ISIS-DRAFT-25-MIB
Monitored by Observium This document describes a management information base for
the IS-IS Routing protocol, as described in ISO 10589,
when it is used to construct routing tables for IP
networks, as described in RFC 1195.
This document is based on a 1994 IETF draft by Chris
Gunner. This version has been modified to include
current syntax, to exclude portions of the protocol that
are not relevant to IP, and to add management support for
current practice.
Copyright (C) The Internet Society (2005). This version
of this MIB module is part of RFC 0DDD; see the RFC
itself for full legal notices.
Observium actively monitors this MIB
Observium uses this MIB in discovery or polling workflows on applicable devices.
Routing
Explore Observium network monitoring
- Source file
ISIS-DRAFT-25-MIB- Last revised
- Identity
isisMIB- Base OID
1.3.6.1.3.37
Imported Objects
| DIFFSERV-MIB | IndexInteger IndexIntegerNextFree |
| IF-MIB | InterfaceIndex |
| INET-ADDRESS-MIB | InetAddress InetAddressPrefixLength InetAddressType |
| SNMP-FRAMEWORK-MIB | SnmpAdminString |
| SNMPv2-CONF | MODULE-COMPLIANCE (no object page) NOTIFICATION-GROUP (no object page) OBJECT-GROUP (no object page) |
| SNMPv2-SMI | Counter32 experimental MODULE-IDENTITY (no object page) NOTIFICATION-TYPE (no object page) OBJECT-TYPE (no object page) Unsigned32 |
| SNMPv2-TC | RowStatus TEXTUAL-CONVENTION (no object page) TimeStamp TruthValue |
Net-SNMP examples using the extreme MIB directory Show commands
These commands use the standard Observium installation path and load the selected MIB variant before the RFC and Net-SNMP directories.
Translate the module identity
/usr/bin/snmptranslate -Pud -Ir -On -m 'ISIS-DRAFT-25-MIB' -M '/opt/observium/mibs/extreme:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'ISIS-DRAFT-25-MIB::isisMIB'
Walk the MIB subtree
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'ISIS-DRAFT-25-MIB' -M '/opt/observium/mibs/extreme:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'ISIS-DRAFT-25-MIB::isisMIB'
Objects (227)
Showing 227 of 227 objects
Object legend
Object type
Icons distinguish tables, entry rows, columns, scalars, and structural nodes.
SNMPv2-TCTruthValue
Syntax
Blue badges identify the value syntax. Connected badges read as defining module and convention.
IF-MIBifIndex
Table index
Green identifies an index object; yellow names its module when the index is defined elsewhere.
r/w
deprecated
obsolete
Access and status
r/w means read-write. Grey labels mark definitions retained for compatibility.
OBS ✓
Observium use
The indicator appears only when Observium directly references that object.
ifOperStatus
.1.3.6.1.2.1…
Names and OIDs
Object names link to their detail pages. Hover or focus a linked name or badge for available definition details.
