DGS-3620-28SC-L3MGMT-MIB Table View

This table contain IP interface information.

swL3IpCtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.2.1.3.1

A list of information about a specific IP interface.

Indexes

swL3IpCtrlInterfaceName

Column	Syntax	OID
swL3IpCtrlInterfaceName This object indicates the name of the IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.1
swL3IpCtrlIfIndex This object uniquely identifies the IP interface number in the swL3IpCtrlTable.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.2
swL3IpCtrlIpAddr The IP address of the interface. This object only can take the value of the unicast IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.3
swL3IpCtrlIpSubnetMask The IP net mask for this interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.4
swL3IpCtrlVlanName This object indicates the IP control entry's VLAN name. The VLAN name in each entry must be unique in the IP Control Table.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.5
swL3IpCtrlProxyArp This object indicates enable/disable of the proxy ARP function for IPv4.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.6
swL3IpCtrlSecondary When this is true(1), the IP address is the secondary IP. When false(2), the IP address is the primary IP.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.7
swL3IpCtrlMode This object indicates the IP operation mode. other(1) - This entry is currently in use but the conditions under which it will remain are determined by each of the following values. bootp(3) - The I…	Enumerationr/w Enumerated Values: 1 other 3 bootp 4 dhcp	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.8
swL3IpCtrlAdminState The state of the IP interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.9
swL3IpCtrlIpv4AdminState The IPv4 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.10
swL3IpCtrlIpv6AdminState The IPv6 admin state of the IP interface. The default state is determined by project. This state will only be effective when the swL3IpCtrlAdminState is enabled.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.12
swL3IpCtrlIpv6LinkLocalAddress The IPv6 link local address for this interface.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.14
swL3IpCtrlIpv6LinkLocalPrefixLen The IPv6 prefix length for this IPv6 link local address.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.15
swL3IpCtrlState This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.16
swL3IpCtrlIpv6LinkLocalAutoState The state of the IPv6 link local auto.	Enumerationr/w Enumerated Values: 1 other 2 enabled 3 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.17
swL3IpCtrlLocalProxyArp This object indicates enable/disable of the local proxy ARP function for IPv4.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.18
swL3IpCtrlIpMtu The MTU is the largest size of the IP datagram which may be transferred using a specific data link connection. The MTU value is a design parameter of a LAN and is a mutually agreed value (i.e. both ends of a link agree …	bytesSNMPv2-SMIInteger32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.19
swL3IpCtrlDhcpv6ClientState The state of the Dhcpv6 Client.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.20
swL3IpCtrlIpDirectedBroadcastState The state of the IP Directed Broadcast.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.21
swL3IpCtrlDhcpv6ClientPDState The state of the Dhcpv6 Client PD.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.24
swL3IpCtrlDhcpv6ClientPDPrefixName This object indicates the name for the DHCPv6 Client PD. If the swL3IpCtrlDhcpv6ClientPDState is disabled, this object will be clear and can't write.	OctetStringr/w Constraints: range: 0-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.25
swL3IpCtrlDhcpv6ClientPDPrefix The IPv6 prefix obtained form delegation router.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.26
swL3IpCtrlDhcpv6ClientPDPrefixLen The IPv6 prefix length for the prefix obtained from delegation router.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.3.1.27

This table contains IPv6 information of an IP interface.

swL3Ipv6CtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.2.1.4.1

A list of IPv6 information about a specific IP interface.

Indexes

swL3Ipv6CtrlInterfaceName

Column	Syntax	OID
swL3Ipv6CtrlInterfaceName This object indicates the name of the IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.1
swL3Ipv6CtrlMaxReassmblySize Maximum Reassembly Size of the IP interface.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.2
swL3Ipv6CtrlNsRetransTimer Neighbor solicitation's retransmit timer. The unit is set in milliseconds.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.3
swL3Ipv6CtrlRaState Neighbor solicited state.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.5
swL3Ipv6CtrlRaMinRtrAdvInterval The minimum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds. It must be no less than 3 seconds and no greater than .75 * MaxRtrAdvInt…	Integer32r/w Constraints: range: 3-1350	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.6
swL3Ipv6CtrlRaMaxRtrAdvInterval The maximum time allowed between sending unsolicited multicast Router Advertisements from the interface. The unit is set in seconds.	Integer32r/w Constraints: range: 4-1800	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.7
swL3Ipv6CtrlRaLifeTime Indicates the lifetime of the router as the default router.	Integer32r/w Constraints: range: 0-9000	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.8
swL3Ipv6CtrlRaReachableTime Indicates the amount of time that a node can consider a neighboring node reachable after receiving a reachability confirmation.	Integer32r/w Constraints: range: 0-3600000	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.9
swL3Ipv6CtrlRaRetransTime Indicates the amount of time between retransmissions of neighbor solicited messages. The unit is set in millisecond.	Unsigned32r/w Constraints: range: 0-4294967295	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.10
swL3Ipv6CtrlRaHopLimit Indicates the default value of the hop limit field in the IPv6 header for packets sent by hosts that receive this RA message.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.11
swL3Ipv6CtrlRaManagedFlag When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an address in the addition to the addresses derived from the stateless address configuration.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.12
swL3Ipv6CtrlRaOtherConfigFlag When enabled, it indicates that hosts receiving this RA must use a stateful address configuration protocol to obtain an on-link address configuration information.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.4.1.13

This table contain IPv6 address information for each IP interface.

swL3Ipv6AddressCtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.2.1.5.1

A list of information about a specific IPv6 address.

