DGS3216-SWL3MGMT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view
Tables
3
Rows
3
Columns
35

swL3IpCtrlTable

table
.1.3.6.1.4.1.171.11.101.2.3.2.1.3 · 1 row entry · 14 columns
Open in standard view 
This table contains IP interface information.
swL3IpCtrlEntry entry .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1
A list of information about a specific IP interface.
Indexes
swL3IpCtrlInterfaceName
Column Syntax OID
swL3IpCtrlInterfaceName
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.1
swL3IpCtrlIfIndex
This object uniquely identifies the IP interface number in the
swL3IpCtrlTable.
Integer32
Constraints:
range: 0-65535
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.2
swL3IpCtrlIpAddr
The IP address of the interface. This object only can take the
value of the unicast IP address.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.3
swL3IpCtrlIpSubnetMask
The IP net mask for this interface.
SNMPv2-SMIIpAddressr/w
Textual Convention: SNMPv2-SMIIpAddress OctetString
Type Constraints:
range: 4
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.4
swL3IpCtrlVlanName
This object indicates the IP control entry's VLAN name. The
VLAN name in each entry must be unique in the IP Control Table.
OctetStringr/w
Constraints:
range: 0-32
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.5
swL3IpCtrlMode
This object indicates the IP operation mode.

other(1) - This entry is currently in use but the conditions under
which it will remain are determined by each of the following values.
bootp(3) - The I…
Enumerationr/w
Enumerated Values:
1other
3bootp
4dhcp
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.8
swL3IpCtrlAdminState
The state of the IP interface.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.9
swL3IpCtrlIpv6LinkLocalAddress
The IPv6 link local address for this interface.
Ipv6Address
Textual Convention: Ipv6Address OctetString
Type Constraints:
range: 16
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.14
swL3IpCtrlIpv6LinkLocalPrefixLen
The IPv6 prefix length for this IPv6 link local address.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.15
swL3IpCtrlState
This variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.16
swL3IpCtrlIpv6LinkLocalAutoState
The state of the IPv6 link local auto.
Enumerationr/w
Enumerated Values:
1other
2enabled
3disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.17
swL3IpCtrlDhcpv6ClientState
The object indicates the state of the DHCPv6 client.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.20
swL3IpCtrlIpDhcpOption12State
Enable or disable insertion of option 12 in the DHCPDISCOVER and
DHCPREQUEST message.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.22
swL3IpCtrlIpDhcpOption12HostName
Specify the host name to be inserted in the DHCPDISCOVER and
DHCPREQUEST message. The specified host name must start with a
letter, end with a letter or digit, and have only letters, digits,
and hyphen as interior ch…
OctetStringr/w
Constraints:
range: 0-63
 .1.3.6.1.4.1.171.11.101.2.3.2.1.3.1.23

