ES3526XA_ES3510-MIB Table View

Table of descriptive and status information about
switches in this system.

switchInfoEntry row .1.3.6.1.4.1.259.8.1.5.1.1.3.1

An entry in the table, containing information
about a single switch in this system.

Indexes

swUnitIndex

Column	Syntax	OID
swUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.1
swHardwareVer Hardware version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.2
swMicrocodeVer Microcode version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.3
swLoaderVer Loader version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.4
swBootRomVer Boot ROM code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.5
swOpCodeVer Operation code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.6
swPortNumber The total port number of this switch (including expansion slot).	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.7
swPowerStatus Indicates the switch using internalPower(1), redundantPower(2) or both(3)	Enumeration Enumerated Values: 1 internalPower 2 redundantPower 3 internalAndRedundantPower	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.8
swRoleInSystem Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.	Enumeration Enumerated Values: 1 master 2 backupMaster 3 slave	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.9
swSerialNumber Serial number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.10
swServiceTag Service tag serial-number of the switch.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.8.1.5.1.1.3.1.13

Table of descriptive and status information about
configuration of each switch port (including expansion slot)
in this system. This table also contains information
about each trunk (similar to Cisco's EtherChannel).

portEntry row .1.3.6.1.4.1.259.8.1.5.1.2.1.1

An entry in the table, containing information
about configuration in one switch port of the switch.

Indexes

portIndex

Column	Syntax	OID
portIndex This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.1
portName Indicates the port name. This is same as ifAlias in the IF-MIB (RFC2863 or later).	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.2
portType Indicates the port type.	Enumeration Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseSfp 9 hundredBaseFxScSingleMode 10 hundredBaseFxScMultiMode	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.3
portSpeedDpxCfg Set the port speed and duplex mode as follows: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half duplex mode fullDuplex100(5) - 100…	Enumerationr/w Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism. When the port is operating in…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled 3 backPressure 4 dot3xFlowControl	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.5
portCapabilities Port capabilities.	Bitsr/w Enumerated Values: 0 portCap10half 1 portCap10full 2 portCap100half 3 portCap100full 4 portCap1000half 5 portCap1000full 6 reserved6 7 reserved7 8 reserved8 9 reserved9 10 reserved10 11 reserved11 12 reserved12 13 reserved13 14 portCapSym 15 portCapFlowCtrl	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.6
portAutonegotiation Whether autonegotiation is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port. If this index is a trunk, the speed is the speed of its individual members. If this index is a trunk and the result is inconsistent among its member ports, this …	Enumeration Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.8
portFlowCtrlStatus (2) BackPressure flow control machanism is used. (3) IEEE 802.3 flow control machanism is used. (4) Flow control mechanism is disabled. If this index is a trunk and the result is inconsistent among its member ports, thi…	Enumeration Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.9
portTrunkIndex The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to trunk at trunkIndex, defined by the corresponding trunkPort…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.2.1.1.10

Table of descriptive and status information about
configuration of each trunk,
similar to Cisco EtherChannel.

trunkEntry row .1.3.6.1.4.1.259.8.1.5.1.3.3.1

An entry in the table, containing information
about configuration in one trunk of the switch.

Indexes

trunkIndex

Column	Syntax	OID
trunkIndex This object identifies the trunk within the switch for which this entry contains information.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.3.3.1.1
trunkPorts The complete set of ports currently associated with this trunk.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.5.1.3.3.1.2
trunkCreation A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.	Enumeration Enumerated Values: 1 static 2 lacp	.1.3.6.1.4.1.259.8.1.5.1.3.3.1.3
trunkStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.3.3.1.4

Table for LACP port configuration.

lacpPortEntry row .1.3.6.1.4.1.259.8.1.5.1.4.1.1

Entry for LACP port configuration.

Indexes

lacpPortIndex

Column	Syntax	OID
lacpPortIndex This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.4.1.1.1
lacpPortStatus Whether 802.3ad LACP is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.4.1.1.2

The table manages port settings for Spanning Tree 
Protocol 802.1d, 802.1w or 802.1s depending on the 
value specified by staProtocolType.

staPortEntry row .1.3.6.1.4.1.259.8.1.5.1.5.2.1

The conceptual entry of staPortTable.

Indexes

staPortIndex

Column	Syntax	OID
staPortIndex The port and the trunk (excluding trunk member ports) interface of the staPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1dStpPort i…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.1
staPortFastForward Whether fast forwarding is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.2
staPortProtocolMigration When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.3
staPortAdminEdgePort The administrative value of the edge port parameter. A value of true(1) indicates that this port should be assumed as an edge-port and a value of false(2) indicates that this port should be assumed as a non-edge-port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.4
staPortOperEdgePort The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.5
staPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of for…	Enumerationr/w Enumerated Values: 0 forceTrue 1 forceFalse 2 auto	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.6
staPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-de…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.7
staPortLongPathCost The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This object is used to configure the spanning tree port path cost in the …	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.8
staPortSystemStatus Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.5.2.1.9

This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0.

xstInstanceCfgEntry row .1.3.6.1.4.1.259.8.1.5.1.5.6.4.1

A conceptual row containing the property of the RST or MST instance.

