DRAGONWAVE-HORIZON-IDU-MIB Table View

A table of Wireless Interface Modems

hzIduWirelessInterfaceNameEntry row .1.3.6.1.4.1.7262.2.3.5.1.1.1

A Wireless Interface Modem

Indexes

hzIduWirelessInterfaceNameIndex

Column	Syntax	OID
hzIduWirelessInterfaceNameIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.5.1.1.1.1
hzIduWirelessInterfaceNamemandatory Describes the functionality of the Wireless Interface	DisplayString	.1.3.6.1.4.1.7262.2.3.5.1.1.1.2

A table of Wireless Interface Modems

hzIduModemEntry row .1.3.6.1.4.1.7262.2.3.5.2.2.1

A Wireless Interface Modem

Indexes

hzIduModemIndex

Column	Syntax	OID
hzIduModemIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.5.2.2.1.1
hzIduModemOperStatusmandatory The current operational state of the interface. Testing indicates that no operational packets can be passed.	Enumeration Enumerated Values: 1 up 2 down 3 testing	.1.3.6.1.4.1.7262.2.3.5.2.2.1.2
hzIduModemResetmandatory Writing 1 to this object causes the modem card to be reset. All other values are not recognized. This variable always reads back as 0. mdmOperStatus should be polled by the user after this object is written to, to ve…	Integer32r/w Constraints: range: 0-1	.1.3.6.1.4.1.7262.2.3.5.2.2.1.3
hzIduModemChannelizedRSLmandatory An estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value. Once this number is divided by 10 the units are dBm. For example 352 is actually -35.2dBm	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.4
hzIduModemChannelizedRSLUnsignedIntmandatory The absolute value of the estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value. Once this number is divided by 10 the units are dBm. For example -352 is actually -35.2dBm	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.5
hzIduModemModulationTypemandatory The modulation type of the modem, distinguished according to the physical/link protocol.	Enumeration Enumerated Values: 1 qpsk 2 qam 3 qam16 4 qam32 5 qam64 6 qam128 7 qam256 8 x8psk	.1.3.6.1.4.1.7262.2.3.5.2.2.1.6
hzIduModemRxSpeedmandatory An estimate of the modem's current Rx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.7
hzIduModemTxSpeedmandatory An estimate of the modem's current Tx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.8
hzIduModemSNRmandatory SNR value in dB. Divide the value by 10 to get the actual SNR.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.9
hzIduModemEbToNoiseRatiomandatory The ratio of the modem Estimated Energy per information bit to Noise power spectral density. Divide the value by 10 to get the actual EbToNoiseRatio	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.10
hzIduModemEqualizerStressmandatory Indicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.2.2.1.11
hzIduModemSNRThresholdParametersmandatory A read-write string	DisplayStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.5.2.2.1.12
hzIduModemChannelizedRslBelowThresholdParametersmandatory A read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the seco…	DisplayStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.5.2.2.1.13

A table of Wireless Interface Modem Statistics

hzIduModemStatsEntry row .1.3.6.1.4.1.7262.2.3.5.2.3.1

Statistics for a Wireless Interface Modem

Indexes

hzIduModemStatsIndex

Column	Syntax	OID
hzIduModemStatsIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.5.2.3.1.1
hzIduModemTxBlocksmandatory The current count of Modem blocks transmitted.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.5.2.3.1.2
hzIduModemRxBlocksOKsmandatory The current count of Modem blocks received.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.5.2.3.1.3
hzIduModemRxBlocksErrorsmandatory The current count of Modem blocks received in error.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.5.2.3.1.4

