DRAGONWAVE-HCP-MIB Table View

Table contains the software inventory.

hzCpSwInventoryEntry row .1.3.6.1.4.1.7262.2.5.1.3.2.1.1

Software inventory entry.

Indexes

hzCpSwInvBank

Column	Syntax	OID
hzCpSwInvBank Software bank in the flash.	Enumeration Enumerated Values: 1 bank-A 2 bank-B	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.1
hzCpSwInvStatus Software bank status.	Enumeration Enumerated Values: 1 active 2 standby	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.2
hzCpSwInvOmniRelease The version number of the Omni.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.3
hzCpSwInvFrequencyFileVersion The version number of the frequency file.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.4
hzCpSwInvMibVersion The version number of the system MIB.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.5
hzCpSwInvBootloaderVersion The version number of the bootloader.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.3.2.1.1.6

A table of Wireless Interface Modems

hzCpHitlessAamModemEntry row .1.3.6.1.4.1.7262.2.5.1.6.2.1.1

A Wireless Interface Modem

Indexes

hzCpHitlessAamModemIndex

Column	Syntax	OID
hzCpHitlessAamModemIndex A unique value for each interface.	Enumeration Enumerated Values: 1 modem-1	.1.3.6.1.4.1.7262.2.5.1.6.2.1.1.1
hzCpHitlessAamModemDiagnose This service effecting object accepts either 'up' or 'down' to diagnose whether the modulation speed can be increased or decreased respectively for modem. Poll the hzCpHitlessAamModemDiagnosticResult object to determine…	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.7262.2.5.1.6.2.1.1.2
hzCpHitlessAamModemDiagnosticResult The result from Hitless AAM Diagnostic is read from this object.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.6.2.1.1.3

A table of system upgrade feature groups.

hzCpSysUpgradeFeatureGroupsEntry row .1.3.6.1.4.1.7262.2.5.1.7.1.1

A system upgrade feature group entry containing all licensed feature groups.

Indexes

hzCpUpgradeLicensedFeatureIndex

Column	Syntax	OID
hzCpUpgradeLicensedFeatureIndex A unique value for each licensed group.	Enumeration Enumerated Values: 1 rls 2 eoamEcfmLldp 3 hitlessAam 4 bac 5 encryption	.1.3.6.1.4.1.7262.2.5.1.7.1.1.1
hzCpUpgradeLicensedFeatureKey The key required for upgrading a feature.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.7.1.1.2
hzCpUpgradeLicensedFeatureCount This object indicates the number of times the licensed feature has been changed successfully.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.7.1.1.3

A table of system downgrade system groups.

hzCpSysDowngradeFeatureGroupsEntry row .1.3.6.1.4.1.7262.2.5.1.7.2.1

A system downgrade feature group entry containing all licensed feature groups.

Indexes

hzCpDowngradeLicensedFeatureIndex

Column	Syntax	OID
hzCpDowngradeLicensedFeatureIndex A unique value for each licensed group.	Enumeration Enumerated Values: 1 rls 2 eoamEcfmLldp 3 hitlessAam 4 bac 5 encryption	.1.3.6.1.4.1.7262.2.5.1.7.2.1.1
hzCpDowngradeLicensedFeature Downgrading a licensed feature.	Enumerationr/w Enumerated Values: 1 downgrade	.1.3.6.1.4.1.7262.2.5.1.7.2.1.2
hzCpDowngradeLicensedFeatureCount This object indicates the number of times the licensed feature has been downgraded.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.7.2.1.3
hzCpDowngradeLicensedFeatureKey The key generated after downgrading a licensed feature.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.7.2.1.4

A table of licensed feature groups.

hzCpSysLicensedFeatureGroupsEntry row .1.3.6.1.4.1.7262.2.5.1.7.3.1

A system feature group entry containing all licensed feature groups.

Indexes

hzCpSysLicensedFeatureGroupIndex

Column	Syntax	OID
hzCpSysLicensedFeatureGroupIndex A unique value for each licensed group.	Enumeration Enumerated Values: 1 rls 2 eoamEcfmLldp 3 hitlessAam 4 bac 5 encryption	.1.3.6.1.4.1.7262.2.5.1.7.3.1.1
hzCpSysLicensedFeatureGroup The name of the licensed feature group.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.7.3.1.2
hzCpSysLicensedFeatureGroupStatus Specifies whether the feature group is unlicensed or licensed.	Enumeration Enumerated Values: 1 unlicensed 2 licensed	.1.3.6.1.4.1.7262.2.5.1.7.3.1.3

Table containing SNTP server entries

hzCpSntpServerEntry row .1.3.6.1.4.1.7262.2.5.1.10.4.1

Contains the SNTP server information

Indexes

hzCpSntpServerIndex

Column	Syntax	OID
hzCpSntpServerIndex A unique value for each server.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.10.4.1.1
hzCpSntpServerDomain Indicates SNTP server inet address type. Valid types are ipv4 or ipv6.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7262.2.5.1.10.4.1.2
hzCpSntpServerAddress Indicates SNTP server inet address octet string.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7262.2.5.1.10.4.1.3
hzCpSntpServerStatus The status of the SNTP server.	Enumeration Enumerated Values: 1 good 2 failed	.1.3.6.1.4.1.7262.2.5.1.10.4.1.4
hzCpSntpServerStratum Specifies the stratum of a server, 0 for failed server	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.10.4.1.5

