ES4650F-MIB Table View

Table of descriptive and status information about
the switch units in this system.

switchInfoEntry row .1.3.6.1.4.1.259.8.1.9.1.1.3.1

Table providing descriptions and status information for
switch units.

Indexes

swUnitIndex

Column	Syntax	OID
swUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.1
swHardwareVer Hardware version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.2
swMicrocodeVer Microcode version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.3
swLoaderVer Loader version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.4
swBootRomVer Boot ROM code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.5
swOpCodeVer Operation code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.6
swPortNumber The number of ports on this switch.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.7
swPowerStatus Indicates the switch using internalPower(1), redundantPower(2) or both(3)	Enumeration Enumerated Values: 1 internalPower 2 redundantPower 3 internalAndRedundantPower	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.8
swRoleInSystem Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.	Enumeration Enumerated Values: 1 master 2 backupMaster 3 slave	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.9
swSerialNumber Serial number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.10
swExpansionSlot1 Type of expansion module in this switch slot 1.	Enumeration Enumerated Values: 1 notPresent 2 other 3 hundredBaseFxScMmf 4 hundredBaseFxScSmf 5 hundredBaseFxMtrjMmf 6 thousandBaseSxScMmf 7 thousandBaseSxMtrjMmf 8 thousandBaseXGbic 9 thousandBaseLxScSmf 10 thousandBaseT 11 stackingModule 12 thousandBaseSfp 13 tenHundredBaseT4port 14 tenHundredBaseFxMtrj4port 15 comboStackingSfp 16 tenHundredBaseT 17 comboThousandBaseTxSfp 18 eightPortSfpModule 19 tenGigaPortModule	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.11
swExpansionSlot2 Type of expansion module in this switch slot 2.	Enumeration Enumerated Values: 1 notPresent 2 other 3 hundredBaseFxScMmf 4 hundredBaseFxScSmf 5 hundredBaseFxMtrjMmf 6 thousandBaseSxScMmf 7 thousandBaseSxMtrjMmf 8 thousandBaseXGbic 9 thousandBaseLxScSmf 10 thousandBaseT 11 stackingModule 12 thousandBaseSfp 13 tenHundredBaseT4port 14 tenHundredBaseFxMtrj4port 15 comboStackingSfp 16 tenHundredBaseT 17 comboThousandBaseTxSfp 18 eightPortSfpModule 19 tenGigaPortModule	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.12
swServiceTag Service tag serial-number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.13
swModelNumber Model number of the switch.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.14
swEpldVer The EPLD version of the switch.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.15
swExpectedModuleOpCodeVer The module opcode version reside in the switch, note that this variable represent the desired version of the module which might plug in. For version validation, only the swExpectedModuleOpCodeVer of the master is used. …	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.8.1.9.1.1.3.1.16

Table about the status of individual powers.

switchIndivPowerEntry row .1.3.6.1.4.1.259.8.1.9.1.1.6.1

Table about the status of individual power.

Indexes

swIndivPowerUnitIndex swIndivPowerIndex

Column	Syntax	OID
swIndivPowerUnitIndex This is defined as swUnitIndex.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.6.1.1
swIndivPowerIndex 1 means internal power, 2 means external power.	Enumeration Enumerated Values: 1 internalPower 2 externalPower	.1.3.6.1.4.1.259.8.1.9.1.1.6.1.2
swIndivPowerStatus notPresent(1) means not present, green(2) means up, red(3) means down.	Enumeration Enumerated Values: 1 notPresent 2 green 3 red	.1.3.6.1.4.1.259.8.1.9.1.1.6.1.3

The fan status table.

switchFanEntry row .1.3.6.1.4.1.259.8.1.9.1.1.9.1

A conceptual row of the switchFanTable.

Indexes

switchUnitIndex switchFanIndex

Column	Syntax	OID
switchUnitIndex The unit of the switch for the stackable device.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.1
switchFanIndex The unit number of the fan.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.2
switchFanStatus Indicating the status of the fan, 1:ok; 2:failure.	Enumeration Enumerated Values: 1 ok 2 failure	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.3
switchFanAdminSpeed The speed of the fan, measured in rpm (rotations per minute). Set this object to 0 to enter auto mode, set to other values to enter manual mode.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.4
switchFanFailureCount The total failure count of the fan since the switch has reboot.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.5
switchFanOperSpeed The operational value of the fan speed, measured in rpm (rotations per minute).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.9.1.6

The table which collects temperature infomration of the
switch.

switchThermalTempEntry row .1.3.6.1.4.1.259.8.1.9.1.1.11.1

A conceptual row of the switchThermalTempTable.

