HUAWEI-NTP-MIB Table View

This is a bit indicating that the association was created
from configuration information and should not be demobilized
if the peer becomes unreachable.

This is a bit indicating that system support authentication.

This is a bit indicating that message pass authentication which is authentic.

The IP address of the peer. When creating a new
association, a value for this object should be set
before the row is made active.

The UDP port number on which the peer receives NTP messages.

The IP address of the local host. Multi-homing can
be supported using this object.

The UDP port number on which the local host receives NTP messages.

This is a two-bit code warning of an impending leap
second to be inserted in the NTP timescale. The bits
are set before 23:59 on the day of insertion and reset
after 00:00 on the following day. This causes the
number …

This is an integer indicating the association mode,
with values coded as follows,
0, unspecified
1, symmetric active - A host operating in this mode
sends periodic messages regardless of the
reach abilit…

This is a integer indicating the stratum level
of the peer clock, with values defined as follows:
0, unspecified
1, primary reference (e.g.,, radio clock)
2-255, secondary reference (via NTP)

The interval at which the peer polls the local host.

The interval at which the local host polls the peer.

This is a signed integer indicating the precision of
the peer clock, in seconds to the nearest power of two.
The value must be rounded to the next larger power of
two; for instance, a 50-Hz (20 ms) or 60-Hz (16.67 ms)
p…

This is a signed fixed-point number indicating
the total roundtrip delay to the primary reference source
at the root of the synchronization subnet, in milliseconds.
Note that this variable can take on both positive and …

This is a signed fixed-point number indicating
the maximum error of the peer clock relative to
the primary reference source at the root of the
synchronization subnet, in milliseconds. Only
positive values greater than …

The reference identifier of the peer.
This is a 32-bit code identifying the particular reference clock.
In the case of stratum 0 (unspecified) or stratum 1 (primary
reference source), this is a four-octet, left-justifie…

This is the local time at the peer, in timestamp format,
when the local clock was last updated. If the local clock has
never been synchronized, the value is zero.

This is the local time, in timestamp format,
at the peer when it's latest NTP message was sent.
If the peer becomes unreachable the value is set to zero

This is the local time, in timestamp format,
when the latest NTP message from the peer arrived.
If the peer becomes unreachable the value is set to zero.

This is the local time, in timestamp format,
at which the NTP message departed the sender.

This is a shift register of NTP.WINDOW bits used to
determine the reach ability status of the peer,
with bits entering from the least significant (rightmost) end.
A peer is considered reachable if at least
one bit in th…

This is an integer counter indicating the valid samples
remaining in the filter register. It is used to
determine the reach ability state and when the
poll interval should be increased or decreased.

This is an integer counter used to control the
interval of transmitted NTP messages from the local host to the peer.

This is a signed fixed-point number indicating
the roundtrip delay of the peer clock relative to
the local clock over the network path between them,
in milliseconds. Note that this variable can take on
both positive an…

This is a signed, fixed-point number indicating the offset
of the peer clock relative to the local clock, in milliseconds.

This is an indicating that peer of sample Variance

This is a signed fixed-point number indicating the
maximum error of the peer clock relative to the local
clock over the network path between them, in milliseconds.
Only positive values greater than zero are possible.

This is an unsigned integer identifying the cryptographic
key used to generate the message-authentication code.

Round-trip delay of the peer clock relative to the
local clock over the network path between them, in
milliseconds. This variable can take on both positive
and negative values, depending on clock precision
and skew-err…

The offset of the peer clock relative to the local clock in milliseconds.

The maximum error of the peer clock relative to the
local clock over the network path between them, in
milliseconds. Only positive values greater than zero
are possible.

This is an integer indicating the association mode,
with values coded as follows,
0, unspecified
1, symmetric active - A host operating in this mode
sends periodic messages regardless of the
reach abilit…

The number of received messages.

The number of send messages.

The information about the message.

The status object for this row. When a management
station is creating a new row, it should set the
value for cntpPeersPeerAddress at least, before the
row can be made 'active'.