Table containing BAC entries

hzCpBacEntry row .1.3.6.1.4.1.7262.2.5.1.12.2.1

Contains the BAC information for all queues

Indexes

hzCpBacQIndex

Column	Syntax	OID
hzCpBacQIndex A unique value for each of the 8 Queues.	Enumeration Enumerated Values: 1 q1 2 q2 3 q3 4 q4 5 q5 6 q6 7 q7 8 q8	.1.3.6.1.4.1.7262.2.5.1.12.2.1.1
hzCpBacQEnable Configure queue compression state to disable/enable.	Enumerationr/w Enumerated Values: 1 disabled 2 enabled	.1.3.6.1.4.1.7262.2.5.1.12.2.1.2
hzCpBacQBlockSize Configure queue compression block size (256...8000). Block size has to be in increments of 64 bytes. Otherwise it will be rounded off to nearest 64 bytes. Valid block sizes are <256 512 1024 4032 8000>	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.12.2.1.3
hzCpBacRecordLogging Enables/disables logging of BAC related statistics like Maximum BAC gain and Maximum uncompressed ratio on a per queue basis to syslog and flashlog.	Enumerationr/w Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.5.1.12.2.1.4
hzCpBacUncompressedRatio Running average Uncompressed ratio is calculated by collecting n samples of bytes uncompressed and bytes in data over specified average period in percentage.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.12.2.1.5
hzCpBacGain The Running Average BAC gain is the sum of all bytes getting into the compressor divided by the sum of all bytes compressed and bytes uncompressed calculated over an average period.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.1.12.2.1.6

Performance Monitoring table for Radio Synchronous Physical Interface thresholds.

hzCpPmRspiThresholdEntry row .1.3.6.1.4.1.7262.2.5.1.14.1.1

Contains information for Radio Synchronous Physical Interface thresholds.

Indexes

hzCpPmRspiThrIndex

Column	Syntax	OID
hzCpPmRspiThrIndex Index to PM RSPI Threshold table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.1
hzCpPmRLT1 Receive Level Threshold 1, represents the number of seconds below the first threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.2
hzCpPmRLT2 Receive Level Threshold 2, represents the number of seconds below the second threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.3
hzCpPmRLT3 Receive Level Threshold 3, represents the number of seconds below the third threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.4
hzCpPmRLT4 Receive Level Threshold 4, represents the number of seconds below the fourth threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.5
hzCpPmTLT1 Transmit Level Threshold 1, represents the number of seconds below the first threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.6
hzCpPmTLT2 Transmit Level Threshold 2, represents the number of seconds below the second threshold.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.1.1.7
hzCpPmRspiThrRowStatus This object is used for applying all RSPI thresholds simultaneously.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7262.2.5.1.14.1.1.8

Performance Monitoring table for Capacity thresholds.

hzCpPmAdvThresholdEntry row .1.3.6.1.4.1.7262.2.5.1.14.2.1

Contains information for Capacity thresholds.

Indexes

hzCpPmAdvThrIndex

Column	Syntax	OID
hzCpPmAdvThrIndex Index to PM Capacity Threshold table.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.2.1.1
hzCpPmAdvTxHitsT1 Transmit Hits Threshold 1.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.2.1.2
hzCpPmAdvRxHitsT1 Receive Hits Threshold 1.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.1.14.2.1.3
hzCpPmAdvRowStatus This object is used for applying all Capacity thresholds simultaneously.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.7262.2.5.1.14.2.1.4

Table containing snmp V3 manager entries

hzCpSnmpV3ManagersEntry row .1.3.6.1.4.1.7262.2.5.2.5.5.1

Contains the snmp v3 manager information

Indexes

hzCpSnmpV3ManagersIndex

Column	Syntax	OID
hzCpSnmpV3ManagersIndex A unique value for each v3 manager.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.2.5.5.1.1
hzCpSnmpV3ManagerUserName The user name of the v3 Manager.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.5.5.1.2
hzCpSnmpV3ManagerAuthProtocol The authentication alogorithm used by the v3 manager.	Enumerationr/w Enumerated Values: 1 noAuth 2 md5 3 sha	.1.3.6.1.4.1.7262.2.5.2.5.5.1.3
hzCpSnmpV3ManagerAuthPassword The authentication password of the v3 Manager.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.5.5.1.4
hzCpSnmpV3ManagerPrivProtocol The privacy encryption alogorithm used by the v3 manager.	Enumerationr/w Enumerated Values: 1 noPriv 2 des	.1.3.6.1.4.1.7262.2.5.2.5.5.1.5
hzCpSnmpV3ManagerPrivPassword The privacy password of the v3 Manager.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.5.5.1.6
hzCpSnmpV3ManagerActivated Specifies whether a specific v3 manager is allowed to access the system	Enumerationr/w Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.5.2.5.5.1.7

Table containing snmp manager entries

hzCpSnmpManagersEntry row .1.3.6.1.4.1.7262.2.5.2.5.7.1

Contains the snmp manager information

Indexes

hzCpSnmpManagersIndex

Column	Syntax	OID
hzCpSnmpManagersIndex A unique value for each manager.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.2.5.7.1.1
hzCpSnmpManagerDomain Indicates snmp manager inet address type. Valid types are ipv4 or ipv6.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7262.2.5.2.5.7.1.2
hzCpSnmpManagerAddress Indicates snmp manager inet address octet string.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7262.2.5.2.5.7.1.3
hzCpSnmpManagerCommunityName The community string name used by the manager.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.5.7.1.4
hzCpSnmpManagersPrefixLength The Ip Address prefix length. The valid range for IPV4 Address is 1-32 and for IPV6 is 1-128.	INET-ADDRESS-MIBInetAddressPrefixLengthr/w Type Constraints: range: 0..2040	.1.3.6.1.4.1.7262.2.5.2.5.7.1.5
hzCpSnmpManagerActivated Specifies whether a specific manager is allowed to access the system. This object deprecates hzCpSnmpManagerActivatedDep.	Enumerationr/w Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.5.2.5.7.1.32