Indexes

swL3Ipv6AddressCtrlInterfaceName swL3Ipv6Address swL3Ipv6AddressCtrlPrefixLen

Column	Syntax	OID
swL3Ipv6AddressCtrlInterfaceName This object indicates the name of the IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.1
swL3Ipv6Address Specify the IPv6 address.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.2
swL3Ipv6AddressCtrlPrefixLen Indicates the prefix length of this IPv6 address.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.3
swL3Ipv6AddressCtrlPreferredLifeTime Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains in preferred state. For an infinite valid lifetime, the value can be set to 0xfffffff…	Unsigned32r/w Constraints: range: 0-4294967294	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.4
swL3Ipv6AddressCtrlValidLifeTime Indicates the number of seconds that an address, based on the specified prefix, using the stateless address configuration, remains valid. For an infinite valid lifetime, the value can be set to 0xffffffff.	Unsigned32r/w Constraints: range: 0-4294967294	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.5
swL3Ipv6AddressCtrlOnLinkFlag When enabled, the address implied by the specified prefix is available on the link where the RA message is received.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.6
swL3Ipv6AddressCtrlAutonomousFlag When enabled, the specified prefix will be used to create an autonomous address configuration.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.7
swL3Ipv6AddressCtrlState This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.1.5.1.8

This table contain the information of the IPv6 address which based on DHCPv6 client PD.

swL3Ipv6DHCPv6CPDAddrCtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.2.1.6.1

A list of information about a specific DHCPv6 Client PD IPv6 address.

Indexes

swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName swL3Ipv6DHCPv6CPDAddrCtrlPrefixName swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen

Column	Syntax	OID
swL3Ipv6DHCPv6CPDAddrCtrlInterfaceName This object indicates the name of the IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.6.1.1
swL3Ipv6DHCPv6CPDAddrCtrlPrefixName This object indicates the name of the prefix based on which the IPv6 address will be generate.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.6.1.2
swL3Ipv6DHCPv6CPDAddrCtrlIPv6addr Specify the suffix of the IPv6 address.	IPV6-TCIpv6Address Type Constraints: range: 16	.1.3.6.1.4.1.171.11.118.2.3.2.1.6.1.3
swL3Ipv6DHCPv6CPDAddrCtrlPrefixLen Indicates the prefix length of this IPv6 address.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.2.1.6.1.4
swL3Ipv6DHCPv6CPDAddrCtrlState This variable displays the status of the entry. The status is used for creating and deleting instances of the objects in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.1.6.1.5

This table contains loopback IP interface information.

swL3LoopBackIpCtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.2.1.8.1

A list of information about a specific loopback IP interface.

Indexes

swL3LoopBackIpCtrlInterfaceName

Column	Syntax	OID
swL3LoopBackIpCtrlInterfaceName This object indicates the name of the loopback IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.1
swL3LoopBackIpCtrlIfIndex This object uniquely identifies the loopback IP interface number in the swL3LoopBackIpCtrlTable.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.2
swL3LoopBackIpCtrlIpAddr The IP address of the loopback interface. This object only can take the value of the unicast IP address.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.3
swL3LoopBackIpCtrlIpSubnetMask The IP net mask for this loopback interface.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.4
swL3LoopBackIpCtrlAdminState The state of the loopback IP interface.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.5
swL3LoopBackIpCtrlRowStatus This variable displays the status of the entry. The status is used for creating, modifying, and deleting instances of the objects in this table.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.1.8.1.6

A table that contains forwarding and/or filtering information.
This information is used by the switch in determining how to
propagate the received IP packets.

swL3IpFdbInfoEntry row .1.3.6.1.4.1.171.11.118.2.3.2.2.1.1

Information about a specific IP address for which the bridge
has some forwarding and/or filtering information.