Indexes

xstInstanceCfgIndex

Column	Syntax	OID
xstInstanceCfgIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.1
xstInstanceCfgPriority The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.	Integer32r/w Constraints: range: 0-61440	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.2
xstInstanceCfgTimeSinceTopologyChange The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.3
xstInstanceCfgTopChanges The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.4
xstInstanceCfgDesignatedRoot The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identi…	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.5
xstInstanceCfgRootCost The cost of the path to the root as seen from this bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.6
xstInstanceCfgRootPort The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.7
xstInstanceCfgMaxAge The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is t…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.8
xstInstanceCfgHelloTime The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.9
xstInstanceCfgHoldTime This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.10
xstInstanceCfgForwardDelay For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the por…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.11
xstInstanceCfgBridgeMaxAge For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the val…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.12
xstInstanceCfgBridgeHelloTime For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.13
xstInstanceCfgBridgeForwardDelay For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.14
xstInstanceCfgTxHoldCount For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.15
xstInstanceCfgPathCostMethod For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value o…	StaPathCostMode Type Values: 1 short 2 long	.1.3.6.1.4.1.259.8.1.5.1.5.6.4.1.16

The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration.

xstInstancePortEntry row .1.3.6.1.4.1.259.8.1.5.1.5.6.5.1

The conceptual row for xstInstancePortTable.

Indexes

xstInstancePortInstance xstInstancePortPort

Column	Syntax	OID
xstInstancePortInstance The instance of the MSTP.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.1
xstInstancePortPort The port and the trunk (excluding trunk member ports) interface of the mstInstancePortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of dot1dStp…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.2
xstInstancePortPriority Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active lin…	Integer32r/w Constraints: range: 0-240	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.3
xstInstancePortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, …	Enumeration Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.4
xstInstancePortEnable The enabled/disabled status of the port.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.5
xstInstancePortPathCost The pathcost of the RST or MST in the range 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster media, and higher val…	Integer32r/w Constraints: range: 1-200000000	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.6
xstInstancePortDesignatedRoot The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.7
xstInstancePortDesignatedCost The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.8
xstInstancePortDesignatedBridge The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.9
xstInstancePortDesignatedPort The port identifier of the port on the designated bridge for this port's segment.	OctetString Constraints: range: 2-2	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.10
xstInstancePortForwardTransitions The number of times this port has transitioned from the learning state to the forwarding state.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.11
xstInstancePortPortRole The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port …	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup 6 master	.1.3.6.1.4.1.259.8.1.5.1.5.6.5.1.12

The Multiple Spanning Tree region instance vlan configuration table.
Please read the actual instance vlan mapped in the mstInstanceOperTable.

mstInstanceEditEntry row .1.3.6.1.4.1.259.8.1.5.1.5.6.6.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceEditIndex

Column	Syntax	OID
mstInstanceEditIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.1
mstInstanceEditVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.2
mstInstanceEditVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.3
mstInstanceEditVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.4
mstInstanceEditVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.5
mstInstanceEditRemainingHops The remaining hop count for this MST instance.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.5.6.6.1.6

The Multiple Spanning Tree region instance vlan mapped table.

mstInstanceOperEntry row .1.3.6.1.4.1.259.8.1.5.1.5.6.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

mstInstanceOperIndex

Column	Syntax	OID
mstInstanceOperIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32 Constraints: range: 0-4094	.1.3.6.1.4.1.259.8.1.5.1.5.6.7.1.1
mstInstanceOperVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.7.1.2
mstInstanceOperVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.7.1.3
mstInstanceOperVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.7.1.4
mstInstanceOperVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.8.1.5.1.5.6.7.1.5

A table provides the mechanism to configure the 
spanning tree loopback detection of each port or trunk

staLoopbackDetectionPortEntry row .1.3.6.1.4.1.259.8.1.5.1.5.7.1

A conceptual row of staLoopbackDetectionPortTable.

Indexes

staLoopbackDetectionPortIfIndex

Column	Syntax	OID
staLoopbackDetectionPortIfIndex The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.8.1.5.1.5.7.1.1
staLoopbackDetectionPortStatus Status of the port on whether spanning tree loopback detection is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.5.7.1.2
staLoopbackDetectionPortTrapStatus The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.5.7.1.3
staLoopbackDetectionPortReleaseMode Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state man…	Enumerationr/w Enumerated Values: 1 auto 2 manual	.1.3.6.1.4.1.259.8.1.5.1.5.7.1.4
staLoopbackDetectionPortRelease Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.	Enumerationr/w Enumerated Values: 1 noRelease 2 release	.1.3.6.1.4.1.259.8.1.5.1.5.7.1.5

Table of descriptive and status information about
switches in this system.

mirrorEntry row .1.3.6.1.4.1.259.8.1.5.1.8.1.1

An entry in the table, containing information
about a single switch in this system.

