ECS2100-MIB Table View

Table of descriptive and status information about
the switch units in this system.

switchInfoEntry row .1.3.6.1.4.1.259.10.1.43.1.1.3.1

Table providing descriptions and status information for
switch units.

Indexes

No indexes recorded

Column	Syntax	OID
swUnitIndex This object identifies the switch within the system for which this entry contains information. This value can never be greater than switchNumber.	Integer32 Enumerated Values: 1 master 2 backupMaster 3 slave	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.1
swHardwareVer Hardware version of the main board.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.2
swMicrocodeVer Microcode version of the main board.	OctetString Constraints: range: 0-80	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.3
swLoaderVer Loader version of the main board.	OctetString Constraints: range: 0-15	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.4
swOpCodeVer Operation code version of the main board.	OctetString Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.6
swPortNumber The number of ports on this switch.	SNMPv2-SMIInteger32 Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.7
swPowerStatus Indicates the switch using internalPower(1), redundantPower(2) or both(3)	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.8
swRoleInSystem Indicates the switch is master(1), backupMaster(2) or slave(3) in this system.	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.9
swSerialNumber Serial number of the switch.	OctetString Constraints: range: 1-8	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.10
swServiceTag Service tag serial-number of the switch.	OctetString Enumerated Values: 1 internalPower 2 externalPower	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.13
swModelNumber Model number of the switch.	OctetString Enumerated Values: 1 notPresent 2 green 3 red	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.14
swEpldVer The EPLD version of the switch.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.15
swLinuxVersion The Linux Kernel version of the switch.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.1.3.1.17

Table about the status of individual powers.

switchIndivPowerEntry row .1.3.6.1.4.1.259.10.1.43.1.1.6.1

Table about the status of individual power.

Indexes

No indexes recorded

Column	Syntax	OID
swIndivPowerUnitIndex This is defined as swUnitIndex.	Integer32 Enumerated Values: 1 other 2 hundredBaseTX 3 hundredBaseFX 4 thousandBaseSX 5 thousandBaseLX 6 thousandBaseT 7 thousandBaseGBIC 8 thousandBaseSfp 9 hundredBaseFxScSingleMode 10 hundredBaseFxScMultiMode 11 thousandBaseCX 12 tenG	.1.3.6.1.4.1.259.10.1.43.1.1.6.1.1
swIndivPowerIndex 1 means internal power, 2 means external power.	Enumeration Enumerated Values: 1 reserved 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g	.1.3.6.1.4.1.259.10.1.43.1.1.6.1.2
swIndivPowerStatus notPresent(1) means not present, green(2) means up, red(3) means down.	Enumeration Enumerated Values: 1 enabled 2 disabled 5 tx 6 rx	.1.3.6.1.4.1.259.10.1.43.1.1.6.1.3

Table of descriptive and status information describing
the configuration of each switch port. This table also
contains information about each trunk.

portEntry row .1.3.6.1.4.1.259.10.1.43.1.2.1.1

An entry in the table, describing the configuration of
one switch port or trunk.

Indexes

No indexes recorded

Column	Syntax	OID
portIndex The port and the trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Enumerated Values: 1 error 2 halfDuplex10 3 fullDuplex10 4 halfDuplex100 5 fullDuplex100 6 halfDuplex1000 7 fullDuplex1000 8 halfDuplex10g 9 fullDuplex10g Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.1
portName The name of the port or trunk. This is the same as ifAlias in the IF-MIB (RFC2863 or later).	OctetStringr/w Enumerated Values: 1 error 2 backPressure 3 dot3xFlowControl 4 none	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.2
portType Indicates the port type of the configuration of the switch.	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.3
portSpeedDpxCfg Configures the speed and duplex mode for a port or trunk, according to: halfDuplex10(2) - 10Mbps and half duplex mode fullDuplex10(3) - 10Mbps and full duplex mode halfDuplex100(4) - 100Mbps and half…	Enumerationr/w Enumerated Values: 1 none 2 reserved2 3 reserved3 4 sfpForced 5 reserved5	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.4
portFlowCtrlCfg (1) Flow control mechanism is enabled with tx and rx pause mechansim. If the port type is hundredBaseTX or thousandBaseSX: When the port is operating in halfDuplex mode, the port uses backPressure flow control mechanism…	Enumerationr/w Enumerated Values: 1 master 2 slave 3 auto 4 autoPreferMaster 5 autoPreferSlave	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.5
portCapabilities Port or trunk capabilities.	Bitsr/w	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.6
portAutonegotiation Whether auto-negotiation is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.7
portSpeedDpxStatus The operating speed and duplex mode of the switched port or trunk. If the entry represents a trunk, the speed is that of its individual members unless the member ports have been inconsistently configured in which case t…	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.8
portFlowCtrlStatus (2) BackPressure flow control mechanism is used. (3) IEEE 802.3 flow control mechanism is used. (4) Flow control mechanism is disabled. If the entry represents a trunk and the member ports have been inconsistently confi…	Enumeration Enumerated Values: 0 admin 1 stpLbd 2 stpBpduGuard 3 networkAccessPortLinkDetection 4 networkAccessPortDynamicQos 5 portSec 6 lbd 7 atcBstorm 8 atcMstorm 9 udld	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.9
portTrunkIndex The trunk to which this port belongs. A value of 0 means that this port does not belong to any trunk. A value greater than zero means that this port belongs to a trunk in the trunkIndex, defined by the corresponding tru…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.10
portComboForcedMode This determines the running mode of a combo port. For a non-combo port, this variable has a value of none(1), and setting this variable to none(1) has no effect. For a combo port, this has its own valid values not equal…	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.12
portMasterSlaveModeCfg Configures the PHY mode when auto negotiation is disabled and speed-duplex is 1000full for giga copper port.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.15
portMacAddrLearningStatus Set this variable to enabled(1) to start to learn MAC addresses. Set this variable to disabled(2) to stop to learn MAC addresses.	P-BRIDGE-MIBEnabledStatusr/w Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 8 impedanceMismatch 9 failed 10 notSupported 11 noCable	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.17
portMacAddrLearningCount The current number of learned MAC addresses.	SNMPv2-SMICounter32 Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 8 impedanceMismatch 9 failed 10 notSupported 11 noCable Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.18
portUpTime The port up time (in hundredths of a second).	SNMPv2-SMITimeTicks Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 8 impedanceMismatch 9 failed 10 notSupported 11 noCable Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.19
portShutdownReason The reason of port shutdown. The value is 0 if no shutdown action is applied to this port.	Bits Enumerated Values: 1 notTestedYet 2 ok 3 open 4 short 8 impedanceMismatch 9 failed 10 notSupported 11 noCable	.1.3.6.1.4.1.259.10.1.43.1.2.1.1.20

