLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.19

Received OAM F5 segment loopback commands.

juniAtmCircuitInOamF5SegmentLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.20

Received OAM F5 segment loopback responses.

juniAtmCircuitOutOamF5EndToEndLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.21

Transmitted OAM F5 end-to-end loopback commands.

juniAtmCircuitOutOamF5EndToEndLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.22

Transmitted OAM F5 end-to-end loopback responses.

juniAtmCircuitOutOamF5SegmentLoopbackCmds

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.23

Transmitted OAM F5 segment loopback commands.

juniAtmCircuitOutOamF5SegmentLoopbackRsps

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.24

Transmitted OAM F5 segment loopback responses.

juniAtmCircuitOamDownCount

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.25

juniAtmCircuitOamUpCount

Specifies the number of successive loopback cell responses to receive
before a PVC is up for connectivity verification.

cellsInteger32r/w

Constraints:
range: 1-60

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.26

Specifies the number of successive loopback cell responses not received
before declaring a PVC down for connectivity verification.

cellsInteger32r/w

Constraints:
range: 1-60

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.27

juniAtmCircuitOamRetryFrequency

Specifies the frequency (in seconds) to transmit loopback cells when
verifying PVC state (up or down) for connectivity verification.

secondsInteger32r/w

Constraints:
range: 1-600

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.28

juniAtmCircuitOamAlarmDownCount

Specifies the number of successive alarm (AIS or RDI) cells to receive
before declaring a PVC down.

cellsInteger32r/w

Constraints:
range: 1-60

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.29

juniAtmCircuitOamAlarmClearTimeout

Specifies how long to wait (in seconds) before declaring a PVC up after
it has stopped receiving alarm cells.

secondsInteger32r/w

Constraints:
range: 3-60

.1.3.6.1.4.1.4874.2.2.8.1.3.4.1.30

juniAtmSubIfVccTrafficShapingTable

table

.1.3.6.1.4.1.4874.2.2.8.1.3.5 · 1 row entry · 5 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmSubIfVccTrafficShapingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmSubIfVccTrafficShapingTable'

This table contains entries for traffic shaping of ATM VCCs configured
on ATM subinterfaces present in the system. This table augments the
juniAtmSubIfVccTable only for VCCs that support traffic shapping.

Attributes in this entry can only be configured at entry creation, and
remain fixed for the lifetime of the entry.

juniAtmSubIfVccTrafficShapingEntry row .1.3.6.1.4.1.4874.2.2.8.1.3.5.1

Each entry describes the traffic shping characteristics of an ATM
subinterface VCC.

Indexes

No indexes recorded

Column Syntax OID

juniAtmSubIfVccTrafficShapingCdvt

The network cell delay variation tolerance (CDVT) in tenths of a
microsecond.

tenths of a microsecondSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.5.1.1

juniAtmSubIfVccTrafficShapingClp0

Specifies whether or not only CLP0 cells are to be policed according to
the traffic contract. CLP1 cells are forwarded on a best-effort basis
CLP-significant model for (VBR.2, VBR.3 conformance). Applicable only
for V…

juniAtmSubIfVccTrafficShapingTagging

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.5.1.2

Specifies whether or not CLP0 cells should be tagged for SCR policing
(VBR.3 conformance). Applicable only for VBR circuits.

juniAtmSubIfVccTrafficShapingPoliceObserve

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.5.1.3

Specifies whether of not no policing action is to be taken (note the
double negative; if true(1) then no policing action will be taken; if
false(2) then policing action will be taken). Regardless of the state
of this o…

juniAtmSubIfVccTrafficShapingPacketShaping

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.5.1.4

Specifies whether of not to shape output traffic on a packet boundary.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.5.1.5

juniAtmSubIfSvcConfigTable

table deprecated

.1.3.6.1.4.1.4874.2.2.8.1.3.6 · 1 row entry · 13 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmSubIfSvcConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmSubIfSvcConfigTable'

This table contains entries for extending the juniAtmSubIfTable to
configure switched virtual connection (SVC) on the subinterfaces.

juniAtmSubIfSvcConfigEntry row .1.3.6.1.4.1.4874.2.2.8.1.3.6.1

Each entry provides configuration parameters for an ATM SVC on the
subinterface.

Indexes

juniAtmSubIfIndex

Column Syntax OID

juniAtmSubIfSvcRowStatusdeprecated

Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.1

juniAtmSubIfSvcConfigDestAtmAddressdeprecated

Specifies the destination ATM NSAP address of the circuit.