.1.3.6.1.3.37 |
||
.1.3.6.1.3.37.0 |
||
.1.3.6.1.3.37.1 |
||
.1.3.6.1.3.37.1.1 |
||
.1.3.6.1.3.37.1.1.1 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.1.1.1 |
|
|
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.1.1.10 |
|
bytesIsisUnsigned16TC
|
.1.3.6.1.3.37.1.1.1.11 |
|
|
Bits
|
.1.3.6.1.3.37.1.1.1.12 |
|
.1.3.6.1.3.37.1.1.1.13 |
||
|
|
.1.3.6.1.3.37.1.1.1.2 |
|
|
|
.1.3.6.1.3.37.1.1.1.3 |
|
|
Unsigned32
|
.1.3.6.1.3.37.1.1.1.4 |
|
|
secondsUnsigned32
|
.1.3.6.1.3.37.1.1.1.5 |
|
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.1.1.6 |
|
|
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.1.1.7 |
.1.3.6.1.3.37.1.1.1.8 |
||
.1.3.6.1.3.37.1.1.1.9 |
||
.1.3.6.1.3.37.1.1.2 |
||
.1.3.6.1.3.37.1.1.2.1 |
||
.1.3.6.1.3.37.1.1.2.1.1 |
||
.1.3.6.1.3.37.1.1.2.1.2 |
||
.1.3.6.1.3.37.1.1.3 |
||
.1.3.6.1.3.37.1.1.3.1 |
||
.1.3.6.1.3.37.1.1.3.1.1 |
||
.1.3.6.1.3.37.1.1.4 |
||
.1.3.6.1.3.37.1.1.4.1 |
||
.1.3.6.1.3.37.1.1.4.1.1 |
||
.1.3.6.1.3.37.1.1.4.1.2 |
||
.1.3.6.1.3.37.1.1.4.1.3 |
||
.1.3.6.1.3.37.1.1.4.1.4 |
||
.1.3.6.1.3.37.1.1.4.1.5 |
||
.1.3.6.1.3.37.1.1.4.1.6 |
||
.1.3.6.1.3.37.1.1.5 |
||
.1.3.6.1.3.37.1.1.5.1 |
||
.1.3.6.1.3.37.1.1.5.1.1 |
||
.1.3.6.1.3.37.1.1.5.1.2 |
||
.1.3.6.1.3.37.1.1.5.1.3 |
||
.1.3.6.1.3.37.1.1.5.1.4 |
||
.1.3.6.1.3.37.1.1.6 |
||
.1.3.6.1.3.37.1.1.6.1 |
||
.1.3.6.1.3.37.1.1.6.1.1 |
||
.1.3.6.1.3.37.1.1.6.1.2 |
||
.1.3.6.1.3.37.1.1.6.1.3 |
||
.1.3.6.1.3.37.1.1.6.1.4 |
||
.1.3.6.1.3.37.1.10 |
||
.1.3.6.1.3.37.1.10.1 |
||
.1.3.6.1.3.37.1.10.1.1 |
||
.1.3.6.1.3.37.1.10.1.10 |
||
|
OctetString
|
.1.3.6.1.3.37.1.10.1.11 |
|
|
Enumeration
|
.1.3.6.1.3.37.1.10.1.12 |
|
.1.3.6.1.3.37.1.10.1.13 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.10.1.14 |
|
.1.3.6.1.3.37.1.10.1.15 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.10.1.2 |
|
.1.3.6.1.3.37.1.10.1.3 |
||
.1.3.6.1.3.37.1.10.1.4 |
||
.1.3.6.1.3.37.1.10.1.5 |
||
.1.3.6.1.3.37.1.10.1.6 |
||
.1.3.6.1.3.37.1.10.1.7 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.10.1.8 |
|
.1.3.6.1.3.37.1.10.1.9 |
||
.1.3.6.1.3.37.1.2 |
||
.1.3.6.1.3.37.1.2.1 |
||
.1.3.6.1.3.37.1.2.1.1 |
||
.1.3.6.1.3.37.1.2.1.1.1 |
||
.1.3.6.1.3.37.1.2.1.1.2 |
||
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.2.1.1.3 |
|
.1.3.6.1.3.37.1.2.1.1.4 |
||
.1.3.6.1.3.37.1.2.1.1.5 |
||
|
Seconds until clearing manually set Overload BitSNMPv2-SMIUnsigned32
|
.1.3.6.1.3.37.1.2.1.1.6 |
|
.1.3.6.1.3.37.1.2.1.1.7 |
||
.1.3.6.1.3.37.1.2.1.1.8 |
||
.1.3.6.1.3.37.1.2.1.1.9 |
||
.1.3.6.1.3.37.1.3 |
||
.1.3.6.1.3.37.1.3.1 |
||
.1.3.6.1.3.37.1.3.2 |
||
.1.3.6.1.3.37.1.3.2.1 |
||
.1.3.6.1.3.37.1.3.2.1.1 |
||
.1.3.6.1.3.37.1.3.2.1.10 |
||
.1.3.6.1.3.37.1.3.2.1.11 |
||
.1.3.6.1.3.37.1.3.2.1.12 |
||
.1.3.6.1.3.37.1.3.2.1.13 |