Indexes

switchThermalTempUnitIndex switchThermalTempThermalIndex

Column	Syntax	OID
switchThermalTempUnitIndex The unit of the switch for stackable device.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.11.1.1
switchThermalTempThermalIndex The thermal index of the switch.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.11.1.2
switchThermalTempValue The temperature value in the device in grade Celsius.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.11.1.3

The table for configuring the thermal action.

switchThermalActionEntry row .1.3.6.1.4.1.259.8.1.9.1.1.12.1

A conceptual row of the switchThermalActionTable.

Indexes

switchThermalActionUnitIndex switchThermalActionThermalIndex switchThermalActionIndex

Column	Syntax	OID
switchThermalActionUnitIndex The unit of the switch for stackable device.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.1
switchThermalActionThermalIndex The thermal index of the switch.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.2
switchThermalActionIndex The action index of the switchTheramlActionTable.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.3
switchThermalActionRisingThreshold The rising threshold of the switch temperature.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.4
switchThermalActionFallingThreshold The falling threshold of the switch temperature.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.5
switchThermalActionAction The action that will be taken when the temperature exceeds the rising threshold or falls below the falling threshold.	Bitsr/w Enumerated Values: 0 trap	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.6
switchThermalActionStatus Set valid(1) to create an entry, Set Invalid(2) to delete an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.1.12.1.7

Table of descriptive and status information about
the switch modules in this system.

switchModuleInfoEntry row .1.3.6.1.4.1.259.8.1.9.1.1.13.1

Table providing descriptions and status information for
switch modules.

Indexes

swModuleUnitIndex swModuleModuleIndex

Column	Syntax	OID
swModuleUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.1
swModuleModuleIndex This object identifies the module within the switch for which this entry contains information.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.2
swModuleHardwareVer Hardware version of the module board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.3
swModuleMicrocodeVer Microcode version of the module board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.4
swModuleLoaderVer Loader version of the module board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.5
swModuleBootRomVer Boot ROM code version of the module board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.6
swModuleOpCodeVer Operation code version of the module board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.7
swModulePortNumber The number of ports of this module.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.8
swModuleSerialNumber Serial number of the module.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.9
swModuleType Type of module.	Enumeration Enumerated Values: 1 notPresent 2 other 3 hundredBaseFxScMmf 4 hundredBaseFxScSmf 5 hundredBaseFxMtrjMmf 6 thousandBaseSxScMmf 7 thousandBaseSxMtrjMmf 8 thousandBaseXGbic 9 thousandBaseLxScSmf 10 thousandBaseT 11 stackingModule 12 thousandBaseSfp 13 tenHundredBaseT4port 14 tenHundredBaseFxMtrj4port 15 comboStackingSfp 16 tenHundredBaseT 17 comboThousandBaseTxSfp 18 eightPortSfpModule 19 tenGigaPortModule	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.10
swModuleModelNumber Model number of the module.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.11
swModuleEpldVer The EPLD version of the module.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.12
swModuleDescr A textual description of the entity to describe the module.	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.259.8.1.9.1.1.13.1.13

Table of descriptive and status information describing
the configuration of each switch port. This table also
contains information about each trunk.

portEntry row .1.3.6.1.4.1.259.8.1.9.1.2.1.1

An entry in the table, describing the configuration of
one switch port or trunk.

Indexes

portIndex

Column	Syntax	OID
portIndex The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.1
portName The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.2
portType Indicates the port type of the configuration of the switch.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseSfp 9 hundredBaseFxScSingleMode 10 hundredBaseFxScMultiMode 11 thousandBaseCX 12 tenG 13 tenGBaseT 14 hundredBaseBX 15 thousandBaseBX	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.3
portSpeedDpxCfg Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode…	Enumerationr/w Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 5 tx 6 rx	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.5
portCapabilities Port or trunk capabilities.	Bitsr/w Enumerated Values: 0 portCap10half 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 portCap10gHalf 7 portCap10gFull 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.6
portAutonegotiation Whether auto-negotiation is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case t…	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.8
portFlowCtrlStatus (2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently confi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.9
portTrunkIndex The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding tru…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.10
portComboForcedMode This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal…	Enumerationr/w Enumerated Values: 1 none 2 copperForced 3 copperPreferredAuto 4 sfpForced 5 sfpPreferredAuto	.1.3.6.1.4.1.259.8.1.9.1.2.1.1.12

Table describing the configuration and status of each
trunk.

trunkEntry row .1.3.6.1.4.1.259.8.1.9.1.3.3.1

An entry describing the configuration and status of a
particular trunk.

