DOT3-OAM-MIB Table View

This table contains the primary controls and status for the
OAM capabilities of an Ethernet-like interface.  There will be
one row in this table for each Ethernet-like interface in the
system that supports the OAM functions defined in [802.3ah].

dot3OamEntry row .1.3.6.1.2.1.158.1.1.1

An entry in the table that contains information on the
Ethernet OAM function for a single Ethernet like interface.
Entries in the table are created automatically for each
interface supporting Ethernet OAM. The status o…

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot3OamAdminState This object is used to provision the default administrative OAM mode for this interface. This object represents the desired state of OAM for this interface. The dot3OamAdminState always starts in the dis…	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.2.1.158.1.1.1.1
dot3OamOperStatus At initialization and failure conditions, two OAM entities on the same full-duplex Ethernet link begin a discovery phase to determine what OAM capabilities may be used on that link. The progress of this …	Enumeration Enumerated Values: 1 disabled 2 linkFault 3 passiveWait 4 activeSendLocal 5 sendLocalAndRemote 6 sendLocalAndRemoteOk 7 oamPeeringLocallyRejected 8 oamPeeringRemotelyRejected 9 operational 10 nonOperHalfDuplex	.1.3.6.1.2.1.158.1.1.1.2
dot3OamMode This object configures the mode of OAM operation for this Ethernet-like interface. OAM on Ethernet interfaces may be in 'active' mode or 'passive' mode. These two modes differ in that active mode provides additional c…	Enumerationr/w Enumerated Values: 1 passive 2 active	.1.3.6.1.2.1.158.1.1.1.3
dot3OamMaxOamPduSize The largest OAMPDU that the OAM entity supports. OA entities exchange maximum OAMPDU sizes and negotiate to use the smaller of the two maximum OAMPDU sizes between the peers. This value is determined by the local imple…	octetsUnsigned32 Constraints: range: 64-1518	.1.3.6.1.2.1.158.1.1.1.4
dot3OamConfigRevision The configuration revision of the OAM entity as reflected in the latest OAMPDU sent by the OAM entity. The config revision is used by OAM entities to indicate that configuration changes have occurred, which might requi…	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.2.1.158.1.1.1.5
dot3OamFunctionsSupported The OAM functions supported on this Ethernet-like interface. OAM consists of separate functional sets beyond the basic discovery process that is always required. These functional groups can be supported independently b…	Bits Enumerated Values: 0 unidirectionalSupport 1 loopbackSupport 2 eventSupport 3 variableSupport	.1.3.6.1.2.1.158.1.1.1.6

This table contains information about the OAM peer for a
particular Ethernet-like interface.  OAM entities communicate
with a single OAM peer entity on Ethernet links on which OA
is enabled and operating properly.  There is one entry in this
table for each entry in the dot3OamTable for which information
on the peer OAM entity is available.

dot3OamPeerEntry row .1.3.6.1.2.1.158.1.2.1

An entry in the table containing information on the peer OA
entity for a single Ethernet-like interface.

Note that there is at most one OAM peer for each Ethernet-like
interface. Entries are automatically …

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot3OamPeerMacAddress The MAC address of the peer OAM entity. The MAC address is derived from the most recently received OAMPDU.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.2.1.158.1.2.1.1
dot3OamPeerVendorOui The OUI of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The OUI can be used to identify the vendor of the remote OA entity. This value is initialized to three octet…	EightOTwoOui Type Constraints: range: 3	.1.3.6.1.2.1.158.1.2.1.2
dot3OamPeerVendorInfo The Vendor Info of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The semantics of the Vendor Information field is proprietary and specific to the vendor (identified by…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.2.1.3
dot3OamPeerMode The mode of the OAM peer as reflected in the latest Information OAMPDU received with a Local Information TLV. The mode of the peer can be determined from the Configuration field in the Local Information TLV of the last…	Enumeration Enumerated Values: 1 passive 2 active 3 unknown	.1.3.6.1.2.1.158.1.2.1.4
dot3OamPeerMaxOamPduSize The maximum size of OAMPDU supported by the peer as reflected in the latest Information OAMPDU received with a Local Information TLV. Ethernet OAM on this interface must not use OAMPDUs that exceed this size. The maxi…	octetsUnsigned32 Constraints: range: 0-0 range: 64-1518	.1.3.6.1.2.1.158.1.2.1.5
dot3OamPeerConfigRevision The configuration revision of the OAM peer as reflected in the latest OAMPDU. This attribute is changed by the peer whenever it has a local configuration change for Ethernet OA on this interface. The configuration rev…	Unsigned32 Constraints: range: 0-65535	.1.3.6.1.2.1.158.1.2.1.6
dot3OamPeerFunctionsSupported The OAM functions supported on this Ethernet-like interface. OAM consists of separate functionality sets above the basic discovery process. This value indicates the capabilities of the peer OAM entity with respect to t…	Bits Enumerated Values: 0 unidirectionalSupport 1 loopbackSupport 2 eventSupport 3 variableSupport	.1.3.6.1.2.1.158.1.2.1.7

This table contains controls for the loopback state of the
local link as well as indicates the status of the loopback
function.  There is one entry in this table for each entry in
dot3OamTable that supports loopback functionality (where
dot3OamFunctionsSupported includes the loopbackSupport bit
set).
          
