EtherLike-MIB
Monitored by Observium The MIB module to describe generic objects for
ethernet-like network interfaces.
The following reference is used throughout this
MIB module:
[IEEE 802.3 Std] refers to:
IEEE Std 802.3, 2002 Edition: 'IEEE Standard
for Information technology -
Telecommunications and information exchange
between systems - Local and metropolitan
area networks - Specific requirements -
Part 3: Carrier sense multiple access with
collision detection (CSMA/CD) access method
and physical layer specifications', as
amended by IEEE Std 802.3ae-2002:
'Amendment: Media Access Control (MAC)
Parameters, Physical Layer, and Management
Parameters for 10 Gb/s Operation', August,
2002.
Of particular interest is Clause 30, '10 Mb/s,
100 Mb/s, 1000 Mb/s, and 10 Gb/s Management'.
Copyright (C) The Internet Society (2003). This
version of this MIB module is part of RFC 3635;
see the RFC itself for full legal notices.
Observium actively monitors this MIB
Observium uses this MIB in discovery or polling workflows on applicable devices.
Discovery
Ports
Explore Observium network monitoring
- Source file
EtherLike-MIB- Last revised
- Identity
etherMIB- Base OID
1.3.6.1.2.1.35
Imported Objects
| IF-MIB | ifIndex InterfaceIndex |
| SNMPv2-CONF | MODULE-COMPLIANCE (no object page) OBJECT-GROUP (no object page) |
| SNMPv2-SMI | Counter32 Counter64 Integer32 mib-2 MODULE-IDENTITY (no object page) OBJECT-IDENTITY (no object page) OBJECT-TYPE (no object page) transmission |
| SNMPv2-TC | TruthValue |
Net-SNMP examples using the rfc MIB directory Show commands
These commands use the standard Observium installation path and load the selected MIB variant before the RFC and Net-SNMP directories.
Translate the module identity
/usr/bin/snmptranslate -Pud -Ir -On -m 'EtherLike-MIB' -M '/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'EtherLike-MIB::etherMIB'
Walk the MIB subtree
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'EtherLike-MIB' -M '/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'EtherLike-MIB::etherMIB'
Objects (57)
2 directly used by Observium
Showing 57 of 57 objects
Object legend
Object type
Icons distinguish tables, entry rows, columns, scalars, and structural nodes.
SNMPv2-TCTruthValue
Syntax
Blue badges identify the value syntax. Connected badges read as defining module and convention.
IF-MIBifIndex
Table index
Green identifies an index object; yellow names its module when the index is defined elsewhere.
r/w
deprecated
obsolete
Access and status
r/w means read-write. Grey labels mark definitions retained for compatibility.
OBS ✓
Observium use
The indicator appears only when Observium directly references that object.
ifOperStatus
.1.3.6.1.2.1…
Names and OIDs
Object names link to their detail pages. Hover or focus a linked name or badge for available definition details.