Indexes

trunkIndex

Column	Syntax	OID
trunkIndex Identifies the trunk within the switch that is described by the table entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.3.3.1.1
trunkPorts The complete set of ports currently associated with this trunk.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.9.1.3.3.1.2
trunkCreation A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.	Enumeration Enumerated Values: 1 static 2 lacp	.1.3.6.1.4.1.259.8.1.9.1.3.3.1.3
trunkStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.3.3.1.4

Table for LACP port configuration.

lacpPortEntry row .1.3.6.1.4.1.259.8.1.9.1.4.1.1

Entry for LACP port configuration. While an entry may
exist for a particular port, the port may not support
LACP and an attempt to enable LACP may result in
failure.

Indexes

lacpPortIndex

Column	Syntax	OID
lacpPortIndex The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.4.1.1.1
lacpPortStatus Whether 802.3ad LACP is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.4.1.1.2

The table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType.

staPortEntry row .1.3.6.1.4.1.259.8.1.9.1.5.2.1

The conceptual entry of staPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
staPortFastForward Whether fast forwarding is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.2
staPortProtocolMigration When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.3
staPortAdminEdgePort The administrative value of the edge port parameter. A value of true(1) indicates that this port should be assumed as an edge-port and a value of false(2) indicates that this port should be assumed as a non-edge-port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.4
staPortOperEdgePort The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.5
staPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.6
staPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-de…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.7
staPortSystemStatus Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.9
staPortLongAdminPathCost The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This obje…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.10
staPortLongOperPathCost The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This objec…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.11
staPortAdminEdgePortWithAuto The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-po…	Enumerationr/w Enumerated Values: 1 true 2 false 3 auto	.1.3.6.1.4.1.259.8.1.9.1.5.2.1.17

This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0.

xstInstanceCfgEntry row .1.3.6.1.4.1.259.8.1.9.1.5.6.4.1

A conceptual row containing the property of the RST or MST instance.

Indexes

xstInstanceCfgIndex

Column	Syntax	OID
xstInstanceCfgIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.1
xstInstanceCfgPriority The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.2
xstInstanceCfgTimeSinceTopologyChange The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.3
xstInstanceCfgTopChanges The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.4
xstInstanceCfgDesignatedRoot The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identi…	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.5
xstInstanceCfgRootCost The cost of the path to the root as seen from this bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.6
xstInstanceCfgRootPort The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.7
xstInstanceCfgMaxAge The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is t…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.8
xstInstanceCfgHelloTime The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.9
xstInstanceCfgHoldTime This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.10
xstInstanceCfgForwardDelay For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the por…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.11
xstInstanceCfgBridgeMaxAge For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the va…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.12
xstInstanceCfgBridgeHelloTime For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.13
xstInstanceCfgBridgeForwardDelay For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.14
xstInstanceCfgTxHoldCount For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.15
xstInstanceCfgPathCostMethod For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value o…	StaPathCostMode Type Values: 1 short 2 long	.1.3.6.1.4.1.259.8.1.9.1.5.6.4.1.16

The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration.

xstInstancePortEntry row .1.3.6.1.4.1.259.8.1.9.1.5.6.5.1

The conceptual row for xstInstancePortTable.

Indexes

xstInstanceCfgIndex BRIDGE-MIBdot1dStpPort

Column	Syntax	OID
xstInstancePortPriority Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active lin…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.3
xstInstancePortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, but do…	Enumeration Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.4
xstInstancePortEnable The enabled/disabled status of the port.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.5
xstInstancePortDesignatedRoot The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.7
xstInstancePortDesignatedCost The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.8
xstInstancePortDesignatedBridge The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.9
xstInstancePortDesignatedPort The port identifier of the port on the designated bridge for this port's segment.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.10
xstInstancePortForwardTransitions The number of times this port has transitioned from the learning state to the forwarding state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.11
xstInstancePortPortRole The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port …	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup 6 master	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.12
xstInstancePortAdminPathCost The admin value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attach…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.13
xstInstancePortOperPathCost The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attache…	Integer32 Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.9.1.5.6.5.1.14

The instance table for the Multiple Spanning Tree region

mstInstanceEditEntry row .1.3.6.1.4.1.259.8.1.9.1.5.6.6.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceEditIndex

Column	Syntax	OID
mstInstanceEditIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 1-64	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.1
mstInstanceEditVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.2
mstInstanceEditVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.3
mstInstanceEditVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.4
mstInstanceEditVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.5
mstInstanceEditRemainingHops The remaining hop count for this MST instance.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.5.6.6.1.6

The Multiple Spanning Tree region instance vlan mapped table.

mstInstanceOperEntry row .1.3.6.1.4.1.259.8.1.9.1.5.6.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceOperIndex

Column	Syntax	OID
mstInstanceOperIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.9.1.5.6.7.1.1
mstInstanceOperVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.7.1.2
mstInstanceOperVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.7.1.3
mstInstanceOperVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.7.1.4
mstInstanceOperVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.5.6.7.1.5

Table for port mirroring, enabling a port to be mirrored
to/from another port. Not all ports can be mirrored and
limitations may apply as to which ports can be used as either
source or destination ports.

mirrorEntry row .1.3.6.1.4.1.259.8.1.9.1.8.1.1

The conceptual row of mirrorTable.