Table for cable diagnostics result.

cableDiagResultEntry row .1.3.6.1.4.1.259.10.1.43.1.2.3.2.1

Entry for cable diagnostics result.

Indexes

No indexes recorded

Column	Syntax	OID
cableDiagResultIfIndex This is defined as the ifIndex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.1
cableDiagResultStatusPairA The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.2
cableDiagResultStatusPairB The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration Constraints: range: 0-20	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.3
cableDiagResultStatusPairC The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.4
cableDiagResultStatusPairD The result of cable diagnostics. If there is no fault on the cable, the value is ok(2). Value notTestedYet(1) means the pair is not tested yet. Value ok(2) means the pair works well. Value open(3) means there is a lack …	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.5
cableDiagResultDistancePairA Displays the fault distance of pair A of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.6
cableDiagResultDistancePairB Displays the fault distance of pair B of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.7
cableDiagResultDistancePairC Displays the fault distance of pair C of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.8
cableDiagResultDistancePairD Displays the fault distance of pair D of the cable in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.9
cableDiagResultTime Displays the last time of cable diagnostics. For example, 'Jan 1 02:03:04 2002'.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.3.2.1.11

Dispalys port utilization during recent 300 seconds.

portUtilEntry row .1.3.6.1.4.1.259.10.1.43.1.2.6.1

Dispalys port utilization during recent 300 seconds.

Indexes

No indexes recorded

Column	Syntax	OID
portUtilIfIndex The port and trunk interface of the portUtilTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.1
portInOctetRate The input octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.2
portInPacketRate The input packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Constraints: range: 1-65535	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.3
portInUtil The input utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Constraints: range: 1-31	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.4
portOutOctetRate The output octet rate (kbits/sec) of the port.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.5
portOutPacketRate The output packet rate (pkts/sec) of the port.	SNMPv2-SMICounter64 Constraints: range: 1-86400	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.6
portOutUtil The output utilization of the port, in one per hundred.	SNMPv2-SMIInteger32 Constraints: range: 1-96	.1.3.6.1.4.1.259.10.1.43.1.2.6.1.7

A list of history control entries.

portHistControlEntry row .1.3.6.1.4.1.259.10.1.43.1.2.8.1.1

A list of parameters that set up a periodic sampling of
statistics.

Indexes

No indexes recorded

Column	Syntax	OID
portHistControlIndex An index that uniquely identifies an entry in the portHistControl table.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.1
portHistControlName A textual name of the entity. It is mandatory that this only contain printable ASCII characters.	OctetStringr/w	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.2
portHistControlDataSource This object identifies the source of the data for which historical data was collected and placed in a media-specific table on behalf of this portHistControlEntry. This source can be any interface on this device.	IF-MIBInterfaceIndexr/w Constraints: range: 1-65535 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.3
portHistControlInterval The interval in seconds over which the data is sampled for each bucket in the part of the media-specific table associated with this portHistControlEntry. This interval can be set to any number of seconds between 1 and …	MinutesInteger32r/w Constraints: range: 1-2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.4
portHistControlBucketsRequested The requested number of discrete time intervals over which data is to be saved in the part of the media-specific table associated with this portHistControlEntry.	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.5
portHistControlBucketsGranted The number of discrete sampling intervals over which data shall be saved in the part of the media-specific table associated with this portHistControlEntry.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.6
portHistControlStatus The status of this portHistControl entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.259.10.1.43.1.2.8.1.1.7

A list of Ethernet history entries.

portHistCurrentEntry row .1.3.6.1.4.1.259.10.1.43.1.2.8.2.1

An historical sample of Ethernet statistics on a particular
Ethernet interface. This sample is associated with the
portHistControlEntry which set up the parameters for
a regular collection of these samples.

Indexes

No indexes recorded

Column	Syntax	OID
portHistCurrentIndex The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of portHistControlIndex.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.1
portHistCurrentSampleIndex An index that uniquely identifies the particular sample this entry represents among all samples associated with the same portHistControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.2
portHistCurrentIntervalStart The value of sysUpTime at the start of the interval over which this sample was measured.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.3
portHistCurrentInOctets The total number of octets received on the interface, including framing characters.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.4
portHistCurrentInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.5
portHistCurrentInMulticastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.6
portHistCurrentInBroadcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.7
portHistCurrentInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.8
portHistCurrentInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of in…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.9
portHistCurrentInUnknownProtos For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protoc…	SNMPv2-SMICounter64 Constraints: range: 0-10000	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.10
portHistCurrentOutOctets The total number of octets transmitted out of the interface, including framing characters.	SNMPv2-SMICounter64 Constraints: range: 0-10000	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.11
portHistCurrentOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.12
portHistCurrentOutMulticastPkts The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer prot…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.13
portHistCurrentOutBroadcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.	SNMPv2-SMICounter64 Constraints: range: 1-65535	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.14
portHistCurrentOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter64 Constraints: range: 1-2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.15
portHistCurrentOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.16
portHistCurrentInUtilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.17
portHistCurrentOutUtilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.2.1.18

A list of Ethernet history entries.

portHistPreviousEntry row .1.3.6.1.4.1.259.10.1.43.1.2.8.3.1

An historical sample of Ethernet statistics on a particular
Ethernet interface. This sample is associated with the
portHistControlEntry which set up the parameters for
a regular collection of these samples.