A table of Wireless Interface Modems

hzIduIntermediateFrequencyCardEntry row .1.3.6.1.4.1.7262.2.3.5.3.1.1

A Wireless Interface Modem

Indexes

hzIduIFCardIndex

Column	Syntax	OID
hzIduIFCardIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.5.3.1.1.1
hzIduIFCardTxSynthesizerLockmandatory Indicates if the transmit synthesizer is locked.	Enumeration Enumerated Values: 1 unlocked 2 locked	.1.3.6.1.4.1.7262.2.3.5.3.1.1.2
hzIduIFCardRxSynthesizerLockmandatory Indicates if the receive synthesizer is locked.	Enumeration Enumerated Values: 1 unlocked 2 locked	.1.3.6.1.4.1.7262.2.3.5.3.1.1.3

A table of Wireless Interface Radios

hzIduRadioEntry row .1.3.6.1.4.1.7262.2.3.5.4.1.1

A Wireless Interface Radio

Indexes

hzIduRadioIndex

Column	Syntax	OID
hzIduRadioIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.5.4.1.1.1
hzIduRadioDescriptionmandatory A textual string containing information about the radio. Includes the manufacturer, product name, software version, serial number, and hardware version of the radio.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.4.1.1.2
hzIduRadioOperStatusmandatory The current operational state of the interface. Testing indicates that no operational packets can be passed. Testing also indicates that a firmware upgrade may be in progress	Enumeration Enumerated Values: 1 up 2 down 3 testing	.1.3.6.1.4.1.7262.2.3.5.4.1.1.3
hzIduRadioLastChangedmandatory The value of sysUpTime at the time the radio entered its current operational state. If the current state was entered prior to the last re-initialization of the local network management subsystem, then this object co…	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.5.4.1.1.4
hzIduRadioReceiveSignalLevelmandatory The Received Signal Level indicates the power of the receive level in dBm. The number is divided by 10 to get the actual dBm. For example, -432 is actually -43.2dBm.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.5
hzIduRadioReceiveSignalLevelUnsignedmandatory The Received Signal Level indicates the power of the receive level in dBm. The number is divided by -10. e.g. 432 is actually -43.2dBm. Object provided to accomodate plotting of negative RSL values which is not suppor…	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.6
hzIduRadioTxGainmandatory The gain of the radio in the transmit chain. Indicates the gain in dB.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.7
hzIduRadioRxGainmandatory The gain of the radio in the receive chain. Indicates the gain in dB.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.8
hzIduRadioResetmandatory Writing 1 to this object causes the radio to be reset. All other values are not recognized. This variable always reads back as 0. radioOperStatus should be polled by the user after this object is written to, to veri…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.9
hzIduRadioTransmitPowerdBmmandatory This defines the transmit level of the radio. If ATPC or AAM is enabled, you can't change the transmit power. The power you see is divided by 10. e.g. A display of 133 is actually 13.3 dBm. …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.10
hzIduRadioPowerOptionmandatory This indicates the power option of the radio: normal or high power.	Enumeration Enumerated Values: 1 normal 2 highPower	.1.3.6.1.4.1.7262.2.3.5.4.1.1.11
hzIduRadioTxStatemandatory This indicates the power option of the radio: normal or high power.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.5.4.1.1.12
hzIduRadioTemperaturemandatory The Radio temperature in degree Celsius. The actual temperature is determined by dividing the number by 10. e.g. 202 is actually 20.2 degrees Celsius.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.4.1.1.13
hzIduRadioRxCableLossmandatory The Rx Cable Loss in dB.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.4.1.1.14
hzIduRadioTxCableLossmandatory The Tx Cable Loss in dB.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.4.1.1.15
hzIduRadioTxCableLossChangemandatory The Tx Cable Loss Change is the difference between the configured TxPower and the measured TxPower measured in dB.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.4.1.1.16

A table of txHigh frequency settings for Radio 1

hzIduRadio1TxHighFreqEntry row .1.3.6.1.4.1.7262.2.3.5.5.1.3.1

A txHighFrequency entry containing all the frequency values

Indexes

hzIduRadio1TxHighFreqIndex

Column	Syntax	OID
hzIduRadio1TxHighFreqIndexmandatory A unique value for each frequency channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.3.1.1
hzIduRadio1TxHighFreqChannelIndexmandatory The channel index for the frequency.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.5.1.3.1.2
hzIduRadio1TxHighFreqTransmitRfFrequencymandatory The RF TX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.3.1.3
hzIduRadio1TxHighFreqReceiveRfFrequencymandatory The RF RX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.3.1.4
hzIduRadio1TxHighFreqProgrammedmandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.3.5.5.1.3.1.5