Indexes

mirrorDestinationPort mirrorSourcePort

Column	Syntax	OID
mirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.8.1.1.1
mirrorSourcePort The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.8.1.1.2
mirrorType If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.	Enumerationr/w Enumerated Values: 1 rx 2 tx 3 both	.1.3.6.1.4.1.259.8.1.9.1.8.1.1.3
mirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.8.1.1.4

Table for current router ports.

igmpSnoopRouterCurrentEntry row .1.3.6.1.4.1.259.8.1.9.1.9.8.1

Entry for current router ports.

Indexes

igmpSnoopRouterCurrentVlanIndex

Column	Syntax	OID
igmpSnoopRouterCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.9.8.1.1
igmpSnoopRouterCurrentPorts The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.9.1.9.8.1.2
igmpSnoopRouterCurrentStatus The set of ports which are static multicast router ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.9.1.9.8.1.3

Table for static router ports.

igmpSnoopRouterStaticEntry row .1.3.6.1.4.1.259.8.1.9.1.9.9.1

Entry for static router ports.

Indexes

igmpSnoopRouterStaticVlanIndex

Column	Syntax	OID
igmpSnoopRouterStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.9.9.1.1
igmpSnoopRouterStaticPorts The set of ports which are static router ports.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.9.1.9.9.1.2
igmpSnoopRouterStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.9.9.1.3

Table for current multicast addresses.

igmpSnoopMulticastCurrentEntry row .1.3.6.1.4.1.259.8.1.9.1.9.10.1

Entry for current multicast addresses.

Indexes

igmpSnoopMulticastCurrentVlanIndex igmpSnoopMulticastCurrentIpAddress

Column	Syntax	OID
igmpSnoopMulticastCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.9.10.1.1
igmpSnoopMulticastCurrentIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.9.10.1.2
igmpSnoopMulticastCurrentPorts The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.9.1.9.10.1.3
igmpSnoopMulticastCurrentStatus The set of ports which are static IGMP member ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.9.1.9.10.1.4

Table for static multicast addresses.

igmpSnoopMulticastStaticEntry row .1.3.6.1.4.1.259.8.1.9.1.9.11.1

Entry for static multicast addresses.

Indexes

igmpSnoopMulticastStaticVlanIndex igmpSnoopMulticastStaticIpAddress

Column	Syntax	OID
igmpSnoopMulticastStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.9.11.1.1
igmpSnoopMulticastStaticIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.9.11.1.2
igmpSnoopMulticastStaticPorts The set of ports which are members.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.9.1.9.11.1.3
igmpSnoopMulticastStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.9.11.1.4

Table for enabling or disabling IGMP snooping per VLAN.

igmpSnoopCurrentVlanEntry row .1.3.6.1.4.1.259.8.1.9.1.9.14.1

Entry for enabling or disabling IGMP snooping.

Indexes

igmpSnoopCurrentVlanIndex

Column	Syntax	OID
igmpSnoopCurrentVlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.9.14.1.1
igmpSnoopCurrentVlanImmediateLeave The parameter to enable or disable the Immediate-Leave feature on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.9.14.1.3

A table of netConfigEntry.

ipv6netConfigEntry row .1.3.6.1.4.1.259.8.1.9.1.10.9.1

A set of configuration parameters for a particular ipv6
network interface on this device. If the device has no ipv6 network
interface, this table is empty.

The index is composed of the ifIndex assigned to t…

Indexes

ipv6netConfigIfIndex ipv6netConfigIpAddressType ipv6netConfigIpAddress ipv6netConfigPrefixLength