swL3Ipv6CtrlTable

table
.1.3.6.1.4.1.171.11.101.2.3.2.1.4 · 1 row entry · 12 columns
Open in standard view 
This table contains IPv6 information of an IP interface.
swL3Ipv6CtrlEntry entry .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1
A list of IPv6 information about a specific IP interface.
Indexes
swL3Ipv6CtrlInterfaceName
Column Syntax OID
swL3Ipv6CtrlInterfaceName
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.1
swL3Ipv6CtrlMaxReassmblySize
Maximum Reassembly Size of the IP interface.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.2
swL3Ipv6CtrlNsRetransTimer
Neighbor solicitation's retransmit timer.
The unit is set in milliseconds.
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.3
swL3Ipv6CtrlRaState
Neighbor solicited state.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.5
swL3Ipv6CtrlRaMinRtrAdvInterval
The minimum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInt…
Integer32r/w
Constraints:
range: 3-1350
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.6
swL3Ipv6CtrlRaMaxRtrAdvInterval
The maximum time allowed between sending unsolicited multicast Router
Advertisements from the interface. The unit is set in seconds.
Integer32r/w
Constraints:
range: 4-1800
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.7
swL3Ipv6CtrlRaLifeTime
Indicates the lifetime of the router as the default router.
Integer32r/w
Constraints:
range: 0-9000
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.8
swL3Ipv6CtrlRaReachableTime
Indicates the amount of time that a node can consider a neighboring
node reachable after receiving a reachability confirmation.
Integer32r/w
Constraints:
range: 0-3600000
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.9
swL3Ipv6CtrlRaRetransTime
Indicates the amount of time between retransmissions of neighbor
solicited messages.
The unit is set in millisecond.
Unsigned32r/w
Constraints:
range: 0-4294967295
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.10
swL3Ipv6CtrlRaHopLimit
Indicates the default value of the hop limit field in the IPv6 header for
packets sent by hosts that receive this RA message.
Integer32r/w
Constraints:
range: 0-255
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.11
swL3Ipv6CtrlRaManagedFlag
When enabled, it indicates that hosts receiving this RA must use a
stateful address configuration protocol to obtain an address in the addition
to the addresses derived from the stateless address configuration.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.12
swL3Ipv6CtrlRaOtherConfigFlag
When enabled, it indicates that hosts receiving this RA must use a stateful
address configuration protocol to obtain an on-link address configuration information.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.4.1.13

swL3Ipv6AddressCtrlTable

table
.1.3.6.1.4.1.171.11.101.2.3.2.1.5 · 1 row entry · 9 columns
Open in standard view 
This table contains IPv6 address information for each IP interface.
swL3Ipv6AddressCtrlEntry entry .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1
A list of information about a specific IPv6 address.
Indexes
swL3Ipv6AddressCtrlInterfaceName swL3Ipv6Address swL3Ipv6AddressCtrlPrefixLen
Column Syntax OID
swL3Ipv6AddressCtrlInterfaceName
This object indicates the name of the IP interface.
OctetString
Constraints:
range: 1-12
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.1
swL3Ipv6Address
Specify the IPv6 address.
Ipv6Address
Textual Convention: Ipv6Address OctetString
Type Constraints:
range: 16
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.2
swL3Ipv6AddressCtrlPrefixLen
Indicates the prefix length of this IPv6 address.
SNMPv2-SMIInteger32
Textual Convention: SNMPv2-SMIInteger32 Integer32
Type Constraints:
range: -2147483648..2147483647
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.3
swL3Ipv6AddressCtrlPreferredLifeTime
Indicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains in preferred state.
For an infinite valid lifetime, the value can be set to 0xfffffff…
Unsigned32r/w
Constraints:
range: 0-4294967294
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.4
swL3Ipv6AddressCtrlValidLifeTime
Indicates the number of seconds that an address, based on the specified prefix,
using the stateless address configuration, remains valid.
For an infinite valid lifetime, the value can be set to 0xffffffff.
Unsigned32r/w
Constraints:
range: 0-4294967294
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.5
swL3Ipv6AddressCtrlOnLinkFlag
When enabled, the address implied by the specified prefix is available
on the link where the RA message is received.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.6
swL3Ipv6AddressCtrlAutonomousFlag
When enabled, the specified prefix will be used to create an autonomous address configuration.
Enumerationr/w
Enumerated Values:
1enabled
2disabled
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.7
swL3Ipv6AddressCtrlState
This variable displays the status of the entry. The status is used
for creating, modifying, and deleting instances of the objects
in this table.
SNMPv2-TCRowStatusr/w
Textual Convention: SNMPv2-TCRowStatus Enumeration
Type Values:
1active
2notInService
3notReady
4createAndGo
5createAndWait
6destroy
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.8
swL3Ipv6AddressCtrlAddressType
This object indicates the type of the IPv6 address.
manual(1): the IPv6 address is configured by user.
dhcpv6(2): the IPv6 address is assigned by DHCPv6 server.
stateless(3): the IPv6 address is assigned by router adver…
Enumeration
Enumerated Values:
1manual
2dhcpv6
3stateless
 .1.3.6.1.4.1.171.11.101.2.3.2.1.5.1.9