Table containing SNMP trap host entries.

hzCpSnmpTrapHostEntry row .1.3.6.1.4.1.7262.2.5.2.6.4.1

The snmp trap host entry containing all the trap host information

Indexes

hzCpSnmpTrapHostIndex

Column	Syntax	OID
hzCpSnmpTrapHostIndex A unique value for each trap host.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.2.6.4.1.1
hzCpSnmpTrapHostDomain Indicates snmp trap host inet address type. Valid types are ipv4 or ipv6.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7262.2.5.2.6.4.1.2
hzCpSnmpTrapHostAddress Indicates snmp trap host inet address octet string. This object deprecates hzCpSnmpTrapHostIpAddressDep.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7262.2.5.2.6.4.1.3
hzCpSnmpTrapHostCommunityName The community string name used in Traps.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.6.4.1.4
hzCpSnmpTrapHostActivated Specifies whether traps are to be sent to this specific host or not. This object deprecates hzCpSnmpTrapHostActivatedDep.	Enumerationr/w Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.5.2.6.4.1.32

Table containing snmp V3 trap host entries

hzCpSnmpV3TrapHostsEntry row .1.3.6.1.4.1.7262.2.5.2.6.5.1

Contains the snmp v3 trap host information

Indexes

hzCpSnmpV3TrapHostsIndex

Column	Syntax	OID
hzCpSnmpV3TrapHostsIndex A unique value for each v3 trap host.	Integer32 Constraints: range: 0-4	.1.3.6.1.4.1.7262.2.5.2.6.5.1.1
hzCpSnmpV3TrapHostDomain Indicates v3 trap host inet address type. Valid types are ipv4 or ipv6.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7262.2.5.2.6.5.1.2
hzCpSnmpV3TrapHostAddress Indicates snmp v3 trap host inet address octet string. This object deprecates hzCpSnmpV3TrapHostIpAddressDep.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7262.2.5.2.6.5.1.3
hzCpSnmpV3TrapHostUserName The user name of the v3 trap host.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.6.5.1.4
hzCpSnmpV3TrapHostAuthProtocol The authentication alogorithm used by the v3 trap host.	Enumerationr/w Enumerated Values: 1 noAuth 2 md5 3 sha	.1.3.6.1.4.1.7262.2.5.2.6.5.1.5
hzCpSnmpV3TrapHostAuthPassword The authentication password of the v3 trap host.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.6.5.1.6
hzCpSnmpV3TrapHostPrivProtocol The privacy encryption alogorithm used by the v3 trap host.	Enumerationr/w Enumerated Values: 1 noPriv 2 des	.1.3.6.1.4.1.7262.2.5.2.6.5.1.7
hzCpSnmpV3TrapHostPrivPassword The privacy password of the v3 trap host.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.6.5.1.8
hzCpSnmpV3TrapHostActivated Specifies whether v3 traps are to be sent to this specific host or not. This object deprecates hzCpSnmpV3TrapHostActivatedDep.	Enumerationr/w Enumerated Values: 1 notActive 2 active	.1.3.6.1.4.1.7262.2.5.2.6.5.1.32

Table containing radius server entries

hzCpRadiusServerEntry row .1.3.6.1.4.1.7262.2.5.2.7.6.1

Contains the SNTP server information

Indexes

hzCpRadiusServerIndex

Column	Syntax	OID
hzCpRadiusServerIndex A unique value for each radius server.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.2.7.6.1.1
hzCpRadiusCfgdHostDomain Indicates configured radius radius inet address type. Valid types are ipv4 or ipv6.	INET-ADDRESS-MIBInetAddressTyper/w Type Values: 0 unknown 1 ipv4 2 ipv6 3 ipv4z 4 ipv6z 16 dns 25 l2vpn	.1.3.6.1.4.1.7262.2.5.2.7.6.1.2
hzCpRadiusCfgdHostAddress Indicates configured radius server inet address octet string. This object deprecates hzCpRadiusCfgdHostIpAddressDep.	INET-ADDRESS-MIBInetAddressr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.7262.2.5.2.7.6.1.3
hzCpRadiusCfgdHostKey The key of the configured radius server.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.7.6.1.4

A table of user sessions

hzCpUserSessionUserEntry row .1.3.6.1.4.1.7262.2.5.2.8.1.1

User session entry

Indexes

hzCpUserSessionUserIndex

Column	Syntax	OID
hzCpUserSessionUserIndex A unique value for each user.	Enumeration Enumerated Values: 1 user1 2 user2 3 user3 4 user4 5 user5 6 user6 7 user7 8 user8 9 user9 10 user10 11 user11 12 user12 13 user13 14 user14 15 user15 16 user16 17 user17 18 user18 19 user19 20 user20	.1.3.6.1.4.1.7262.2.5.2.8.1.1.1
hzCpUserSessionUserName The username of a management session using Telnet or HTTP. The session state variable must be checked to determine if the management session is currently in progress.	SNMPv2-TCDisplayString Constraints: range: 0-32 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.8.1.1.2
hzCpUserSessionUserConnectionType Either telnet, ssh, http or https. Ethernet connection may be through any physical port(s) dedicated to management of the equipment.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.2.8.1.1.3
hzCpUserSessionUserState The state of the session. The session is inProgress if the user is currently logged into the system. The session is terminated if the user has logged out of the system.	Enumeration Enumerated Values: 1 informationNotAvailable 2 sessionTerminated 3 sessionInProgress	.1.3.6.1.4.1.7262.2.5.2.8.1.1.4

