H3C-SNA-DLSW-EXT-MIB Table View

This table defines the peer transport connections
that will be initiated or accepted by this DLSw.
          
This table augments dlswTConnConfigTable.

h3cdeTConnConfigEntry row .1.3.6.1.4.1.2011.10.2.62.1.2.1.1

A list of objects that define specific configuration for
a DLSw peer transport connection.

Indexes

No indexes recorded

Column	Syntax	OID
h3cdeTConnConfigVersion This value identifies which version (first octet) and release (second octet) of the DLSw standard is supported by this partner DLSw. This information is obtained from a DLSw Capabilities Exchange message received from t…	OctetStringr/w Constraints: range: 2-2	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.1
h3cdeTConnConfigPriority The priority for remote peer.	Integer32r/w Constraints: range: 1-5	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.2
h3cdeTConnConfigLfSize The largest frame size.	DLSW-MIBLFSizer/w Type Values: 516 lfs516 635 lfs635 754 lfs754 873 lfs873 993 lfs993 1112 lfs1112 1231 lfs1231 1350 lfs1350 1470 lfs1470 1542 lfs1542 1615 lfs1615 1688 lfs1688 1761 lfs1761 1833 lfs1833 1906 lfs1906 1979 lfs1979 2052 lfs2052 2345 lfs2345 2638 lfs2638 2932 lfs2932 3225 lfs3225 3518 lfs3518 3812 lfs3812 4105 lfs4105 4399 lfs4399 4865 lfs4865 5331 lfs5331 5798 lfs5798 6264 lfs6264 6730 lfs6730 7197 lfs7197 7663 lfs7663 8130 lfs8130 8539 lfs8539 8949 lfs8949 9358 lfs9358 9768 lfs9768 10178 lfs10178 10587 lfs10587 10997 lfs10997 11407 lfs11407 12199 lfs12199 12992 lfs12992 13785 lfs13785 14578 lfs14578 15370 lfs15370 16163 lfs16163 16956 lfs16956 17749 lfs17749 20730 lfs20730 23711 lfs23711 26693 lfs26693 29674 lfs29674 32655 lfs32655 38618 lfs38618 41600 lfs41600 44591 lfs44591 47583 lfs47583 50575 lfs50575 53567 lfs53567 56559 lfs56559 59551 lfs59551 65535 lfs65535	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.3
h3cdeTConnConfigKeepaliveIntval The keepalive interval value.	secondsInteger32r/w Constraints: range: 1-1200	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.4
h3cdeTConnConfigBackup The current remote peer is configured as the backup of another configured remote peer.	Enumerationr/w Enumerated Values: 1 yes 2 no	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.5
h3cdeTConnConfigBackupTAddr It is the ip address of a configured remote peer of which the current remote peer is configrued as backup.	DLSW-MIBTAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.6
h3cdeTConnConfigBackupLinger Backup peer linger.	minutesInteger32r/w Constraints: range: 0-1440	.1.3.6.1.4.1.2011.10.2.62.1.2.1.1.7

A list of peer transport connections.
Each connected peer will create a conceptual row in the table.
When the peer disconnects, the row will be deleted from the table.
          
This table augments dlswTConnOperTable.

h3cdeTConnOperEntry row .1.3.6.1.4.1.2011.10.2.62.1.2.2.1

A list of objects that contain spefific operational
information for a DLSw peer transport connection.

Indexes

No indexes recorded

Column	Syntax	OID
h3cdeTConnOperPeerType The current remote peer is configured when the value is 'configured'.	Enumeration Enumerated Values: 1 configured 2 learningDynamic 3 other	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.1
h3cdeTConnOperVendorID The value identifies the manufacturer's IEEE-assigned Organizationally Unique Identifier (OUI) of remote peer.	OctetString	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.2
h3cdeTConnOperVersionString Version information of remote peer. The length up to 512 bytes.	OctetString	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.3
h3cdeTConnOperUpTime The amount of time (in seconds) since this transport connection last entered the 'connected' state.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.4
h3cdeTConnOperMulticastAddress When remote peer supports DLSw2.0, this node identifies its multicast address.	DLSW-MIBTAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.5
h3cdeTConnOperStCapTcpNumber Number of tcp supported when capabilities exchanging.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.6
h3cdeTConnOperRecvPkts The number of Switch-to-Switch Protocol (SSP) messages received on this tcp transport connection.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.7
h3cdeTConnOperSendPkts The number of SSP messages sent on this tcp transport connection.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.8
h3cdeTConnOperDropPkts The number of SSP messages dropped on this tcp transport connection.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.62.1.2.2.1.9

This table defines the TCP transport connections that
will be either initiated by or accepted by this DSLw.
It augments the entries in dlswTConnConfigTable whose
domain is dlswTCPDomain. In other words for each conceptual row
in the dlswTConnConfigTable, if the dlswTConnConfigTDomain is
dlswTCPDomain, that conceptual row will be augmented by this
table.
          
dlswTCPDomain, dlswTConnConfigTable, and dlswTConnConfigTDomain
are all imported from DLSW-MIB (RFC 2024).
          