Indexes

No indexes recorded

Column	Syntax	OID
portHistPreviousIndex The history of which this entry is a part. The history identified by a particular value of this index is the same history as identified by the same value of portHistControlIndex.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.1
portHistPreviousSampleIndex An index that uniquely identifies the particular sample this entry represents among all samples associated with the same portHistControlEntry. This index starts at 1 and increases by one as each new sample is taken.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.2
portHistPreviousIntervalStart The value of sysUpTime at the start of the interval over which this sample was measured.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.3
portHistPreviousInOctets The total number of octets received on the interface, including framing characters.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.4
portHistPreviousInUcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were not addressed to a multicast or broadcast address at this sub-layer.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.5
portHistPreviousInMulticastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a multicast address at this sub-layer. For a MAC layer protocol, this includes both Group and Functional addresses.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.6
portHistPreviousInBroadcastPkts The number of packets, delivered by this sub-layer to a higher (sub-)layer, which were addressed to a broadcast address at this sub-layer.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.7
portHistPreviousInDiscards The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.8
portHistPreviousInErrors For packet-oriented interfaces, the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol. For character-oriented or fixed-length interfaces, the number of in…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.9
portHistPreviousInUnknownProtos For packet-oriented interfaces, the number of packets received via the interface which were discarded because of an unknown or unsupported protocol. For character-oriented or fixed-length interfaces that support protoc…	SNMPv2-SMICounter64 Constraints: range: 0-10000	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.10
portHistPreviousOutOctets The total number of octets transmitted out of the interface, including framing characters.	SNMPv2-SMICounter64 Constraints: range: 0-10000	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.11
portHistPreviousOutUcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were not addressed to a multicast or broadcast address at this sub-layer, including those that were discarded or not sent.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.12
portHistPreviousOutMulticastPkts The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a multicast address at this sub-layer, including those that were discarded or not sent. For a MAC layer prot…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.13
portHistPreviousOutBroadcastPkts The total number of packets that higher-level protocols requested be transmitted, and which were addressed to a broadcast address at this sub-layer, including those that were discarded or not sent.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.14
portHistPreviousOutDiscards The number of outbound packets which were chosen to be discarded even though no errors had been detected to prevent their being transmitted. One possible reason for discarding such a packet could be to free up buffer s…	SNMPv2-SMICounter64 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.15
portHistPreviousOutErrors For packet-oriented interfaces, the number of outbound packets that could not be transmitted because of errors. For character-oriented or fixed-length interfaces, the number of outbound transmission units that could not…	SNMPv2-SMICounter64 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.16
portHistPreviousInUtilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.17
portHistPreviousOutUtilization The best estimate of the mean physical layer network utilization on this interface during this sampling interval, in hundredths of a percent.	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.8.3.1.18

This table lists the information of the media device
(SFP/XFP/Copper) installed in the physical port.
Only the ifIndices of Ethernet ports those are associated
with the operational cards will be included in this table.

portMediaInfoEntry row .1.3.6.1.4.1.259.10.1.43.1.2.10.1

An entry in the Interface Media Information table.
The ifIndices of ethernet interfaces will be used
to index this table.

Indexes

No indexes recorded

Column	Syntax	OID
portMediaInfoIfIndex ifindex.	IF-MIBInterfaceIndex Constraints: range: 0-128 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.1
portMediaInfoConnectorType The connector type.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.2
portMediaInfoFiberType The fiber type.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.3
portMediaInfoEthComplianceCodes The ethernet compliance codes.	OctetString Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.4
portMediaInfoBaudRate The baud rate.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.5
portMediaInfoVendorOUI The OUI of the vendor.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.6
portMediaInfoVendorName The media vendor name, full name of the corporation.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.7
portMediaInfoPartNumber The media vendor part number.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.8
portMediaInfoRevision The media vendor product version number.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.9
portMediaInfoSerialNumber The vendor serial number of the media device.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.10
portMediaInfoDateCode The date code of the media device.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.259.10.1.43.1.2.10.1.11

This table lists the instrumented parameters of all
optical interfaces.

portOpticalMonitoringInfoEntry row .1.3.6.1.4.1.259.10.1.43.1.2.11.1

Only the ifIndices of optical interfaces
whose parameters need to be monitored will
be used to index this table.

Indexes

No indexes recorded

Column	Syntax	OID
portOpticalMonitoringInfoIfIndex ifindex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.1
portOpticalMonitoringInfoTemperature This object holds the value of the transmitter laser diode temperature for the interface. This object indicates the health of the transmitter. The format is xxx.yyyy C(elcius). If the device supports ALARM WARNING TRAP…	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.2
portOpticalMonitoringInfoVcc This object holds the value of the Vcc. It is measured in V. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.3
portOpticalMonitoringInfoTxBiasCurrent Tx Bias Current. It is measured in mA. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or high/low warning.	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.4
portOpticalMonitoringInfoTxPower This object holds the value of the transmitter optical signal power for the interface, measured in dBm. If the device supports ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or…	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.5
portOpticalMonitoringInfoRxPower This object holds the value of the receiver optical signal power for the interface, measured in dBm. If the device support ALARM WARNING TRAP, then followed by whether the measured value is normal, high/low alarm or hig…	OctetString	.1.3.6.1.4.1.259.10.1.43.1.2.11.1.6

This table lists the threshold of transceivers.

