H3C-DOT11-RRM-MIB Table View

Configure WLAN RRM based radio type.
When 802.11b parameter is modified, 802.11g parameter will be
changed at the same time.
In the same way, when 802.11g parameter is modified, 802.11b parameter
will be changed at the same time.

h3cDot11RRMRadioCfgEntry row .1.3.6.1.4.1.2011.10.2.75.8.1.2.1

Configure WLAN RRM based radio type.
When 802.11b parameter is modified, 802.11g parameter will be
changed at the same time.
In the same way, when 802.11g parameter is modified, 802.11b parameter
will be changed at the …

Indexes

h3cDot11RRMRadioType

Column	Syntax	OID
h3cDot11RRMRadioType 802.11 radio type.	H3C-DOT11-REF-MIBH3cDot11RadioType Type Values: 1 dot11a 2 dot11b 4 dot11g 8 dot11n 16 dot11gn 32 dot11an 64 dot11ac 128 dot11gac	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.1
h3cDot11RRMCfgChlState Enable/Disable dynamic channel selection.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.2
h3cDot11RRMCfgChlMode Configure the mode of channel selection. This node can be configured only when dynamic channel selection is enabled.	Enumerationr/w Enumerated Values: 1 selfDecisive 2 userTriggered	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.3
h3cDot11RRMChlProntoRadioElmt Specify the AP and radio that will change channel at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of channel selection control is user-trigger…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.4
h3cDot11RRMCfgPwrState Enable/Disable dynamic power selection for the band.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.5
h3cDot11RRMCfgPwrMode Configure the mode of transmit power control. This node can be configured only when dynamic power selection is enabled.	Enumerationr/w Enumerated Values: 1 selfDecisive 2 userTriggered	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.6
h3cDot11RRMPwrProntoRadioElmt Specify the AP and radio that will change power at next calibration cycle. 0 is returned when getting the value of this node. This node can be configured only when the mode of transmit power control is user-triggered. W…	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.7
h3cDot11RRMCfgIntrvl Configure the calibration interval.	minuteSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.8
h3cDot11RRMCfgIntrfThres Configure the interface threshold. By default, interference observed on an operating channel is considered during dynamic frequency selection and transmit power control. If the interference percentage on the channel re…	percentInteger32r/w Constraints: range: 1-100	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.9
h3cDot11RRMCfgNoiseThres Configure the noise threshold.	Integer32r/w Constraints: range: -127-127	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.10
h3cDot11RRMCfgPERThres Configure the CRC error threshold. If the percentage of CRC errors reaches the threshold, RRM will perform resource adjustment to control the situation.	percentInteger32r/w Constraints: range: 1-100	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.11
h3cDot11RRMCfgToleranceFctr Configure the tolerance level. During dynamic frequency selection (DFS), the channel will be changed only if there is a better channel having lesser interference and packet error rate than those specified by the user.	percentInteger32r/w Constraints: range: 1-45	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.12
h3cDot11RRMCfgAdjacencyFctr Configure the adjacency factor for the band. If transmit power control (TPC) is configured, power will be adjusted when the nth neighbor is detected. The value n is the adjacency factor.	Integer32r/w Constraints: range: 1-16	.1.3.6.1.4.1.2011.10.2.75.8.1.2.1.13

This table defines the RRM parameters for AP.

h3cDot11RRMAPCfgEntry row .1.3.6.1.4.1.2011.10.2.75.8.1.3.1

Each entry contains information of RRM parameters for AP.

Indexes

H3C-DOT11-REF-MIBh3cDot11APElementIndex

Column	Syntax	OID
h3cDot11RRMAPWorkMode AP work mode.	Enumerationr/w Enumerated Values: 1 normal 2 monitor 3 hybrid	.1.3.6.1.4.1.2011.10.2.75.8.1.3.1.1

This table defines RRM self-decisive radio group.

h3cDot11RRMSDRadioGroupEntry row .1.3.6.1.4.1.2011.10.2.75.8.1.4.1

Each entry contains information of one RRM self-decisive radio group.

Indexes

h3cDot11RRMSDRadioGroupId

Column	Syntax	OID
h3cDot11RRMSDRadioGroupId Represents RRM self-decisive radio group ID.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.75.8.1.4.1.1
h3cDot11RRMSDRadioGroupDesc Represents the description of RRM self-decisive radio group.	OctetStringr/w	.1.3.6.1.4.1.2011.10.2.75.8.1.4.1.2
h3cDot11RRMSDRdGrpChlHolddownTm Represents the channel holddown time of RRM self-decisive radio group.	minuteSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.75.8.1.4.1.3
h3cDot11RRMSDRdGrpPwrHolddownTm Represents the power holddown time of RRM self-decisive radio group.	minuteSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.2011.10.2.75.8.1.4.1.4
h3cDot11RRMSDRdGroupRowStatus The row status of this table entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.2011.10.2.75.8.1.4.1.5

This table defines the RRM parameters for AP.

h3cDot11RRMAPCfg2Entry row .1.3.6.1.4.1.2011.10.2.75.8.1.5.1

Each entry contains information of RRM parameters for AP.