||
.1.3.6.1.3.37.1.3.2.1.14 |
||
|
|
.1.3.6.1.3.37.1.3.2.1.2 |
|
.1.3.6.1.3.37.1.3.2.1.3 |
||
.1.3.6.1.3.37.1.3.2.1.4 |
||
|
|
Enumeration
|
.1.3.6.1.3.37.1.3.2.1.5 |
.1.3.6.1.3.37.1.3.2.1.6 |
||
.1.3.6.1.3.37.1.3.2.1.7 |
||
.1.3.6.1.3.37.1.3.2.1.8 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.3.2.1.9 |
|
.1.3.6.1.3.37.1.4 |
||
.1.3.6.1.3.37.1.4.1 |
||
.1.3.6.1.3.37.1.4.1.1 |
||
.1.3.6.1.3.37.1.4.1.1.1 |
||
|
millisecondsUnsigned32
|
.1.3.6.1.3.37.1.4.1.1.10 |
|
|
millisecondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.4.1.1.11 |
|
|
secondsUnsigned32
|
.1.3.6.1.3.37.1.4.1.1.12 |
|
|
secondsUnsigned32
|
.1.3.6.1.3.37.1.4.1.1.13 |
|
|
secondsUnsigned32
|
.1.3.6.1.3.37.1.4.1.1.14 |
|
.1.3.6.1.3.37.1.4.1.1.2 |
||
.1.3.6.1.3.37.1.4.1.1.3 |
||
.1.3.6.1.3.37.1.4.1.1.4 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.4.1.1.5 |
|
.1.3.6.1.3.37.1.4.1.1.6 |
||
.1.3.6.1.3.37.1.4.1.1.7 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.4.1.1.8 |
|
|
millisecondsUnsigned32
|
.1.3.6.1.3.37.1.4.1.1.9 |
|
.1.3.6.1.3.37.1.5 |
||
.1.3.6.1.3.37.1.5.1 |
||
.1.3.6.1.3.37.1.5.1.1 |
||
.1.3.6.1.3.37.1.5.1.1.1 |
||
|
Number of frames with ID length mismatchesSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.1.1.10 |
|
.1.3.6.1.3.37.1.5.1.1.11 |
||
.1.3.6.1.3.37.1.5.1.1.12 |
||
|
Number of frames with errors that we have receivedSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.1.1.13 |
|
|
Number of corrupted in-memory framesSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.1.1.2 |
|
|
Number of frames with authentication type mismatchesSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.1.1.3 |
|
|
Number of frames with authentication key failuresSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.1.1.4 |
|
.1.3.6.1.3.37.1.5.1.1.5 |
||
.1.3.6.1.3.37.1.5.1.1.6 |
||
.1.3.6.1.3.37.1.5.1.1.7 |
||
.1.3.6.1.3.37.1.5.1.1.8 |
||
.1.3.6.1.3.37.1.5.1.1.9 |
||
.1.3.6.1.3.37.1.5.2 |
||
.1.3.6.1.3.37.1.5.2.1 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.5.2.1.1 |
|
.1.3.6.1.3.37.1.5.2.1.10 |
||
.1.3.6.1.3.37.1.5.2.1.2 |
||
.1.3.6.1.3.37.1.5.2.1.3 |
||
.1.3.6.1.3.37.1.5.2.1.4 |
||
.1.3.6.1.3.37.1.5.2.1.5 |
||
|
Number of frames with ID field length mismatchSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.2.1.6 |
|
.1.3.6.1.3.37.1.5.2.1.7 |
||
.1.3.6.1.3.37.1.5.2.1.8 |
||
.1.3.6.1.3.37.1.5.2.1.9 |
||
.1.3.6.1.3.37.1.5.3 |
||
.1.3.6.1.3.37.1.5.3.1 |
||
.1.3.6.1.3.37.1.5.3.1.1 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.5.3.1.2 |
|
|
Number of IS-IS Hellos frames seen in this direction
at this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.3 |
|
|
Number of ES-IS frames seen in this direction at
this level.SNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.4 |