Column	Syntax	OID
ipv6netConfigIfIndex The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.1
ipv6netConfigIpAddressType The address type of the address associated with this agent. Only ipv6 and ipv6z types are supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.2
ipv6netConfigIpAddress The IPv6 address to which this entry's addressing information pertains.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.3
ipv6netConfigPrefixLength The length of the prefix (in bits) associated with the IPv6 address of this entry.	bitsINET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.4
ipv6netConfigAddrType The type of address. Note that 'stateless(1)' refers to an address that was statelessly autoconfigured; 'stateful(2)' refers to a address which was acquired by via a stateful protocol (e.g. DHCPv6, manual configuration).	Enumeration Enumerated Values: 1 stateless 2 stateful 3 unknown	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.5
ipv6netConfigAddrAnycastFlag This object has the value 'true(1)', if this address is an anycast address and the value 'false(2)' otherwise.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.6
ipv6netConfigAddrStatus The status of an address. Most of the states correspond to states from the IPv6 Stateless Address Autoconfiguration protocol. The preferred(1) state indicates that this is a valid address that can appear…	Enumeration Enumerated Values: 1 preferred 2 deprecated 3 invalid 4 inaccessible 5 unknown 6 tentative 7 duplicate	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.7
ipv6netConfigAddrFlag Determine the way by which final address is generated.	Enumerationr/w Enumerated Values: 1 other 2 eui-64	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.8
ipv6netConfigGeneralPrefixBased The general prefix index associated with the IPv6 address of this entry, and zero value means this address entry is not configurated by any general prefix.	bitsInteger32r/w Constraints: range: 0-256	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.9
ipv6netConfigStatus The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicate…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.9.1.10.9.1.10

Table for DHCP client information listed by interface.
Depending on the nature of the product, this table may
have only one entry(e.g., for the management VLAN), or
may have many entries(e.g., for all ports, or for all
static VLANs).

dhcpcInterfaceEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.1.1.1.1

Entry for DHCP client information listed by interface.

Indexes

dhcpcIfIndex

Column	Syntax	OID
dhcpcIfIndex This is defined by ifIndex in the IF-MIB (static vlan if index).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.11.1.1.1.1.1
dhcpcIfClientIdMode Whether the client ID is in text mode or in hex mode.	Enumerationr/w Enumerated Values: 1 notSpecify 2 text 3 hex	.1.3.6.1.4.1.259.8.1.9.1.10.11.1.1.1.1.2
dhcpcIfClientId The value that the DHCP client sets in the client_id option of DHCPDISCOVER and DHCPREQUEST messages. This value may be used by DHCP servers to uniquely identify the client.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.9.1.10.11.1.1.1.1.3

The table to record the status of dhcpRelay.

dhcpRelayIfEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.2.1.1

A conceptual row of dhcpRelayIfTable.

Indexes

dhcpRelayIfIndex

Column	Syntax	OID
dhcpRelayIfIndex VLAN interface on which this entry is defined.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.11.2.1.1.1
dhcpRelayIfStatus The status of the dhcpRelay. Set this variable to enabled(1) to enable dhcpRelay. Set this variable to disabled(2) to disable dhcpRelay.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.10.11.2.1.1.2

The role of the DHCP relay agent is to forward requests
and replies between server and client when they are not
in the same subnet. To enable DHCP relay service the user needs to
specify relay server IP address and then restart DHCP relay.
This table is to specify relay server IP address,
the maximum number of server IP addresses user can specify is 5.
To restart DHCP relay, please use the dhcpRelayRestart variable.

dhcpRelayServerAddrEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.2.2.1

A conceptual row of dhcpRelayServerAddrTable.

Indexes

dhcpRelayServerAddrIfIndex dhcpRelayServerAddrIndex

Column	Syntax	OID
dhcpRelayServerAddrIfIndex The VLAN interface being used by this table entry.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.11.2.2.1.1
dhcpRelayServerAddrIndex The index of the relay server IP address.	Integer32 Constraints: range: 0-5	.1.3.6.1.4.1.259.8.1.9.1.10.11.2.2.1.2
dhcpRelayServerAddrServerIp The IP address of the relay server.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.2.2.1.3

A DHCP pool is a collection of
user configurations such as option config-lease time
or DNS server IPs, a network address for network pool,
or a host IP plus a hardware address pair for host pool.
However, a DHCP pool only can either be a network pool
or a host pool, or neither (such as that pool only
containing option config no network address config
or a host IP config as well)

dhcpPoolEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1

A conceptual row of dhcpPoolTable.

Indexes

dhcpPoolPoolName

Column	Syntax	OID
dhcpPoolPoolName PoolName; simply specify a string with string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.1
dhcpPoolPoolType Pool Type: notSpecify(1); netWork(2); host(3).	Enumerationr/w Enumerated Values: 1 notSpecify 2 netWork 3 host	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.2
dhcpPoolPoolAddress The DHCP pool address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.3
dhcpPoolSubnetMask The DHCP pool subnet mask.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.4
dhcpPoolHardwareType The DHCP pool hardware type.	Enumerationr/w Enumerated Values: 1 notSpecify 2 ethernet 3 ieee802 4 fddi	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.5
dhcpPoolMacAddress The DHCP pool MAC address.	OctetStringr/w Constraints: range: 6-6	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.6
dhcpPoolstatus Setting this object to valid(1) creates an entry. Setting this object to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.1.1.7

This is the option table of the dhcpPoolTable,
the user can specify option configurations in this table.

dhcpPoolOptionEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1

A conceptual row of dhcpPoolOptionTable.