Indexes

h3cDot11RRMAPSerialID

Column	Syntax	OID
h3cDot11RRMAPSerialID Serial ID of the AP.	H3C-DOT11-REF-MIBH3cDot11ObjectIDType Type Constraints: range: 0..127	.1.3.6.1.4.1.2011.10.2.75.8.1.5.1.1
h3cDot11RRMAPIntfThreshold Represents threshold of AP interference . If the number of AP interference exceeds this threshold, AP interference trap will be sent.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.1.5.1.2
h3cDot11RRMStaIntfThreshold Represents threshold of STA interference. If the number of STA interference exceeds this threshold, station interference trap will be sent.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.1.5.1.3
h3cDot11RRMCoChlIntfTrapThhd Represents threshold of interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.	dbmSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.1.5.1.4
h3cDot11RRMAdjChlIntfTrapThhd Represents threshold of adjacent interference trap with current ap. If signal strength of the device exceeds this threshold, corresponding trap will be sent.	dbmSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.1.5.1.5

This table shows the RRM channel information of each radio
on all APs.

h3cDot11RRMChlRptEntry row .1.3.6.1.4.1.2011.10.2.75.8.2.1.1

Each entry contains information of RRM channel information
of the radio on the AP.

Indexes

h3cDot11RRMRadioIndex h3cDot11RRMChlRptChlNum

Column	Syntax	OID
h3cDot11RRMRadioIndex Represents index of the radio.	H3C-DOT11-REF-MIBH3cDot11RadioElementIndex	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.1
h3cDot11RRMChlRptChlNum Channel number.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.2
h3cDot11RRMChlRptChlType Channel type.	Enumeration Enumerated Values: 1 primeChannel 2 offChannel	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.3
h3cDot11RRMChlRptChlQlty Channel quality.	Enumeration Enumerated Values: 1 good 2 bad	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.4
h3cDot11RRMChlRptNbrCnt Number of neighbors found on the channel.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.5
h3cDot11RRMChlRptLoad Load observed on the channel in percentage.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.6
h3cDot11RRMChlRptUtlz Utilization of the channel in percentage.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.7
h3cDot11RRMChlRptIntrf Interference observed on the channel in percentage.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.8
h3cDot11RRMChlRptPER Packet error rate observed on the channel in percentage.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.9
h3cDot11RRMChlRptRetryRate Percentage of retransmission happened on the channel.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.10
h3cDot11RRMChlRptNoise Noise observed on the channel.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.11
h3cDot11RRMChlRptRadarIndtcr Radar detection status.	Enumerationr/w Enumerated Values: 1 detected 2 notDetected	.1.3.6.1.4.1.2011.10.2.75.8.2.1.1.12

This table shows the RRM neighbor information of each radio
on all APs.

h3cDot11RRMNbrInfoEntry row .1.3.6.1.4.1.2011.10.2.75.8.2.2.1

Each entry contains information of RRM neighbor information
of the radio on an AP.

Indexes

h3cDot11RRMRadioIndex h3cDot11RrmNbrBSSID

Column	Syntax	OID
h3cDot11RrmNbrBSSID MAC address of the AP.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.1
h3cDot11RrmNbrChl Channel number on which the neighbor was found.	H3C-DOT11-REF-MIBH3cDot11ChannelScopeType	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.2
h3cDot11RRMNbrIntrf Interference observed on the channel in percentage by neighbor.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.3
h3cDot11RrmNbrRSSI Signal strength of the AP in dBm.	dBmSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.4
h3cDot11RrmNbrType Type of the AP, managed or unmanaged.	Enumeration Enumerated Values: 1 managed 2 unmanaged	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.5
h3cDot11RrmNbrSSID SSID of the Neighbor.	H3C-DOT11-REF-MIBH3cDot11SSIDStringType	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.6
h3cDot11RrmNbrSNR Signal to noise ratio of the AP in dB.	dBSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.7
h3cDot11RrmNbrNF Noise floor of the AP in dBm.	dBmSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.2.1.8

This table shows the details of the latest three channel changes
and power changes applied on all APs, including time of change,
reason of the change and the channel, power, interference parameters.

h3cDot11RRMHistoryEntry row .1.3.6.1.4.1.2011.10.2.75.8.2.3.1

Each entry shows the details of channel and power changes.