Indexes

swL3IpFdbInfoIpAddr

Column	Syntax	OID
swL3IpFdbInfoIpAddr A IP address for which switch has forwarding and/or filtering information.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.2.1.1.1
swL3IpFdbInfoIpSubnetMask A IP net mask for this interface for which the switch has forwarding and/or filtering information.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.2.1.1.2
swL3IpFdbInfoPort Either the value '0', or the port number of the port on which packets having an IP address equal to the value of the corresponding instance of swL3IpFdbInfoIpAddr has been seen. A value of '0' indicates that the port …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.2.2.1.1.3
swL3IpFdbInfoType The status of this entry.	Enumeration Enumerated Values: 1 other 2 static 3 dynamic	.1.3.6.1.4.1.171.11.118.2.3.2.2.1.1.4

This entity's IP static Routing table.

swL3IpStaticRouteEntry row .1.3.6.1.4.1.171.11.118.2.3.2.5.1

A particular route to a particular destination, under a particular policy.
Once an entry is built,it shouldn't be modified.That is,it just supports
create and delete actions.

Indexes

swL3IpStaticRouteDest swL3IpStaticRouteMask swL3IpStaticRouteNextHop

Column	Syntax	OID
swL3IpStaticRouteDest The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a valu…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.1
swL3IpStaticRouteMask Indicate the mask to be logical-AND with the destination address before being compared to the value in the swL3IpStaticRouteDest field. For those systems that do not support arbitrary subnet masks, an agent c…	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.2
swL3IpStaticRouteBkupState The routing state for this route.The value SHOULD be primary(1), backup(2) or none(3).	Enumerationr/w Enumerated Values: 1 primary 2 backup 3 none	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.3
swL3IpStaticRouteNextHop Specifies the IP address for the next hop router. An IP address of 255.255.255.255 denotes a Null interface as the next hop.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.4
swL3IpStaticRouteMetric Specifies the routing metric for this route. If this metric is not used, its value will be displayed as -1.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.5
swL3IpStaticRouteStatus This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 valid 4 active 5 inActive	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.6
swL3IpStaticRouteWeight Specifies the weight value. Used for the weighted multipath.	Integer32r/w Constraints: range: 0-4	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.7
swL3IpStaticRouteInterfaceName Specifies the name of the IP interface.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.11.118.2.3.2.5.1.8

IP multicast static routing allows you to have multicast paths
diverge from the unicast paths.

swL3IpMcastStaticRouteEntry row .1.3.6.1.4.1.171.11.118.2.3.2.6.1.1

A list of information about IP multicast static routes.

Indexes

swL3IpMcastStaticRouteIpmrouteAddr swL3IpMcastStaticRouteIpmrouteMask

Column	Syntax	OID
swL3IpMcastStaticRouteIpmrouteAddr If the source IP address of the received IP multicast packet matches this Ipmrouteaddress, the RPF network is used to do an RPF check.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.6.1.1.1
swL3IpMcastStaticRouteIpmrouteMask This specifies an IP net Mask for this interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.6.1.1.2
swL3IpMcastStaticRouteRpfAddr If the source IP address of the received IP multicast packet matches the Ipmrouteaddress, the Rpfaddress will be used to check whether the packet received is from a legal interface. If it is set to null, it means that i…	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.2.6.1.1.3
swL3IpMcastStaticRouteRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.6.1.1.4

This entity's IPv4 static Routing tunnel table.

swL3IpStaticRouteTunnelEntry row .1.3.6.1.4.1.171.11.118.2.3.2.7.1

A particular route to a particular destination, under a particular policy.
Once an entry is built, it cannot be modified. That is, it just supports create
and delete actions.

Indexes

swL3IpStaticRouteDest swL3IpStaticRouteMask swL3IpStaticRouteTunnelInterfaceName

Column	Syntax	OID
swL3IpStaticRouteTunnelInterfaceName This object indicates the name of the IP tunnel interface.	OctetString Constraints: range: 0-12	.1.3.6.1.4.1.171.11.118.2.3.2.7.1.1
swL3IpStaticRouteTunnelRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.2.7.1.2

This table displays the current DNS relay static table.

swL3RelayDnsCtrlEntry row .1.3.6.1.4.1.171.11.118.2.3.3.3.6.1

A list of information display the current DNS relay static
table.

Indexes

swL3RelayDnsCtrlDomainName swL3RelayDnsCtrlIpAddr

Column	Syntax	OID
swL3RelayDnsCtrlDomainName The domain name of the entry.	OctetString Constraints: range: 1-32	.1.3.6.1.4.1.171.11.118.2.3.3.3.6.1.1
swL3RelayDnsCtrlIpAddr The IP address of the entry.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.3.3.6.1.2
swL3RelayDnsCtrlState This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 valid	.1.3.6.1.4.1.171.11.118.2.3.3.3.6.1.3

This table displays the current MD5 key table.

swL3Md5Entry row .1.3.6.1.4.1.171.11.118.2.3.4.1

A list of information displays the current MD5 key table.