A table of txLow frequency settings for Radio 1

hzIduRadio1TxLowFreqEntry row .1.3.6.1.4.1.7262.2.3.5.5.1.4.1

A hzIduTxLowFrequeny entry containing the frequency values for a specific index

Indexes

hzIduRadio1TxLowFreqIndex

Column	Syntax	OID
hzIduRadio1TxLowFreqIndexmandatory A unique value for each frequency channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.4.1.1
hzIduRadio1TxLowFreqChannelIndexmandatory The channel index for the frequency.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.5.1.4.1.2
hzIduRadio1TxLowFreqTransmitRfFrequencymandatory The RF TX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.4.1.3
hzIduRadio1TxLowFreqReceiveRfFrequencymandatory The RF RX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.1.4.1.4
hzIduRadio1TxLowFreqProgrammedmandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.3.5.5.1.4.1.5

A table of txHigh frequency settings for Radio 2

hzIduRadio2TxHighFreqEntry row .1.3.6.1.4.1.7262.2.3.5.5.2.3.1

A txHighFrequency entry containing all the frequency values

Indexes

hzIduRadio2TxHighFreqIndex

Column	Syntax	OID
hzIduRadio2TxHighFreqIndexmandatory A unique value for each frequency channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.3.1.1
hzIduRadio2TxHighFreqChannelIndexmandatory The channel index for the frequency.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.5.2.3.1.2
hzIduRadio2TxHighFreqTransmitRfFrequencymandatory The RF TX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.3.1.3
hzIduRadio2TxHighFreqReceiveRfFrequencymandatory The RF RX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.3.1.4
hzIduRadio2TxHighFreqProgrammedmandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.3.5.5.2.3.1.5

A table of txLow frequency settings for Radio 2

hzIduRadio2TxLowFreqEntry row .1.3.6.1.4.1.7262.2.3.5.5.2.4.1

A hzIduTxLowFrequeny entry containing the frequency values for a specific index

Indexes

hzIduRadio2TxLowFreqIndex

Column	Syntax	OID
hzIduRadio2TxLowFreqIndexmandatory A unique value for each frequency channel.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.4.1.1
hzIduRadio2TxLowFreqChannelIndexmandatory The channel index for the frequency.	DisplayString	.1.3.6.1.4.1.7262.2.3.5.5.2.4.1.2
hzIduRadio2TxLowFreqTransmitRfFrequencymandatory The RF TX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.4.1.3
hzIduRadio2TxLowFreqReceiveRfFrequencymandatory The RF RX frequency in KHz.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.5.5.2.4.1.4
hzIduRadio2TxLowFreqProgrammedmandatory Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.3.5.5.2.4.1.5

A table of Modem Alarms.

hzIduModemAlarmsEntry row .1.3.6.1.4.1.7262.2.3.7.4.1.1.1

Modem Alarms

Indexes

hzIduModemAlarmsIndex

Column	Syntax	OID
hzIduModemAlarmsIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.1
hzIduModemRxLossOfSignalmandatory Loss of signal lock from the demodulator. The severity is critical, the probable cause is lost synchronization with the far end, and recommended course of action is to check the operational state of both ends of the lin…	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.2
hzIduModemRxLossOfSignalCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.3
hzIduModemTxLossOfSyncmandatory Loss of sync bytes at the input of the modulator. The severity is critical, the probable cause is physical interference in the air link, and recommended course of action is to check the line of site between the horizon …	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.4
hzIduModemTxLossOfSyncCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.5
hzIduModemSnrBelowThresholdmandatory The demodulator SNR performance worse than programmed levels. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and recom…	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.6
hzIduModemSnrBelowThresholdCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.7
hzIduModemEqualizerStressExceedThresholdmandatory Equalizer Stress measured within the demodulator exceeds the threshold value.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.8
hzIduModemEquilizerStressExceedThresholdCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.9
hzIduModemHardwareFaultmandatory	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.10
hzIduModemHardwareFaultCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.11
hzIduModemProgrammingErrormandatory Encountered some problem while programming the modem.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.12
hzIduModemProgrammingErrorCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.13
hzIduRLSShutdownActivatedmandatory RLS shutdown is activated.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.14
hzIduRLSShutdownActivatedCountsmandatory Indicates the approximate time, in seconds, that this alarm has been in the active state	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.1.1.1.15