|
|
Number of ES Hello frames seen in this direction at
this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.5 |
|
|
Number of IS-IS LSP frames seen in this direction at
this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.6 |
|
|
Number of IS-IS CSNP frames seen in this direction at
this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.7 |
|
|
Number of IS-IS PSNP frames seen in this direction at
this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.8 |
|
|
Number of unknown IS-IS frames seen at this levelSNMPv2-SMICounter32
|
.1.3.6.1.3.37.1.5.3.1.9 |
|
.1.3.6.1.3.37.1.6 |
||
.1.3.6.1.3.37.1.6.1 |
||
.1.3.6.1.3.37.1.6.1.1 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.6.1.1.1 |
|
.1.3.6.1.3.37.1.6.1.1.10 |
||
.1.3.6.1.3.37.1.6.1.1.11 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.6.1.1.2 |
|
|
Enumeration
|
.1.3.6.1.3.37.1.6.1.1.3 |
|
.1.3.6.1.3.37.1.6.1.1.4 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.6.1.1.5 |
|
.1.3.6.1.3.37.1.6.1.1.6 |
||
.1.3.6.1.3.37.1.6.1.1.7 |
||
.1.3.6.1.3.37.1.6.1.1.8 |
||
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.6.1.1.9 |
|
.1.3.6.1.3.37.1.6.2 |
||
.1.3.6.1.3.37.1.6.2.1 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.6.2.1.1 |
|
.1.3.6.1.3.37.1.6.2.1.2 |
||
.1.3.6.1.3.37.1.6.3 |
||
.1.3.6.1.3.37.1.6.3.1 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.6.3.1.1 |
|
.1.3.6.1.3.37.1.6.3.1.2 |
||
.1.3.6.1.3.37.1.6.3.1.3 |
||
.1.3.6.1.3.37.1.6.4 |
||
.1.3.6.1.3.37.1.6.4.1 |
||
.1.3.6.1.3.37.1.6.4.1.1 |
||
.1.3.6.1.3.37.1.7 |
||
.1.3.6.1.3.37.1.7.1 |
||
.1.3.6.1.3.37.1.7.1.1 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.7.1.1.1 |
|
|
|
.1.3.6.1.3.37.1.7.1.1.10 |
|
|
|
Enumeration
|
.1.3.6.1.3.37.1.7.1.1.11 |
|
|
.1.3.6.1.3.37.1.7.1.1.2 |
|
|
|
.1.3.6.1.3.37.1.7.1.1.3 |
|
|
|
.1.3.6.1.3.37.1.7.1.1.4 |
|
|
|
Enumeration
|
.1.3.6.1.3.37.1.7.1.1.5 |
|
|
.1.3.6.1.3.37.1.7.1.1.6 |
|
|
|
.1.3.6.1.3.37.1.7.1.1.7 |
|
.1.3.6.1.3.37.1.7.1.1.8 |
||
|
|
.1.3.6.1.3.37.1.7.1.1.9 |
|
.1.3.6.1.3.37.1.8 |
||
.1.3.6.1.3.37.1.8.1 |
||
.1.3.6.1.3.37.1.8.1.1 |
||
.1.3.6.1.3.37.1.8.1.1.1 |
||
|
|
.1.3.6.1.3.37.1.8.1.1.10 |
|
.1.3.6.1.3.37.1.8.1.1.11 |
||
.1.3.6.1.3.37.1.8.1.1.12 |
||
.1.3.6.1.3.37.1.8.1.1.13 |
||
|
Enumeration
|
.1.3.6.1.3.37.1.8.1.1.14 |
|
.1.3.6.1.3.37.1.8.1.1.2 |
||
.1.3.6.1.3.37.1.8.1.1.3 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.8.1.1.4 |
|
.1.3.6.1.3.37.1.8.1.1.5 |
||
|
|
.1.3.6.1.3.37.1.8.1.1.6 |
|
|
|
Enumeration
|
.1.3.6.1.3.37.1.8.1.1.7 |
.1.3.6.1.3.37.1.8.1.1.8 |
||
.1.3.6.1.3.37.1.8.1.1.9 |
||
.1.3.6.1.3.37.1.9 |
||
.1.3.6.1.3.37.1.9.1 |
||
.1.3.6.1.3.37.1.9.1.1 |
||
.1.3.6.1.3.37.1.9.1.1.1 |
||
.1.3.6.1.3.37.1.9.1.1.2 |
||