Indexes

h3cDot11RRMRadioIndex h3cDot11RRMHistoryId h3cDot11RRMHistoryRecIndctr

Column	Syntax	OID
h3cDot11RRMHistoryId History number of the change.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.1
h3cDot11RRMHistoryRecIndctr History record type of the change.	Enumeration Enumerated Values: 1 before 2 after	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.2
h3cDot11RRMHistoryChl Channel on which the radio operates before/after the change of channel or power.	H3C-DOT11-REF-MIBH3cDot11ChannelScopeType	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.3
h3cDot11RRMHistoryPwr Power of the radio before/after the change of channel or power.	dBmSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.4
h3cDot11RRMHistoryLoad Load observed on the radio in percentage before/after the change of channel or power.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.5
h3cDot11RRMHistoryUtlz Utilization of the radio in percentage before/after the change of channel or power.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.6
h3cDot11RRMHistoryIntrf Interference observed on the radio in percentage before/after the change of channel or power.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.7
h3cDot11RRMHistoryNoise Noise observed on the radio before/after the change of channel or power.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.8
h3cDot11RRMHistoryPER Packet error rate observed on the radio in percentage before/after the change of channel or power.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.9
h3cDot11RRMHistoryRetryRate Percentage of retransmission happened on the radio before/after the change of channel or power.	percentInteger32 Constraints: range: 0-100	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.10
h3cDot11RRMHistoryChgReason Reason for the change of channel or power. The various bit positions are: |0 |Others | |1 |Coverage | |2 |Radar | |3 |Retransmission …	Bits Enumerated Values: 0 others 1 coverage 2 radar 3 retransmission 4 packetsDiscarded 5 interference	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.11
h3cDot11RRMHistoryChgDateTime The time when the channel or power change occurred.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.10.2.75.8.2.3.1.12

This table shows the RRM neighbor information of each radio
on all APs.

h3cDot11RRMRadioNbrInfoEntry row .1.3.6.1.4.1.2011.10.2.75.8.2.4.1

Each entry contains information of RRM neighbor information
of the radio on an AP.

Indexes

h3cDot11RRMRadioNbrAPID h3cDot11RRMRadioNbrRadioID

Column	Syntax	OID
h3cDot11RRMRadioNbrAPID AP serial id.	H3C-DOT11-REF-MIBH3cDot11ObjectIDType Type Constraints: range: 0..127	.1.3.6.1.4.1.2011.10.2.75.8.2.4.1.1
h3cDot11RRMRadioNbrRadioID Radio Id on AP.	H3C-DOT11-REF-MIBH3cDot11RadioScopeType	.1.3.6.1.4.1.2011.10.2.75.8.2.4.1.2
h3cDot11RRMRadioNbrSSID All neighbour SSIDs scanned by the selected radio.	OctetString	.1.3.6.1.4.1.2011.10.2.75.8.2.4.1.3

This table shows the devices of AP detected

h3cDot11MonitorDetectedDevEntry row .1.3.6.1.4.1.2011.10.2.75.8.4.1.1

Each entry contains information of detected devices.

Indexes

h3cDot11MonitorDevMAC H3C-DOT11-REF-MIBh3cDot11APElementIndex

Column	Syntax	OID
h3cDot11MonitorDevMAC Represents MAC address of the device detected.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.1
h3cDot11MonitorDevType Represents type of the device detected.	Enumeration Enumerated Values: 1 client 2 ap 3 adhoc 4 wirelessBridge 5 unknown	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.2
h3cDot11MonitorDevVendor Represents vendor of the detected device.	OctetString	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.3
h3cDot11MonitorDevSSID Represents the service set identifier for the ESS of the device which type is ap or adhoc.	OctetString	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.4
h3cDot11MonitorDevBSSID Represents the basic service set identifier of the detected device.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.5
h3cDot11MonitorDevChannel Represents the channel in which the device was last detected. AP will choose the channel which has maximum signal strength as effective channel, as there is interference between adjacent channels.	H3C-DOT11-REF-MIBH3cDot11ChannelScopeType	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.6
h3cDot11MonitorRadioId Represents the radio ID of the AP that detected the device.	H3C-DOT11-REF-MIBH3cDot11RadioScopeType	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.7
h3cDot11MonitorDevMaxRSSI Represents the maximum detected RSSI of the device in a scan report cycle.	dbmSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.8
h3cDot11MonitorDevBeaconIntvl Represents the beacon interval for the detected device(not include the device which type is client).	millisecondSNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.9
h3cDot11MonitorDevFstDctTime Represents the time at which the device was first detected.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.10
h3cDot11MonitorDevLstDctTime Represents the time at which the device was detected last time.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.11
h3cDot11MonitorDevClear This object is used to clear the information of the device detected in the WLAN. It will return false for get operation.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.12
h3cDot11MonitorDevSNR Represents the SNR of the device in a scan report cycle.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.2011.10.2.75.8.4.1.1.13