Indexes

mirrorDestinationPort mirrorSourcePort

Column	Syntax	OID
mirrorDestinationPort Destination port for mirrored packets. This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.8.1.1.1
mirrorSourcePort Source port for mirrored packets. This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.8.1.1.2
mirrorType If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), receive and transmit packets will be mirrored.	Enumerationr/w Enumerated Values: 1 rx 2 tx 3 both	.1.3.6.1.4.1.259.8.1.5.1.8.1.1.3
mirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.8.1.1.4

Table for current router ports.

igmpSnoopRouterCurrentEntry row .1.3.6.1.4.1.259.8.1.5.1.9.8.1

Entry for current router ports.

Indexes

igmpSnoopRouterCurrentVlanIndex

Column	Syntax	OID
igmpSnoopRouterCurrentVlanIndex This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.8.1.1
igmpSnoopRouterCurrentPorts The set of ports which are current router ports. Within this list, some router ports are static router ports. Please refer to igmpSnoopRouterStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.5.1.9.8.1.2
igmpSnoopRouterCurrentStatus The set of ports which are static router ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.5.1.9.8.1.3

Table for static router ports.

igmpSnoopRouterStaticEntry row .1.3.6.1.4.1.259.8.1.5.1.9.9.1

Entry for static router ports.

Indexes

igmpSnoopRouterStaticVlanIndex

Column	Syntax	OID
igmpSnoopRouterStaticVlanIndex This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.9.1.1
igmpSnoopRouterStaticPorts The set of ports which are static router ports.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.5.1.9.9.1.2
igmpSnoopRouterStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.9.9.1.3

Table for current multicast addresses.

igmpSnoopMulticastCurrentEntry row .1.3.6.1.4.1.259.8.1.5.1.9.10.1

Entry for current multicast addresses.

Indexes

igmpSnoopMulticastCurrentVlanIndex igmpSnoopMulticastCurrentIpAddress

Column	Syntax	OID
igmpSnoopMulticastCurrentVlanIndex This is defined as dot1qVlanIndex in the Q-BRIDGE-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.10.1.1
igmpSnoopMulticastCurrentIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.5.1.9.10.1.2
igmpSnoopMulticastCurrentPorts The set of ports which are members.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.5.1.9.10.1.3
igmpSnoopMulticastCurrentStatus The set of ports which are static members.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.8.1.5.1.9.10.1.4

Table for static multicast addresses.

igmpSnoopMulticastStaticEntry row .1.3.6.1.4.1.259.8.1.5.1.9.11.1

Entry for static multicast addresses.

Indexes

igmpSnoopMulticastStaticVlanIndex igmpSnoopMulticastStaticIpAddress

Column	Syntax	OID
igmpSnoopMulticastStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.11.1.1
igmpSnoopMulticastStaticIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.5.1.9.11.1.2
igmpSnoopMulticastStaticPorts The set of ports which are members.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.8.1.5.1.9.11.1.3
igmpSnoopMulticastStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.9.11.1.4

Table for enabling or disabling IGMP snooping per VLAN.

igmpSnoopCurrentVlanEntry row .1.3.6.1.4.1.259.8.1.5.1.9.14.1

Entry for enabling or disabling IGMP snooping.

Indexes

igmpSnoopCurrentVlanIndex

Column	Syntax	OID
igmpSnoopCurrentVlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.14.1.1
igmpSnoopCurrentVlanImmediateLeave The parameter to enable or disable the Immediate-Leave feature on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.9.14.1.3

The table for configuring the IGMP snooping profile.

igmpSnoopProfileEntry row .1.3.6.1.4.1.259.8.1.5.1.9.18.1

The entry for configuring the IGMP snooping profile.

Indexes

igmpSnoopProfileId

Column	Syntax	OID
igmpSnoopProfileId The ID of the IGMP snooping profile.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.18.1.1
igmpSnoopProfileAction The access mode of the IGMP snooping profile.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.5.1.9.18.1.2
igmpSnoopProfileStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.9.18.1.3

The table for configuring the range of the IGMP snooping profile.

igmpSnoopProfileRangeEntry row .1.3.6.1.4.1.259.8.1.5.1.9.20.1

The entry for configuring the range of the IGMP snooping profile.

Indexes

igmpSnoopProfileRangeProfileId igmpSnoopProfileRangeInetAddressType igmpSnoopProfileRangeStartInetAddress

Column	Syntax	OID
igmpSnoopProfileRangeProfileId This is defined as igmpSnoopProfileId.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.20.1.1
igmpSnoopProfileRangeInetAddressType The address type is associated with this agent. Only ipv4(1) type is supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.259.8.1.5.1.9.20.1.2
igmpSnoopProfileRangeStartInetAddress The specified addresses in the start of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.5.1.9.20.1.3
igmpSnoopProfileRangeEndInetAddress The specified addresses in the end of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.8.1.5.1.9.20.1.4
igmpSnoopProfileRangeAction The access mode of the IGMP snooping profile.	Enumeration Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.5.1.9.20.1.5

Table for port configuration in IGMP filtering.

igmpSnoopFilterPortEntry row .1.3.6.1.4.1.259.8.1.5.1.9.21.1

Entry for port configuration in IGMP filtering.