portTransceiverThresholdInfoEntry row .1.3.6.1.4.1.259.10.1.43.1.2.12.1

Identify the index of the transceiver

Indexes

No indexes recorded

Column	Syntax	OID
portTransceiverThresholdInfoIfIndex ifindex.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.1
portTransceiverThresholdInfoTemperatureLowAlarm This object holds the low alarm threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.2
portTransceiverThresholdInfoTemperatureLowWarn This object holds the low warning threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.3
portTransceiverThresholdInfoTemperatureHighWarn This object holds the high warning threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.4
portTransceiverThresholdInfoTemperatureHighAlarm This object holds the high alarm threshold of the transmitter laser diode temperature for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.5
portTransceiverThresholdInfoVccLowAlarm This object holds the low alarm threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.6
portTransceiverThresholdInfoVccLowWarn This object holds the low warning threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.7
portTransceiverThresholdInfoVccHighWarn This object holds the high warning threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.8
portTransceiverThresholdInfoVccHighAlarm This object holds the high alarm threshold of the Vcc.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.9
portTransceiverThresholdInfoTxBiasCurrentLowAlarm low alarm threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.10
portTransceiverThresholdInfoTxBiasCurrentLowWarn low warning threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.11
portTransceiverThresholdInfoTxBiasCurrentHighWarn high warning threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.12
portTransceiverThresholdInfoTxBiasCurrentHighAlarm high alarm threshold of Tx Bias Current.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.13
portTransceiverThresholdInfoTxPowerLowAlarm This object holds the low alarm threshold of the transmitter optical signal power for theinterface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.14
portTransceiverThresholdInfoTxPowerLowWarn This object holds the low warning threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.15
portTransceiverThresholdInfoTxPowerHighWarn This object holds the high warning threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.16
portTransceiverThresholdInfoTxPowerHighAlarm This object holds the high alarm threshold of the transmitter optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.17
portTransceiverThresholdInfoRxPowerLowAlarm This object holds the low alarm threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.18
portTransceiverThresholdInfoRxPowerLowWarn This object holds the low warning threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.19
portTransceiverThresholdInfoRxPowerHighWarn This object holds the high warning threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.20
portTransceiverThresholdInfoRxPowerHighAlarm This object holds the high alarm threshold of the receiver optical signal power for the interface.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.21
portTransceiverThresholdAutoMode Indicate the transceiver threshold is retrieved from EEPROM or configured by user.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.2.12.1.22

Table for power saving configuration.

powerSavingEntry row .1.3.6.1.4.1.259.10.1.43.1.2.14.1

An entry describing the configuration and status for
power saving.

Indexes

No indexes recorded

Column	Syntax	OID
powerSavingIfIndex The port interface of the powerSavingTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.2.14.1.1
powerSavingStatus Power saving enabled status.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.2.14.1.2

Table describing the configuration and status of each
trunk.

trunkEntry row .1.3.6.1.4.1.259.10.1.43.1.3.3.1

An entry describing the configuration and status of a
particular trunk.

Indexes

No indexes recorded

Column	Syntax	OID
trunkIndex Identifies the trunk within the switch that is described by the table entry.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.3.3.1.1
trunkPorts The complete set of ports currently associated with this trunk.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.43.1.3.3.1.2
trunkCreation A value of static(1) means a statically configured trunk. A value of lacp(2) means an LACP-configured trunk.	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.3.3.1.3
trunkStatus Writing this to valid(1) creates an entry. Writing this to invalid(2) destroys an entry. A trunk created by LACP cannot be manually destroyed or (re)configured.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.43.1.3.3.1.4

Table for LACP port configuration.

lacpPortEntry row .1.3.6.1.4.1.259.10.1.43.1.4.1.1

Entry for LACP port configuration. While an entry may
exist for a particular port, the port may not support
LACP and an attempt to enable LACP may result in
failure.

Indexes

No indexes recorded

Column	Syntax	OID
lacpPortIndex The port interface of the lacpPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.4.1.1.1
lacpPortStatus Whether 802.3ad LACP is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.4.1.1.2

The table manages port settings for Spanning Tree
Protocol 802.1d, 802.1w or 802.1s depending on the
value specified by staProtocolType.

staPortEntry row .1.3.6.1.4.1.259.10.1.43.1.5.2.1

The conceptual entry of staPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
staPortProtocolMigration When operating in RSTP (version 2) mode, writing true(1) to this object forces this port to transmit RSTP BPDUs. Any other operation on this object has no effect and it always returns false(2) when read.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.3
staPortOperEdgePort The operational value of the edge port parameter. The object is initialized to the value of staPortAdminEdgePort and is set false when a BPDU is received.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.5
staPortAdminPointToPoint The administrative point-to-point status of the LAN segment attached to this port. A value of forceTrue(0) indicates that this port should always be treated as if it is connected to a point-to-point link. A value of f…	Enumerationr/w Enumerated Values: 1 true 2 false 3 auto	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.6
staPortOperPointToPoint The operational point-to-point status of the LAN segment attached to this port. This indicates whether a port is considered to have a point-to-point connection or not. The value is determined by management or by auto-de…	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.7
staPortSystemStatus Per-port spanning tree status. (1) Spanning tree protocol is enabled. (2) Spanning tree protocol is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.9
staPortLongAdminPathCost The admin value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This obje…	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.10
staPortLongOperPathCost The oper value of the RSTP path cost or MST external pathcost. The contribution of this port to the path cost (in 32 bits value) of paths towards the spanning tree root which include this port. This objec…	Integer32 Constraints: range: 30-86400	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.11
staPortBpduFlooding This parameter is used to configure the capability of BPDUs flooding.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.12
staPortBpduGuard A value of enabled(1) indicates that BPDU port guard feature is enabled for each port. A value of disabled(2) indicates that the feature is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.15
staPortAdminEdgePortWithAuto The administrative value of the edge port parameter. A value of enable(1) indicates that this port should be assumed as an edge-port, a value of disable(2) indicates that this port should be assumed as a non-edge-port a…	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.16
staPortBpduFilter The administrative value of the BPDU filter parameter. A value of enabled(1) indicates that this port will avoid transmitting BPDUs on edge-port and the value of disabled(2) indicates that this port will not avoid trans…	P-BRIDGE-MIBEnabledStatusr/w Constraints: range: 0-4094 Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.17
staPortRootGuardStatus Specifies the desired status of the root guard. This variable configures the root guard feature to enforce the root bridge placement in the network.	P-BRIDGE-MIBEnabledStatusr/w Constraints: range: 0-61440 Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.18
staPortBpduGuardAutoRecovery A value of enabled(1) indicates that BPDU port guard auto recovery mechanism is enabled for this port. A value of disabled(2) indicates that the mechanism is disabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.19
staPortBpduGuardAutoRecoveryInterval The interval in seconds used by BPDU guard auto recovery mechanism.	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.20
staPortTcPropStop Stop topology change progate on this ifindex. Don't enable on potentially ring port.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.5.2.1.21