Indexes

swL3Md5KeyId

Column	Syntax	OID
swL3Md5KeyId The MD5 key ID.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.171.11.118.2.3.4.1.1
swL3Md5Key An MD5 password of up to 16 bytes.	OctetStringr/w Constraints: range: 1-16	.1.3.6.1.4.1.171.11.118.2.3.4.1.2
swL3Md5RowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.4.1.3

Route redistribution allows routers on the network that are 
running different routing protocols to exchange routing 
information. This is accomplished by comparing the routes stored
in the varios routers' routing tables and assigning appropriate
metrics. This information is then exchanged among the various 
routers according to the individual routers current routing 
protocol.

swL3RouteRedistriEntry row .1.3.6.1.4.1.171.11.118.2.3.5.1

A list of information displaying the route redistribution table.

Indexes

swL3RouteRedistriSrcProtocol swL3RouteRedistriDstProtocol

Column	Syntax	OID
swL3RouteRedistriSrcProtocol Allows the selection of the protocol of the source device.	Enumeration Enumerated Values: 1 other 2 rip 3 ospf 4 static 5 local 6 bgp	.1.3.6.1.4.1.171.11.118.2.3.5.1.1
swL3RouteRedistriDstProtocol Allows the selection of the protocol of the destination device.	Enumeration Enumerated Values: 1 other 2 rip 3 ospf 6 bgp	.1.3.6.1.4.1.171.11.118.2.3.5.1.2
swL3RouteRedistriType Allows the selection of one of the methods for calculating the metric value.	Enumerationr/w Enumerated Values: 1 other 2 all 3 type-1 4 type-2 5 internal 6 external 7 inter-E1 8 inter-E2 9 extType1 10 extType2	.1.3.6.1.4.1.171.11.118.2.3.5.1.3
swL3RouteRedistriMetric Allows the entry of an OSPF interface cost. This is analogous to a Hop Count in the RIP routing protocol. The value '0' indicates default value.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.5.1.4
swL3RouteRedistriRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.5.1.5
swL3RouteRedistriRouteMapName This Object just works when the destination protocol is BGP and indicate the route-map working when redistribute the route to BGP.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.171.11.118.2.3.5.1.6

The list of Hosts, and their metrics, that the router will 
advertise as host routes.

swL3OspfHostEntry row .1.3.6.1.4.1.171.11.118.2.3.6.1

A metric to be advertised, for a given type of service, when a
given host is reachable.

Indexes

swL3OspfHostIpAddress swL3OspfHostTOS

Column	Syntax	OID
swL3OspfHostIpAddress The IP Address of the Host.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.6.1.1
swL3OspfHostTOS The Type of Service of the route being configured.	OSPF-MIBTOSType Type Constraints: range: 0..30	.1.3.6.1.4.1.171.11.118.2.3.6.1.2
swL3OspfHostMetric The Metric to be advertised.	OSPF-MIBMetricr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.171.11.118.2.3.6.1.3
swL3OspfHostAreaID The Area the Host Entry is to be found within. By default, the area that a subsuming OSPF interface is in, or 0.0.0.0	OSPF-MIBAreaIDr/w	.1.3.6.1.4.1.171.11.118.2.3.6.1.4
swL3OspfHostStatus This variable displays the status of the entry. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.6.1.5

Information about this router's virtual inter-
faces.

swL3ospfVirtIfEntry row .1.3.6.1.4.1.171.11.118.2.3.7.1

Information about a single Virtual Interface.

Indexes

swL3ospfVirtIfAreaId swL3ospfVirtIfNeighbor

Column	Syntax	OID
swL3ospfVirtIfAreaId The Transit Area that the Virtual Link traverses. By definition, this is not 0.0.0.0	OSPF-MIBAreaID	.1.3.6.1.4.1.171.11.118.2.3.7.1.1
swL3ospfVirtIfNeighbor The Router ID of the Virtual Neighbor.	OSPF-MIBRouterID	.1.3.6.1.4.1.171.11.118.2.3.7.1.2
swL3ospfVirtIfTransitDelay The estimated number of seconds it takes to transmit a link- state update packet over this interface.	OSPF-MIBUpToMaxAge Type Constraints: range: 0..3600	.1.3.6.1.4.1.171.11.118.2.3.7.1.3
swL3ospfVirtIfRetransInterval The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state reque…	OSPF-MIBUpToMaxAge Type Constraints: range: 0..3600	.1.3.6.1.4.1.171.11.118.2.3.7.1.4
swL3ospfVirtIfHelloInterval The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for the virtual neighbor.	OSPF-MIBHelloRanger/w Type Constraints: range: 1..65535	.1.3.6.1.4.1.171.11.118.2.3.7.1.5
swL3ospfVirtIfRtrDeadInterval The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for t…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.118.2.3.7.1.6
swL3ospfVirtIfState OSPF virtual interface states.	Enumeration Enumerated Values: 1 down 4 pointToPoint	.1.3.6.1.4.1.171.11.118.2.3.7.1.7
swL3ospfVirtIfEvents The number of state changes or error events on this Virtual Link	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.7.1.8
swL3ospfVirtIfAuthType The authentication type specified for a virtu- al interface. Additional authentication types may be assigned locally.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.7.1.9
swL3ospfVirtIfAuthKey If Authentication Type is simplePassword, the device will left adjust and zero fill to 8 oc- tets. Note that unauthenticated interfaces need no authentication key, and simple password authen- ticatio…	OctetStringr/w Constraints: range: 0-256	.1.3.6.1.4.1.171.11.118.2.3.7.1.10
swL3ospfVirtIfAuthKeyID The MD5 key ID.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.7.1.11
swL3ospfVirtIfStatus This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.7.1.12