Indexes

igmpSnoopFilterPortIndex

Column	Syntax	OID
igmpSnoopFilterPortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.21.1.1
igmpSnoopFilterPortProfileId The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTab…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.9.21.1.2

Table for port configuration in IGMP throttling.

igmpSnoopThrottlePortEntry row .1.3.6.1.4.1.259.8.1.5.1.9.22.1

Entry for port configuration in IGMP throttling.

Indexes

igmpSnoopThrottlePortIndex

Column	Syntax	OID
igmpSnoopThrottlePortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.9.22.1.1
igmpSnoopThrottlePortRunningStatus Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.8.1.5.1.9.22.1.2
igmpSnoopThrottlePortAction The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to t…	Enumerationr/w Enumerated Values: 1 replace 2 deny	.1.3.6.1.4.1.259.8.1.5.1.9.22.1.3
igmpSnoopThrottlePortMaxGroups The maximum number of IGMP groups that the interface can join.	Integer32r/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.5.1.9.22.1.4
igmpSnoopThrottlePortCurrentGroups The current number of IGMP groups that the interface has joined.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.9.22.1.5

A table of netConfigEntries.

netConfigEntry row .1.3.6.1.4.1.259.8.1.5.1.10.1.1

A set of configuration parameters for a particular
network interface on this device. If the device has no network
interface, this table is empty.

The index is composed of the ifIndex assigned to the
corresp…

Indexes

netConfigIfIndex netConfigIPAddress netConfigSubnetMask

Column	Syntax	OID
netConfigIfIndex VLAN interface on which this entry is defined. This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.1
netConfigIPAddress The IP address of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure ou…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.2
netConfigSubnetMask The subnet mask of this Net interface. The default value for this object is 0.0.0.0. If either the netConfigIPAddress or netConfigSubnetMask are 0.0.0.0, then when the device boots, it may use BOOTP to try to figure o…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.3
netConfigPrimaryInterface Whether this is a primary interface.	Enumerationr/w Enumerated Values: 1 primary 2 secondary	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.4
netConfigUnnumbered Whether this is an unnumbered interface.	Enumerationr/w Enumerated Values: 1 unnumbered 2 notUnnumbered	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.5
netConfigStatus The status of this netConfigEntry. An entry may not exist in the active state unless all objects in the entry have an appropriate value.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.10.1.1.6

Table of descriptive and status information about
configuration of each switch ports(including expansion slot)
in this system.

bcastStormEntry row .1.3.6.1.4.1.259.8.1.5.1.11.1.1

An entry in the table, containing information
about configuration in one switch port of the switch.

Indexes

bcastStormIfIndex

Column	Syntax	OID
bcastStormIfIndex This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.11.1.1.1
bcastStormStatus Whether broadcast storm protection is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.11.1.1.2
bcastStormOctetRateLevel Broadcast storm level.	Integer32r/w Constraints: range: 1-127	.1.3.6.1.4.1.259.8.1.5.1.11.1.1.5

Table for VLAN configuration.

vlanEntry row .1.3.6.1.4.1.259.8.1.5.1.12.1.1

Entry for VLAN configuration.

Indexes

vlanIndex

Column	Syntax	OID
vlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.8.1.5.1.12.1.1.1
vlanAddressMethod Method to get the IP address.	Enumerationr/w Enumerated Values: 1 user 2 bootp 3 dhcp	.1.3.6.1.4.1.259.8.1.5.1.12.1.1.2

Table for port configuration in VLAN.

vlanPortEntry row .1.3.6.1.4.1.259.8.1.5.1.12.2.1

Entry for port configuration in VLAN.

Indexes

vlanPortIndex

Column	Syntax	OID
vlanPortIndex This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.12.2.1.1
vlanPortMode This variable sets the 802.1Q VLAN mode. Setting it to hybrid(1) sets a hybrid link. Setting it to dot1qTrunk(2) sets a trunk link. Setting it to access(3) sets an access link,but it is not supported in LEO product.	Enumerationr/w Enumerated Values: 1 hybrid 2 dot1qTrunk 3 access	.1.3.6.1.4.1.259.8.1.5.1.12.2.1.2
vlanPortPrivateVlanType The port type defined for Private vlan.	Enumerationr/w Enumerated Values: 1 normal 2 isolated 3 community 4 promiscous	.1.3.6.1.4.1.259.8.1.5.1.12.2.1.3

Table for IP precedence priority mapping.

prioIpPrecEntry row .1.3.6.1.4.1.259.8.1.5.1.13.2.1

Entry for IP precendence priority mapping.