This table is used to configure the property of a specific
instance in Multiple Spanning Tree or Rapid Spanning Tree.
If Rapid Spanning Tree protocol is in use, the
mstInstanceEditIndex is always 0.

xstInstanceCfgEntry row .1.3.6.1.4.1.259.10.1.43.1.5.6.4.1

A conceptual row containing the property of the RST or MST instance.

Indexes

No indexes recorded

Column	Syntax	OID
xstInstanceCfgIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.1
xstInstanceCfgPriority The priority of a specific spanning tree instance. The value assigned should be in the range 0-61440 in steps of 4096.	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.2
xstInstanceCfgTimeSinceTopologyChange The time (in hundredths of a second) since the last topology change detected by the bridge entity in RST or MST.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.3
xstInstanceCfgTopChanges The total number of topology changes detected by this bridge in RST or MST since the management entity was last reset or initialized.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.4
xstInstanceCfgDesignatedRoot The bridge identifier of the root of the spanning tree as determined by the Multiple Spanning Tree Protocol. (802.1s) or Rapid Spanning Tree Protocol (802.1w) executed by this node. This value is used as the root identi…	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.5
xstInstanceCfgRootCost The cost of the path to the root as seen from this bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.6
xstInstanceCfgRootPort The number of the port which offers the lowest cost path from this bridge to the root bridge of the RST or MST.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.7
xstInstanceCfgMaxAge The maximum age of Multiple Spanning Tree Protocol (802.1s) or Rapid Spanning Tree Protocol (802.1w) information learned from the network on any port before it is discarded, in units of hundredths of a second. This is t…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.8
xstInstanceCfgHelloTime The amount of time between the transmission of configuration bridge PDUs by this node on any port when it is the root of the specific spanning tree or trying to become so, in units of hundredths of a second. This is the…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.9
xstInstanceCfgHoldTime This time value determines the interval length during which no more than two configuration bridge PDUs shall be transmitted by this node, in units of hundredths of a second.	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.10
xstInstanceCfgForwardDelay For RST or MST protocol, this time value, measured in units of hundredths of a second, controls how fast a port changes its spanning state when moving towards the forwarding state. The value determines how long the por…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.11
xstInstanceCfgBridgeMaxAge For RST or MST protocol, the time (in hundredths of second) that all bridges use for MaxAge when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to the val…	BRIDGE-MIBTimeout Constraints: range: 0-240	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.12
xstInstanceCfgBridgeHelloTime For RST or MST protocol,the time (in hundredths of a second) that all bridges use for HelloTime when this bridge is acting as the root. The granularity of this timer is specified by 802.1D-1990 to be 1 second.	BRIDGE-MIBTimeout Enumerated Values: 1 discarding 2 learning 3 forwarding	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.13
xstInstanceCfgBridgeForwardDelay For RST or MST protocol, the time (in hundredths of a second) that all bridges use for ForwardDelay when this bridge is acting as the root. Note that 802.1D-1990 specifies that the range for this parameter is related to…	BRIDGE-MIBTimeout	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.14
xstInstanceCfgTxHoldCount For RST or MST protocol, the value used by the port transmit state machine to limit the maximum transmission rate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.15
xstInstanceCfgPathCostMethod For RST or MST protocol, this indicates the type of spanning tree path cost mode used by the switch. The mode applies to all instances of the Spanning Tree protocol running on the switch. When the value o…	StaPathCostMode Type Values: 1 short 2 long	.1.3.6.1.4.1.259.10.1.43.1.5.6.4.1.16

The extension table for dot1dStpPortEntry to provide
additional Spanning Tree information and configuration.

xstInstancePortEntry row .1.3.6.1.4.1.259.10.1.43.1.5.6.5.1

The conceptual row for xstInstancePortTable.

Indexes

No indexes recorded

Column	Syntax	OID
xstInstancePortPriority Defines the priority used for this port in the Spanning Tree Algorithm. If the path cost for all ports on a switch is the same, the port with the highest priority (i.e., lowest value) will be configured as an active lin…	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.3
xstInstancePortState The port's current state as defined by application of the Spanning Tree Protocol. This state controls what action a port takes on reception of a frame: discarding(1): Port receives configuration messages, …	Enumeration Enumerated Values: 1 disabled 2 root 3 designated 4 alternate 5 backup 6 master	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.4
xstInstancePortEnable The enabled/disabled status of the port.	P-BRIDGE-MIBEnabledStatus Constraints: range: 1-200000000 Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.5
xstInstancePortDesignatedRoot The unique bridge identifier of the bridge recorded as the root in the configuration BPDUs transmitted by the designated bridge for the segment to which the port is attached.	BRIDGE-MIBBridgeId Constraints: range: 1-200000000	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.7
xstInstancePortDesignatedCost The path cost of the designated port of the segment connected to this port. This value is compared to the root path cost field in received bridge PDUs.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.8
xstInstancePortDesignatedBridge The bridge identifier of the bridge which this port considers to be the designated bridge for this port's segment.	BRIDGE-MIBBridgeId Type Constraints: range: 8	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.9
xstInstancePortDesignatedPort The port identifier of the port on the designated bridge for this port's segment.	OctetString Constraints: range: 0-4094	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.10
xstInstancePortForwardTransitions The number of times this port has transitioned from the learning state to the forwarding state.	SNMPv2-SMICounter32 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.11
xstInstancePortPortRole The role of the port in the RST or MST protocol: (1) The port has no role within the spanning tree (2) The port is part of the active topology connecting the bridge to the root bridge (i.e., root port) (3) The port …	Enumeration Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.12
xstInstancePortAdminPathCost The admin value of the MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attached to faster med…	Integer32r/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.13
xstInstancePortOperPathCost The oper value of the RST pathcost or MST internal pathcost, in the range of 1 to 200000000. This parameter is used to determine the best path between devices. Therefore, lower values should be assigned to ports attache…	Integer32 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.5.1.14

