DKSF-60-4-X-X-X Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
6
Rows
6
Columns
38

npRelayTable

table
.1.3.6.1.4.1.25728.5500.5 · 1 row entry · 6 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npRelayTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npRelayTable' 
Watchdog and outlet/relay control table
npRelayEntry row .1.3.6.1.4.1.25728.5500.5.1
Relay/outlet table row
Indexes
Column Syntax OID
npRelayN
The N of output relay
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.25728.5500.5.1.1
npRelayMode
Control of relay:
0 - manual off
1 - manual on
2 - watchdog
3 - schedule
4 - both schedule and watchdog (while switched on by schedule)
5 - logic
Enumerationr/w
Enumerated Values:
0off
1on
2watchdog
3schedule
4scheduleAndWatchdog
5logic
 .1.3.6.1.4.1.25728.5500.5.1.2
npRelayStartReset
Write 1 to start reset (switch relay off for some time)
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.25728.5500.5.1.3
npRelayMemo
Relay memo
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.25728.5500.5.1.6
npRelayFlip
Write -1 to flip between manual on and manual off states of relay
Enumerationr/w
Enumerated Values:
-1flip
 .1.3.6.1.4.1.25728.5500.5.1.14
npRelayState
Actual relay state at the moment,
regardless of source of control.
0 - relay is off
1 - relay is on
Enumeration
Enumerated Values:
0off
1on
 .1.3.6.1.4.1.25728.5500.5.1.15

npPwrTable

table
.1.3.6.1.4.1.25728.5800.3 · 1 row entry · 8 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npPwrTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npPwrTable' 
Watchdog and outlet/relay control table
npPwrEntry row .1.3.6.1.4.1.25728.5800.3.1
Watchdog and outlet/relay control table row
Indexes
Column Syntax OID
npPwrChannelN
The id of watchdog/power channel
Integer32
Constraints:
range: 1-2
 .1.3.6.1.4.1.25728.5800.3.1.1
npPwrStartReset
Write 1 to start forced reset
On read:
0 - normal operation
1 - reset is active
2 - reboot pause is active or watchdog is inactive
Integer32r/w
Constraints:
range: 0-2
 .1.3.6.1.4.1.25728.5800.3.1.2
npPwrManualMode
Mode of power channel
0 - manual off
1 - manual on
2 - watchdog
3 - schedule
4 - schedule and watchdog
5 - controlled by Logic
Enumerationr/w
Enumerated Values:
0off
1on
2watchdog
3schedule
4scheduleAndWatchdog
5logic
 .1.3.6.1.4.1.25728.5800.3.1.3
npPwrResetsCounter
Counter of watchdog resets
Write 0 to clear.
Integer32r/w
Constraints:
range: 0-65535
 .1.3.6.1.4.1.25728.5800.3.1.4
npPwrRepeatingResetsCounter
Counter of continous failed
watchdog resets
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.25728.5800.3.1.5
npPwrMemo
Relay channel memo
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.25728.5800.3.1.6
npPwrRelayFlip
Write -1 to flip between manual on and manual off states of relay
Enumerationr/w
Enumerated Values:
-1flip
 .1.3.6.1.4.1.25728.5800.3.1.14
npPwrRelayState
Actual relay state at the moment,
regardless of source of control.
0 - relay is off
1 - relay is on
Enumeration
Enumerated Values:
0off
1on
 .1.3.6.1.4.1.25728.5800.3.1.15

npCurLoopTable

table
.1.3.6.1.4.1.25728.8300.1 · 1 row entry · 6 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npCurLoopTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npCurLoopTable' 
Current loop sensors Table
npCurLoopEntry row .1.3.6.1.4.1.25728.8300.1.1
Current loop sensors Table Row
Indexes
Column Syntax OID
npCurLoopN
Index of current loop, 1 to max supported
Integer32
Constraints:
range: 1-8
 .1.3.6.1.4.1.25728.8300.1.1.1
npCurLoopStatus
Status of the loop
0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered
Enumeration
Enumerated Values:
0ok
1alert
2cut
3short
4notPowered
 .1.3.6.1.4.1.25728.8300.1.1.2
npCurLoopI
Loop current, mA
Integer32
Constraints:
range: 0-99999
 .1.3.6.1.4.1.25728.8300.1.1.3
npCurLoopV
Voltage drop on the loop, mV
Integer32
Constraints:
range: 0-99999
 .1.3.6.1.4.1.25728.8300.1.1.4
npCurLoopR
Resistance of the loop, Ohm
Integer32
Constraints:
range: 0-99999
 .1.3.6.1.4.1.25728.8300.1.1.5
npCurLoopPower
Control of loop power
0=Off, 1=On, 2=reset by off/on power
Enumerationr/w
Enumerated Values:
0off
1on
2cyclePower
 .1.3.6.1.4.1.25728.8300.1.1.7