OctetStringr/w

Constraints:
range: 20-20

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.2

juniAtmSubIfSvcConfigCircuitTypedeprecated

Specifies the encapsulation used by the circuit to carry IP datagrams.
Encapsulations are as specified in RFC1483 Multiprotocol Interconnect
over ATM.

Enumerationr/w

Enumerated Values:

0	rfc1483VcMux
1	rfc1483Llc

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.3

juniAtmSubIfSvcConfigServiceCategorydeprecated

Service category for this circuit:
ubr Unspecified Bit Rate (best effort).
ubrPcr Unspecified Bit Rate with Peak Cell Rate limit.
nrtVbr Non-RealTime Variable Bit Rate.
cbr Constant Bit Rate.
r…

Enumerationr/w

Enumerated Values:

0	ubr
1	ubrPcr
2	nrtVbr
3	cbr
4	rtVbr

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.4

juniAtmSubIfSvcConfigPcrdeprecated

Peak Cell Rate, in kilo-bits per second (kbps), of this circuit.

kbpsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.5

juniAtmSubIfSvcConfigScrdeprecated

Sustained Cell Rate, in kilo-bits per second (kbps), of this circuit.

kbpsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.6

juniAtmSubIfSvcConfigMbsdeprecated

Maximum Burst Size, in cells, of this circuit.

cellsSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.7

juniAtmSubIfSvcConfigCdvtobsolete

Specify the network Cell Delay Variation Tolerance.

100usSNMPv2-SMIUnsigned32r/w

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.8

juniAtmSubIfSvcConfigClp0deprecated

Specify that only CLP0 cells are to be policed according to the traffic
contract. CLP1 cells are forwarded on a best-effort basis
CLP-significant model for (VBR.2, VBR.3 conformance).

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.9

juniAtmSubIfSvcConfigTaggingdeprecated

Specify that CLP0 cells should be tagged for SCR policing (VBR.3
conformance).

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.10

juniAtmSubIfSvcConfigObserveobsolete

Specify that no policing action is to be taken; only counters are
incremented.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.11

juniAtmSubIfSvcConfigPacketDiscarddeprecated

Enable early packet Discard for this circuit.

juniAtmNbmaMapName juniAtmNbmaMapVcd

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.12

juniAtmSubIfSvcConfigDestE164Addressobsolete

Specifies the destination ATM E164 address of the circuit.

OctetStringr/w

Constraints:
range: 0-0
range: 8-8

.1.3.6.1.4.1.4874.2.2.8.1.3.6.1.13

juniAtmNbmaMapTable

table

.1.3.6.1.4.1.4874.2.2.8.1.4.1 · 1 row entry · 8 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmNbmaMapTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmNbmaMapTable'

This table contains entries for ATM NBMA maps.

juniAtmNbmaMapEntry row .1.3.6.1.4.1.4874.2.2.8.1.4.1.1

Each entry describes the characteristics of an ATM NBMA map.

Indexes

Column Syntax OID

juniAtmNbmaMapName

The NBMA map name.

JuniAtmNbmaMapName

Type Constraints:
range: 1..32

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.1

juniAtmNbmaMapVcd

An integer identifier for the ATM circuit, used in conjunction with the
command-line interface.

The value must be unique among VCs configured on the same ATM
interface.

Integer32

Constraints:
range: 0-2147483647

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.2

juniAtmNbmaMapIpAddress

The IP address associated with this entry.

SNMPv2-SMIIpAddressr/w

Type Constraints:
range: 4

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.3

juniAtmNbmaMapVpi

The VPI identifier of the ATM circuit.

Type Constraints:
range: 0..4095

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.4

juniAtmNbmaMapVci

The VCI identifier of the ATM circuit.

IF-MIBInterfaceIndexOrZero

Type Constraints:
range: 0..65535

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.5

juniAtmNbmaMapIfIndex

The ifIndex of the ATM major interface associated with this entry.
The value of this object will be zero when the map is not applied
to an interface.

Type Constraints:
range: 0..2147483647

Description:

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.6

juniAtmNbmaMapBroadcast

The broadcast enable/disable setting for this entry. The value true(1)
enable broadcast support; disable(2) disabled broadcast support for this
entry.

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.7

juniAtmNbmaMapRowStatus

Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

Additional notes to aid the…

juniAtmNbmaMapListRowStatus

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.4.1.1.8

juniAtmNbmaMapListTable

table

.1.3.6.1.4.1.4874.2.2.8.1.4.2 · 1 row entry · 2 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmNbmaMapListTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmNbmaMapListTable'

This table contains entries for ATM NBMA map lists.

juniAtmNbmaMapListEntry row .1.3.6.1.4.1.4874.2.2.8.1.4.2.1

Each entry describes the characteristics of an ATM NBMA map.