The Multiple Spanning Tree region instance vlan configuration table.
Please read the actual instance vlan mapped in the mstInstanceOperTable.

mstInstanceEditEntry row .1.3.6.1.4.1.259.10.1.43.1.5.6.6.1

A conceptual row containing the status of the MSTP instance.

Indexes

No indexes recorded

Column	Syntax	OID
mstInstanceEditIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.1
mstInstanceEditVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetStringr/w Constraints: range: 0-4094	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.2
mstInstanceEditVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.3
mstInstanceEditVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.4
mstInstanceEditVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetStringr/w Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.5
mstInstanceEditRemainingHops The remaining hop count for this MST instance.	SNMPv2-SMIInteger32 Constraints: range: 0-128	.1.3.6.1.4.1.259.10.1.43.1.5.6.6.1.6

The Multiple Spanning Tree region instance vlan mapped table.

mstInstanceOperEntry row .1.3.6.1.4.1.259.10.1.43.1.5.6.7.1

A conceptual row containing the status of the MSTP instance.

Indexes

staLoopbackDetectionPortIfIndex

Column	Syntax	OID
mstInstanceOperIndex An arbitrary integer within the range from 1 to the value of the maximum instance that uniquely identifies a spanning tree instance.	Integer32	.1.3.6.1.4.1.259.10.1.43.1.5.6.7.1.1
mstInstanceOperVlansMap A string of octets containing one bit per VLAN. The first octet corresponds to VLANs with vlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc., The most significant bit of each octet corresponds…	OctetString	.1.3.6.1.4.1.259.10.1.43.1.5.6.7.1.2
mstInstanceOperVlansMap2k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 1024 through 2047. The first octet corresponds to VLANs with vlanIndex values of 1024 through 1031; the second octet to VLANs 1032 throug…	OctetString	.1.3.6.1.4.1.259.10.1.43.1.5.6.7.1.3
mstInstanceOperVlansMap3k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 2048 through 3071. The first octet corresponds to VLANs with vlanIndex values of 2048 through 2055; the second octet to VLANs 2056 throug…	OctetString Enumerated Values: 1 auto 2 manual	.1.3.6.1.4.1.259.10.1.43.1.5.6.7.1.4
mstInstanceOperVlansMap4k A string of octets containing one bit per VLAN for VLANS with vlanIndex values of 3072 through 4095. The first octet corresponds to VLANs with vlanIndex values of 3072 through 3079; the second octet to VLANs 3080 throug…	OctetString Enumerated Values: 1 noRelease 2 release	.1.3.6.1.4.1.259.10.1.43.1.5.6.7.1.5

A table provides the mechanism to configure the
spanning tree loopback detection of each port or trunk

staLoopbackDetectionPortEntry row .1.3.6.1.4.1.259.10.1.43.1.5.8.1

A conceptual row of staLoopbackDetectionPortTable.

Indexes

No indexes recorded

Column	Syntax	OID
staLoopbackDetectionPortIfIndex The port and the trunk interfaces of the portTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.1
staLoopbackDetectionPortStatus Status of the port on whether spanning tree loopback detection is enabled.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.2
staLoopbackDetectionPortTrapStatus The parameter indicates whether the trap has to be sent when the loopback BPDUs have been detected.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.3
staLoopbackDetectionPortReleaseMode Setting it to auto(1) indicates that this port can be released from discarding state automatically after loopback has occurred. Setting it to manual(2) indicates that this port can be released from discarding state manu…	Enumerationr/w Enumerated Values: 1 rx 2 tx 3 both	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.4
staLoopbackDetectionPortRelease Set this to release(2) to release the port from discarding state. noRelease(1) will always be obtained when reading this variable.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.5
staLoopbackDetectionPortShutdownInterval Set the interval used when loopback detection action is shutdown.	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.5.8.1.7

Table for port mirroring, enabling a port to be mirrored
to/from another port. Not all ports can be mirrored and
limitations may apply as to which ports can be used as either
source or destination ports.

mirrorEntry row .1.3.6.1.4.1.259.10.1.43.1.8.1.1

The conceptual row of mirrorTable.

Indexes

No indexes recorded

Column	Syntax	OID
mirrorDestinationPort The destination port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.8.1.1.1
mirrorSourcePort The source port interface for mirrored packets. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	IF-MIBInterfaceIndex Type Constraints: range: 1..2147483647 Description: A unique value, greater than zero, for each interface or interface sub-layer in the managed system. It is recommended that values are assigned contiguously starting from 1. The value for each interface sub-layer must …	.1.3.6.1.4.1.259.10.1.43.1.8.1.1.2
mirrorType If this value is rx(1), receive packets will be mirrored. If this value is tx(2), transmit packets will be mirrored. If this value is both(3), both receive and transmit packets will be mirrored.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.8.1.1.3
mirrorStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Enumerated Values: 1 none 2 untagged 3 tagged	.1.3.6.1.4.1.259.10.1.43.1.8.1.1.4

A table that contains the settings of RSPAN.

rspanEntry row .1.3.6.1.4.1.259.10.1.43.1.8.3.1

The conceptual row of rspanTable.