A table of Radio Alarms.

hzIduRadioAlarmsEntry row .1.3.6.1.4.1.7262.2.3.7.4.2.1.1

Radio Alarms

Indexes

hzIduRadioAlarmsIndex

Column	Syntax	OID
hzIduRadioAlarmsIndexmandatory A unique value for each radio interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.1
hzIduRadioPLDROLostLockmandatory The PLDRO/LO has lost lock on the radio. The severity is critical, the probable cause a faulty radio unit and recommended course of action is to replace the radio unit.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.2
hzIduRadioPLDROLostLockCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.3
hzIduRadioLostCommunicationmandatory RS232 communication lost between IDU and the radio. The severity is critical, the probable cause is a faulty cable between the modem and radio, and recommended course of action is to check the connection.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.4
hzIduRadioLostCommunicationCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.5
hzIduRadioMismatchmandatory The radio connected to the IDU modem does not match the frequency programmed into the modem unit. The severity is major, the probable cause is an incorrectly programmed modem or an incorrect radio type connected to the …	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.6
hzIduRadioMismatchCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.7
hzIduRadioPowerAmpmandatory The power amplifier on the radio is not operating within normal operating specifications. The severity is critical, the probable cause a faulty radio unit, and recommended course of action is to replace the radio unit.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.8
hzIduRadioPowerAmpCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.9
hzIduRadioExcessiveTxCableLossmandatory	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.10
hzIduRadioExcessiveTxCableLossCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.11
hzIduRadioRslBelowThresholdmandatory The minimum radio receive signal level threshold has been crossed. The severity is major, the probable cause is physical interference in the air link path or misalignment of the radios or severe weather conditions, and …	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.12
hzIduRadioRslBelowThresholdCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.13
hzIduRadioHighPowerOptionM1mandatory This applies to High Power Radios only. Indicates Power Amp Alarm (M1).	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.14
hzIduRadioHighPowerOptionM1Countsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.15
hzIduRadioHighPowerOptionM2mandatory This applies to High Power Radios only. Indicates Power Amp Alarm (M2).	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.16
hzIduRadioHighPowerOptionM2Countsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.17
hzIduRadioHighPowerTxDetectormandatory This applies to High Power Radios only. Indicates minimum power threshold has not been surpassed.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.18
hzIduRadioHighPowerTxDetectorCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.19
hzIduRadioAtpcConfigMismatchmandatory The pair of the systems don't have same ATPC configurations. On one side ATPC is enabled, but on the other side ATPC is not enabled.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.20
hzIduRadioAtpcConfigMismatchCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.21
hzIduRadioRedundancySerialNumMismatchmandatory The radio serial number programmed in flash and radio do not match.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.22
hzIduRadioRedundancySerialNumMismatchCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.23
hzIduRadioExcessiveTxCableLossChangemandatory Cable loss change exceeds the threshold.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.24
hzIduRadioExcessiveTxCableLossChangeCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.25
hzIduRadioExcessiveRxCableLossmandatory Rx gain can not be adjusted to desired value.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.26
hzIduRadioExcessiveRxCableLossCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.27
hzIduRadioAtpcTxAtMaxPowermandatory ATPC auto-disabled (transmitting at coordinated power).	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.28
hzIduRadioAtpcTxAtMaxPowerCountsmandatory Indicates the approximate number of seconds that this alarm has been active.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.3.7.4.2.1.1.29