Indexes

prioIpPrecPort prioIpPrecValue

Column	Syntax	OID
prioIpPrecPort This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.13.2.1.2
prioIpPrecValue Precedence value for this entry.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.2.1.3
prioIpPrecCos Class of service for this entry.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.2.1.4

Table for IP DSCP priority mapping.

prioIpDscpEntry row .1.3.6.1.4.1.259.8.1.5.1.13.4.1

Entry for IP DSCP priority mapping.

Indexes

prioIpDscpPort prioIpDscpValue

Column	Syntax	OID
prioIpDscpPort This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.13.4.1.1
prioIpDscpValue DSCP value for this entry.	Integer32 Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.5.1.13.4.1.2
prioIpDscpCos Class of service for this entry.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.4.1.3

Table for IP port priority mapping.

prioIpPortEntry row .1.3.6.1.4.1.259.8.1.5.1.13.7.1

Entry for IP port priority mapping.

Indexes

prioIpPortPhysPort prioIpPortValue

Column	Syntax	OID
prioIpPortPhysPort This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.13.7.1.1
prioIpPortValue IP port for this value.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.5.1.13.7.1.2
prioIpPortCos Class of service for this entry.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.7.1.3
prioIpPortStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry.	Enumerationr/w Enumerated Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.13.7.1.4

Table for weighted round robin (WRR).

prioWrrEntry row .1.3.6.1.4.1.259.8.1.5.1.13.9.1

Entry for weighted round robin (WRR).

Indexes

prioWrrTrafficClass

Column	Syntax	OID
prioWrrTrafficClass Traffic class for this entry, as defined in dot1dTrafficClass in the Q-BRIDGE-MIB. The actual maximum depends on the hardware, and is equal to dot1dPortNumTrafficClasses-1.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.9.1.1
prioWrrWeight Weight for this entry.	Integer32r/w Constraints: range: 1-31	.1.3.6.1.4.1.259.8.1.5.1.13.9.1.2

Table for IP tos priority mapping.

prioIpTosEntry row .1.3.6.1.4.1.259.8.1.5.1.13.11.1

Entry for IP tos priority mapping.

Indexes

prioIpTosPort prioIpTosValue

Column	Syntax	OID
prioIpTosPort This is defined as ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.13.11.1.2
prioIpTosValue Tos value for this entry.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.11.1.3
prioIpTosCos Class of service for this entry.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.13.11.1.4

A list of trap destination entries.

trapDestEntry row .1.3.6.1.4.1.259.8.1.5.1.14.1.1

A destination entry describes the destination IP address,
the community string, and SNMP version to use when sending
a trap.

Indexes

trapDestAddress

Column	Syntax	OID
trapDestAddress The address to send traps.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.8.1.5.1.14.1.1.1
trapDestCommunity A community to which this destination address belongs.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.5.1.14.1.1.2
trapDestStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.8.1.5.1.14.1.1.3
trapDestVersion Determines the version of the trap that is to be sent to the trap receiver. If the value is 1, then an SNMP version 1 trap is sent and if the value is 2, an SNMP version 2 trap is sent.	Enumerationr/w Enumerated Values: 1 version1 2 version2	.1.3.6.1.4.1.259.8.1.5.1.14.1.1.4
trapDestUdpPort Determines the UDP port number that the trap will be sent to.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.5.1.14.1.1.5

Table for rate limit of each port.

rateLimitPortEntry row .1.3.6.1.4.1.259.8.1.5.1.16.1.2.1

Entry for rate limit of each port.

Indexes

rlPortIndex

Column	Syntax	OID
rlPortIndex The port and the trunk (including trunk member) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.1
rlPortInputStatus Whether input rate limit is enabled for this port.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.6
rlPortOutputStatus Whether output rate limit is enabled for this port.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.7
rlPortInputLevel The Level of the input rate limit.all ports range is 1..127	Integer32r/w Constraints: range: 1-127	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.8
rlPortInputScale Rate Limit scale as octets per second. If this is scale-10m(0), then Rate Limit scale as 10M bytes per second, If this is scale-1m(1), then Rate Limit scale as 1M bytes per second, If this is scale-100k(2), then Rate Li…	Enumerationr/w Enumerated Values: 0 scale-10m 1 scale-1m 2 scale-100k 3 scale-10k 4 scale-1k	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.9
rlPortOutputLevel The Level of the output rate limit.all ports range is 1..127	Integer32r/w Constraints: range: 1-127	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.10
rlPortOutputScale Rate Limit scale as octets per second. If this is scale-10m(0), then Rate Limit scale as 10M bytes per second, If this is scale-1m(1), then Rate Limit scale as 1M bytes per second, If this is scale-100k(2), then Rate Li…	Enumerationr/w Enumerated Values: 0 scale-10m 1 scale-1m 2 scale-100k 3 scale-10k 4 scale-1k	.1.3.6.1.4.1.259.8.1.5.1.16.1.2.1.11

Table for ACL to CoS Mapping.

prioAclToCosMappingEntry row .1.3.6.1.4.1.259.8.1.5.1.16.3.1.1

Entry for ACL to CoS Mapping.