Indexes

dhcpPoolOptionPoolName

Column	Syntax	OID
dhcpPoolOptionPoolName PoolName, simply specify a string which string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.1
dhcpPoolOptionNextServer Specifies the IP address of the next server in the boot process, which is typically a Trivial File Transfer Protocol(TFTP) server. One IP address is required.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.2
dhcpPoolOptionNetbiosNodeType Specifies the NetBIOS node type. Valid types are: none(1) b-node(2) - Broadcast p-node(3) - Peer-to-peer m-node(4) - Mixed h-node(5) - Hybrid.	Enumerationr/w Enumerated Values: 1 none 2 b-node 3 p-node 4 m-node 5 h-node	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.3
dhcpPoolOptionDomainName Specifies the domain name string.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.4
dhcpPoolOptionBootFile To specify the name of the default boot image.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.5
dhcpPoolOptionLeaseTime To configure the duration of the lease of an IP address that is assigned from a DHCP Server to a DHCP client.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.6
dhcpPoolOptionCidMode Set this variable to text(2) or hex(3) to specify the mode of the client ID, which is useful for the CLI to determine the display method of the client ID. You will get default value 'notSpecify(1)'if this variable has n…	Enumerationr/w Enumerated Values: 1 notSpecify 2 text 3 hex	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.7
dhcpPoolOptionCidBuffer Content of the client ID. You must specify the dhcpPoolOptionCidMode before setting this variable.	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.2.1.8

To specify the DNS IP servers available to a DHCP client,
you can specify up to two addresses for each DHCP pool.

dhcpPoolOptionDnsSerEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.3.1

A conceptual row of dhcpPoolOptionDnsSerTable.

Indexes

dhcpPoolOptionDnsSerPoolName dhcpPoolOptionDnsSerIndex

Column	Syntax	OID
dhcpPoolOptionDnsSerPoolName PoolName, simply specify a string with string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.3.1.1
dhcpPoolOptionDnsSerIndex Index of the DNS server.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.3.1.2
dhcpPoolOptionDnsSerIpAddress IP address of the DNS server.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.3.1.3

Specifices the default router list for a DHCP Client,
you can specify up to two addresses for each DHCP pool.

dhcpPoolOptDefaultRouterEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.4.1

A conceptual row of dhcpPoolOptDefaultRouterTable.

Indexes

dhcpPoolOptDefaultRouterPoolName dhcpPoolOptDefaultRouterIndex

Column	Syntax	OID
dhcpPoolOptDefaultRouterPoolName PoolName, simply specify a string with string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.4.1.1
dhcpPoolOptDefaultRouterIndex Index of the default router.	Integer32 Constraints: range: 1-2	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.4.1.2
dhcpPoolOptDefaultRouterIpAddress Specifies the IP address of a router. One IP address is required.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.4.1.3

To configure the NetBIOS WINS name servers that are available
to DHCP clients. You can specify up to eight addresses for each
DHCP pool.

dhcpPoolOptNetbiosServerEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.5.1

A conceptual row of dhcpPoolOptNetbiosServerTable.

Indexes

dhcpPoolOptNetbiosServerPoolName dhcpPoolOptNetbiosServerIndex

Column	Syntax	OID
dhcpPoolOptNetbiosServerPoolName PoolName, simply specify a string with string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.5.1.1
dhcpPoolOptNetbiosServerIndex Index of the Netbios name Server.	Integer32 Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.5.1.2
dhcpPoolOptNetbiosServerIpAddress Specifies the IP address of the NetBIOS WINS name server. One IP address is required.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.5.1.3

To specify IP addresses that a DHCP Server
should not assign to DHCP clients.

dhcpServerExcludedIpAddrEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.6.1

A conceptual row of dhcpServerExcludedIpAddrTable.

Indexes

dhcpServerExcludedIpAddrLowIp dhcpServerExcludedIpAddrHiIp

Column	Syntax	OID
dhcpServerExcludedIpAddrLowIp The excluded IP address, or first IP address in an excluded address range.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.6.1.1
dhcpServerExcludedIpAddrHiIp The last IP address in the excluded address range.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.6.1.2
dhcpServerExcludedIpAddrStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.6.1.3

To configure the address bindings on the DHCP server.

dhcpServerLeaseBindingEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1

A conceptual row of dhcpServerLeaseBindingTable.