Loopback can be used to place the remote OAM entity in a state
where every received frame (except OAMPDUs) is echoed back
over the same interface on which they were received.  In this
state, at the remote entity, 'normal' traffic is disabled as
only the looped back frames are transmitted on the interface.
Loopback is thus an intrusive operation that prohibits normal
data flow and should be used accordingly.

dot3OamLoopbackEntry row .1.3.6.1.2.1.158.1.3.1

An entry in the table, containing information on the loopback
status for a single Ethernet-like interface. Entries in the
table are automatically created whenever the local OAM entity
supports loopback capabilities. T…

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot3OamLoopbackStatus The loopback status of the OAM entity. This status is determined by a combination of the local parser and multiplexer states, the remote parser and multiplexer states, as well as by the actions of the local OAM client.…	Enumerationr/w Enumerated Values: 1 noLoopback 2 initiatingLoopback 3 remoteLoopback 4 terminatingLoopback 5 localLoopback 6 unknown	.1.3.6.1.2.1.158.1.3.1.1
dot3OamLoopbackIgnoreRx Since OAM loopback is a disruptive operation (user traffic does not pass), this attribute provides a mechanism to provide controls over whether received OAM loopback commands are processed or ignored. When the value is…	Enumerationr/w Enumerated Values: 1 ignore 2 process	.1.3.6.1.2.1.158.1.3.1.2

This table contains statistics for the OAM function on a
particular Ethernet-like interface.  There is an entry in the
table for every entry in the dot3OamTable.
          
The counters in this table are defined as 32-bit entries to
match the counter size as defined in [802.3ah].  Given that
the OA protocol is a slow protocol, the counters increment at
a slow rate.

dot3OamStatsEntry row .1.3.6.1.2.1.158.1.4.1

An entry in the table containing statistics information on
the Ethernet OAM function for a single Ethernet-like
interface. Entries are automatically created for every entry
in the dot3OamTable. Counters are maintained…

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot3OamInformationTx A count of the number of Information OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.1
dot3OamInformationRx A count of the number of Information OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by the val…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.2
dot3OamUniqueEventNotificationTx A count of the number of unique Event OAMPDUs transmitted on this interface. Event Notifications may be sent in duplicate to increase the probability of successfully being received, given the possibility that a frame m…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.3
dot3OamUniqueEventNotificationRx A count of the number of unique Event OAMPDUs received on this interface. Event Notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a fra…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.4
dot3OamDuplicateEventNotificationTx A count of the number of duplicate Event OAMPDUs transmitted on this interface. Event Notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the p…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.5
dot3OamDuplicateEventNotificationRx A count of the number of duplicate Event OAMPDUs received on this interface. Event Notification OAMPDUs may be sent in duplicate to increase the probability of successfully being received, given the possibility that a …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.6
dot3OamLoopbackControlTx A count of the number of Loopback Control OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.7
dot3OamLoopbackControlRx A count of the number of Loopback Control OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by th…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.8
dot3OamVariableRequestTx A count of the number of Variable Request OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.9
dot3OamVariableRequestRx A count of the number of Variable Request OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.10
dot3OamVariableResponseTx A count of the number of Variable Response OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated b…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.11
dot3OamVariableResponseRx A count of the number of Variable Response OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated by t…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.12
dot3OamOrgSpecificTx A count of the number of Organization Specific OAMPDUs transmitted on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other t…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.13
dot3OamOrgSpecificRx A count of the number of Organization Specific OAMPDUs received on this interface. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as indicated …	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.14
dot3OamUnsupportedCodesTx A count of the number of OAMPDUs transmitted on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at other times as i…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.15
dot3OamUnsupportedCodesRx A count of the number of OAMPDUs received on this interface with an unsupported op-code. Discontinuities of this counter can occur at re-initialization of the management system, and at othe…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.16
dot3OamFramesLostDueToOam A count of the number of frames that were dropped by the OA multiplexer. Since the OAM multiplexer has multiple inputs and a single output, there may be cases where frames are dropped due to transmit resource contentio…	framesSNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.4.1.17

Ethernet OAM includes the ability to generate and receive
Event Notification OAMPDUs to indicate various link problems.
This table contains the mechanisms to enable Event
          
Notifications and configure the thresholds to generate the
standard Ethernet OAM events.  There is one entry in the table
for every entry in dot3OamTable that supports OAM events
(where dot3OamFunctionsSupported includes the eventSupport
bit set).  The values in the table are maintained across
changes to dot3OamOperStatus.
          