A table for enet port configuration

hzCpEnetPortConfigEntry row .1.3.6.1.4.1.7262.2.5.3.1.1.1

An entry for enet port configuration

Indexes

hzCpEnetPortIndex

Column	Syntax	OID
hzCpEnetPortIndex A unique value for each enet port.	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.3.1.1.1.1
hzCpEnetPortName Describes the port interface name	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.3.1.1.1.2
hzCpEnetPortAutoNegotiation Turns auto-negotiation on or off for Ethernet Port. Turning off results in the interface defaulting to 100BaseT, Full Duplex.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.7262.2.5.3.1.1.1.3
hzCpEnetPortSpeed Configure the port interface speed .	Enumerationr/w Enumerated Values: 1 x10M 2 x100M 3 x1000M 4 auto	.1.3.6.1.4.1.7262.2.5.3.1.1.1.4
hzCpEnetPortDuplex Configure the port interface duplex.	Enumeration Enumerated Values: 1 full 2 half 3 auto	.1.3.6.1.4.1.7262.2.5.3.1.1.1.5
hzCpEnetPortMedia Configure the port interface media type.	Enumerationr/w Enumerated Values: 1 copper 2 fiber 3 auto	.1.3.6.1.4.1.7262.2.5.3.1.1.1.6
hzCpEnetPortAdminState Enable or disable the admin status of the port.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.7262.2.5.3.1.1.1.7
hzCpEnetPortPauseFrame When PAUSE is enabled, port pause frames can be generated by the system and the pause frames will flow toward the link partner on the network. When PAUSE is not enabled, no pause frames will be generated by the system.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.7262.2.5.3.1.1.1.8
hzCpEnetPortMaxFrameSize For port the default maximum frame size is 1600 bytes. The settable maximum frame size must be a multiple of 128. If the chosen maximum frame size is not a multiple of 128, its closest number which is a multiple of 12…	Integer32r/w Constraints: range: 1600-9600	.1.3.6.1.4.1.7262.2.5.3.1.1.1.9
hzCpEnetPortOpticalTransceiverState When it is on, optical transmitter for port1 is enabled. Otherwise optical transmitter is disabled. This option is valid for port1 only if media type is configured as fiber.	Enumerationr/w Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.5.3.1.1.1.10
hzCpEnetPortState Enables or disables enet-port3 or enet-port4.	Enumerationr/w Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.7262.2.5.3.1.1.1.11
hzCpEnetPayloadState Enables or disables payload on a specific port. If payload state is disabled for that port, it's considered as purely management.	Enumerationr/w Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.7262.2.5.3.1.1.1.12

A table for enet port status

hzCpEnetPortStatusEntry row .1.3.6.1.4.1.7262.2.5.3.1.2.1

An entry for enet port status

Indexes

hzCpEnetPortStatusIndex

Column	Syntax	OID
hzCpEnetPortStatusIndex A unique value for each enet port.	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.3.1.2.1.1
hzCpEnetPortLinkStatus Indicates the port link status.	Enumeration Enumerated Values: 1 down 2 up 3 invalid	.1.3.6.1.4.1.7262.2.5.3.1.2.1.2
hzCpEnetPortAutoNegotiationStatus Indicates the port AutoNegotiation status.	Enumeration Enumerated Values: 1 on 2 off 3 invalid	.1.3.6.1.4.1.7262.2.5.3.1.2.1.3
hzCpEnetPortSpeedStatus Indicates the port interface speed status.	Enumeration Enumerated Values: 1 x10M 2 x100M 3 x1000M 4 auto 5 invalid	.1.3.6.1.4.1.7262.2.5.3.1.2.1.4
hzCpEnetPortDuplexStatus Indicates the port interface duplex status.	Enumeration Enumerated Values: 1 full 2 half 3 auto 4 invalid	.1.3.6.1.4.1.7262.2.5.3.1.2.1.5
hzCpEnetPortMediaStatus Indicates the port interface media status.	Enumeration Enumerated Values: 1 copper 2 fiber 3 auto 4 invalid	.1.3.6.1.4.1.7262.2.5.3.1.2.1.6

A table for enet port stats

hzCpEnetPortStatsEntry row .1.3.6.1.4.1.7262.2.5.3.1.3.1

An entry for enet port stats

Indexes

hzCpEnetPortStatsIndex

Column	Syntax	OID
hzCpEnetPortStatsIndex A unique value for each enet port.	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.3.1.3.1.1
hzCpEnetPortTxFrames The total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.2
hzCpEnetPortTxBytes The total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those that were discarded or not sent.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.3
hzCpEnetPortRxFramesOk The total number of bytes received on the interface, including framing characters.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.4
hzCpEnetPortRxBytesOk The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.5
hzCpEnetPortRxFramesLengthErrors The number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.6
hzCpEnetPortRxFramesCrcErrors The number of packets received via the interface which were discarded because of rx frames CRC errors.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.7
hzCpEnetPortRxDiscarded The number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One possible reason for discarding such a packet co…	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.3.1.8

A table of enet aggregate frames.

hzCpEnetAggFramesInQueueEntry row .1.3.6.1.4.1.7262.2.5.3.1.4.11.1

An entry of enet aggregate frames.