.1.3.6.1.2.1.10.7 |
||
.1.3.6.1.2.1.10.7.10 |
||
.1.3.6.1.2.1.10.7.10.1 |
||
|
Enumeration
|
.1.3.6.1.2.1.10.7.10.1.1 |
|
|
Enumeration
|
.1.3.6.1.2.1.10.7.10.1.2 |
|
.1.3.6.1.2.1.10.7.10.1.3 |
||
.1.3.6.1.2.1.10.7.10.1.4 |
||
.1.3.6.1.2.1.10.7.10.1.5 |
||
.1.3.6.1.2.1.10.7.10.1.6 |
||
.1.3.6.1.2.1.10.7.11 |
||
.1.3.6.1.2.1.10.7.11.1 |
||
.1.3.6.1.2.1.10.7.11.1.1 |
||
.1.3.6.1.2.1.10.7.11.1.2 |
||
.1.3.6.1.2.1.10.7.11.1.3 |
||
.1.3.6.1.2.1.10.7.11.1.4 |
||
.1.3.6.1.2.1.10.7.11.1.5 |
||
.1.3.6.1.2.1.10.7.11.1.6 |
||
.1.3.6.1.2.1.10.7.2 |
||
|
|
.1.3.6.1.2.1.10.7.2.1 |
|
.1.3.6.1.2.1.10.7.2.1.1 |
||
.1.3.6.1.2.1.10.7.2.1.10 |
||
.1.3.6.1.2.1.10.7.2.1.11 |
||
.1.3.6.1.2.1.10.7.2.1.13 |
||
.1.3.6.1.2.1.10.7.2.1.16 |
||
|
|
ObjectIdentifier
|
.1.3.6.1.2.1.10.7.2.1.17 |
.1.3.6.1.2.1.10.7.2.1.18 |
||
|
|
Enumeration
|
.1.3.6.1.2.1.10.7.2.1.19 |
.1.3.6.1.2.1.10.7.2.1.2 |
||
.1.3.6.1.2.1.10.7.2.1.20 |
||
|
Enumeration
|
.1.3.6.1.2.1.10.7.2.1.21 |
|
.1.3.6.1.2.1.10.7.2.1.3 |
||
.1.3.6.1.2.1.10.7.2.1.4 |
||
.1.3.6.1.2.1.10.7.2.1.5 |
||
.1.3.6.1.2.1.10.7.2.1.6 |
||
.1.3.6.1.2.1.10.7.2.1.7 |
||
.1.3.6.1.2.1.10.7.2.1.8 |
||
.1.3.6.1.2.1.10.7.2.1.9 |
||
.1.3.6.1.2.1.10.7.5 |
||
.1.3.6.1.2.1.10.7.5.1 |
||
|
Integer32
|
.1.3.6.1.2.1.10.7.5.1.2 |
|
.1.3.6.1.2.1.10.7.5.1.3 |
||
.1.3.6.1.2.1.10.7.6 |
||
|
|
.1.3.6.1.2.1.10.7.6.1 |
|
|
|
.1.3.6.1.2.1.10.7.6.2 |
|
.1.3.6.1.2.1.10.7.7 |
||
|
|
.1.3.6.1.2.1.10.7.7.1 |
|
|
|
.1.3.6.1.2.1.10.7.7.2 |
|
.1.3.6.1.2.1.10.7.9 |
||
.1.3.6.1.2.1.10.7.9.1 |
||
|
Bits
|
.1.3.6.1.2.1.10.7.9.1.1 |
|
.1.3.6.1.2.1.10.7.9.1.2 |
||
.1.3.6.1.2.1.10.7.9.1.3 |
||
.1.3.6.1.2.1.35 |
||
.1.3.6.1.2.1.35.1 |
||
.1.3.6.1.2.1.35.2 |
||
.1.3.6.1.2.1.35.2.1 |
||
.1.3.6.1.2.1.35.2.2 |
Dependencies (6) 4 direct · 2 transitive Show tree and compile order Hide dependency details
Each imported module is resolved in the importing module's source directory first, then through the normal default-variant rules.