The OSPF Interface Table describes the  inter-
faces from the viewpoint of OSPF.

swL3ospfIfEntry row .1.3.6.1.4.1.171.11.118.2.3.8.1

The OSPF Interface Entry describes one inter-
face from the viewpoint of OSPF.

Indexes

swL3ospfIfIpAddress swL3ospfAddressLessIf

Column	Syntax	OID
swL3ospfIfIpAddress The IP address of this OSPF interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.8.1.1
swL3ospfAddressLessIf For the purpose of easing the instancing of addressed and addressless interfaces; This variable takes the value 0 on interfaces with IP Addresses, and the corresponding value of ifIndex for interfaces havin…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.8.1.2
swL3ospfIfAreaId A 32-bit integer uniquely identifying the area to which the interface connects. Area ID 0.0.0.0 is used for the OSPF backbone.	OSPF-MIBAreaIDr/w	.1.3.6.1.4.1.171.11.118.2.3.8.1.3
swL3ospfIfType The OSPF interface type. By way of a default, this field may be intuited from the corresponding value of ifType. Broad- cast LANs, such as Ethernet and IEEE 802.5, take the value 'broadcast', X.25…	Enumerationr/w Enumerated Values: 1 broadcast 2 nbma 3 pointToPoint 5 pointToMultipoint	.1.3.6.1.4.1.171.11.118.2.3.8.1.4
swL3ospfIfAdminStat The OSPF interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is extern…	OSPF-MIBStatusr/w Type Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.118.2.3.8.1.5
swL3ospfIfRtrPriority The priority of this interface. Used in multi-access networks, this field is used in the designated router election algorithm. The value 0 signifies that the router is not eligi- ble to become the designate…	OSPF-MIBDesignatedRouterPriorityr/w Type Constraints: range: 0..255	.1.3.6.1.4.1.171.11.118.2.3.8.1.6
swL3ospfIfTransitDelay The estimated number of seconds it takes to transmit a link state update packet over this interface.	OSPF-MIBUpToMaxAge Type Constraints: range: 0..3600	.1.3.6.1.4.1.171.11.118.2.3.8.1.7
swL3ospfIfRetransInterval The number of seconds between link-state ad- vertisement retransmissions, for adjacencies belonging to this interface. This value is also used when retransmitting database descrip- tion and link-state request …	OSPF-MIBUpToMaxAge Type Constraints: range: 0..3600	.1.3.6.1.4.1.171.11.118.2.3.8.1.8
swL3ospfIfHelloInterval The length of time, in seconds, between the Hello packets that the router sends on the in- terface. This value must be the same for all routers attached to a common network.	OSPF-MIBHelloRanger/w Type Constraints: range: 1..65535	.1.3.6.1.4.1.171.11.118.2.3.8.1.9
swL3ospfIfRtrDeadInterval The number of seconds that a router's Hello packets have not been seen before it's neigh- bors declare the router down. This should be some multiple of the Hello interval. This value must be the same for a…	OSPF-MIBPositiveIntegerr/w Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.171.11.118.2.3.8.1.10
swL3ospfIfPollInterval The larger time interval, in seconds, between the Hello packets sent to an inactive non- broadcast multi- access neighbor.	OSPF-MIBPositiveInteger Type Constraints: range: 0..2147483647	.1.3.6.1.4.1.171.11.118.2.3.8.1.11
swL3ospfIfState The OSPF Interface State.	Enumeration Enumerated Values: 1 down 2 loopback 3 waiting 4 pointToPoint 5 designatedRouter 6 backupDesignatedRouter 7 otherDesignatedRouter	.1.3.6.1.4.1.171.11.118.2.3.8.1.12
swL3ospfIfDesignatedRouter The IP Address of the Designated Router.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.8.1.13
swL3ospfIfBackupDesignatedRouter The IP Address of the Backup Designated Router.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.8.1.14
swL3ospfIfEvents The number of times this OSPF interface has changed its state, or an error has occurred.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.8.1.15
swL3ospfIfMulticastForwarding The way multicasts should forwarded on this interface; not forwarded, forwarded as data link multicasts, or forwarded as data link uni- casts. Data link multicasting is not meaning- ful on point to point and NB…	Enumeration Enumerated Values: 1 blocked 2 multicast 3 unicast	.1.3.6.1.4.1.171.11.118.2.3.8.1.16
swL3ospfIfDemand Indicates whether Demand OSPF procedures (hel- lo supression to FULL neighbors and setting the DoNotAge flag on proogated LSAs) should be per- formed on this interface.	SNMPv2-TCTruthValue Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.11.118.2.3.8.1.17
swL3ospfIfAuthType The authentication type specified for an in- terface. Additional authentication types may be assigned locally.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.8.1.18
swL3ospfIfAuthKey The Authentication Key. If the Area's Author- ization Type is simplePassword, and the key length is shorter than 8 octets, the agent will left adjust and zero fill to 8 octets. Note that unauthentica…	OctetStringr/w Constraints: range: 0-256	.1.3.6.1.4.1.171.11.118.2.3.8.1.19
swL3ospfIfAuthKeyID The MD5 key ID.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.8.1.20
swL3ospfIfPassiveMode Assign the designated entry to be a passive interface.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.118.2.3.8.1.21
swL3ospfIfMetric The Metric to be advertised.	OSPF-MIBMetricr/w Type Constraints: range: 0..65535	.1.3.6.1.4.1.171.11.118.2.3.8.1.23
swL3ospfIfDistributeListInType The type of route filter for distribute list in.	Enumerationr/w Enumerated Values: 1 none 2 access_list	.1.3.6.1.4.1.171.11.118.2.3.8.1.24
swL3ospfIfDistributeListInName The name of route filter for distribute list in.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.171.11.118.2.3.8.1.25