Table containing SNMP trap host entries.

hzIduSnmpTrapHostEntry row .1.3.6.1.4.1.7262.2.3.8.1.1

The snmp trap host entry containing all the trap host information

Indexes

hzIduSnmpTrapHostIndex

Column	Syntax	OID
hzIduSnmpTrapHostIndexmandatory A unique value for each trap host.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.8.1.1.1
hzIduSnmpTrapHostModemandatory Indicates how the snmp trap host is obtained for the system.	Enumeration Enumerated Values: 1 static 2 dns	.1.3.6.1.4.1.7262.2.3.8.1.1.2
hzIduSnmpTrapHostIpAddressmandatory Indicates snmp trap host IP address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.8.1.1.3
hzIduSnmpTrapHostCommunityNamemandatory The community string name used in Traps.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.8.1.1.4
hzIduSnmpTrapHostActivatedmandatory Specifies whether traps are to be sent to this specific host or not	Enumeration Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.3.8.1.1.5

Table containing snmp V3 trap host entries

hzIduSnmpV3TrapHostsEntry row .1.3.6.1.4.1.7262.2.3.8.2.1

Contains the snmp v3 trap host information

Indexes

hzIduSnmpV3TrapHostsIndex

Column	Syntax	OID
hzIduSnmpV3TrapHostsIndexmandatory A unique value for each v3 trap host.	Integer32 Constraints: range: 0-4	.1.3.6.1.4.1.7262.2.3.8.2.1.1
snmpV3TrapHostIpAddressmandatory Indicates snmp trap host IP address.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.8.2.1.2
snmpV3TrapHostUserNamemandatory The user name of the v3 trap host.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.8.2.1.3
snmpV3TrapHostAuthProtocolmandatory The authentication alogorithm used by the v3 trap host.	Enumeration Enumerated Values: 1 noAuth 2 md5 3 sha	.1.3.6.1.4.1.7262.2.3.8.2.1.4
snmpV3TrapHostAuthPasswordmandatory The authentication password of the v3 trap host.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.8.2.1.5
snmpV3TrapHostPrivProtocolmandatory The privacy encryption alogorithm used by the v3 trap host.	Enumeration Enumerated Values: 1 noPriv 2 des	.1.3.6.1.4.1.7262.2.3.8.2.1.6
snmpV3TrapHostPrivPasswordmandatory The privacy password of the v3 trap host.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.8.2.1.7
snmpV3TrapHostActivatedmandatory Specifies whether a specific v3 trap host is allowed to access the system	Enumeration Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.3.8.2.1.8

Table containing snmp manager entries

hzIduSnmpManagersEntry row .1.3.6.1.4.1.7262.2.3.9.4.1

Contains the snmp manager information

Indexes

hzIduSnmpManagersIndex

Column	Syntax	OID
hzIduSnmpManagersIndexmandatory A unique value for each manager.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.9.4.1.1
hzIduSnmpManagerIpAddressmandatory The IP address of the Manager.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.9.4.1.2
hzIduSnmpManagerCommunityNamemandatory The community string name used by the manager.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.9.4.1.3
hzIduSnmpManagerActivatedmandatory Specifies whether a specific manager is allowed to access the system	Enumeration Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.3.9.4.1.4