The standard threshold crossing events are:
  - Errored Symbol Period Event.  Generated when the number of
    symbol errors exceeds a threshold within a given window
    defined by a number of symbols (for example, 1,000 symbols
    out of 1,000,000 had errors).
  - Errored Frame Period Event.  Generated when the number of
    frame errors exceeds a threshold within a given window
    defined by a number of frames (for example, 10 frames out
    of 1000 had errors).
  - Errored Frame Event.  Generated when the number of frame
    errors exceeds a threshold within a given window defined
    by a period of time (for example, 10 frames in 1 second
    had errors).
  - Errored Frame Seconds Summary Event.  Generated when the
    number of errored frame seconds exceeds a threshold within
    a given time period (for example, 10 errored frame seconds
    within the last 100 seconds).  An errored frame second is
    defined as a 1 second interval which had >0 frame errors.
There are other events (dying gasp, critical events) that are
not threshold crossing events but which can be
enabled/disabled via this table.

dot3OamEventConfigEntry row .1.3.6.1.2.1.158.1.5.1

Entries are automatically created and deleted from this
table, and exist whenever the OAM entity supports Ethernet OA
events (as indicated by the eventSupport bit in
dot3OamFunctionsSuppported). Values in the table are…

Indexes

IF-MIBifIndex

Column	Syntax	OID
dot3OamErrSymPeriodWindowHi The two objects dot3OamErrSymPeriodWindowHi and dot3OamErrSymPeriodLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as dot3OamEr…	2^32 symbolsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.1
dot3OamErrSymPeriodWindowLo The two objects dot3OamErrSymPeriodWindowHi and dot3OamErrSymPeriodWindowLo together form an unsigned 64-bit integer representing the number of symbols over which this threshold event is defined. This is defined as …	symbolsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.2
dot3OamErrSymPeriodThresholdHi The two objects dot3OamErrSymPeriodThresholdHi and dot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this eve…	2^32 symbolsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.3
dot3OamErrSymPeriodThresholdLo The two objects dot3OamErrSymPeriodThresholdHi and dot3OamErrSymPeriodThresholdLo together form an unsigned 64-bit integer representing the number of symbol errors that must occur within a given window to cause this eve…	symbolsSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.4
dot3OamErrSymPeriodEvNotifEnable If true, the OAM entity should send an Event Notification OAMPDU when an Errored Symbol Period Event occurs. By default, this object should have the value true for Ethernet-like interfaces that support OA…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.5
dot3OamErrFramePeriodWindow The number of frames over which the threshold is defined. The default value of the window is the number of minimum size Ethernet frames that can be received over the physical layer in one second. If dot3O…	framesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.6
dot3OamErrFramePeriodThreshold The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of ev…	framesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.7
dot3OamErrFramePeriodEvNotifEnable If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Period Event occurs. By default, this object should have the value true for Ethernet-like interfaces that support OAM…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.8
dot3OamErrFrameWindow The amount of time (in 100ms increments) over which the threshold is defined. The default value is 10 (1 second). If dot3OamErrFrameThreshold frame errors occur within a window of dot3OamErrFrameWindow s…	tenths of a secondSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.9
dot3OamErrFrameThreshold The number of frame errors that must occur for this event to be triggered. The default value is one frame error. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically (at the end of ev…	framesSNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.5.1.10
dot3OamErrFrameEvNotifEnable If true, the OAM entity should send an Event Notification OAMPDU when an Errored Frame Event occurs. By default, this object should have the value true for Ethernet-like interfaces that support OAM. If t…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.11
dot3OamErrFrameSecsSummaryWindow The amount of time (in 100 ms intervals) over which the threshold is defined. The default value is 100 (10 seconds). If dot3OamErrFrameSecsSummaryThreshold frame errors occur within a window of dot3OamEr…	tenths of a secondInteger32r/w Constraints: range: 100-9000	.1.3.6.1.2.1.158.1.5.1.12
dot3OamErrFrameSecsSummaryThreshold The number of errored frame seconds that must occur for this event to be triggered. The default value is one errored frame second. If the threshold value is zero, then an Event Notification OAMPDU is sent periodically…	errored frame secondsInteger32r/w Constraints: range: 1-900	.1.3.6.1.2.1.158.1.5.1.13
dot3OamErrFrameSecsEvNotifEnable If true, the local OAM entity should send an Event Notification OAMPDU when an Errored Frame Seconds Event occurs. By default, this object should have the value true for Ethernet-like interfaces that supp…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.14
dot3OamDyingGaspEnable If true, the local OAM entity should attempt to indicate a dying gasp via the OAMPDU flags field to its peer OAM entity when a dying gasp event occurs. The exact definition of a dying gasp event is implementation depen…	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.15
dot3OamCriticalEventEnable If true, the local OAM entity should attempt to indicate a critical event via the OAMPDU flags to its peer OAM entity when a critical event occurs. The exact definition of a critical event is implementation dependent. …	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.2.1.158.1.5.1.16

