Juniper-FRACTIONAL-T1-MIB Table View
Table-centric layout grouping table, row, and column objects.
Tables
1
Rows
1
Columns
7
juniFt1IfTable
table
.1.3.6.1.4.1.4874.2.2.6.1.2
·
1 row entry
·
7 columns
Uses the junose variant from
Command help
/opt/observium/mibs/junose.
Walk juniFt1IfTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'Juniper-FRACTIONAL-T1-MIB' -M '/opt/observium/mibs/junose:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'Juniper-FRACTIONAL-T1-MIB::juniFt1IfTable'
This table contains entries for FT1 interfaces present in the system.
Each entry describes the characteristics of an FT1 interface.
Creating/deleting entries in this table causes corresponding entries for
be created /deleted in ifTable/ifXTable/juniIfTable.
Creating/deleting entries in this table causes corresponding entries for
be created /deleted in ifTable/ifXTable/juniIfTable.
Indexes
| Column | Syntax | OID | ||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
|
The ifIndex of the FT1 interface. When creating entries in this table,
suitable values for this object are determined by reading juniFt1NextIfIndex. |
IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must … |
.1.3.6.1.4.1.4874.2.2.6.1.2.1.1 |
||||||||||||
|
Controls creation/deletion of entries in this table according to the
RowStatus textual convention, constrained to support the following values only: createAndGo destroy To create an entry in this … |
SNMPv2-TCRowStatusr/w Type Values:
Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of … |
.1.3.6.1.4.1.4874.2.2.6.1.2.1.2 |
||||||||||||
|
The ifIndex of a DS1 interface over which this FT1 interface is to be
layered. A value of zero indicates no layering. An implementation may choose to require that a nonzero value be configured at entry creation. |
IF-MIBInterfaceIndexOrZeror/w Type Constraints: range: 0..2147483647Description: This textual convention is an extension of the InterfaceIndex convention. The latter defines a greater than zero value used to identify an interface or interface sub-layer in the managed system. This extension permits… |
.1.3.6.1.4.1.4874.2.2.6.1.2.1.3 |
||||||||||||
|
A bitmap representing the DS0s on the underlying DS1 interface that
have been allocated to this FT1 interface. |
Juniper-TCJuniTimeSlotMapr/w Type Constraints: range: 4 |
.1.3.6.1.4.1.4874.2.2.6.1.2.1.4 |
||||||||||||
|
Data rate per time slot allocated to this FT1 interface.
|
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4874.2.2.6.1.2.1.5 |
||||||||||||
|
juniFt1IfDataPolarityobsolete
Obsolete. Polarity of data transmitted on this FT1 interface.
Inverted data is used for certain line coding configurations to ensure sufficient one's density for timing recovery by the remote end. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4874.2.2.6.1.2.1.6 |
||||||||||||
|
Selects loopback configuration. loop(1) causes received data to be
looped back out the transmitter. |
Enumerationr/w Enumerated Values:
|
.1.3.6.1.4.1.4874.2.2.6.1.2.1.7 |