.1.3.6.1.3.37.1.9.1.1.3 |
||
.1.3.6.1.3.37.1.9.1.1.4 |
||
.1.3.6.1.3.37.1.9.1.1.5 |
||
|
secondsIsisUnsigned16TC
|
.1.3.6.1.3.37.1.9.1.1.6 |
|
.1.3.6.1.3.37.1.9.1.1.7 |
||
.1.3.6.1.3.37.1.9.1.1.8 |
||
.1.3.6.1.3.37.1.9.2 |
||
.1.3.6.1.3.37.1.9.2.1 |
||
|
Unsigned32
|
.1.3.6.1.3.37.1.9.2.1.1 |
|
.1.3.6.1.3.37.1.9.2.1.2 |
||
.1.3.6.1.3.37.1.9.2.1.3 |
||
.1.3.6.1.3.37.1.9.2.1.4 |
||
.1.3.6.1.3.37.1.9.2.1.5 |
||
|
OctetString
|
.1.3.6.1.3.37.1.9.2.1.6 |
|
.1.3.6.1.3.37.2 |
||
.1.3.6.1.3.37.2.1 |
||
.1.3.6.1.3.37.2.2 |
Dependencies (11) 7 direct · 4 transitive Show tree and compile order Hide dependency details
Each imported module is resolved in the importing module's source directory first, then through the normal default-variant rules.
Dependency tree
Dependency-first compile order
- SNMPv2-SMIrfc
- SNMPv2-TCrfc
- DIFFSERV-DSCP-TCrfc
- IANAifType-MIBrfc
- SNMPv2-CONFrfc
- SNMPv2-MIBrfc
- IF-MIBrfc
- INET-ADDRESS-MIBrfc
- INTEGRATED-SERVICES-MIBrfc
- DIFFSERV-MIBrfc
- SNMP-FRAMEWORK-MIBrfc
- ISIS-DRAFT-25-MIBextremeselected
Type Definitions (19)
| Enumeration |
on(1)off(2)Type used in enabling and disabling a row.
|
|
| OctetString |
range: 0range: 7 ID for a circuit.
|
|
| Unsigned32 |
range: 0..63 Display format:
dInteger sub-range for default metric for single hop.
ISO 10589 provides for 4 types of metric. Only the 'default' metric is used in practice. |
|
| Unsigned32 |
Display format:
dFull Metric for IP Routes. Traffic Engineering extensions
provide 32 bit metrics. |
|
| Enumeration |
area(1)domain(2)Identifies a level.
|
|
| Unsigned32 |
range: 0..127 Display format:
dInteger sub-range for IS-IS priority.
|
|
| Unsigned32 |
range: 512..16000 Display format:
dInteger sub range for maximum LSP size.
|
|
| Enumeration |
level1(1)level2(2)level1and2(3)Identifies one or more levels.
|
|
| Enumeration |
off(1)on(2)waiting(3)overloaded(4)States of the IS-IS protocol.
|
|
| OctetString |
range: 8 The 8 byte Link State PDU (LSP) ID,
consisting of the 6 byte SystemID of the originating IS, a one byte PseudoNode ID which is 0 unless the LSP represents the topology of a LAN, and one byte LSP fragment number that are issued in sequence, starting with 0. Non zero PseudoNode IDs need to be unique to the IS, but need not match the IfIndex. |
|
| Enumeration |
narrow(1)wide(2)both(3)Do we use RFC 1195 style metrics or wide metrics?
|
|
| Enumeration |
internal(1)external(2)Is this an Internal or External Metric?
|
|
| OctetString |
range: 0..20 OSI Network Service Address, e.g. NSAP, SNPA, or Network
Entity Title |
|
| OctetString |
range: 0..64 A block to contain the header from a PDU.
|
|
| Enumeration |
iso8473(129)ipV6(142)ip(204)Types of network protocol supported by Integrated IS-IS.