npThermoTable

table
.1.3.6.1.4.1.25728.8800.1 · 1 row entry · 6 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npThermoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npThermoTable' 
Thermo Sensors Table
npThermoEntry row .1.3.6.1.4.1.25728.8800.1.1
Thermo Sensors Table Row
Indexes
Column Syntax OID
npThermoSensorN
The id of temperature sensor, 1 to 8
Integer32
Constraints:
range: 1-8
 .1.3.6.1.4.1.25728.8800.1.1.1
npThermoValue
Temperature, deg.C
Integer32
Constraints:
range: -60-280
 .1.3.6.1.4.1.25728.8800.1.1.2
npThermoStatus
Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)
Enumeration
Enumerated Values:
0failed
1low
2norm
3high
 .1.3.6.1.4.1.25728.8800.1.1.3
npThermoLow
Bottom margin of normal temperature range, deg.C
Integer32
Constraints:
range: -60-280
 .1.3.6.1.4.1.25728.8800.1.1.4
npThermoHigh
Top margin of normal temperature range, deg.C
Integer32
Constraints:
range: -60-280
 .1.3.6.1.4.1.25728.8800.1.1.5
npThermoMemo
T channel memo
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.25728.8800.1.1.6

npIoTable

table
.1.3.6.1.4.1.25728.8900.1 · 1 row entry · 7 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npIoTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npIoTable' 
Digital Input/output Table
npIoEntry row .1.3.6.1.4.1.25728.8900.1.1
Digital Input/output Table Row
Indexes
Column Syntax OID
npIoLineN
Number of IO line, from 1 to max supported
Integer32
Constraints:
range: 1-16
 .1.3.6.1.4.1.25728.8900.1.1.1
npIoLevelIn
Input level, 0 or 1
Integer32
Constraints:
range: 0-1
 .1.3.6.1.4.1.25728.8900.1.1.2
npIoLevelOut
Output level, 0 or 1.
Write -1 to flip output.
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.25728.8900.1.1.3
npIoMemo
IO line memo
SNMPv2-TCDisplayString
Type Constraints:
range: 0..255
Description:
Represents textual information taken from the NVT ASCII

character set, as defined in pages 4, 10-11 of RFC 854.

To summarize RFC 854, the NVT ASCII repertoire specifies:

- the use of c…
 .1.3.6.1.4.1.25728.8900.1.1.6
npIoPulseCounter
Pulse Counter on IO input line (counts positive fronts)
Write 0 to reset.
SNMPv2-SMICounter32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.25728.8900.1.1.9
npIoSinglePulseDuration
Set duration of single pulse on IO output line,
100ms to 25500ms, min. step is 100ms
Integer32r/w
Constraints:
range: 100-25500
 .1.3.6.1.4.1.25728.8900.1.1.12
npIoSinglePulseStart
Write 1 to start single pulse on IO output.
Output will be inverted for time, specified by npIoSinglePulseDuration
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.25728.8900.1.1.13

npElecTable

table
.1.3.6.1.4.1.25728.9700.1 · 1 row entry · 5 columns
Open in standard view
Uses the netping variant from /opt/observium/mibs/netping.
Command help
Walk npElecTable
/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-60-4-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-60-4-X-X-X::npElecTable' 
Electricity Meter Table
npElecEntry row .1.3.6.1.4.1.25728.9700.1.1
Electricity Meter Table Table Row
Indexes
Column Syntax OID
npElecIndex
Number of elec.meter, associated with IO line
Integer32
Constraints:
range: 1-4
 .1.3.6.1.4.1.25728.9700.1.1.1
npElecPulsesPerKwh
Pulses on IO line input per 1 kWh of consumed energy
SNMPv2-SMIInteger32r/w
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.25728.9700.1.1.2
npElecPower
Power, Watts, based on pulse rate/interval, 5 minute average
SNMPv2-SMIGauge32
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.25728.9700.1.1.3
npElecEnergy
Energy counter, kWh, based on pulse count
SNMPv2-SMICounter32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.25728.9700.1.1.4
npElecEnergy100
Energy counter, kWh*100, based on pulse count
SNMPv2-SMICounter32r/w
Type Constraints:
range: 0..4294967295
 .1.3.6.1.4.1.25728.9700.1.1.5