Indexes

dhcpServerLeaseBindingIp

Column	Syntax	OID
dhcpServerLeaseBindingIp The IP address of the host as recorded on the DHCP Server.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1.1
dhcpServerLeaseBindingMac The MAC address of the host as recorded on the DHCP Server.	OctetString Constraints: range: 6-6	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1.2
dhcpServerLeaseBindingLeaseTime The lease expiration date of the IP address of the host.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1.3
dhcpServerLeaseBindingStartTime Show current system real time in sec.	OctetString Constraints: range: 20-20	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1.4
dhcpServerLeaseBindingStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.7.1.5

To specify IP addresses that a DHCP Server
should not assign to DHCP clients.

dhcpPoolActivePoolAddressIpAddrEntry row .1.3.6.1.4.1.259.8.1.9.1.10.11.3.9.1

A conceptual row of dhcpPoolActivePoolAddressTable.

Indexes

dhcpPoolActivePoolName dhcpPoolActivePoolAddressLowIp

Column	Syntax	OID
dhcpPoolActivePoolName PoolName; simply specify a string with string size no more than 8.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.9.1.1
dhcpPoolActivePoolAddressLowIp The first IP address in an active poll address range.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.9.1.2
dhcpPoolActivePoolAddressHiIp The last IP address in the active poll address range.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.11.3.9.1.3

A list of general prefix entries.

ipv6GeneralPrefixEntry row .1.3.6.1.4.1.259.8.1.9.1.10.13.1

One general prefix entry describes an address prefixes list.

Indexes

ipv6GeneralPrefixIndex

Column	Syntax	OID
ipv6GeneralPrefixIndex The index of the general prefix entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.13.1.1
ipv6GeneralPrefixName The name for this general prefix entry.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.259.8.1.9.1.10.13.1.2
ipv6GeneralPrefixStatus The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicat…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.9.1.10.13.1.3

A list of general prefix address entries.

ipv6GeneralPrefixAddrEntry row .1.3.6.1.4.1.259.8.1.9.1.10.14.1

One general prefix address entry describes an address prefix.

Indexes

ipv6GeneralPrefixAddrIndex ipv6GeneralPrefixAddrAddress ipv6GeneralPrefixAddrLength

Column	Syntax	OID
ipv6GeneralPrefixAddrIndex The index in the ipv6GeneralPrefixTable.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.14.1.1
ipv6GeneralPrefixAddrAddress Address prefix value for this general prefix address entry.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.9.1.10.14.1.2
ipv6GeneralPrefixAddrLength The length (in bits) associated with the IPv6 address prefix of this entry.	bitsINET-ADDRESS-MIBInetAddressPrefixLength Type Constraints: range: 0..2040	.1.3.6.1.4.1.259.8.1.9.1.10.14.1.3
ipv6GeneralPrefixAddrStatus The status of this conceptual row entry. This object is used to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicat…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.9.1.10.14.1.4

A table of iPAddrEntry.

iPAddrEntry row .1.3.6.1.4.1.259.8.1.9.1.10.16.1

A set of configuration parameters for a particular
network interface on this device. If the device has no network
interface, this table is empty.

The index is composed of the ifIndex assigned to the
corresp…

Indexes

iPAddrIPAddress iPAddrSubnetMask

Column	Syntax	OID
iPAddrIPAddress The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask is 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out what …	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.1
iPAddrSubnetMask The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the IPAddrIPAddress or IPAddrSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure out wha…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.2
iPAddrIfIndex The VLAN interface being used by this table entry. Only the VLAN interfaces which have an IP configured will appear in the table.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.3
iPAddrPrimaryInterface Whether this is a primary interface.	Enumerationr/w Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.4
iPAddrUnnumbered Whether this is an unnumbered interface.	Enumeration Enumerated Values: 1 unnumbered 2 notUnnumbered	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.5
iPAddrStatus The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicate…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.9.1.10.16.1.6

Table to manage the control of broadcast storms for ports.

bcastStormEntry row .1.3.6.1.4.1.259.8.1.9.1.11.1.1

The conceptual row of bcastStormTable.

Indexes

bcastStormIfIndex

Column	Syntax	OID
bcastStormIfIndex The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.11.1.1.1
bcastStormStatus Whether broadcast storm protection is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.9.1.11.1.1.2
bcastStormPktRate Broadcast storm threshold as packets per second. If this entry is for a trunk, this is the value for each member port.	Integer32r/w Constraints: range: 500-262143	.1.3.6.1.4.1.259.8.1.9.1.11.1.1.4

Table for VLAN configuration.

vlanEntry row .1.3.6.1.4.1.259.8.1.9.1.12.1.1

Entry for VLAN configuration.