Indexes

prioAclToCosMappingIfIndex prioAclToCosMappingAclName

Column	Syntax	OID
prioAclToCosMappingIfIndex The port interface of the prioAclToCosMappingEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.3.1.1.1
prioAclToCosMappingAclName The name of an IP ACL. Within a feature a unique name is used to identify the list to which the entry belongs in the device.	OctetString Constraints: range: 1-15	.1.3.6.1.4.1.259.8.1.5.1.16.3.1.1.2
prioAclToCosMappingCosValue CoS value of the prioAclToCosMappingTable.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.16.3.1.1.3
prioAclToCosMappingStatus The status of this conceptual row entry. This object isused to manage the creation and deletion of conceptual rows. The status column has six defined values: - 'active', which indicate…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.3.1.1.4

Table for differentiated services on each port.

diffServPortEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.9.1

Entry for differentiated services on each port.

Indexes

diffServPortIfIndex

Column	Syntax	OID
diffServPortIfIndex This object is the interface index of diffServPortEntry. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.9.1.1
diffServPortPolicyMapIndex Specifies the policy map binding to the interface. The policy map identified by a particular value of this index is associated with the same DiffServPolicyMapEntry as identified by the same value of diffServPolicyMapInd…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.9.1.2
diffServPortIngressIpAclIndex Specifies the ingress IP ACL binding to the interface. The ingress IP ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.9.1.3
diffServPortIngressMacAclIndex Specifies the ingress MAC ACL binding to the interface. The ingress MAC ACL identified by a particular value of this index is associated with the same diffServAclEntry as identified by the same value of diffServAclIndex.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.9.1.4

Table for policy map.

diffServPolicyMapEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.10.1

Entry for policy map.

Indexes

diffServPolicyMapIndex

Column	Syntax	OID
diffServPolicyMapIndex An index that uniquely identifies an entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.10.1.1
diffServPolicyMapName The name of this entry.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.259.8.1.5.1.16.4.10.1.2
diffServPolicyMapDescription The description of this entry.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.5.1.16.4.10.1.3
diffServPolicyMapElementIndexList The octet string containes the diffServPolicyMapElementEntry indexes. Two octets express one index and it is represented in network order. This index list indicates the diffServPolicyMapEntrys which belong to this entry.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.8.1.5.1.16.4.10.1.4
diffServPolicyMapStatus This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'active', which indi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.10.1.5

Table for policy map element.

diffServPolicyMapElementEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.12.1

Entry for policy map element.

Indexes

diffServPolicyMapElementIndex

Column	Syntax	OID
diffServPolicyMapElementIndex An index that uniquely identifies an entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.12.1.1
diffServPolicyMapElementClassMapIndex Specifies the class map binding to this entry. The class map identified by a particular value of this index is associated with the same diffServClassMapEntry as identified by the same value of diffServClassMapIndex.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.12.1.2
diffServPolicyMapElementMeterIndex Specifies the meter binding to this entry. The meter identified by a particular value of this index is associated with the same diffServMeterEntry as identified by the same value of diffServMeterIndex. If this value is …	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.12.1.3
diffServPolicyMapElementActionIndex Specifies the action binding to this entry. The action identified by a particular value of this index is associated with the same diffServActionEntry as identified by the same value of diffServActionIndex.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.12.1.4
diffServPolicyMapElementStatus This object is used to create a new row, or modify or delete an existing row, in this table. The status column has six defined values: The status column has six defined values: - 'acti…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.12.1.5

Table for class map.

diffServClassMapEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.13.1

Entry for class map.

Indexes

diffServClassMapIndex

Column	Syntax	OID
diffServClassMapIndex An index that uniquely identifies an entry in this table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.1
diffServClassMapName The name of this entry.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.2
diffServClassMapDescription The description of this entry.	OctetStringr/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.3
diffServClassMapMatchType The map match type of this entry.	Enumerationr/w Enumerated Values: 1 matchAny 2 matchAll	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.4
diffServClassMapElementIndexTypeList The octet string containes the type of class map element indexes. Two octets which are represented in network order express one type of the class map element index in network order and it maps the index of differServCla…	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.5
diffServClassMapElementIndexList The octet string containes the class map element indexes. Two octets express one index and it is represented in network order. This index list indicates the particular class map elements which belong to this table. The …	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.6
diffServClassMapStatus This object is used to create a new row or modify or delete an existing row in this table.The status column has six defined values: The status column has six defined values: - 'active'…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.13.1.7

Table for ACL.

diffServAclEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.15.1

Entry for ACL.