Indexes

hzCpEnetAggFramesInQueueIndex

Column	Syntax	OID
hzCpEnetAggFramesInQueueIndex A unique value for each of the 8 queues.	Enumeration Enumerated Values: 1 q1 2 q2 3 q3 4 q4 5 q5 6 q6 7 q7 8 q8	.1.3.6.1.4.1.7262.2.5.3.1.4.11.1.1
hzCpEnetAggFramesInQueue The current count of frames in queues.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.4.11.1.2
hzCpEnetAggFramesInQueueDiscarded The current count of frames received in queues that were discarded due to an error. One possible reason is lack of buffer space.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.3.1.4.11.1.3

A table for enet port stats

hzCpEnetPortLcStatsEntry row .1.3.6.1.4.1.7262.2.5.3.1.5.1

An entry for enet port stats

Indexes

hzCpEnetPortLcStatsIndex

Column	Syntax	OID
hzCpEnetPortLcStatsIndex A unique value for each enet port.	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.3.1.5.1.1
hzCpEnetPortLcTxFrames A low capacity 32-bit counter representing total number of packets that higher-level protocols requested be transmitted to a subnetwork-unicast address, including those that were discarded or not sent.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.2
hzCpEnetPortLcTxBytes A low capacity 32-bit counter representing total number of packets that higher-level protocols requested be transmitted to a non- unicast (i.e., a subnetwork-broadcast or subnetwork-multicast) address, including those t…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.3
hzCpEnetPortLcRxFramesOk A low capacity 32-bit counter representing total number of bytes received on the interface, including framing characters.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.4
hzCpEnetPortLcRxBytesOk A low capacity 32-bit counter representing the number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One poss…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.5
hzCpEnetPortLcRxFramesLengthErrors A low capacity 32-bit counter representing the number of inbound packets that contained errors preventing them from being deliverable to a higher-layer protocol.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.6
hzCpEnetPortLcRxFramesCrcErrors A low capacity 32-bit counter representing the number of packets received via the interface which were discarded because of rx frames CRC errors.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.7
hzCpEnetPortLcRxDiscarded A low capacity 32-bit counter representing the number of inbound packets which were chosen to be discarded even though no errors had been detected to prevent their being deliverable to a higher-layer protocol. One poss…	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.5.1.8

A table of enet aggregate frames.

hzCpEnetAggLcFramesInQueueEntry row .1.3.6.1.4.1.7262.2.5.3.1.6.11.1

An entry of enet aggregate frames.

Indexes

hzCpEnetAggLcFramesInQueueIndex

Column	Syntax	OID
hzCpEnetAggLcFramesInQueueIndex A unique value for each of the 8 queues.	Enumeration Enumerated Values: 1 q1 2 q2 3 q3 4 q4 5 q5 6 q6 7 q7 8 q8	.1.3.6.1.4.1.7262.2.5.3.1.6.11.1.1
hzCpEnetAggLcFramesInQueue A low capacity 32-bit counter representing the current count of frames in queues.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.6.11.1.2
hzCpEnetAggLcFramesInQueueDiscarded A low capacity 32-bit counter representing the current count of frames received in queues that were discarded due to an error. One possible reason is lack of buffer space.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.3.1.6.11.1.3

A table of enet port vlan setting.

hzCpEnetPortVlanEntry row .1.3.6.1.4.1.7262.2.5.3.1.7.1

An entry of enet port vlan setting.

Indexes

hzCpEnetPortVlanIndex

Column	Syntax	OID
hzCpEnetPortVlanIndex A unique name identifying each enet port.	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.3.1.7.1.1
hzCpEnetPortDefaultVlanId Indicates default VLAN Tag Id (1...4095) per port.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.3.1.7.1.2
hzCpEnetPortDefaultVlanPriority Indicated default VLAN tagging priority (0...7) per port.	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.3.1.7.1.3

A table of Wireless Interface Modems

hzCpWirelessInterfaceNameEntry row .1.3.6.1.4.1.7262.2.5.4.1.1.1

An entry of Wireless Interface Modem

Indexes

hzCpWirelessInterfaceNameIndex

Column	Syntax	OID
hzCpWirelessInterfaceNameIndex A unique value for each Wireless Interface.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.5.4.1.1.1.1
hzCpWirelessInterfaceName Describes the functionality of the Wireless Interface.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.4.1.1.1.2