Indexes

vlanIndex

Column	Syntax	OID
vlanIndex Based on dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.9.1.12.1.1.1
vlanAddressMethod Method to get the IP address.	Enumerationr/w Enumerated Values: 1 user 2 bootp 3 dhcp	.1.3.6.1.4.1.259.8.1.9.1.12.1.1.2

Table for port configuration in VLAN.

vlanPortEntry row .1.3.6.1.4.1.259.8.1.9.1.12.2.1

Entry for port configuration in VLAN.

Indexes

vlanPortIndex

Column	Syntax	OID
vlanPortIndex The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qPvid in the Q-BRIDG…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.12.2.1.1
vlanPortMode This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link.	Enumerationr/w Enumerated Values: 1 hybrid 2 dot1qTrunk	.1.3.6.1.4.1.259.8.1.9.1.12.2.1.2

Table for port configuration in 802.1Q Tunneling.

vlanDot1qTunnelPortEntry row .1.3.6.1.4.1.259.8.1.9.1.12.6.1

Entry for port configuration in 802.1Q Tunneling.

Indexes

vlanDot1qTunnelPortIndex

Column	Syntax	OID
vlanDot1qTunnelPortIndex The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.12.6.1.1
vlanDot1qTunnelPortMode This variable sets the 802.1Q Tunneling mode. Setting it to none(1) indicates no mode in this port. Setting it to dot1qTunnel(2) sets as dot1q-tunnel mode port which link to customer. Setting it to dot1qTunnelUplink(3) …	Enumerationr/w Enumerated Values: 1 none 2 dot1qTunnel 3 dot1qTunnelUplink	.1.3.6.1.4.1.259.8.1.9.1.12.6.1.2
vlanDot1qTunnelPortEtherType TPID for 802.1Q encapsulation. It's used to select a nonstandard (nondefault) 2-byte ethertype to identify 802.1Q tagged frames.	Unsigned32r/w Constraints: range: 32768-65535	.1.3.6.1.4.1.259.8.1.9.1.12.6.1.3

Table for IP precedence priority mapping.

prioIpPrecEntry row .1.3.6.1.4.1.259.8.1.9.1.13.2.1

Entry for IP precedence priority mapping.

Indexes

prioIpPrecPort prioIpPrecValue

Column	Syntax	OID
prioIpPrecPort The port or the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.13.2.1.2
prioIpPrecValue Value of IP ToS Precedence as specified in the packet header.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.9.1.13.2.1.3
prioIpPrecCos Class of Service (CoS) as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The IP ToS precedence value in the same table row will be mapped to this CoS. This CoS is then further mapped to the hardware queue acc…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.9.1.13.2.1.4

Table for IP DSCP priority mapping.

prioIpDscpEntry row .1.3.6.1.4.1.259.8.1.9.1.13.4.1

Entry for IP DSCP priority mapping.

Indexes

prioIpDscpPort prioIpDscpValue

Column	Syntax	OID
prioIpDscpPort The port and the trunk (excluding trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.13.4.1.1
prioIpDscpValue Value of IP DSCP as specified in the packet header.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.9.1.13.4.1.2
prioIpDscpCos Class of Service as defined by dot1dTrafficClassPriority in the P-BRIDGE-MIB. The prioIpDscpValue value in the same table row will be mapped to this Class of Service (CoS). This CoS is then further mapped to the hardwar…	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.9.1.13.4.1.3

Table for IP port priority mapping.

prioIpPortEntry row .1.3.6.1.4.1.259.8.1.9.1.13.7.1

Entry for IP port priority mapping.

Indexes

prioIpPortPhysPort prioIpPortValue

Column	Syntax	OID
prioIpPortPhysPort The port or the trunk (excluding trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.13.7.1.1
prioIpPortValue IP port for this value.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.9.1.13.7.1.2
prioIpPortCos Class of service for this entry.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.9.1.13.7.1.3
prioIpPortStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.9.1.13.7.1.4

Table for per port weighted round robin (WRR).

prioWrrPortEntry row .1.3.6.1.4.1.259.8.1.9.1.13.12.1

Entry for per port weighted round robin (WRR).

Indexes

prioWrrPortIfIndex prioWrrPortTrafficClass

Column	Syntax	OID
prioWrrPortIfIndex The port interface of the prioWrrPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.9.1.13.12.1.1
prioWrrPortTrafficClass Traffic class for this entry, as defined in dot1dTrafficClass in the P-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.9.1.13.12.1.2
prioWrrPortWeight Weight for this entry.	Integer32r/w Constraints: range: 1-15	.1.3.6.1.4.1.259.8.1.9.1.13.12.1.3