Indexes

diffServAclIndex

Column	Syntax	OID
diffServAclIndex An index that uniquely identifies an entry in the ACL table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.15.1.1
diffServAclName The name of this entry.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.259.8.1.5.1.16.4.15.1.2
diffServAclType The type of this entry. When the value of ACL type is modified, then the ACEs in the diffServAclAceIndexList of this entry will be auto-removed, and this entry will be aoto- unbound from the diffServPortTable and the di…	Enumerationr/w Enumerated Values: 1 mac 2 ipstandard 3 ipextended	.1.3.6.1.4.1.259.8.1.5.1.16.4.15.1.3
diffServAclAceIndexList The octet string containes the ACE indexes. Two octets express one index and it is represented in network order. This index list indicates the particular ACEs which belong to this table. The ACE uses type to indicate th…	OctetString Constraints: range: 0-255	.1.3.6.1.4.1.259.8.1.5.1.16.4.15.1.4
diffServAclStatus This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: - 'active', which indicates that the conceptual row is availa…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.15.1.5

Table for IP ACE.

diffServIpAceEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.17.1

Entry for IP ACE.

Indexes

diffServIpAceIndex

Column	Syntax	OID
diffServIpAceIndex An index that uniquely identifies an entry in the IP ACE table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.1
diffServIpAceType The specified IP ACE type. When the type of this entry is modified, then this entry will be auto-unbound from the diffServAclEntry and the not supporting field of this entry will be set 0.	Enumerationr/w Enumerated Values: 1 standard 2 extended	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.2
diffServIpAceAccess Indicates the action to be taken if a packet matches this ACE.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.3
diffServIpAceSourceIpAddr The specified source IP address. The packet's source address is AND-ed with the value of IpAceSourceIpAddrBitmask and then compared against the value of this object.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.4
diffServIpAceSourceIpAddrBitmask The specified source IP address mask. The packet's source address is AND-ed with the value of IpAceSourceIpAddr and then compared against the value of this object.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.5
diffServIpAceDestIpAddr The specified destination IP address. The packet's destination address is AND-ed with the value of diffServIpAceDestIpAddrBitmask and then compared against the value of this object. This object may not be modified if th…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.6
diffServIpAceDestIpAddrBitmask The specified destination IP address mask. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.7
diffServIpAceProtocol The protocol number field in the IP header used to indicate the higher layer protocol as specified in RFC 1700. A value of 0 matches every IP packet. The object=256 means 'any'. For example: 0 is IP, 1 is ICMP, 2 is IGM…	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.8
diffServIpAcePrec Specifies the IP precedence value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 8. This object may not be modified if the associated diffServIpAceType object is …	Integer32r/w Constraints: range: 0-8	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.9
diffServIpAceTos Specifies the IP ToS facility value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 9. This object may not be modified if the associated diffServIpAceType object i…	Integer32r/w Constraints: range: 0-16	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.10
diffServIpAceDscp Specifies the DSCP value to match against. The value of this object is ignored whenever the value of diffServIpAcePrec object is 64. This object may not be modified if the associated diffServIpAceType object is equal to…	Integer32r/w Constraints: range: 0-64	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.11
diffServIpAceSourcePortOp Indicates how a packet's source TCP/UDP port number is to be compared. noOperator(1), which is the default value, means no comparison is to be made with the source TCP/UDP port number. equal(2), which is used the diffSe…	Enumerationr/w Enumerated Values: 1 noOperator 2 equal 3 range	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.12
diffServIpAceMinSourcePort If the diffServIpAceSourcePortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.13
diffServIpAceMaxSourcePort If the diffServIpAceSourcePortOp is range(3), this indicates the upper bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.14
diffServIpAceSourcePortBitmask If the diffServIpAceSourcePortOp is equal(2), this indicates the bitmask of the diffServIpAceMinSourcePort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.15
diffServIpAceDestPortOp Indicates how a packet's destination TCP/UDP port number is to be compared. noOperator(1), which is the default value, means that no comparison is to be made with the destination TCP/UDP port number. equal(2), which is …	Enumerationr/w Enumerated Values: 1 noOperator 2 equal 3 range	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.16
diffServIpAceMinDestPort If the diffServIpAceDestPortOp is range(3), this indicates the lower bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.17
diffServIpAceMaxDestPort If the diffServIpAceDestPortOp is range(3), this indicates the upper bound of the TCP/UDP port number value range. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.18
diffServIpAceDestPortBitmask If the diffServIpAceDestPortOp is equal(2), this indicates the bitmask of the diffServIpAceMinDestPort. This object may not be modified if the associated diffServIpAceType object is equal to standard(1).	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.19
diffServIpAceControlCode Indicates how the control flags of TCP packets are to be compared. diffServIpAceControlCode is AND-ed with diffServIpAceControlCodeBitmask. This object may not be modified if the associated diffServIpAceType object is e…	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.20
diffServIpAceControlCodeBitmask Indicates how the control flags of TCP packets are to be compared. It can be used to check multiple flags of the FIN, SYN, RST, PSH, ACK, URG by the sum of FIN=1, SYN=2, RST=4, PSH=8, ACK=16, URG=32. This object may not…	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.21
diffServIpAceStatus This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.17.1.22

Table for MAC ACE.

diffServMacAceEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.18.1

Entry for MAC ACE.