Information describing the configured  parame-
ters  and cumulative statistics of the router's
attached areas.

swL3ospfAreaEntry row .1.3.6.1.4.1.171.11.118.2.3.10.1

Information describing the configured parame-
ters and cumulative statistics of one of the
router's attached areas.

Indexes

swL3ospfAreaId

Column	Syntax	OID
swL3ospfAreaId A 32-bit integer uniquely identifying an area. Area ID 0.0.0.0 is used for the OSPF backbone.	OSPF-MIBAreaID	.1.3.6.1.4.1.171.11.118.2.3.10.1.1
swL3ospfAreaTypeobsolete The type specified for an area.	Enumerationr/w Enumerated Values: 1 normal 2 stub 3 nssa	.1.3.6.1.4.1.171.11.118.2.3.10.1.2
swL3ospfAreaSummaryState Whether the summary LSA is effective for this area.	Enumerationr/w Enumerated Values: 1 none 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.118.2.3.10.1.3
swL3ospfAreaMetric Enter the metric (1 - 65535; 0 for auto cost) of this area.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.10.1.4
swL3ospfAreaTranslateState .	Enumerationr/w Enumerated Values: 1 none 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.118.2.3.10.1.5
swL3ospfAreaStatus This variable displays the status of the en- try. Setting it to 'invalid' has the effect of rendering it inoperative. The internal effect (row removal) is implementation dependent.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.10.1.6

The (conceptual) table listing the router's multicast-
capable interfaces.

swL3dvmrpInterfaceEntry row .1.3.6.1.4.1.171.11.118.2.3.12.1

An entry (conceptual row) in the dvmrpInterfaceTable. This
row augments ipMRouteInterfaceEntry in the IP Multicast MIB,
where the threshold object resides.

Indexes

swL3dvmrpInterfaceIfIndex

Column	Syntax	OID
swL3dvmrpInterfaceIfIndex The ifIndex value of the interface for which DVMRP is enabled.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.12.1.1
swL3dvmrpInterfaceLocalAddress The IP address this system will use as a source address on this interface. On unnumbered interfaces, it must be the same value as dvmrpInterfaceLocalAddress for some interface on the system.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.12.1.2
swL3dvmrpInterfaceMetric The distance metric for this interface which is used to calculate distance vectors.	Integer32r/w Constraints: range: 1-31	.1.3.6.1.4.1.171.11.118.2.3.12.1.3
swL3dvmrpInterfaceProbe Probe distribution interval.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.118.2.3.12.1.4
swL3dvmrpInterfaceNbrTimeout Used to set the timer before neighbors are timed out.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.118.2.3.12.1.5
swL3dvmrpInterfaceStatus The status of this entry. Creating the entry enables DVMRP on the virtual interface; destroying the entry or setting it to notInService disables DVMRP on the virtual interface.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.12.1.6
swL3dvmrpInterfaceRcvBadPkts The number of DVMRP packets received on the interface by the DVMRP process which were subsequently discarded as invalid (e.g. invalid packet format, or a route report from an unknown neighbor).	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.12.1.7
swL3dvmrpInterfaceRcvBadRoutes The number of routes, in valid DVMRP packets, which were ignored because the entry was invalid.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.12.1.8

The OSPF Process's Link State Database.

swL3OspfInternalLsdbEntry row .1.3.6.1.4.1.171.11.118.2.3.13.1.1

A single Link State Advertisement.