Indexes

juniAtmNbmaMapListName

Column Syntax OID

juniAtmNbmaMapListName

The NBMA Map List name.

JuniAtmNbmaMapName

Type Constraints:
range: 1..32

.1.3.6.1.4.1.4874.2.2.8.1.4.2.1.1

Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following
values only:
createAndGo
destroy

IF-MIBifIndex ATM-MIBatmVplVpi ATM-FORUM-SNMP-M4-MIBatmfM4VpTestObject

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.4.2.1.2

juniAtmVpPingTable

table

.1.3.6.1.4.1.4874.2.2.8.1.5.2 · 1 row entry · 9 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVpPingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVpPingTable'

This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB
atmM4VpTestTable to do ping (multiple loopback) type testing.

juniAtmVpPingEntry row .1.3.6.1.4.1.4874.2.2.8.1.5.2.1

Each entry describes the characteristics, status and results of the
most recent ATM ping test.

Indexes

Column Syntax OID

juniAtmVpPingProbeCount

The number of ping probes (OAM cells) to be sent to complete the test.

probesUnsigned32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.1

juniAtmVpPingTimeOut

Specifies the time-out value, in seconds, for a remote ping operation.

secondsUnsigned32r/w

Constraints:
range: 1-5

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.2

juniAtmVpPingCtlTrapGeneration

The value of this object determines when and if to generate a
notification for this entry:

testCompletion(0) - Generate a juniPingTestCompleted notification.

The value of this object defaul…

Bitsr/w

Enumerated Values:

0	testCompletion

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.3

juniAtmVpPingSentProbes

The number of ping probes (OAM cells) that have been sent thus far for
this test. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).

juniAtmVpPingProbeResponses

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.4

The number of ping responses that have been received thus far for this
test. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1).

IF-MIBifIndex ATM-MIBatmVclVpi ATM-MIBatmVclVci ATM-FORUM-SNMP-M4-MIBatmfM4VcTestObject

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.5

juniAtmVpPingStartTime

The time (sysUpTime) when the test started.

SNMPv2-TCTimeStamp

Based On: SNMPv2-SMITimeTicks

Description:

The value of the sysUpTime object at which a specific
occurrence happened. The specific occurrence must be

defined in the description of any object defined using this
type.

If sysUpTime is reset t…

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.6

juniAtmVpPingMinRtt

The shortest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero …

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.7

juniAtmVpPingMaxRtt

The longest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero f…

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.8

juniAtmVpPingAverageRtt

The average round-trip-time (RTT) for all the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VpTestStatus object transitions from notInUse(0) to inUse(1). A
value of ze…

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.2.1.9

juniAtmVcPingTable

table

.1.3.6.1.4.1.4874.2.2.8.1.5.3 · 1 row entry · 9 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVcPingTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVcPingTable'

This table contains entries for extending the ATM-FORUM-SNMP-M4-MIB
atmM4VcTestTable to do ping (multiple loopback) type testing.

juniAtmVcPingEntry row .1.3.6.1.4.1.4874.2.2.8.1.5.3.1

Each entry describes the characteristics, status and results of the
most recent ATM ping test.

Indexes

Column Syntax OID

juniAtmVcPingProbeCount

The number of ping probes (OAM cells) to be sent to complete the test.

probesUnsigned32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.1

juniAtmVcPingTimeOut

Specifies the time-out value, in seconds, for a remote ping operation.

secondsUnsigned32r/w

Constraints:
range: 1-5

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.2

juniAtmVcPingCtlTrapGeneration

The value of this object determines when and if to generate a
notification for this entry:
testCompletion(0) - Generate a juniPingTestCompleted notification.

The value of this object defaults to zero,…

Bitsr/w

Enumerated Values:

0	testCompletion

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.3

juniAtmVcPingSentProbes

The number of ping probes (OAM cells) that have been sent thus far for
this test. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).

juniAtmVcPingProbeResponses

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.4

The number of ping responses that have been received thus far for this
test. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1).

juniAtmSubIfLocationIndex juniAtmSubIfDistinguisher

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.5

juniAtmVcPingStartTime

The time (sysUpTime) when the test started.