Indexes

diffServMacAceIndex

Column	Syntax	OID
diffServMacAceIndex An index that uniquely identifies an entry in the MAC ACE table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.1
diffServMacAceAccess Indicates the action to be taken if a packet matches this ACE.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.2
diffServMacAcePktformat Used to check the packet format of the packets. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).	Enumerationr/w Enumerated Values: 1 any 2 untagged-Eth2 3 untagged802Dot3 4 tagggedEth2 5 tagged802Dot3	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.3
diffServMacAceSourceMacAddr Indicates the 48-bit source MAC address. The specified source MAC of the packet. The packet's source MAC address is AND-ed with the value of diffServMacAceSourceMacAddrBitmask and then compared against the value of this…	TOKEN-RING-RMON-MIBMacAddressr/w Type Constraints: range: 6	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.4
diffServMacAceSourceMacAddrBitmask The specified source MAC address mask.	TOKEN-RING-RMON-MIBMacAddressr/w Type Constraints: range: 6	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.5
diffServMacAceDestMacAddr Indicates the 48-bit destination MAC address. The specified destination MAC of the packet. The packet's destination MAC address is AND-ed with the value of diffServMacAceDestMacAddrBitmask and then compared against the …	TOKEN-RING-RMON-MIBMacAddressr/w Type Constraints: range: 6	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.6
diffServMacAceDestMacAddrBitmask The specified destination MAC address mask.	TOKEN-RING-RMON-MIBMacAddressr/w Type Constraints: range: 6	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.7
diffServMacAceVidOp Indicates how a packet's VID is to be compared. This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).	Enumerationr/w Enumerated Values: 1 noOperator 2 equal 3 range	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.8
diffServMacAceMinVid Indicates the lower bound of the VID value range if the diffServMacAceVidOp is range(3).	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.9
diffServMacAceVidBitmask The bitmask of the VID if the diffServMacAceVidOp is equal(2). Default value is 0xfff.	Integer32r/w Constraints: range: 0-4095	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.10
diffServMacAceMaxVid Indicates the upper bound of the VID value range if the diffServMacAceVidOp is range(3). This object cannot be configured when the status of the entry, diffServMacAceStatus, is active(1).	Integer32r/w Constraints: range: 1-4094	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.11
diffServMacAceEtherTypeOp Indicates how a packet's ether type is to be compared.	Enumerationr/w Enumerated Values: 1 noOperator 2 equal 3 range	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.12
diffServMacAceEtherTypeBitmask The bitmask of ether type if the diffServMacAceEtherTypeOp is equal(2). The default value is 'FFFF'h.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.13
diffServMacAceMinEtherType Indicates the lower bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3).	Integer32r/w Constraints: range: 1536-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.14
diffServMacAceMaxEtherType Indicates the upper bound of the ether type value range if the diffServMacAceEtherTypeOp is range(3).	Integer32r/w Constraints: range: 1536-65535	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.15
diffServMacAceStatus This object is used to create a new row or modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.18.1.16

Table for action.

diffServActionEntry row .1.3.6.1.4.1.259.8.1.5.1.16.4.19.1

Entry for action.

Indexes

diffServActionIndex

Column	Syntax	OID
diffServActionIndex An index that uniquely identifies an entry in the action table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.1
diffServActionList The bitmap value used to identify which action capabilities are enabled on the entry. The actionPktNewPri, actionPktNewIpPrec and actionPktNewDscp can not be enabled at the same time on the entry. The actionRedPktNewDs…	Bitsr/w Enumerated Values: 0 actionPktNewPri 1 actionPktNewIpPrec 2 actionPktNewDscp 3 actionRedPktNewDscp 4 actionRedDrop	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.2
diffServActionPktNewPri Specifies the new priority value for the packet when the action is satisfied. If the actionPktNewPri bit of the diffServActionList is not enabled, this object can not be set.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.3
diffServActionPktNewIpPrec Specifies the new IP precedence facility value for the packet when the action is satisfied. If the actionPktNewIpPrec bit of the diffServActionList is not enabled, this object can not be set.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.4
diffServActionPktNewDscp Specifies the new DSCP value for the packet when the action is satisfied. If the actionPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.5
diffServActionRedPktNewDscp Specifies the new DSCP value for the red marking packet when the action is satisfied. If the actionRedPktNewDscp bit of the diffServActionList is not enabled, this object can not be set.	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.6
diffServActionRedDrop The actionRedDrop bit of the diffServActionList is for configuring this object. If the value of this object is enabled, the red marking packet will be dropped.	P-BRIDGE-MIBEnabledStatus Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.7
diffServActionStatus This object is used to create a new row, modify or delete an existing row in this table. The status column has six defined values: The status column has six defined values: - 'active', whi…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.8.1.5.1.16.4.19.1.8