Indexes

swL3OspfInternalLsdbAreaId swL3OspfInternalLsdbType swL3OspfInternalLsdbLsid swL3OspfInternalLsdbRouterId

Column	Syntax	OID
swL3OspfInternalLsdbAreaId The 32 bit identifier of the Area from which the LSA was received.	OSPF-MIBAreaID	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.1
swL3OspfInternalLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 1 routerLink 2 networkLink 3 summaryLink 4 asSummaryLink 5 asExternalLink 6 multicastLink 7 nssaExternalLink	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.2
swL3OspfInternalLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.3
swL3OspfInternalLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.4
swL3OspfInternalLsdbMetric Enter the metric (1 - 65535; 0 for auto cost) of this area.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.5
swL3OspfInternalLsdbSequenceNo The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number t…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.6
swL3OspfInternalLsdbAge This field is the age of the link state adver- tisement in seconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.7
swL3OspfInternalLsdbChecksum This field is the checksum of the complete contents of the advertisement, excepting the age field. The age field is excepted so that an advertisement's age can be incremented without updating the checks…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.13.1.1.8

The OSPF Process's Links State Database.

swL3OspfExternalLsdbEntry row .1.3.6.1.4.1.171.11.118.2.3.13.2.1

A single Link State Advertisement.

Indexes

swL3OspfExternalLsdbType swL3OspfExternalLsdbLsid swL3OspfExternalLsdbRouterId

Column	Syntax	OID
swL3OspfExternalLsdbType The type of the link state advertisement. Each link state type has a separate advertise- ment format.	Enumeration Enumerated Values: 5 asExternalLink 7 nssaExternalLink	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.1
swL3OspfExternalLsdbLsid The Link State ID is an LS Type Specific field containing either a Router ID or an IP Address; it identifies the piece of the routing domain that is being described by the advertisement.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.2
swL3OspfExternalLsdbRouterId The 32 bit number that uniquely identifies the originating router in the Autonomous System.	OSPF-MIBRouterID	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.3
swL3OspfExternalLsdbMetric Enter the metric (1 - 65535; 0 for auto cost) of this area.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.4
swL3OspfExternalLsdbMetricType Enter the metric type of this area.	Enumeration Enumerated Values: 0 unrecognized 1 type-1 2 type-2	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.5
swL3OspfExternalLsdbSequenceNo The sequence number field is a signed 32-bit integer. It is used to detect old and dupli- cate link state advertisements. The space of sequence numbers is linearly ordered. The larger the sequence number t…	OctetString Constraints: range: 4-4	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.6
swL3OspfExternalLsdbAge This field is the age of the link state adver- tisement in seconds.	SNMPv2-SMIUnsigned32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.7
swL3OspfExternalLsdbChecksum This field is the checksum of the complete contents of the advertisement, except the age field. The age field is the exception so that an advertisement's age can be incremented without updating the checksum. Th…	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.8
swL3OspfExternalLsdbForwardingAddress This field is the forwarding address.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.9
swL3OspfExternalLsdbRouteTag This field is the route tag.	OctetString	.1.3.6.1.4.1.171.11.118.2.3.13.2.1.10

Operations table for a VRRP router which consists of a
sequence (i.e., one or more conceptual rows) of
'swL3vrrpOperEntry' items.

swL3VrrpOperEntry row .1.3.6.1.4.1.171.11.118.2.3.14.1.1

An entry in the vrrpOperTable containing the operational
characteristics of a virtual router. On a VRRP router,
a given virtual router is identified by a combination
of the IF index and VRID.