Table containing snmp V3 manager entries

hzIduSnmpV3ManagersEntry row .1.3.6.1.4.1.7262.2.3.9.5.1

Contains the snmp v3 manager information

Indexes

hzIduSnmpV3ManagersIndex

Column	Syntax	OID
hzIduSnmpV3ManagersIndexmandatory A unique value for each v3 manager.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.9.5.1.1
hzIduSnmpV3ManagerUserNamemandatory The user name of the v3 Manager.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.9.5.1.2
hzIduSnmpV3ManagerAuthProtocolmandatory The authentication alogorithm used by the v3 manager.	Enumeration Enumerated Values: 1 noAuth 2 md5 3 sha	.1.3.6.1.4.1.7262.2.3.9.5.1.3
hzIduSnmpV3ManagerAuthPasswordmandatory The authentication password of the v3 Manager.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.9.5.1.4
hzIduSnmpV3ManagerPrivProtocolmandatory The privacy encryption alogorithm used by the v3 manager.	Enumeration Enumerated Values: 1 noPriv 2 des	.1.3.6.1.4.1.7262.2.3.9.5.1.5
hzIduSnmpV3ManagerPrivPasswordmandatory The privacy password of the v3 Manager.	DisplayString Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.9.5.1.6
hzIduSnmpV3ManagerActivatedmandatory Specifies whether a specific v3 manager is allowed to access the system	Enumeration Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.3.9.5.1.7

A table of Wireless Interface Radios

hzIduTtySessionUserEntry row .1.3.6.1.4.1.7262.2.3.10.1.1

A Wireless Interface Radio

Indexes

hzIduTtySessionUserIndex

Column	Syntax	OID
hzIduTtySessionUserIndexmandatory A unique value for each user.	Enumeration Enumerated Values: 1 user1 2 user2 3 user3 4 user4 5 user5 6 user6	.1.3.6.1.4.1.7262.2.3.10.1.1.1
hzIduTtySessionUserNamemandatory The username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.	DisplayString Constraints: range: 0-32	.1.3.6.1.4.1.7262.2.3.10.1.1.2
hzIduTtySessionUserConnectionTypemandatory The physical port used to log in to the system. The serial port is always local to the equipment. The 10BaseT connector may be local, or remote, depending on if the configuration of network management port. The inband c…	Enumeration Enumerated Values: 1 informationNotAvailable 2 serialPort 3 enetPort2 4 enetPort1	.1.3.6.1.4.1.7262.2.3.10.1.1.3
hzIduTtySessionUserStatemandatory The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.	Enumeration Enumerated Values: 1 informationNotAvailable 2 sessionTerminated 3 sessionInProgress	.1.3.6.1.4.1.7262.2.3.10.1.1.4

A table of RLS Queue Monitor Parameters

hzIduRlsDroppedFramesThresholdEntry row .1.3.6.1.4.1.7262.2.3.13.8.1

RLS Queue Parameters

Indexes

hzIduRlsDroppedFramesThresholdIndex

Column	Syntax	OID
hzIduRlsDroppedFramesThresholdIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 queue-1 2 queue-2 3 queue-3 4 queue-4	.1.3.6.1.4.1.7262.2.3.13.8.1.1
hzIduRlsAllowedDroppedFrameRateValuemandatory Maximum allowed ethernet frame drop rate. If the average drop rate exceeds this threshold in any of the 4 queues, the Ethernet port will be shut down. This feture is availabe only with bothports option	DisplayStringr/w	.1.3.6.1.4.1.7262.2.3.13.8.1.2
hzIduRlsDroppedFrameMonitorPeriodmandatory The monitoring period in seconds.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.8.1.3

A table of RLS Soft Fault Monitor Parameters

hzIduRlsSoftFaultMonitorEntry row .1.3.6.1.4.1.7262.2.3.13.9.1

RLS Parameters for Soft Fault Monitoring

Indexes

hzIduRlsSoftFaultMonitorIndex

Column	Syntax	OID
hzIduRlsSoftFaultMonitorIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.13.9.1.1
hzIduRlsEstablishErredFrameThresholdmandatory Maximum erred blocks, per sample, allowed for link establishment.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.2
hzIduRlsShutdownErredFrameThresholdmandatory Minimum erred blocks, per sample, allowed before link shutdown.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.3
hzIduRlsEstablishNumberOfSamplesmandatory Minimum number of consecutive good samples required before link is established.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.4
hzIduRlsShutdownNumberOfSamplesmandatory Minimum number of consecutive erred samples before link is shutdown.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.5
hzIduRlsEstablishSamplePeriodmandatory Period of Time, in milliseconds, for monitoring Establish Erred Frame Threshold.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.6
hzIduRlsShutdownSamplePeriodmandatory Period of Time, in milliseconds, for monitoring Shutdown Erred Frame Threshold.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.7
hzIduRlsQuickShutdownSamplePeriodmandatory Minimum number of milliseconds required to classify samples as erred.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.9.1.8