Indexes

No indexes recorded

Column	Syntax	OID
rspanSessionId The session ID that may specify an entry in the table which contains destination port(s) information.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.1
rspanSrcTxPorts Specifies the source port list in tx mode.	Q-BRIDGE-MIBPortListr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.2
rspanSrcRxPorts Specifies the source port list in rx mode.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.3
rspanDstPort The port number of a destination port. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.4
rspanDstPortTag Specifies the traffic which is sent out from source port with RSPAN VLAN ID or not.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.5
rspanSwitchRole Specifies the role of current switch.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.6
rspanRemotePorts Specifies the uplink port list.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.7
rspanRemoteVlanId Specifies the ID of a RSPAN VLAN.	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.8
rspanOperStatus The operational status of the entry. A status of up(1) means the setting of a session is complete and it has started performing its function. A status of down(2) means no function is performed because of incompleted ses…	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.9
rspanStatus Set this to valid(1) to create an entry. Set this to invalid(2) to destroy an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.43.1.8.3.1.10

Table for current router ports.

igmpSnoopRouterCurrentEntry row .1.3.6.1.4.1.259.10.1.43.1.9.8.1

Entry for current router ports.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopRouterCurrentVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.8.1.1
igmpSnoopRouterCurrentPorts The set of ports which are current router ports, including static router ports. Please refer to igmpSnoopRouterStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.43.1.9.8.1.2
igmpSnoopRouterCurrentStatus The set of ports which are static router ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.43.1.9.8.1.3

Table for static router ports.

igmpSnoopRouterStaticEntry row .1.3.6.1.4.1.259.10.1.43.1.9.9.1

Entry for static router ports.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopRouterStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopRou…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.9.1.1
igmpSnoopRouterStaticPorts The set of ports which are static router ports.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.43.1.9.9.1.2
igmpSnoopRouterStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.43.1.9.9.1.3

Table for static multicast addresses.

igmpSnoopMulticastStaticEntry row .1.3.6.1.4.1.259.10.1.43.1.9.11.1

Entry for static multicast addresses.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopMulticastStaticVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.11.1.1
igmpSnoopMulticastStaticIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.43.1.9.11.1.2
igmpSnoopMulticastStaticPorts The set of ports which are members.	Q-BRIDGE-MIBPortListr/w	.1.3.6.1.4.1.259.10.1.43.1.9.11.1.3
igmpSnoopMulticastStaticStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Constraints: range: 1-255 Type Values: 1 valid 2 invalid	.1.3.6.1.4.1.259.10.1.43.1.9.11.1.4

Table for enabling or disabling IGMP snooping per VLAN.

igmpSnoopCurrentVlanEntry row .1.3.6.1.4.1.259.10.1.43.1.9.14.1

Entry for enabling or disabling IGMP snooping.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopCurrentVlanIndex Same is dot1qVlanIndex in the Q-BRIDGE-MIB. This table has only one entry - the entry for the VLAN of the management interface.	Q-BRIDGE-MIBVlanIndex Constraints: range: 2-31744	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.1
igmpSnoopCurrentVlanStatus Parameter to enable or disable IGMP snooping on this VLAN. When enabled, the device will examine IGMP packets and set up filters for IGMP ports.	P-BRIDGE-MIBEnabledStatusr/w Constraints: range: 10-31740 Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.2
igmpSnoopCurrentVlanImmediateLeave The parameter to enable or disable the Immediate-Leave feature on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Enumerated Values: 1 enabled 2 disabled 3 default	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.3
igmpSnoopCurrentVlanGeneralQuerySuppression The parameter to enable or disable the general query suppresion on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Constraints: range: 1-3 Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.4
igmpSnoopCurrentVlanLastMemQueryCount Represents the number of queries sent by the switch before it assumes there are no local members.	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.5
igmpSnoopCurrentVlanLastMemQueryIntvl The last member query interval is the max response time inserted into group-specific queries sent in response to leave group messages,and is also the the max response time inserted into group-and-source-specific query m…	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.6
igmpSnoopCurrentVlanProxyAddress Represents the address of queries sent by the switch.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.7
igmpSnoopCurrentVlanQueryIntvl Represents the query interval of queries sent by the switch.	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.8
igmpSnoopCurrentVlanQueryRespIntvl Represents the query response interval of queries sent by the switch.	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.9
igmpSnoopCurrentVlanProxyReporting Set this variable to enabled(1) to enable the feature. Set this variable to disabled(2) to disable the feature. Set this variable to default(3), the status of the feature is decided by the global configuration.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.10
igmpSnoopCurrentVlanVersion the version of igmp packets is supported by this vlan.	Unsigned32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.11
igmpSnoopCurrentVlanVersionExclusive Enable/disable control of the IGMP Snooping exclusive supported version.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.12
igmpSnoopCurrentVlanImmediateLeaveByHostIp The parameter to enable or disable the Immediate-Leave feature by host ip on this VLAN.	P-BRIDGE-MIBEnabledStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.259.10.1.43.1.9.14.1.14

Table for current multicast addresses.

igmpSnoopMulticastGroupEntry row .1.3.6.1.4.1.259.10.1.43.1.9.15.1

Entry for Group multicast addresses.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopMulticastGroupVlanIndex The interface identified by a particular value of this index is the same interface as identified by the same value of dot1qVlanIndex in the Q-BRIDGE-MIB. The entry will only appear here after a configure to igmpSnoopMul…	Q-BRIDGE-MIBVlanIndex	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.1
igmpSnoopMulticastGroupIpAddress IP address of multicast group.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.2
igmpSnoopMulticastGroupSourceIPAddress Source IP address of source.	SNMPv2-SMIIpAddress Enumerated Values: 1 permit 2 deny Type Constraints: range: 4	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.3
igmpSnoopMulticastGroupPorts The set of ports which are members of a multicast group, including static members. Please refer to igmpSnoopMulticastStaticTable.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.4
igmpSnoopMulticastGroupStatus The set of ports which are static IGMP member ports.	Q-BRIDGE-MIBPortList	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.5
igmpSnoopMulticastGroupPortCount The number of forwarding port in this group	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.15.1.6

