DKSF-50-11-X-X-X Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

npPwrTable

table

.1.3.6.1.4.1.25728.5800.3 · 1 row entry · 6 columns

Open in standard view

Uses the netping variant from /opt/observium/mibs/netping.

Command help

Walk npPwrTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-50-11-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-50-11-X-X-X::npPwrTable'

Watchdog and outlet/relay control table

npPwrEntry row .1.3.6.1.4.1.25728.5800.3.1

Watchdog and outlet/relay control table row

Indexes

No indexes recorded

Column	Syntax	OID
npPwrChannelN The id of watchdog/power channel	Integer32	`.1.3.6.1.4.1.25728.5800.3.1.1`
npPwrStartReset Write 1 to start reset On read: 0 - normal operation 1 - reset is active 2 - reboot pause is active	Integer32r/w	`.1.3.6.1.4.1.25728.5800.3.1.2`
npPwrManualMode Mode of power channel 0 - manual off 1 - manual on 2 - watchdog	Enumerationr/w	`.1.3.6.1.4.1.25728.5800.3.1.3`
npPwrResetsCounter Counter of watchdog resets Write 0 to clear.	Integer32r/w	`.1.3.6.1.4.1.25728.5800.3.1.4`
npPwrRepeatingResetsCounter Counter of continous failed watchdog resets	Integer32	`.1.3.6.1.4.1.25728.5800.3.1.5`
npPwrMemo Watchdog/power channel memo	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.25728.5800.3.1.6`

npCurLoopTable

table

.1.3.6.1.4.1.25728.8300.1 · 1 row entry · 6 columns

Open in standard view

Uses the netping variant from /opt/observium/mibs/netping.

Command help

Walk npCurLoopTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-50-11-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-50-11-X-X-X::npCurLoopTable'

Current loop sensors Table

npCurLoopEntry row .1.3.6.1.4.1.25728.8300.1.1

Current loop sensors Table Row

Indexes

No indexes recorded

Column	Syntax	OID
npCurLoopN Index of current loop, 1 to max supported	Integer32	`.1.3.6.1.4.1.25728.8300.1.1.1`
npCurLoopStatus Status of the loop 0=Normal, 1=Alert, 2=Cut, 3=Short, 4=Not Powered	Enumeration	`.1.3.6.1.4.1.25728.8300.1.1.2`
npCurLoopI Loop current, mA	Integer32	`.1.3.6.1.4.1.25728.8300.1.1.3`
npCurLoopV Voltage drop on the loop, mV	Integer32	`.1.3.6.1.4.1.25728.8300.1.1.4`
npCurLoopR Resistance of the loop, Ohm	Integer32	`.1.3.6.1.4.1.25728.8300.1.1.5`
npCurLoopPower Control of loop power 0=Off, 1=On, 2=reset by off/on power	Enumerationr/w	`.1.3.6.1.4.1.25728.8300.1.1.7`

npThermoTable

table

.1.3.6.1.4.1.25728.8800.1 · 1 row entry · 6 columns

Open in standard view

Uses the netping variant from /opt/observium/mibs/netping.

Command help

Walk npThermoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-50-11-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-50-11-X-X-X::npThermoTable'

Thermo Sensors Table

npThermoEntry row .1.3.6.1.4.1.25728.8800.1.1

Thermo Sensors Table Row

Indexes

No indexes recorded

Column	Syntax	OID
npThermoSensorN The id of temperature sensor, 1 to 8	Integer32	`.1.3.6.1.4.1.25728.8800.1.1.1`
npThermoValue Temperature, deg.C	Integer32	`.1.3.6.1.4.1.25728.8800.1.1.2`
npThermoStatus Temperature status (0=fault, 1=underheat, 2=normal, 3=overheat)	Enumeration	`.1.3.6.1.4.1.25728.8800.1.1.3`
npThermoLow Bottom margin of normal temperature range, deg.C	Integer32	`.1.3.6.1.4.1.25728.8800.1.1.4`
npThermoHigh Top margin of normal temperature range, deg.C	Integer32	`.1.3.6.1.4.1.25728.8800.1.1.5`
npThermoMemo T channel memo	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.25728.8800.1.1.6`

npIoTable

table

.1.3.6.1.4.1.25728.8900.1 · 1 row entry · 7 columns

Open in standard view

Uses the netping variant from /opt/observium/mibs/netping.

Command help

Walk npIoTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'DKSF-50-11-X-X-X' -M '/opt/observium/mibs/netping:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'DKSF-50-11-X-X-X::npIoTable'

Digital Input/output Table

npIoEntry row .1.3.6.1.4.1.25728.8900.1.1

Digital Input/output Table Row

Indexes

No indexes recorded

Column	Syntax	OID
npIoLineN Number of IO line, from 1 to max supported	Integer32	`.1.3.6.1.4.1.25728.8900.1.1.1`
npIoLevelIn Input level, 0 or 1	Integer32	`.1.3.6.1.4.1.25728.8900.1.1.2`
npIoLevelOut Output level, 0 or 1	Integer32r/w	`.1.3.6.1.4.1.25728.8900.1.1.3`
npIoMemo IO line memo	SNMPv2-TCDisplayString Type Constraints: `range: 0..255` Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	`.1.3.6.1.4.1.25728.8900.1.1.6`
npIoPulseCounter Pulse Counter on IO input line (counts positive fronts) Write 0 to reset.	SNMPv2-SMICounter32r/w Type Constraints: `range: 0..4294967295`	`.1.3.6.1.4.1.25728.8900.1.1.9`
npIoSinglePulseDuration Set duration of single pulse on IO output line, 100ms to 25500ms, min. step is 100ms	Integer32r/w	`.1.3.6.1.4.1.25728.8900.1.1.12`
npIoSinglePulseStart Write 1 to start single pulse on IO output. Output will be inverted for time, specified by npIoSinglePulseDuration	SNMPv2-SMIInteger32r/w Type Constraints: `range: -2147483648..2147483647`	`.1.3.6.1.4.1.25728.8900.1.1.13`