Rows in the ta…

Indexes

swL3VrrpOperIfIndex swL3VrrpOperVrId

Column	Syntax	OID
swL3VrrpOperIfIndex The ifIndex value of the interface for which VRRP is enabled.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.1
swL3VrrpOperVrId This object contains the Virtual Router Identifier (VRID).	VrId Type Constraints: range: 1..255	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.2
swL3VrrpOperVirtualMacAddr The virtual MAC address of the virtual router. Although this object can be derived from the 'swL3VrrpOperVrId' object, it is defined so that it is easily obtainable by a management application and can be included in VRR…	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.3
swL3VrrpOperState The current state of the virtual router. This object has three defined values: - `initialize', which indicates that all the virtual router is waiting for a startup event. - `backup'…	Enumeration Enumerated Values: 1 initialize 2 backup 3 master	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.4
swL3VrrpOperAdminState This object will enable/disable the virtual router function. Setting the value to `up', will transition the state of the virtual router from `initialize' to `backup' or `master', depending on the value of `swL3VrrpOperP…	Enumerationr/w Enumerated Values: 1 up 2 down	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.5
swL3VrrpOperPriority This object specifies the priority to be used for the virtual router master election process. Higher values imply higher priority. A priority of '0', although not settable, is sent by the master router to…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.6
swL3VrrpOperMasterIpAddr The master router's real (primary) IP address. This is the IP address listed as the source in VRRP advertisement last received by this virtual router.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.7
swL3VrrpOperCriticalIpAddr In the case where there is more than one IP address for a given `ifIndex', this object is used to specify the IP address that will become the `swL3VrrpOperMasterIpAddr', should the virtual router transition from backup …	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.8
swL3VrrpOperCheckCriticalIpState Critical IP state.	Enumerationr/w Enumerated Values: 0 other 1 disabled 2 enabled	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.9
swL3VrrpOperAuthType Authentication type used for VRRP protocol exchanges between virtual routers. This value of this object is the same for a given ifIndex. New enumerations to this list can only be added via a new RFC on th…	Enumerationr/w Enumerated Values: 1 noAuthentication 2 simpleTextPassword 3 ipAuthenticationHeader	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.10
swL3VrrpOperAuthKey The Authentication Key. This object is set according to the value of the 'swL3VrrpOperAuthType' object ('simpleTextPassword' or 'ipAuthenticationHeader'). If the length of the value is less than 16 octets, the agent wil…	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.11
swL3VrrpOperAdvertisementInterval The time interval, in seconds, between sending advertisement messages. Only the master router sends VRRP advertisements.	secondsInteger32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.12
swL3VrrpOperPreemptMode Controls whether a higher priority virtual router will preempt a lower priority master.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.13
swL3VrrpOperVirtualRouterUpTime This is the value of the `sysUpTime' object when this virtual router (i.e., the `swL3VrrpOperState') transitioned out of `initialized'.	SNMPv2-TCTimeStamp Based On: SNMPv2-SMITimeTicks Description: The value of the sysUpTime object at which a specific occurrence happened. The specific occurrence must be defined in the description of any object defined using this type. If sysUpTime is reset t…	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.14
swL3VrrpOperVirtualIpAddr The assigned IP addresses that a virtual router is responsible for backing up.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.15
swL3VrrpOperRowStatus The row status variable, used in accordance to installation and removal conventions for conceptual rows. The rowstatus of a currently active row in the vrrpOperTable is constrained by the operational state of the corres…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.14.1.1.16

The list of inbound route filter on RIP interfaces.

swL3RIPInboundRouteFilterEntry row .1.3.6.1.4.1.171.11.118.2.3.19.1

The information of inbound route filter on RIP interfaces.

Indexes

swL3RIPInboundRouteFilterIfIpAddress

Column	Syntax	OID
swL3RIPInboundRouteFilterIfIpAddress The IP Address of the RIP interface.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.118.2.3.19.1.1
swL3RIPInboundRouteFilterType The type of inbound route filter for the RIP interface.	Enumerationr/w Enumerated Values: 1 none 2 access_list	.1.3.6.1.4.1.171.11.118.2.3.19.1.2
swL3RIPInboundRouteFilterName The name of inbound route filter for the RIP interface.	OctetStringr/w Constraints: range: 0-16	.1.3.6.1.4.1.171.11.118.2.3.19.1.3

IPv6 Route redistribution allows routers on the network that are 
running different routing protocols to exchange routing 
information. This is accomplished by comparing the routes stored
in the varios routers' routing tables and assigning appropriate
metrics. This information is then exchanged among the various 
routers according to the individual routers current routing 
protocol.

swL3Route6RedistriEntry row .1.3.6.1.4.1.171.11.118.2.3.20.1

A list of information displaying the IPv6 route redistribution table.

Indexes

swL3Route6RedistriSrcProtocol swL3Route6RedistriDstProtocol

Column	Syntax	OID
swL3Route6RedistriSrcProtocol Allows the selection of the protocol of the source device.	Enumeration Enumerated Values: 1 local 2 static 3 ripng 4 ospfv3	.1.3.6.1.4.1.171.11.118.2.3.20.1.1
swL3Route6RedistriDstProtocol Allows the selection of the protocol of the destination device.	Enumeration Enumerated Values: 1 ripng 2 ospfv3	.1.3.6.1.4.1.171.11.118.2.3.20.1.2
swL3Route6RedistriType Allows the selection of one of the methods for calculating the metric value.	Enumerationr/w Enumerated Values: 1 type-1 2 type-2 3 all	.1.3.6.1.4.1.171.11.118.2.3.20.1.3
swL3Route6RedistriMetric Allows the entry of an OSPFv3 interface cost. This is analogous to a Hop Count in the RIPng routing protocol. The value '0' indicates default value.	SNMPv2-SMIUnsigned32r/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.171.11.118.2.3.20.1.4
swL3Route6RedistriRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.118.2.3.20.1.5