The table for configuring the IGMP snooping profile.

igmpSnoopProfileEntry row .1.3.6.1.4.1.259.10.1.43.1.9.18.1

The entry for configuring the IGMP snooping profile.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopProfileId The ID of the IGMP snooping profile.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.18.1.1
igmpSnoopProfileAction The access mode of the IGMP snooping profile.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.9.18.1.2
igmpSnoopProfileStatus Setting this to valid(1) creates an entry. Setting this to invalid(2) destroys an entry.	ValidStatusr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.259.10.1.43.1.9.18.1.3

The table for configuring the range of the IGMP snooping
profile.

igmpSnoopProfileRangeEntry row .1.3.6.1.4.1.259.10.1.43.1.9.20.1

The entry for configuring the range of the IGMP snooping
profile.

Indexes

igmpSnoopFilterPortIndex

Column	Syntax	OID
igmpSnoopProfileRangeProfileId This is defined as igmpSnoopProfileId.	Unsigned32	.1.3.6.1.4.1.259.10.1.43.1.9.20.1.1
igmpSnoopProfileRangeInetAddressType The address type is associated with this agent. Only ipv4(1) type is supported.	INET-ADDRESS-MIBInetAddressType Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.259.10.1.43.1.9.20.1.2
igmpSnoopProfileRangeStartInetAddress The specified addresses in the start of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.10.1.43.1.9.20.1.3
igmpSnoopProfileRangeEndInetAddress The specified addresses in the end of the controlled IP multicast addresses.	INET-ADDRESS-MIBInetAddress Type Constraints: range: 0..255	.1.3.6.1.4.1.259.10.1.43.1.9.20.1.4
igmpSnoopProfileRangeAction The access mode of the IGMP snooping profile.	Enumeration	.1.3.6.1.4.1.259.10.1.43.1.9.20.1.5

Table for port configuration in IGMP filtering.

igmpSnoopFilterPortEntry row .1.3.6.1.4.1.259.10.1.43.1.9.21.1

Entry for port configuration in IGMP filtering.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopFilterPortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Constraints: range: 0-256	.1.3.6.1.4.1.259.10.1.43.1.9.21.1.1
igmpSnoopFilterPortProfileId The igmpSnoopProfileEntry identified by a particular value of this index is the same interface identified by the same value of the igmpSnoopProfileId object. If there is no corresponding entry in the igmpSnoopProfileTab…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.9.21.1.2

Table for port configuration in IGMP throttling.

igmpSnoopThrottlePortEntry row .1.3.6.1.4.1.259.10.1.43.1.9.22.1

Entry for port configuration in IGMP throttling.

Indexes

igmpSnoopPortIndex

Column	Syntax	OID
igmpSnoopThrottlePortIndex The port and trunk (including trunk members) interface of the portTable. The interface identified by a particular value of this index is the same interface identified by the same value of ifIndex in the IF-MIB.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.22.1.1
igmpSnoopThrottlePortRunningStatus Describes the running status of the IGMP throttling to the switch. A value of true(1) indicates the IGMP throttling mechanism is active. A value of false(2) indicates the IGMP throttling mechanism is inactive.	SNMPv2-TCTruthValue Enumerated Values: 1 enable 2 disable Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.9.22.1.2
igmpSnoopThrottlePortAction The action mode of the IGMP throttling. A value of replace(1) means to replace a joined multicast group randomly when an interface receives an IGMP report and the number of current joined multicast groups is equal to th…	Enumerationr/w Enumerated Values: 1 enable 2 disable	.1.3.6.1.4.1.259.10.1.43.1.9.22.1.3
igmpSnoopThrottlePortMaxGroups The maximum number of IGMP groups that the interface can join.	Integer32r/w	.1.3.6.1.4.1.259.10.1.43.1.9.22.1.4
igmpSnoopThrottlePortCurrentGroups The current number of IGMP groups that the interface has joined.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.259.10.1.43.1.9.22.1.5

Table of IGMP Snooping service per port.

igmpSnoopPortEntry row .1.3.6.1.4.1.259.10.1.43.1.9.27.1

Entry of IGMP Snooping service per port.

Indexes

No indexes recorded

Column	Syntax	OID
igmpSnoopPortIndex The port and the trunk (excluding trunk members) interface of the igmpSnoopPortTable. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex in the …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.1
igmpSnoopQueryDrop Parameter to enable or disable dropping IGMP Query packet.	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.3
igmpSnoopMulticastDataDrop Parameter to enable or disable dropping IP multicast data	Enumerationr/w	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.4
igmpSnoopPortNumGroups Current learned groups	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.5
igmpSnoopPortNumJoinSend Number of join send	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.6
igmpSnoopPortNumJoins Number of join recieved	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.7
igmpSnoopPortNumJoinSuccess Number of join group success	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.8
igmpSnoopPortNumLeavesSend Number of leave send	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.9
igmpSnoopPortNumLeaves Number of leave received	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.10
igmpSnoopPortNumGeneralQuerySend Number of general query send.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.11
igmpSnoopPortNumGeneralQueryRecevied Number of general query received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.12
igmpSnoopPortNumSepcificQuerySend Number of specific query send.	SNMPv2-SMIUnsigned32 Constraints: range: 512-512	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.13
igmpSnoopPortNumSpecificQueryReceived Number of specific query received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.14
igmpSnoopPortNumInvalidReport Number of invalid report received.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.15
igmpSnoopPortClearStatistics Clear this VLAN all statistics	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.259.10.1.43.1.9.27.1.16