DGS-3700-12-L2MGMT-MIB Table View

A table containing CFM state of speicified ports.

swL2DevCtrlCFMPortEntry row .1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1

The entry of CFM state on speicified ports.

Indexes

No indexes recorded

Column	Syntax	OID
swL2DevCtrlCFMPortIndex This object indicates the port-num.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1.1
swL2DevCtrlCFMPortState This object indicates the CFM state on per-port.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.1.2.21.2.1.2

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

swL2VlanStaticEntry row .1.3.6.1.4.1.171.11.102.1.1.2.2.1.1

Static information for a VLAN configured into the
device by (local or network) management.

Indexes

No indexes recorded

Column	Syntax	OID
swL2VlanIndex The VLAN-ID or other identifier referring to this VLAN.	VlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.171.11.102.1.1.2.2.1.1.1
swL2VLANAdvertisement This object indicates if the advertisement is active or not.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.2.1.1.2

A table containing vlan and port role information of each port.

swL2VlanPortInfoEntry row .1.3.6.1.4.1.171.11.102.1.1.2.2.3.1

The table entry of vlan port information.

Indexes

No indexes recorded

Column	Syntax	OID
swL2VlanPortInfoPortIndex The port index.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.1
swL2VlanPortInfoVid The VLAN-ID assigned to a special port	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.2
swL2VlanPortInfoPortRole The port role of a special port.when none,it means this port is not belong to the vlan.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.2.3.1.3

A table that contains information about every port.

swL2PortInfoEntry row .1.3.6.1.4.1.171.11.102.1.1.2.3.1.1

A list of information for each port of the device.

Indexes

No indexes recorded

Column	Syntax	OID
swL2PortInfoPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.1
swL2PortInfoMediumType Indicates medium type of the port number.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.2
swL2PortInfoUnitID Indicates ID of the unit in the system	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.3
swL2PortInfoType This object indicates the connector type of this port.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.4
swL2PortInfoLinkStatus This object indicates the port link status.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.5
swL2PortInfoNwayStatus This object indicates the port speed and duplex mode.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.6
swL2PortInfoErrorDisabled This object indicates the blocking type of this port.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.1.1.8

A table that contains control information about every port.

swL2PortCtrlEntry row .1.3.6.1.4.1.171.11.102.1.1.2.3.2.1

A list of control information for each port of the device.

Indexes

No indexes recorded

Column	Syntax	OID
swL2PortCtrlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.1
swL2PortCtrlMediumType Indicates medium type of the port number.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.2
swL2PortCtrlUnitIndex Indicates ID of the unit in the device	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.3
swL2PortCtrlAdminState This object decides if the port is enabled or disabled.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.4
swL2PortCtrlNwayState Chose the port speed, duplex mode, and N-Way function mode.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.5
swL2PortCtrlFlowCtrlState The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and…	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.6
swL2PortCtrlLearningState This object decides if the port is locked or not.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.7
swL2PortCtrlMACNotifyState This object sets each port's MAC notification state.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.2.1.8

A table that used to clear counter information about every port.

swL2PortCounterCtrlEntry row .1.3.6.1.4.1.171.11.102.1.1.2.3.6.1

A list of entry used to clear counter information for each port of the device.

Indexes

No indexes recorded

Column	Syntax	OID
swL2PortCounterCtrlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.6.1.1
swL2PortCounterClearCtrl This object indicates if to clear the counters for each port of the device or not.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.3.6.1.2

A table that contains error information for each port.

swL2PortErrEntry row .1.3.6.1.4.1.171.11.102.1.1.2.3.7.1

A list of information regarding port errors on the device.

Indexes

No indexes recorded

Column	Syntax	OID
swL2PortErrPortIndex This object indicates the module's port number.(1..Max port number in the module).	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.1
swL2PortErrPortState This object indicates the port state is enabled or disabled.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.2
swL2PortErrPortConnStatus This object indicates whether the PortStatus is err-disabled or not.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.3
swL2PortErrPortReason This object describes if the reason for the port error is STP LBD or Storm control.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.3.7.1.4

This table specifies which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkCtrlEntry row .1.3.6.1.4.1.171.11.102.1.1.2.9.3.1

A list of information that specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

No indexes recorded

Column	Syntax	OID
swL2TrunkIndex The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.1
swL2TrunkMasterPort The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port (…	Integer32r/w	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.3
swL2TrunkMember Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.4
swL2TrunkFloodingPort The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.5
swL2TrunkType This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.6
swL2TrunkState This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.102.1.1.2.9.3.1.7

This table specifies which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkLACPPortEntry row .1.3.6.1.4.1.171.11.102.1.1.2.9.5.1

A list of information specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

No indexes recorded

Column	Syntax	OID
swL2TrunkLACPPortIndex The index of logical port LACP.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.9.5.1.1
swL2TrunkLACPPortState The state of logical port LACP.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.9.5.1.2

This table specifies that the port can just forward traffic to the
specific port list.

swL2TrafficSegEntry row .1.3.6.1.4.1.171.11.102.1.1.2.14.1.1

A list of information which specifies the port with its traffic
forwarding list.

Indexes

No indexes recorded

Column	Syntax	OID
swL2TrafficSegPort The port number of the logical port.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.14.1.1.1
swL2TrafficSegForwardPorts The port list to which the specific port can forward traffic.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.102.1.1.2.14.1.1.2

A table that contains information about VLAN multicast filter mode.

swL2MulticastFilterModeVlanEntry row .1.3.6.1.4.1.171.11.102.1.1.2.17.1.1

A list of multicast filter mode information for each VLAN.

Indexes

No indexes recorded

Column	Syntax	OID
swL2MulticastFilterVid Indicates VID for each VLAN.	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.17.1.1.1
swL2MulticastFilterVlanMode Specifies multicast filter mode for each VLAN.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.17.1.1.2

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortEntry row .1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1

The table specifies the loopback detection function specified by port.

Indexes

No indexes recorded

Column	Syntax	OID
swL2LoopDetectPortIndex This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module	Integer32	.1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.1
swL2LoopDetectPortState This object indicates the loopback detection function state on the port.	Enumerationr/w	.1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.2
swL2LoopDetectPortLoopVLAN This object indicates the VLAN list that has detected a loopback.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.3
swL2LoopDetectPortLoopStatus This object indicates the port status.	Enumeration	.1.3.6.1.4.1.171.11.102.1.1.2.18.2.1.1.4