This table augments dlswTConnTcpConfigTable.

h3cdeTConnTcpConfigEntry row .1.3.6.1.4.1.2011.10.2.62.1.2.3.1

A list of objects that define specific configuration for
a DLSw peer transport connection within the dlswTCPDomain.
dlswTCPDomain is imported from DLSW-MIB (RFC 2024).

Indexes

No indexes recorded

Column	Syntax	OID
h3cdeTConnTcpConfigQueueMax Maximum output TCP queue size for this remote peer. For DLSw over TCP encapsulation, packets may be queued due to congestion of the TCP network. This variable is used to set the output queue maximum of the underlying TC…	Integer32r/w Constraints: range: 50-2000	.1.3.6.1.4.1.2011.10.2.62.1.2.3.1.1

A list of bridge group which is serving for DLSw.

h3cdeBridgeEntry row .1.3.6.1.4.1.2011.10.2.62.1.3.1.1

A list of bridge information.

Indexes

h3cdeBridgeNumIndex

Column	Syntax	OID
h3cdeBridgeNumIndex This value identifies the bridge number.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.2011.10.2.62.1.3.1.1.1
h3cdeBridgeRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.3.1.1.2

The list of interface on which DLSw is active.

h3cdeBridgeIfEntry row .1.3.6.1.4.1.2011.10.2.62.1.3.2.1

The list of bridge interface information.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
h3cdeBridgeIfBrgGrp This value identifies the bridge number attached to the interface.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.2011.10.2.62.1.3.2.1.1
h3cdeBridgeIfRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.3.2.1.2

The table defines attributes related for those
QLLC that participate in data link switching.

h3cdeQllcEntry row .1.3.6.1.4.1.2011.10.2.62.1.4.1.1

The ifIndex belongs to the interface which link protocol is x.25.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
h3cQllcX121Address X.121 address.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.1
h3cQllcLocalMac The virtual MAC address used to represent the QLLC-attached link station to the rest of the DLSw network.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.2
h3cQllcLocalSap The SAP used to represent this link station.	OctetStringr/w Constraints: range: 1-1	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.3
h3cQllcRemoteMac The MAC address to which DLSw should attempt to connect this link station. If this information is not available, a length of zero for this object should be returned.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.4
h3cQllcRemoteSap The SAP of the remote station to which this link station should be connected. If this information is not available, a length of zero for this object should be returned.	OctetStringr/w Constraints: range: 0-1	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.5
h3cQllcRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.4.1.1.6

The table defines parameters for the interfaces
whose link protocol is SDLC.

h3cdeSdlcPortEntry row .1.3.6.1.4.1.2011.10.2.62.1.5.1.1

Sdlc port entry.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
h3cdeSdlcPortRole The SDLC role of interface.	Enumerationr/w Enumerated Values: 1 primary 2 seconday 3 norole	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.1
h3cdeSdlcPortSendWindow Size of local send window.	Integer32r/w Constraints: range: 1-7	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.2
h3cdeSdlcPortModulo Size of modulus.	Enumerationr/w Enumerated Values: 8 m8 128 m128	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.3
h3cdeSdlcPortMaxPdu Maximum bytes for incoming frames.	Integer32r/w Constraints: range: 1-17600	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.4
h3cdeSdlcPortMaxSendQueue Size of hold queue.	Integer32r/w Constraints: range: 20-255	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.5
h3cdeSdlcPortMaxTransmission Number of times to retry an operation.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.6
h3cdeSdlcPortSimultaneousEnable Activate SDLC two-way simultaneous mode.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.7
h3cdeSdlcPortTimerACK Time to wait for a reply to a frame.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.8
h3cdeSdlcPortTimerLifeTime Time to wait for a reply used by secondary station.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.9
h3cdeSdlcPortTimerPollPause Time between polls for each secondary SDLC station.	millisecondsInteger32r/w Constraints: range: 1-10000	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.10
h3cdeSdlcPortRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.5.1.1.11

This table defines parameters for the Ethernet interface.