A table of Wireless Interface Modems

hzCpModemEntry row .1.3.6.1.4.1.7262.2.5.4.2.1.1

An entry of Wireless Interface Modem

Indexes

hzCpModemIndex

Column	Syntax	OID
hzCpModemIndex A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1	.1.3.6.1.4.1.7262.2.5.4.2.1.1.1
hzCpModemOperStatus The current operational state of the interface. Testing indicates that no operational packets can be passed.	Enumeration Enumerated Values: 1 up 2 down 3 testing	.1.3.6.1.4.1.7262.2.5.4.2.1.1.2
hzCpModemChannelizedRSL An estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value. Once this number is divided by 10 the units are dBm. For example -352 is actually -35.2dBm	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.3
hzCpModemChannelizedRSLUnsignedInt The absolute value of the estimate of the modem's channelized RSL. Divide the value by 10 to get the actual RSL value. Once this number is divided by 10 the units are dBm. For example -352 is actually 35.2dBm	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.4
hzCpModemModulationType The modulation type of the modem, distinguished according to the physical/link protocol.	Enumeration Enumerated Values: 1 qpsk 2 qam16 3 qam32 4 qam64 5 qam128 6 qam256 7 qam512 8 qam1024 9 qam2048	.1.3.6.1.4.1.7262.2.5.4.2.1.1.5
hzCpModemRxSpeed An estimate of the modem's current Rx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.6
hzCpModemTxSpeed An estimate of the modem's current Tx bandwidth in bits per second. Divide the value by 10000 to get the actual data rate in Mbps	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.7
hzCpModemSNR SNR value in dB. Divide the value by 10 to get the actual SNR.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.8
hzCpModemEbToNoiseRatio The ratio of the modem Estimated Energy per information bit to Noise power spectral density. Divide the value by 10 to get the actual EbToNoiseRatio	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.9
hzCpModemEqualizerStress Indicates the average magnitude of all the equalizer taps to provide a measure of how hard the equalizer is working.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.2.1.1.10

A table of Wireless Interface Modem Statistics

hzCpWirelessPortStatsEntry row .1.3.6.1.4.1.7262.2.5.4.2.2.1

Statistics for a Wireless Interface Modem

Indexes

hzCpWirelessPortStatsIndex

Column	Syntax	OID
hzCpWirelessPortStatsIndex A unique value for each interface. Wireless-port-1 contains the local aggregate wireless statistics and wireless-port-2 contains the partner aggregate wireless statistics only in redundancy configuration mode.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.5.4.2.2.1.1
hzCpWirelessPortTxBlocks The current count of Modem blocks transmitted.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.4.2.2.1.2
hzCpWirelessPortRxBlocksOKs The current count of Modem blocks received.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.4.2.2.1.3
hzCpWirelessPortRxBlocksErrors The current count of Modem blocks received in error.	SNMPv2-SMICounter64 Type Constraints: range: 0..18446744073709551615	.1.3.6.1.4.1.7262.2.5.4.2.2.1.4

A table of Wireless Interface Modem Statistics

hzCpWirelessPortLcStatsEntry row .1.3.6.1.4.1.7262.2.5.4.2.4.1

Statistics for a Wireless Interface Modem

Indexes

hzCpWirelessPortLcStatsIndex

Column	Syntax	OID
hzCpWirelessPortLcStatsIndex A unique value for each interface. Wireless-port-1 contains the local aggregate wireless statistics and wireless-port-2 contains the partner aggregate wireless statistics only in redundancy configuration mode.	Enumeration Enumerated Values: 1 wireless-port-1 2 wireless-port-2	.1.3.6.1.4.1.7262.2.5.4.2.4.1.1
hzCpWirelessPortLcTxBlocks A low capacity 32-bit counter representing the current count of Modem blocks transmitted.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.4.2.4.1.2
hzCpWirelessPortLcRxBlocksOKs A low capacity 32-bit counter representing the current count of Modem blocks received.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.4.2.4.1.3
hzCpWirelessPortLcRxBlocksErrors A low capacity 32-bit counter representing the current count of Modem blocks received in error.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.4.2.4.1.4

A table of Wireless Interface Radios

hzCpRadioEntry row .1.3.6.1.4.1.7262.2.5.4.4.1.1

An entry of Wireless Interface Radio

Indexes

hzCpRadioIndex

Column	Syntax	OID
hzCpRadioIndex A unique value for each interface.	Enumeration Enumerated Values: 1 wireless-port-1	.1.3.6.1.4.1.7262.2.5.4.4.1.1.1
hzCpRadioDescription A textual string containing information about the radio. Includes the manufacturer, product name, software version, serial number, and hardware version of the radio.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.4.4.1.1.2
hzCpRadioOperStatus The current operational state of the interface. Testing indicates that no operational packets can be passed. Testing also indicates that a firmware upgrade may be in progress	Enumeration Enumerated Values: 1 up 2 down 3 testing	.1.3.6.1.4.1.7262.2.5.4.4.1.1.3
hzCpRadioTxGain The gain of the radio in the transmit chain. Indicates the gain in dB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.4
hzCpRadioRxGain The gain of the radio in the receive chain. Indicates the gain in dB.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.5
hzCpRadioReset Writing 1 to this object causes the radio to be reset. All other values are not recognized. This variable always reads back as 0. radioOperStatus should be polled by the user after this object is written to, to veri…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.6
hzCpRadioTransmitPowerdBm This defines the programmed transmit level of the radio. The power you see is divided by 10. e.g. A display of 133 is actually 13.3 dBm. Notes: - If HAAM is enabled, transmit power cannot be changed. - Programmed and A…	SNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.7
hzCpRadioPowerOption This indicates the power option of the radio: normal or high power.	Enumeration Enumerated Values: 1 normal 2 highPower	.1.3.6.1.4.1.7262.2.5.4.4.1.1.8
hzCpRadioTxState This indicates the power option of the radio: normal or high power.	Enumerationr/w Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.5.4.4.1.1.9
hzCpRadioActualTxState This defines the actual transmit state of the radio.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.5.4.4.1.1.10
hzCpRadioTemperature The Radio temperature in degree Celsius. The actual temperature is determined by dividing the number by 10. e.g. 202 is actually 20.2 degrees Celsius.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.11
hzCpRadioMaxTransmitPowerdBm The maximum Transmit Power allowed.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.12
hzCpRadioActualTransmitPowerdBm This defines the actual transmit level of the radio. The power you see is divided by 10. e.g. A display of 133 is actually 13.3 dBm. This value will be undefined: - If the radio is operational and muted. - If the radio…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.4.1.1.13