The values for ISO8473 and IP are those registered for these protocols in ISO TR9577. |
|
| OctetString |
range: 6 The ID for an Intermediate System. This should
be unique within a network, and is included in all PDUs originated by an Intermediate System. The protocol does not place any meanings upon the bits, other than using ordering to break ties in electing a Designated IS on a LAN. |
|
| Unsigned32 |
range: 0..65535 Display format:
dAn Unsigned32 further restricted to 16 Bits. Note that
the ASN.1 BER encoding may still require 24 Bits for some values. |
|
| Unsigned32 |
range: 0..255 Display format:
dAn Unsigned32 further restricted to 8 Bits. Note that
the ASN.1 BER encoding may still require 16 Bits for some values. |
|
| Unsigned32 |
range: 0..16777215 Display format:
dWide Metric for IS Neighbors. ISO 10589 provides a
6 bit metric. Traffic Engineering extensions provide 24 bit metrics. |
Conformance Groups (9)
Compliance Statements (3)
OID
.1.3.6.1.3.37.2.1.1The compliance statement for agents that support
the IS-IS MIB.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2,
but for which there are compliance requirements.
Those requirements, and similar requirements for
related objects, are expressed below in
pseudo-OBJECT clause form in this description:
-- OBJECT isisSummAddressType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4 Summary
-- Addresses, and anticipates the support of
-- IPv6 addresses.
--
--
-- OBJECT isisRedistributeAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4
-- Redistribution Addresses, and anticipates
-- the support of IPv6 addresses.
the IS-IS MIB.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2,
but for which there are compliance requirements.
Those requirements, and similar requirements for
related objects, are expressed below in
pseudo-OBJECT clause form in this description:
-- OBJECT isisSummAddressType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4 Summary
-- Addresses, and anticipates the support of
-- IPv6 addresses.
--
--
-- OBJECT isisRedistributeAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4
-- Redistribution Addresses, and anticipates
-- the support of IPv6 addresses.
Required groups
| mandatory | isisSystemGroup | |
| mandatory | isisCircuitGroup | |
| mandatory | isisISAdjGroup | |
| mandatory | isisNotificationObjectGroup | |
| mandatory | isisNotificationGroup |
OID
.1.3.6.1.3.37.2.1.2The compliance statement for agents that fully
support the IS-IS MIB.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2,
but for which there are compliance requirements.
Those requirements, and similar requirements for
related objects, are expressed below in
pseudo-OBJECT clause form in this description:
-- OBJECT isisSummAddressType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4 Summary
-- Addresses, and anticipates the support of
-- IPv6 addresses.
--
--
-- OBJECT isisRedistributeAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4
-- Redistribution Addresses, and anticipates
-- the support of IPv6 addresses.
support the IS-IS MIB.
There are a number of INDEX objects that cannot be
represented in the form of OBJECT clauses in SMIv2,
but for which there are compliance requirements.
Those requirements, and similar requirements for
related objects, are expressed below in
pseudo-OBJECT clause form in this description:
-- OBJECT isisSummAddressType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4 Summary
-- Addresses, and anticipates the support of
-- IPv6 addresses.
--
--
-- OBJECT isisRedistributeAddrType
-- SYNTAX InetAddressType { ipv4(1), ipv6(2) }
--
-- DESCRIPTION
-- The MIB requires support for IPv4
-- Redistribution Addresses, and anticipates
-- the support of IPv6 addresses.
Required groups
| mandatory | isisSystemGroup | |
| mandatory | isisCircuitGroup | |
| mandatory | isisISAdjGroup | |
| mandatory | isisNotificationObjectGroup | |
| mandatory | isisNotificationGroup | |
| mandatory | isisISPDUCounterGroup | |
| mandatory | isisRATableGroup | |
| mandatory | isisISIPRADestGroup | |
| mandatory | isisLSPGroup |
OID
.1.3.6.1.3.37.2.1.3When this MIB is implemented without support for
read-create (i.e. in read-only mode), the implementation
can claim read-only compliance. Such a device can then
be monitored but can not be configured with this MIB.
read-create (i.e. in read-only mode), the implementation
can claim read-only compliance. Such a device can then
be monitored but can not be configured with this MIB.