Dependency tree
Dependency-first compile order
- SNMPv2-SMIrfc
- SNMPv2-TCrfc
- IANAifType-MIBrfc
- SNMPv2-CONFrfc
- SNMPv2-MIBrfc
- IF-MIBrfc
- EtherLike-MIBrfcselected
Conformance Groups (15)
|
etherStatsGroup
deprecated
|
dot3StatsIndex dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsSingleCollisionFrames dot3StatsMultipleCollisionFrames dot3StatsSQETestErrors dot3StatsDeferredTransmissions dot3StatsLateCollisions dot3StatsExcessiveCollisions dot3StatsInternalMacTransmitErrors dot3StatsCarrierSenseErrors dot3StatsFrameTooLongs dot3StatsInternalMacReceiveErrors dot3StatsEtherChipSet
********* THIS GROUP IS DEPRECATED **********
A collection of objects providing information applicable to all ethernet-like network interfaces. This object group has been deprecated and replaced by etherStatsBaseGroup and etherStatsLowSpeedGroup. |
.1.3.6.1.2.1.35.2.1.1
|
|
A collection of objects providing a histogram
of packets successfully transmitted after experiencing exactly N collisions. |
.1.3.6.1.2.1.35.2.1.2
|
|
|
etherStats100MbsGroup
deprecated
|
dot3StatsIndex dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsSingleCollisionFrames dot3StatsMultipleCollisionFrames dot3StatsDeferredTransmissions dot3StatsLateCollisions dot3StatsExcessiveCollisions dot3StatsInternalMacTransmitErrors dot3StatsCarrierSenseErrors dot3StatsFrameTooLongs dot3StatsInternalMacReceiveErrors dot3StatsEtherChipSet dot3StatsSymbolErrors
********* THIS GROUP IS DEPRECATED **********
A collection of objects providing information applicable to 100 Mb/sec ethernet-like network interfaces. This object group has been deprecated and replaced by etherStatsBaseGroup and etherStatsHighSpeedGroup. |
.1.3.6.1.2.1.35.2.1.3
|
|
etherStatsBaseGroup
deprecated
|
dot3StatsIndex dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsSingleCollisionFrames dot3StatsMultipleCollisionFrames dot3StatsDeferredTransmissions dot3StatsLateCollisions dot3StatsExcessiveCollisions dot3StatsInternalMacTransmitErrors dot3StatsCarrierSenseErrors dot3StatsFrameTooLongs dot3StatsInternalMacReceiveErrors
********* THIS GROUP IS DEPRECATED **********
A collection of objects providing information applicable to all ethernet-like network interfaces. This object group has been deprecated and replaced by etherStatsBaseGroup2 and etherStatsHalfDuplexGroup, to separate objects which must be implemented by all ethernet-like network interfaces from objects that need only be implemented on ethernet-like network interfaces that are capable of half-duplex operation. |
.1.3.6.1.2.1.35.2.1.4
|
|
A collection of objects providing information
applicable to ethernet-like network interfaces capable of operating at 10 Mb/s or slower in half-duplex mode. |
.1.3.6.1.2.1.35.2.1.5
|
|
|
A collection of objects providing information
applicable to ethernet-like network interfaces capable of operating at 100 Mb/s or faster. |
.1.3.6.1.2.1.35.2.1.6
|
|
|
A collection of objects providing information
about the duplex mode of an ethernet-like network interface. |
.1.3.6.1.2.1.35.2.1.7
|
|
|
A collection of objects providing information
about the MAC Control sublayer on ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.8
|
|
|
A collection of objects providing information
about and control of the MAC Control PAUSE function on ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.9
|
|
|
dot3StatsIndex dot3StatsAlignmentErrors dot3StatsFCSErrors dot3StatsInternalMacTransmitErrors dot3StatsFrameTooLongs dot3StatsInternalMacReceiveErrors
A collection of objects providing information
applicable to all ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.10
|
|
|
dot3StatsSingleCollisionFrames dot3StatsMultipleCollisionFrames dot3StatsDeferredTransmissions dot3StatsLateCollisions dot3StatsExcessiveCollisions dot3StatsCarrierSenseErrors
A collection of objects providing information
applicable only to half-duplex ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.11
|
|
|
dot3HCStatsAlignmentErrors dot3HCStatsFCSErrors dot3HCStatsInternalMacTransmitErrors dot3HCStatsFrameTooLongs dot3HCStatsInternalMacReceiveErrors dot3HCStatsSymbolErrors
A collection of objects providing high-capacity
statistics applicable to higher-speed ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.12
|
|
|
A collection of objects providing high-capacity
statistics for the MAC Control sublayer on higher-speed ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.13
|
|
|
A collection of objects providing high-capacity
statistics for the MAC Control PAUSE function on higher-speed ethernet-like network interfaces. |
.1.3.6.1.2.1.35.2.1.14
|
|
|
A collection of objects providing information
about the Rate Control function on ethernet-like interfaces. |
.1.3.6.1.2.1.35.2.1.15
|
Compliance Statements (4)
OID
.1.3.6.1.2.1.35.2.2.1******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance.
