ELTEX-POLICY-MIB Table View

The table of Classifier statement.

eltPolicyClassifierEntry row .1.3.6.1.4.1.35265.1.23.59.2.4.1

Classifiers can be of the ingress or post-routing phase
varieties.
Each multifield classification statement consists of the
following parameters.

Indexes

No indexes recorded

Column	Syntax	OID
eltPolicyClassifierInListVlanId1To1024 Classifier ingress VlanId List 1.	OctetStringr/w	.1.3.6.1.4.1.35265.1.23.59.2.4.1.1
eltPolicyClassifierInListVlanId1025To2048 Classifier ingress VlanId List 2.	OctetStringr/w	.1.3.6.1.4.1.35265.1.23.59.2.4.1.2
eltPolicyClassifierInListVlanId2049To3072 Classifier ingress VlanId List 3.	OctetStringr/w	.1.3.6.1.4.1.35265.1.23.59.2.4.1.3
eltPolicyClassifierInListVlanId3073To4096 Classifier ingress VlanId List 4.	OctetStringr/w	.1.3.6.1.4.1.35265.1.23.59.2.4.1.4

This table specifies The VPT to DSCP map table

eltPolicyVptDscpEntry row .1.3.6.1.4.1.35265.1.23.59.3.1.1

Each entry in this table describes The DSCP assigned to a VPT value.
The index is VPT represent by eltPolicyVptValue.

Indexes

eltPolicyVptValue

Column	Syntax	OID
eltPolicyVptValue VPT value.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.35265.1.23.59.3.1.1.1
eltPolicyDscpValue DSCP value.	Integer32r/w Constraints: range: 0-63	.1.3.6.1.4.1.35265.1.23.59.3.1.1.2
eltPolicyVptDscpStatus The status of a table entry. It is used to delete/Add an entry from this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.35265.1.23.59.3.1.1.3

Specifies The QoS trust mode for the interfaces in basic mode

eltPolicyTrustModeEntry row .1.3.6.1.4.1.35265.1.23.59.3.2.1

Specifies The QoS trust mode for the interface in basic mode

Indexes

No indexes recorded

Column	Syntax	OID
eltPolicyTrustModePortMode Defines the interface qos trust operation mode relevant for qos basic mode.	EltPolicyTrustTypesr/w Type Values: 0 none 1 cos 2 dscp 3 cos-dscp	.1.3.6.1.4.1.35265.1.23.59.3.2.1.1

This table enables the network administrator to fine-tune
the rate limit in pps given to each vlan.
The values in this table will thus override those of the
rlQosIfPolicyTable (THIS TABLE IS MANAGED FROM 3SW).

eltPolicyVlanCfgEntry row .1.3.6.1.4.1.35265.1.23.59.5.1.1

Configuration parameters for each vlan.

Indexes

No indexes recorded

Column	Syntax	OID
eltPolicyVlanCfgCirPortRateLimitPps The CIR for the port Rate limit in packets per second. CIR equal to 0 means that the rate limit does not apply to traffic in this vlan.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.35265.1.23.59.5.1.1.1
eltPolicyVlanCfgCbsPortRateLimitPackets The CBS for the port Rate Limit in packets.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.35265.1.23.59.5.1.1.2

This table defines the Metering classes for the system.

eltPolicyMeteringClassEntry row .1.3.6.1.4.1.35265.1.23.59.6.1.1

Each statement consists of the following parameters

Indexes

No indexes recorded

Column	Syntax	OID
eltPolicyMeteringClassAggregateMeterRatePps The rate in packets per second of traffic considered within the bandwidth allocated for this policy entry. Rate equal to 0 means that the rate limit does not apply to traffic.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.35265.1.23.59.6.1.1.1
eltPolicyMeteringClassAggregateMeterBurstSizePackets The Burst Size parameter for the aggregate meter leaky bucket in packets	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.35265.1.23.59.6.1.1.2

This table defines the Actions for packets that pass the meter table
ie. the characteristics that are assigned to packets before they
reach the scheduler.

eltPolicyActionEntry row .1.3.6.1.4.1.35265.1.23.59.7.2.1

Each multifield classification statement consists of the following
parameters

Indexes

No indexes recorded

Column	Syntax	OID
eltPolicyPpsActionNonDsOutProfileDropPrecedence This paramer is used at non diffserv mode to attached the drop precedence for packet OutProfile (metering), only if there is a support for drop precedence and with what level.	Enumerationr/w Enumerated Values: 1 low 2 medium 3 high 4 drop	.1.3.6.1.4.1.35265.1.23.59.7.2.1.1
eltPolicyPpsActionChangeDscpNonConform If true, the packet is re-marked with the value indicated by newDscp for non conforming packets. If false, the packet's DSCP value is not changed	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.35265.1.23.59.7.2.1.2