SNMPv2-TCTimeStamp

Based On: SNMPv2-SMITimeTicks

Description:

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.6

juniAtmVcPingMinRtt

The shortest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero …

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.7

juniAtmVcPingMaxRtt

The longest round-trip-time (RTT) for the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of zero f…

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.8

juniAtmVcPingAverageRtt

The average round-trip-time (RTT) for all the pings that have received
responses. The value of this object MUST be set to zero when the
atmfM4VcTestStatus object transitions from notInUse(0) to inUse(1). A
value of ze…

millisecondsSNMPv2-SMIUnsigned32

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.5.3.1.9

juniAtmSubIfLocationTable

table

.1.3.6.1.4.1.4874.2.2.8.1.6.2 · 1 row entry · 2 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmSubIfLocationTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmSubIfLocationTable'

The entries in this table report the ifIndex of ATM Subinterfaces by
location.

juniAtmSubIfLocationEntry row .1.3.6.1.4.1.4874.2.2.8.1.6.2.1

A specification of ATM subinterfaces by location.

Indexes

Column	Syntax	OID
juniAtmSubIfLocationIndex The value of a platform interface location.	Juniper-TCJuniInterfaceLocationValue Type Constraints: `range: 1..16`	`.1.3.6.1.4.1.4874.2.2.8.1.6.2.1.1`
juniAtmSubIfLocationIfIndex The ifIndex value of this subinterface.	IF-MIBInterfaceIndex Type Constraints: `range: 1..2147483647` Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	`.1.3.6.1.4.1.4874.2.2.8.1.6.2.1.2`

juniAtmVcClassNameTable

table

.1.3.6.1.4.1.4874.2.2.8.1.7.1 · 1 row entry · 3 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVcClassNameTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVcClassNameTable'

The entries in this table provide mappings of ATM VC class names to
local integer identifiers. These integers are used as indexes into other
MIB tables containing ATM VC attributes associated with the same VC class name.

juniAtmVcClassNameEntry row .1.3.6.1.4.1.4874.2.2.8.1.7.1.1

A mapping of ATM VC class name to an integer identifier for the ATM VC class.

Indexes

juniAtmVcClassName

Column Syntax OID

juniAtmVcClassName

The ATM VC class name uniquely identifying this entry.

OctetString

Constraints:
range: 1-32

.1.3.6.1.4.1.4874.2.2.8.1.7.1.1.1

juniAtmVcClassNameRowStatus

Controls creation/deletion of entries in this table. Only the values
'createAndGo' ,'destroy', 'active' and 'notInService' may be SET.
The SNMP manager would set the row status to notInService before making
any VC c…

Type Values:

1	active
2	notInService
3	notReady
4	createAndGo
5	createAndWait
6	destroy

Description:

.1.3.6.1.4.1.4874.2.2.8.1.7.1.1.2

juniAtmVcClassNameId

The integer identifier associated with this VC class name. The value of
this identifier is assigned by the device when an entry in this table
is created.

Type Constraints:
range: 0..4294967295

.1.3.6.1.4.1.4874.2.2.8.1.7.1.1.3

juniAtmVcClassIdTable

table

.1.3.6.1.4.1.4874.2.2.8.1.7.2 · 1 row entry · 2 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVcClassIdTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVcClassIdTable'

Provides inverse mapping of ATM VC class IDs to ATM VC class names.

juniAtmVcClassIdEntry row .1.3.6.1.4.1.4874.2.2.8.1.7.2.1

A mapping of an integer identifier to an ATM VC class name.

Indexes

juniAtmVcClassIdId

Column	Syntax	OID
juniAtmVcClassIdId The integer identifier associated with this ATM VC class name.	SNMPv2-SMIUnsigned32 Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.4874.2.2.8.1.7.2.1.1`
juniAtmVcClassIdName The ATM VC class name having the associated identifier.	OctetString Constraints: `range: 1-32`	`.1.3.6.1.4.1.4874.2.2.8.1.7.2.1.2`

juniAtmVcClassTable

table

.1.3.6.1.4.1.4874.2.2.8.1.7.3 · 1 row entry · 15 columns

Open in standard view

Uses the junose variant from /opt/observium/mibs/junose.

Command help

Walk juniAtmVcClassTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-UNI-ATM-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-UNI-ATM-MIB::juniAtmVcClassTable'

This table contains Juniper ATM VC Class entries which can be used
to specify the ATM PVC attributes either at creation or modification
time. A row in this table with default values is created when an entry
in juniAtmVcClassNameTable is created.

juniAtmVcClassEntry row .1.3.6.1.4.1.4874.2.2.8.1.7.3.1

Each entry contains the attributes of the ATM VC which would be
applied to the VC either at creation or modification time when this
ATM VC class is associated to it.

Indexes

juniAtmVcClassId

Column Syntax OID

juniAtmVcClassId

The integer identifier associated with this ATM VC class. A value
for this identifier is determined by locating or creating an ATM VC
class name in the juniAtmVcClassNameTable.