A table of RLS Hard Fault Monitor Parameters

hzIduHardFaultMonitorEntry row .1.3.6.1.4.1.7262.2.3.13.10.1

RLS Parameters for Hard Fault Monitoring

Indexes

hzIduHardFaultMonitorIndex

Column	Syntax	OID
hzIduHardFaultMonitorIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.13.10.1.1
hzIduRlsHardFaultSamplePeriodmandatory The period of time, in milliseconds, for which the rlsFaultThreshold is applied.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.10.1.2
hzIduRlsHardFaultThresholdmandatory Acceptalbe errored block rate in percent	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.10.1.3

A table of RLS RSL Monitor Parameters

hzIduRlsReceiveSignalLevelMonitorEntry row .1.3.6.1.4.1.7262.2.3.13.11.1

RLS RSL Monitor Parameters

Indexes

hzIduRlsReceiveSignalLevelMonitorIndex

Column	Syntax	OID
hzIduRlsReceiveSignalLevelMonitorIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.13.11.1.1
hzIduRlsMakeRslMonitorRslValuemandatory The RSL threshold, in dBm. When Link is inactive and if RSL is higher than this threshold for a desired period, the link will become active.	DisplayStringr/w Constraints: range: 0-24	.1.3.6.1.4.1.7262.2.3.13.11.1.2
hzIduRlsMakeRslMonitorPeriodmandatory The desired period, in seconds. When Link is inactive and if RSL is higher than the desired threshold for this period, the link will become active.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.11.1.3

A table of RLS Currently Observed Queue Monitor Parameters

hzIduRlsCurrentDroppedFramesEntry row .1.3.6.1.4.1.7262.2.3.13.12.1.1

RLS Currently Observed Queue Monitor Parameters

Indexes

hzIduRlsCurrentDroppedFramesIndex

Column	Syntax	OID
hzIduRlsCurrentDroppedFramesIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 queue-1 2 queue-2 3 queue-3 4 queue-4	.1.3.6.1.4.1.7262.2.3.13.12.1.1.1
hzIduRlsCurrentDroppedFramesRateValuemandatory RLS Current Ethernet Frame drop rate	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.1.1.2
hzIduRlsCurrentDroppedFrameMonitorPeriodmandatory Queue Monitoring time	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.12.1.1.3
hzIduRlsCurrentQueueStatusmandatory Queue Status - OK: drop rate is within the threshold, Activated: Exceeded the drop threshold	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.1.1.4