Required groups
| mandatory | isisSystemGroup | |
| mandatory | isisCircuitGroup | |
| mandatory | isisISAdjGroup |
Object refinements
| Object | Access | Syntax | Description |
|---|---|---|---|
| isisSysLevelType | readonly | Write access is not required. | |
| isisSysID | readonly | Write access is not required. | |
| isisSysMaxPathSplits | readonly | Write access is not required. | |
| isisSysMaxLSPGenInt | readonly | Write access is not required. | |
| isisSysPollESHelloRate | readonly | Write access is not required. | |
| isisSysWaitTime | readonly | Write access is not required. | |
| isisSysAdminState | readonly | Write access is not required. | |
| isisSysL2toL1Leaking | readonly | Write access is not required. | |
| isisSysMaxAge | readonly | Write access is not required. | |
| isisManAreaAddrExistState | readonly | Write access is not required. | |
| isisSysLevelOrigLSPBuffSize | readonly | Write access is not required. | |
| isisSysLevelMinLSPGenInt | readonly | Write access is not required. | |
| isisSysLevelSetOverload | readonly | Write access is not required. | |
| isisSysLevelSetOverloadUntil | readonly | Write access is not required. | |
| isisSysLevelMetricStyle | readonly | Write access is not required. | |
| isisSysLevelSPFConsiders | readonly | Write access is not required. | |
| isisSysLevelTEEnabled | readonly | Write access is not required. | |
| isisSysReceiveLSPBufferSize | readonly | Write access is not required. | |
| isisSummAddrExistState | readonly | Write access is not required. | |
| isisSummAddrMetric | readonly | Write access is not required. | |
| isisSummAddrFullMetric | readonly | Write access is not required. | |
| isisRedistributeAddrExistState | readonly | Write access is not required. | |
| isisCircAdminState | readonly | Write access is not required. | |
| isisCircExistState | readonly | Write access is not required. | |
| isisCircType | readonly | Write access is not required. | |
| isisCircExtDomain | readonly | Write access is not required. | |
| isisCircLevelType | readonly | Write access is not required. | |
| isisCircPassiveCircuit | readonly | Write access is not required. | |
| isisCircMeshGroupEnabled | readonly | Write access is not required. | |
| isisCircMeshGroup | readonly | Write access is not required. | |
| isisCircSmallHellos | readonly | Write access is not required. | |
| isisCircExtendedCircID | readonly | Write access is not required. | |
| isisCircIfIndex | readonly | Write access is not required. | |
| isisCirc3WayEnabled | readonly | Write access is not required. | |
| isisCircLevelMetric | readonly | Write access is not required. | |
| isisCircLevelWideMetric | readonly | Write access is not required. | |
| isisCircLevelISPriority | readonly | Write access is not required. | |
| isisCircLevelHelloMultiplier | readonly | Write access is not required. | |
| isisCircLevelHelloTimer | readonly | Write access is not required. | |
| isisCircLevelDRHelloTimer | readonly | Write access is not required. | |
| isisCircLevelLSPThrottle | readonly | Write access is not required. | |
| isisCircLevelMinLSPRetransInt | readonly | Write access is not required. | |
| isisCircLevelCSNPInterval | readonly | Write access is not required. | |
| isisCircLevelPartSNPInterval | readonly | Write access is not required. |
Notifications / Traps (18)
| Name | OID | Description |
|---|---|---|
.1.3.6.1.3.37.0.1 |
This notification is generated when the system
enters or leaves the Overload state. The number of times this has be generated and cleared is kept track of by isisSysStatLSPDbaseOloads. |
|
.1.3.6.1.3.37.0.10 |
A notification sent when we receive a PDU
with incorrect authentication information field. This notification includes the header of the packet, which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisAuthenticationFailure notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.11 |
A notification sent when we receive a Hello
PDU from an IS running a different version of the protocol. This notification includes the header of the packet, which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisVersionSkew notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.12 |
A notification sent when we receive a Hello
PDU from an IS which does not share any area address. This notification includes the header of the packet, which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisAreaMismatch notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.13 |
A notification sent when we receive a Hello
PDU from an IS, but do not establish an adjacency for some reason. The agent must throttle the generation of consecutive isisRejectedAdjacency notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.14 |
A notification sent when we attempt to propagate