A table of radio bands for Radio 1. Frequency bands are divided into sub bands.
          
i.e. FCC 23 Ghz Band is comprised of fcc23a, fcc23b, fcc23c and 
fcc23d which make up the entire FCC23 band

hzCpRadio1BandEntry row .1.3.6.1.4.1.7262.2.5.4.5.1.2.1

A radio band entry containing all the radio band values

Indexes

hzCpRadio1BandIndex

Column	Syntax	OID
hzCpRadio1BandIndex A unique value for each radio band.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.1.2.1.1
hzCpRadio1BandId radio band ID. Changing this option might require a system reset unless the user has permission to set hzCpApplyFrequencyChangesToSystem after the changes.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.1.2.1.2
hzCpRadio1BandName The radio band name.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.4.5.1.2.1.3
hzCpRadio1BandProgrammed Specifies the operating radio band for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.5.4.5.1.2.1.4

A table of txHigh frequency settings for Radio 1

hzCpRadio1FreqEntry row .1.3.6.1.4.1.7262.2.5.4.5.1.3.1

A TX-High or TX-Low Frequency entry containing all the frequency values

Indexes

hzCpRadio1FreqIndex

Column	Syntax	OID
hzCpRadio1FreqIndex A unique value for each frequency channel.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.1.3.1.1
hzCpRadio1FreqChannelIndex The channel index for the frequency.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.4.5.1.3.1.2
hzCpRadio1FreqTransmitRfFrequency The RF TX frequency in KHz.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.1.3.1.3
hzCpRadio1FreqReceiveRfFrequency The RF RX frequency in KHz.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.1.3.1.4
hzCpRadio1FreqProgrammed Specifies the operating frequency channel for the modem. ***Only 1 index may be selected in a 1 modem system.	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.5.4.5.1.3.1.5

A table of system mode settings. Radio Band needs to be configured before the system mode.

hzCpSystemModeEntry row .1.3.6.1.4.1.7262.2.5.4.5.2.1

A system mode entry containing all the system mode values

Indexes

hzCpSystemModeIndex

Column	Syntax	OID
hzCpSystemModeIndex A unique value for each system mode.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.2.1.1
hzCpSystemModeId System mode Id.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.7262.2.5.4.5.2.1.2
hzCpSystemModeName The system mode name.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.4.5.2.1.3
hzCpSystemModeProgrammed Specifies the operating system mode for the modem. Notes: Set Radio Band before System Mode Only 1 index may be selected. Changing this option might require a system reset unless the user has permission …	Enumerationr/w Enumerated Values: 1 active 2 notActive	.1.3.6.1.4.1.7262.2.5.4.5.2.1.4

A table of Q based Threshold Alarm settings

hzCpQBasedThresholdAlarmEntry row .1.3.6.1.4.1.7262.2.5.5.1.2.1.1

An entry based queues.

Indexes

hzCpQBasedThresholdIndex

Column	Syntax	OID
hzCpQBasedThresholdIndex A unique identifier for one of the 8 queues	Enumeration Enumerated Values: 1 q1 2 q2 3 q3 4 q4 5 q5 6 q6 7 q7 8 q8	.1.3.6.1.4.1.7262.2.5.5.1.2.1.1.1
hzCpQBasedDepthThresholdParams The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.5.1.2.1.1.2
hzCpQBasedDroppedFramesThresholdParams The threshold, in percent, and the number of seconds that it must exceed this threshold are programmed by the user. An example of the format of the string is as follows: '70 10'. The first parameter is the percentage of…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.5.1.2.1.1.3

A table of wireless threshold crossing alarms

hzCpWirelessInterfaceThresholdAlarmEntry row .1.3.6.1.4.1.7262.2.5.5.1.3.1

An entry of wireless threshold crossing alarm

Indexes

hzCpWirelessInterfaceThresholdAlarmIndex

Column	Syntax	OID
hzCpWirelessInterfaceThresholdAlarmIndex A unique identifier for each wireless port	Enumeration Enumerated Values: 1 wireless-port-1	.1.3.6.1.4.1.7262.2.5.5.1.3.1.1
hzCpWirelessInterfaceRslThresholdParams A read-write string: The threshold in dBm and the number of seconds threshold are programmed by the user. An example of the format of the string is as follows: '-75 10'. The first parameter power level in dBm, the seco…	SNMPv2-TCDisplayStringr/w Constraints: range: 0-24 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.5.1.3.1.2
hzCpWirelessInterfaceSnrThreshold A read-write string specifing the modem SNR threshold.	SNMPv2-TCDisplayStringr/w Constraints: range: 0-24 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.5.1.3.1.3