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance.
Required groups
| mandatory | etherStatsGroup | |
| optional | etherCollisionTableGroup |
This group is optional. It is appropriate for all systems which have the necessary metering. Implementation in such systems is highly recommended. |
OID
.1.3.6.1.2.1.35.2.2.2******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have 100 Mb/sec ethernet-like
network interfaces.
This compliance is deprecated and replaced by
dot3Compliance.
The compliance statement for managed network
entities which have 100 Mb/sec ethernet-like
network interfaces.
This compliance is deprecated and replaced by
dot3Compliance.
Required groups
| mandatory | etherStats100MbsGroup | |
| optional | etherCollisionTableGroup |
This group is optional. It is appropriate for all systems which have the necessary metering. Implementation in such systems is highly recommended. |
OID
.1.3.6.1.2.1.35.2.2.3******** THIS COMPLIANCE IS DEPRECATED ********
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance2.
The compliance statement for managed network
entities which have ethernet-like network
interfaces.
This compliance is deprecated and replaced by
dot3Compliance2.
Required groups
| mandatory | etherStatsBaseGroup | |
| optional | etherDuplexGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating in full-duplex mode. It is highly recommended for all ethernet-like network interfaces. |
| optional | etherStatsLowSpeedGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at 10 Mb/s or slower in half-duplex mode. |
| optional | etherStatsHighSpeedGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at 100 Mb/s or faster. |
| optional | etherControlGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control sublayer. |
| optional | etherControlPauseGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control PAUSE function. |
| optional | etherCollisionTableGroup |
This group is optional. It is appropriate for all ethernet-like network interfaces which are capable of operating in half-duplex mode and have the necessary metering. Implementation in systems with such interfaces is highly recommended. |
OID
.1.3.6.1.2.1.35.2.2.4The compliance statement for managed network
entities which have ethernet-like network
interfaces.
Note that compliance with this MIB module
requires compliance with the ifCompliance3
MODULE-COMPLIANCE statement of the IF-MIB
(RFC2863). In addition, compliance with this
MIB module requires compliance with the
mauModIfCompl3 MODULE-COMPLIANCE statement of
the MAU-MIB (RFC3636).
entities which have ethernet-like network
interfaces.
Note that compliance with this MIB module
requires compliance with the ifCompliance3
MODULE-COMPLIANCE statement of the IF-MIB
(RFC2863). In addition, compliance with this
MIB module requires compliance with the
mauModIfCompl3 MODULE-COMPLIANCE statement of
the MAU-MIB (RFC3636).
Required groups
| mandatory | etherStatsBaseGroup2 | |
| optional | etherDuplexGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating in full-duplex mode. It is highly recommended for all ethernet-like network interfaces. |
| optional | etherRateControlGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at speeds faster than 1000 Mb/s. It is highly recommended for all ethernet-like network interfaces. |
| optional | etherStatsLowSpeedGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at 10 Mb/s or slower in half-duplex mode. |
| optional | etherStatsHighSpeedGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at 100 Mb/s or faster. |
| optional | etherStatsHalfDuplexGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating in half-duplex mode. |
| optional | etherHCStatsGroup |
This group is mandatory for all ethernet-like network interfaces which are capable of operating at 10 Gb/s or faster. It is recommended for all ethernet-like network interfaces which are capable of operating at 1000 Mb/s or faster. |
| optional | etherControlGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control sublayer. |
| optional | etherHCControlGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control sublayer and are capable of operating at 10 Gb/s or faster. |
| optional | etherControlPauseGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control PAUSE function. |
| optional | etherHCControlPauseGroup |
This group is mandatory for all ethernet-like network interfaces that support the MAC Control PAUSE function and are capable of operating at 10 Gb/s or faster. |
| optional | etherCollisionTableGroup |
This group is optional. It is appropriate for all ethernet-like network interfaces which are capable of operating in half-duplex mode and have the necessary metering. Implementation in systems with such interfaces is highly recommended. |