an LSP which is larger than the dataLinkBlockSize for the circuit. The agent must throttle the generation of consecutive isisLSPTooLargeToPropagate notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.15 |
A notification sent when a Level 1 LSP or Level
2 LSP is received which is larger than the local value for isisSysLevelOrigLSPBuffSize, or when an LSP is received containing the supported Buffer Size option and the value in the PDU option field does not match the local value for isisSysLevelOrigLSPBuffSize. We pass up the size from the option field and the size of the LSP when one of them exceeds our configuration. The agent must throttle the generation of consecutive isisOrigLSPBuffSizeMismatch notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.16 |
A notification sent when a non-pseudonode
segment 0 LSP is received that has no matching protocols supported. This may be because the system does not generate the field, or because there are no common elements. The list of protocols supported should be included in the notification: it may be empty if the TLV is not supported, or if the TLV is empty. The agent must throttle the generation of consecutive isisProtocolsSupportedMismatch notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.17 |
A notification sent when an adjacency changes
state, entering or leaving state up. The first 6 bytes of the isisPduLspId are the SystemID of the adjacent IS. The isisAdjState is the new state of the adjacency. |
|
.1.3.6.1.3.37.0.18 |
This notification is generated when we receive
an LSP with a parse error. The isisCircIfIndex holds in index of the circuit on which the PDU arrived. The isisPduFragment holds start of the LSP, and the isisErrorOffset points to the problem. If the problem is a malformed TLV, isisErrorOffset points to start of the TLV and isisErrorTLVType holds the value of the type. If the problem is with the LSP header, isisErrorOffset points to the suspicious byte. The number of such LSPs is accumulated in isisSysStatLSPErrors. |
|
.1.3.6.1.3.37.0.2 |
This notification is generated when one of the
manual areaAddresses assigned to this system is ignored when computing routes. The object isisNotificationAreaAddress describes the area that has been dropped. The number of times this event has been generated is counted by isisSysStatManAddrDropFromAreas. The agent must throttle the generation of consecutive isisManualAddressDrops notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.3 |
This notification is generated when we find that
an LSP that was stored in memory has become corrupted. The number of times this has been generated is counted by isisSysCorrLSPs. We forward an LSP ID. We may have independent knowledge of the ID, but in some implementations there is a chance that the ID itself will be corrupted. |
|
.1.3.6.1.3.37.0.4 |
When the sequence number on an LSP we generate
wraps the 32 bit sequence counter, we purge and wait to re-announce this information. This notification describes that event. Since these should not be generated rapidly, we generate an event each time this happens. While the first 6 bytes of the LSPID are ours, the other two contain useful information. |
|
.1.3.6.1.3.37.0.5 |
A notification sent when we receive a PDU
with a different value of the System ID Length. This notification includes the an index to identify the circuit where we saw the PDU and the header of the PDU which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisIDLenMismatch notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.6 |
A notification sent when we receive a PDU
with a different value of the Maximum Area Addresses. This notification includes the header of the packet, which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisMaxAreaAddressesMismatch notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |
|
.1.3.6.1.3.37.0.7 |
A notification sent when we receive a PDU
with our systemID and zero age. This notification includes the circuit Index and router ID from the LSP, if available, which may help a network manager identify the source of the confusion. |
|
.1.3.6.1.3.37.0.8 |
When we receive an LSP with our System ID
and different contents, we may need to reissue the LSP with a higher sequence number. We send this notification if we need to increase the sequence number by more than one. If two Intermediate Systems are configured with the same System ID, this notification will fire. |
|
.1.3.6.1.3.37.0.9 |
A notification sent when we receive a PDU
with the wrong authentication type field. This notification includes the header of the packet, which may help a network manager identify the source of the confusion. The agent must throttle the generation of consecutive isisAuthenticationTypeFailure notifications so that there is at least a 5-second gap between notifications of this type. When notifications are throttled, they are dropped, not queued for sending at a future time. |