A table of RLS Parameters and states

hzIduRlsStatusEntry row .1.3.6.1.4.1.7262.2.3.13.12.2.1

RLS Parameters and states

Indexes

hzIduRlsStatusIndex

Column	Syntax	OID
hzIduRlsStatusIndexmandatory A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.3.13.12.2.1.1
hzIduRlsOptionmandatory RLS Option. On Basic: RLS enabled with base degrade monitoring; On Advanced: RLS enabled with hard fault monitoring; On Anyport: If any one of the wireless links exceeds the threshold Ehternet Port will be shut down On …	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.2
hzIduRlsStatemandatory Rapid Link Shutdown State. If the state is activated, that means The wireless link is down for Ethernet traffic; If the state is inactivated, that means that wireless link is up for Ethernet traffic.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.3
hzIduRlsMismatchStatemandatory RLS Mismatch State. If the state is activated, that means RLS configuration is mismatched with peer. If the state is OK, that means RLS configuration is matched with peer.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.4
hzIduDegradeMonitorStatemandatory Degrade Monitor State. If the state is activated, that means the RLS Degrade Monitor is asserting the link down. If the state is OK, that means the RLS Degrade Monitor is asserting the link up.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.5
hzIduHardFaultMonitorStatemandatory Hard Fault Monitor State. If the state is activated, that means the Hard Fault Monitor is asserting the link down. If the state is OK, that means the RLS Hard Fault Monitor is asserting the link up.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.6
hzIduMakeRslThresholdStatemandatory Make RSL Threshold State. If the state is not met, that means the RLS signal level is below the threshold value. If the state is OK, that means the RLS signal level is above the threshold value.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.7
hzIduPeerRlsStatemandatory Peer RLS State. If the state is activated, that means the peer has activated RLS. If the state is OK, that means the Peer hasn't activated RLS.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.8
hzIduRadioInterfaceStatemandatory Radio Interface State. If the state is down, that means The radio interface is not operational(muted,disconnected, not configured). If the state is up, that means the radio interface is operational.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.9
hzIduNetworkInterfaceStatemandatory Network Interface State. If the state is down, that means the network interface (Ethernet/PHY) is not operational(disconnected, not configured). If the state is up, that means the network interface (Ethernet/PHY) is o…	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.10
hzIduUserConfiguredEstablishFermandatory User Configured Establish Frame Error Ratio required for the link to be restored to service, set by the user. An example value being '1.0E-7'.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.11
hzIduMinimumAchievableEstablishFermandatory Minimum achievable Frame Error Ratio required for the link to be restored to service. An example value being '1.0E-7'.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.12
hzIduUserConfiguredShutdownFermandatory User Configured Shutdown Frame Error Ratio required for the link to remain in-service, set by the user. An example value being '1.0E-7'.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.13
hzIduMinimumAchievableShutdownFermandatory Minimum achievable Frame Error Ratio required for the link to remain in-service. An example value being '1.0E-7'.	DisplayString	.1.3.6.1.4.1.7262.2.3.13.12.2.1.14
hzIduUserConfiguredEstablishMonitorTimemandatory User Configured Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, set by user	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.12.2.1.15
hzIduActualEstablishMonitorTimemandatory Actual Establish Monitor Time, in milliseconds, for which the 'User Configured Establish FER' must be achieved to bring link into service, it's a multiple of the establish sample period required to observe the FER	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.12.2.1.16
hzIduUserConfiguredShutdownMonitorTimemandatory User Configured Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, set by user.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.12.2.1.17
hzIduActualShutdownMonitorTimemandatory Actual Shutdown Monitor Time, in milliseconds, for which the 'User Configured Shutdown FER' must be met for the link to remain in-service, it's a multiple of the shutdown sample period required to observe the FER	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.13.12.2.1.18

Table containing sntp server entries

hzIduSntpServerEntry row .1.3.6.1.4.1.7262.2.3.14.3.1

Contains the sntp server information

Indexes

hzIduSntpServerIndex

Column	Syntax	OID
hzIduSntpServerIndexmandatory A unique value for each server.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.14.3.1.1
hzIduSntpServerIpAddressmandatory The IP address of the server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.14.3.1.2
hzIduSntpServerStatusmandatory The status of the sntp server.	Enumeration Enumerated Values: 1 good 2 failed	.1.3.6.1.4.1.7262.2.3.14.3.1.3
hzIduSntpServerStratummandatory Specifies the stratum of a server, 0 for failed server	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.14.3.1.4

Table containing radius server entries

hzIduRadiusServerEntry row .1.3.6.1.4.1.7262.2.3.16.5.1

Contains the sntp server information

Indexes

hzIduRadiusServerIndex

Column	Syntax	OID
hzIduRadiusServerIndexmandatory A unique value for each server.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.3.16.5.1.1
hzIduRadiusCfgdHostIpAddressmandatory The IP address of the configured radius server.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.16.5.1.2
hzIduRadiusActiveHostIpAddressmandatory The IP address of the active radius server.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.7262.2.3.16.5.1.3