A table of alarm configuration

hzCpAlarmConfigEntry row .1.3.6.1.4.1.7262.2.5.5.2.1

An entry of alarm configuration

Indexes

hzCpAlarmConfigIndex hzCpAlarmInstanceIndex

Column	Syntax	OID
hzCpAlarmConfigIndex A unique value for each alarm.	Enumeration Enumerated Values: 1 linkDown 2 peerAuthenticationFailure 3 haamConfigMismatch 4 haamOnLowModulation 5 atpcConfigMismatch 6 atpcAutoDisabled 7 sntpUnreachable 8 freqFileInvalid 9 aggregateDroppedFramesThreshold 10 queueDroppedFramesThreshold 11 bwUtilizationThreshold 12 queueDepthThreshold 13 rlsConfigMismatch 14 rlsShutdownActivated 15 rlsQBasedShutdown 16 modemRxLossOfSignal 17 modemSnrBelowThreshold 18 modemEqStressAboveThreshold 19 rslBelowThershold 20 radioSynthLostLock 21 radioCalTableUnavailable 22 radioCurrentOutOfLimits 23 radioPowerAmp 24 tempOutOfLimits 25 redundancyConfigMismatch 26 redundancyActiveOnSecondary 27 redundancyOperatingInForcedSwitch 28 redundancyEnetCrossLinkActive 29 redundancyActiveUsingPartnerWLink 30 redundancyStandbyWLinkInUse 31 redundancyStandbyOnPrimary 32 x2DeliveringHalfCapacity 33 bncSignalNotDetected 34 ethernetSpeedReduced 35 synceLostLock 36 synceSecondarySourceInUse 37 invalidSysConfig 38 mibChangeNotSaved 39 transmitterLossOfSync 40 radioLinearityCalError 41 synceConfigMismatch 42 cryptoPowerUpTestsFailed 43 cyptoConfigMismatch	.1.3.6.1.4.1.7262.2.5.5.2.1.1
hzCpAlarmInstanceIndex A unique value for each instance of an alarm.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.5.2.1.2
hzCpAlarmConfigSeverity The severity of the alarm as minor, major or critical.	Enumerationr/w Enumerated Values: 1 minor 2 major 3 critical	.1.3.6.1.4.1.7262.2.5.5.2.1.3
hzCpAlarmConfigState The state of the alarm which can be either enabled or disabled.	Enumerationr/w Enumerated Values: 1 disable 2 enable	.1.3.6.1.4.1.7262.2.5.5.2.1.4

A table of alarm status

hzCpAlarmStatusEntry row .1.3.6.1.4.1.7262.2.5.5.3.1

An entry of alarm status

Indexes

hzCpAlarmStatusIndex hzCpAlarmStatusInstanceIndex

Column	Syntax	OID
hzCpAlarmStatusIndex A unique value for each alarm.	Enumeration Enumerated Values: 1 linkDown 2 peerAuthenticationFailure 3 haamConfigMismatch 4 haamOnLowModulation 5 atpcConfigMismatch 6 atpcAutoDisabled 7 sntpUnreachable 8 freqFileInvalid 9 aggregateDroppedFramesThreshold 10 queueDroppedFramesThreshold 11 bwUtilizationThreshold 12 queueDepthThreshold 13 rlsConfigMismatch 14 rlsShutdownActivated 15 rlsQBasedShutdown 16 modemRxLossOfSignal 17 modemSnrBelowThreshold 18 modemEqStressAboveThreshold 19 rslBelowThershold 20 radioSynthLostLock 21 radioCalTableUnavailable 22 radioCurrentOutOfLimits 23 radioPowerAmp 24 tempOutOfLimits 25 redundancyConfigMismatch 26 redundancyActiveOnSecondary 27 redundancyOperatingInForcedSwitch 28 redundancyEnetCrossLinkActive 29 redundancyActiveUsingPartnerWLink 30 redundancyStandbyWLinkInUse 31 redundancyStandbyOnPrimary 32 x2DeliveringHalfCapacity 33 bncSignalNotDetected 34 ethernetSpeedReduced 35 synceLostLock 36 synceSecondarySourceInUse 37 invalidSysConfig 38 mibChangeNotSaved 39 transmitterLossOfSync 40 radioLinearityCalError 41 synceConfigMismatch 42 cryptoPowerUpTestsFailed 43 cryptoConfigMismatch	.1.3.6.1.4.1.7262.2.5.5.3.1.1
hzCpAlarmStatusInstanceIndex A unique value for each instance of an alarm.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.7262.2.5.5.3.1.2
hzCpAlarmStatus Indicates whether the alarm exists or not.	Enumeration Enumerated Values: 1 off 2 on	.1.3.6.1.4.1.7262.2.5.5.3.1.3
hzCpAlarmRaisedDateAndTime Specifies the date and time when the alarm was raised. If the alarm never occured, the value shows as zero.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.7262.2.5.5.3.1.4
hzCpAlarmClearedDateAndTime Specifies the date and time when the alarm was cleared. If the alarm never occured, the value shows as zero.	SNMPv2-TCDateAndTime Type Constraints: range: 8 range: 11 Description: A date-time specification. field octets contents range ----- ------ -------- ----- 1 1-2 year* 0..65536 2 3 month …	.1.3.6.1.4.1.7262.2.5.5.3.1.5

A table of Qos Settings per port

hzCpQosPortConfigEntry row .1.3.6.1.4.1.7262.2.5.6.12.1

An entry of Qos setting per port

Indexes

hzCpCosPortIndex

Column	Syntax	OID
hzCpCosPortIndex A unique name identifying each enet port	Enumeration Enumerated Values: 1 enet-port-1 2 enet-port-2 3 enet-port-3 4 enet-port-4	.1.3.6.1.4.1.7262.2.5.6.12.1.1
hzCpCosQueueMapping User queue assignments for CoS values 0 to 7. There are 8 CoS queues. Their corresponding queue numbers are 1 to 8 where 1 is the lowest priority queue and 8 is the highest priority queue. CoS to queue mapping example:…	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.7262.2.5.6.12.1.2
hzCpCosDefaultValue Default CoS value assigned to the ethernet frames that don't have VLAN or Q-in-Q tag.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.7262.2.5.6.12.1.3