h3cdeLlc2PortEntry row .1.3.6.1.4.1.2011.10.2.62.1.6.1.1

LLC2 port entry.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
h3cdeLlc2PortMaxAck Maximum of I-frames received before ACK.	Integer32r/w Constraints: range: 1-127	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.1
h3cdeLlc2PortMaxPdu Maximum of LLC2 pdu length.	Integer32r/w Constraints: range: 1-1700	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.2
h3cdeLlc2PortMaxSendQueue Queue for sending llc2 I-frames.	Integer32r/w Constraints: range: 20-200	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.3
h3cdeLlc2PortMaxTransmission Retry times of operations.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.4
h3cdeLlc2PortModulo Modulus of LLC2.	Enumerationr/w Enumerated Values: 8 m8 128 m128	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.5
h3cdeLlc2PortReceiveWindow Maximum number of I-frames to send before received ACK.	Integer32r/w Constraints: range: 1-127	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.6
h3cdeLlc2PortTimerAck Waiting for ACK time after sending an I-frame.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.7
h3cdeLlc2PortTimerAckDelay Maximum time allows I-frames incoming without replay ACK.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.8
h3cdeLlc2PortTimerDetect Detect the link status.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.9
h3cdeLlc2PortTimerBusy Waiting time while other LLC2 station is in busy state.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.10
h3cdeLlc2PortTimerPoll Waiting time after a P frame is sent.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.11
h3cdeLlc2PortTimerReject Waiting time after a REJ frame is sent.	millisecondsInteger32r/w Constraints: range: 1-60000	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.12
h3cdeLlc2PortRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.6.1.1.13

Reachable cache table.

h3cdeRchCacheEntry row .1.3.6.1.4.1.2011.10.2.62.1.7.3.1

Reachable cache entry.

Indexes

h3cdeRchCacheIndex

Column	Syntax	OID
h3cdeRchCacheIndex Index of reachable cache entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.1
h3cdeRchCacheStatus Current status of reachable cache entry.	Enumeration Enumerated Values: 1 found 2 verify 3 noCacheInfo 4 exploring 5 waiting	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.2
h3cdeRchCacheRemainTime Remain time of reachable cache entry.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.3
h3cdeRchCacheMac MAC address of reachable cache entry.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.4
h3cdeRchCacheRemoteIpAddrType Remote peer ip address type.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.5
h3cdeRchCacheRemoteIp Remote peer ip address of reachable cache entry.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.6
h3cdeRchCacheRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.7.3.1.7

Information of interface which works for DLSw Ethernet redundancy.

h3cdeEBIfEntry row .1.3.6.1.4.1.2011.10.2.62.1.8.3.1

Parameters defined for DLSw Ethernet redundancy interface.

Indexes

RFC1213-MIBifIndex

Column	Syntax	OID
h3cdeEBMulticastMac Multicast MAC address configured for the Ethernet redundancy of dlsw module. When Ethernet redundancy is inactive, its value is '000000000000'H. To active Ethernet redundancy, give it a valid multicast MAC address.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.8.3.1.1
h3cdeEBPriority Priority configured for the Ethernet redundancy of DLSw module.	Integer32r/w Constraints: range: 1-254	.1.3.6.1.4.1.2011.10.2.62.1.8.3.1.2
h3cdeEBtimer Timer for the Ethernet redundancy of DLSw module.	Integer32r/w Constraints: range: 100-5000	.1.3.6.1.4.1.2011.10.2.62.1.8.3.1.3
h3cdeEBRowStatus RowStatus.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.8.3.1.4

MAC address mapping table.

h3cdeEBMacMapEntry row .1.3.6.1.4.1.2011.10.2.62.1.8.4.1

MAC address mapping entry.

Indexes

RFC1213-MIBifIndex h3cdeEBMacMapIndex

Column	Syntax	OID
h3cdeEBMacMapIndex Index of MAC address mapping entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.62.1.8.4.1.1
h3cdeEBMacMapLocalMac Local MAC address in MAC address mapping. When creating a new conceptual row, h3cdeEBMacMapLocalMac and h3cdeEBMacMapRemoteMac should be set simultaneously.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.8.4.1.2
h3cdeEBMacMapRemoteMac Remote MAC address of MAC address mapping. When creating a new conceptual row, h3cdeEBMacMapLocalMac and h3cdeEBMacMapRemoteMac should be set simultaneously.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.8.4.1.3
h3cdeEBMacMapNeighbour Neighbour of MAC address mapping.	DLSW-MIBMacAddressNCr/w Type Constraints: range: 0 range: 6	.1.3.6.1.4.1.2011.10.2.62.1.8.4.1.4
h3cdeEBMacMapRowStatus Status of MAC address mapping entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.62.1.8.4.1.5