This table records a history of the events that have occurred
at the Ethernet OAM level.  These events can include locally
detected events, which may result in locally generated
OAMPDUs, and remotely detected events, which are detected by
the OAM peer entity and signaled to the local entity via
          
Ethernet OAM.  Ethernet OAM events can be signaled by Event
Notification OAMPDUs or by the flags field in any OAMPDU.
          
This table contains both threshold crossing events and
non-threshold crossing events.  The parameters for the
threshold window, threshold value, and actual value
(dot3OamEventLogWindowXX, dot3OamEventLogThresholdXX,
dot3OamEventLogValue) are only applicable to threshold
crossing events, and are returned as all F's (2^32 - 1) for
non-threshold crossing events.
          
Entries in the table are automatically created when such
events are detected.  The size of the table is implementation
dependent.  When the table reaches its maximum size, older
entries are automatically deleted to make room for newer
entries.

dot3OamEventLogEntry row .1.3.6.1.2.1.158.1.6.1

An entry in the dot3OamEventLogTable. Entries are
automatically created whenever Ethernet OAM events occur at
the local OAM entity, and when Event Notification OAMPDUs are
received at the local OAM entity (indicating t…

Indexes

IF-MIBifIndex dot3OamEventLogIndex

Column	Syntax	OID
dot3OamEventLogIndex An arbitrary integer for identifying individual events within the event log.	Unsigned32 Constraints: range: 1-4294967295	.1.3.6.1.2.1.158.1.6.1.1
dot3OamEventLogTimestamp The value of sysUpTime at the time of the logged event. For locally generated events, the time of the event can be accurately retrieved from sysUpTime. For remotely generated events, the time of the event is indicated…	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.2.1.158.1.6.1.2
dot3OamEventLogOui The OUI of the entity defining the object type. All IEEE 802.3 defined events (as appearing in [802.3ah] except for the Organizationally Unique Event TLVs) use the IEEE 802.3 OUI of 0x0180C2. Organizations defining th…	EightOTwoOui Type Constraints: range: 3	.1.3.6.1.2.1.158.1.6.1.3
dot3OamEventLogType The type of event that generated this entry in the event log. When the OUI is the IEEE 802.3 OUI of 0x0180C2, the following event types are defined: erroredSymbolEvent(1), erroredFramePeriodEvent(2), errored…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.4
dot3OamEventLogLocation Whether this event occurred locally (local(1)), or was received from the OAM peer via Ethernet OAM (remote(2)).	Enumeration Enumerated Values: 1 local 2 remote	.1.3.6.1.2.1.158.1.6.1.5
dot3OamEventLogWindowHi If the event represents a threshold crossing event, the two objects dot3OamEventWindowHi and dot3OamEventWindowLo, form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold …	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.6
dot3OamEventLogWindowLo If the event represents a threshold crossing event, the two objects dot3OamEventWindowHi and dot3OamEventWindowLo form an unsigned 64-bit integer yielding the window over which the value was measured for the threshold c…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.7
dot3OamEventLogThresholdHi If the event represents a threshold crossing event, the two objects dot3OamEventThresholdHi and dot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing even…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.8
dot3OamEventLogThresholdLo If the event represents a threshold crossing event, the two objects dot3OamEventThresholdHi and dot3OamEventThresholdLo form an unsigned 64-bit integer yielding the value that was crossed for the threshold crossing even…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.9
dot3OamEventLogValue If the event represents a threshold crossing event, this value indicates the value of the parameter within the given window that generated this event (for example, 11, when 11 occurrences happened in 5 seconds while the…	HCNUM-TCCounterBasedGauge64	.1.3.6.1.2.1.158.1.6.1.10
dot3OamEventLogRunningTotal Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-thresho…	HCNUM-TCCounterBasedGauge64	.1.3.6.1.2.1.158.1.6.1.11
dot3OamEventLogEventTotal Each Event Notification TLV contains a running total of the number of times an event has occurred, as well as the number of times an Event Notification for the event has been transmitted. For non-threshold crossing eve…	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.2.1.158.1.6.1.12