DES3828P-L2MGMT-MIB Table View

A list of the temperature.

swDevInfoPowerEntry row .1.3.6.1.4.1.171.11.69.3.2.1.1.8.1

An entry for Power information.

Indexes

swDevInfoPowerUnitIndex swDevInfoPowerID

Column	Syntax	OID
swDevInfoPowerUnitIndex Indicates the ID of the unit in the System	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.1.1.8.1.1
swDevInfoPowerID Indicates ID of the power	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.1.1.8.1.2
swDevInfoPowerStatus Indicates status of the power	Enumeration Enumerated Values: 0 other 1 lowVoltage 2 overCurrent 3 working 4 fail 5 connect 6 disconnect	.1.3.6.1.4.1.171.11.69.3.2.1.1.8.1.3

A table containing the advertisement state for each
VLAN configured into the device by (local or
network) management.

swL2VlanAdvertisementEntry row .1.3.6.1.4.1.171.11.69.3.2.3.1.1

Advertisement state for each VLAN configured
in the device.

Indexes

swL2VlanIndex

Column	Syntax	OID
swL2VlanIndex The VLAN-ID or other identifier referring to this VLAN.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.11.69.3.2.3.1.1.1
swL2VlanName An administratively assigned string, which may be used to identify the VLAN.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.171.11.69.3.2.3.1.1.2
swL2VlanAdvertiseState This object indicates the advertised status of this VLAN entry.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.3.1.1.3

A table that contains information about every port.

swL2PortInfoEntry row .1.3.6.1.4.1.171.11.69.3.2.4.1.1

A list of information for each port of the device.

Indexes

swL2PortInfoPortIndex

Column	Syntax	OID
swL2PortInfoPortIndexobsolete This object indicates the module's port number.(1..Max port number in the module).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.1
swL2PortInfoUnitIndexobsolete Indicates ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.2
swL2PortInfoTypeobsolete This object indicates the connector type of this port.	Enumeration Enumerated Values: 1 portType-100Base-TX 2 portType-100Base-FX 3 portType-100Base-FL 4 portType-1000Base-TX 5 portType-1000Base-SX 6 portType-1000Base-LX 7 none	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.3
swL2PortInfoLinkStatusobsolete This object indicates the port link status.	Enumeration Enumerated Values: 1 other 2 link-pass 3 link-fail	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.4
swL2PortInfoNwayStatusobsolete This object indicates the port speed and duplex mode.	Enumeration Enumerated Values: 1 other 2 auto 3 half-10Mbps 4 full-10Mbps 5 half-100Mbps 6 full-100Mbps 7 half-1Gigabps 8 full-1Gigabps	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.5
swL2PortInfoModuleTypeobsolete This object indicates the module type of this port.	Enumeration Enumerated Values: 0 none 1 moduleType-COMBO 2 moduleType-1000T 3 moduleType-BaseModule	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.6
swL2PortInfoErrorDisabledobsolete This object indicates the blocking type of this port.	Enumeration Enumerated Values: 0 none 1 storm 2 lbd 3 unknow	.1.3.6.1.4.1.171.11.69.3.2.4.1.1.7

A table that contains control information about every port.

swL2PortCtrlEntry row .1.3.6.1.4.1.171.11.69.3.2.4.2.1

A list of control information for each port of the device.

Indexes

swL2PortCtrlPortIndex

Column	Syntax	OID
swL2PortCtrlPortIndexobsolete This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.1
swL2PortCtrlUnitIndexobsolete Indicates the ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.2
swL2PortCtrlAdminStateobsolete This object decides whether the port is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.3
swL2PortCtrlNwayStateobsolete Choose the port speed, duplex mode, and N-Way function mode.	Enumerationr/w Enumerated Values: 1 other 2 nway-enabled 3 nway-disabled-10Mbps-Half 4 nway-disabled-10Mbps-Full 5 nway-disabled-100Mbps-Half 6 nway-disabled-100Mbps-Full 7 nway-disabled-1Gigabps-Half 8 nway-disabled-1Gigabps-Full	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.4
swL2PortCtrlFlowCtrlStateobsolete The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and…	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.5
swL2PortCtrlLockStateobsolete This object decides whether the port is locked or not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.6
swL2PortCtrlMACNotifyStateobsolete This object decides whether MAC notification is enabled or not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.2.1.7

A table that contains information about every port.

swL2PortInformationEntry row .1.3.6.1.4.1.171.11.69.3.2.4.4.1

A list of information for each port of the device.

Indexes

swL2PortInformationPortIndex swL2PortInformationMediumType

Column	Syntax	OID
swL2PortInformationPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.1
swL2PortInformationMediumType Indicates medium type of the port number.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.2
swL2PortInformationUnitID Indicates ID of the unit in the system	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.3
swL2PortInformationType This object indicates the connector type of this port.	Enumeration Enumerated Values: 1 portType-100Base-TX 2 portType-100Base-FX 3 portType-100Base-FL 4 portType-1000Base-TX 5 portType-1000Base-SX 6 portType-1000Base-LX 7 portType-1000Base-SX-GBIC 8 portType-1000Base-LX-GBIC 9 portType-1000Base-TX-GBIC 10 portType-1000Base-1394 11 portType-1000Base-TX-GBIC-COMBO 12 portType-1000Base-none-GBIC 13 portType-1000Base-SX-MGBIC 14 portType-1000Base-LX-MGBIC 15 portType-1000Base-TX-MGBIC 16 portType-1000Base-none-MGBIC 17 portType-SIO 18 portType-10G 19 portType-10G-xenpak-1310nm 20 portType-10G-xenpak-850nm 21 portType-10G-xenpak-empty 22 portType-10G-xfp-1310nm 23 portType-10G-xfp-850nm 24 portType-10G-xfp-empty 25 portType-none	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.4
swL2PortInformationLinkStatus This object indicates the port link status.	Enumeration Enumerated Values: 1 other 2 link-pass 3 link-fail	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.5
swL2PortInformationNwayStatus This object indicates the port speed and duplex mode.	Enumeration Enumerated Values: 0 other 1 empty 2 link-down 3 half-10Mbps 4 full-10Mbps 5 half-100Mbps 6 full-100Mbps 7 half-1Gigabps 8 full-1Gigabps 9 full-10Gigabps	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.6
swL2PortInformationModuleType This object indicates the module type of this port.	Enumeration Enumerated Values: 0 none 1 moduleType-COMBO 2 moduleType-1394 3 moduleType-1000T 4 moduleType-MGBIC 5 moduleType-1P-SC-SX 6 moduleType-2P-SC-SX 7 moduleType-1P-SC-LX 8 moduleType-2P-SC-LX 9 moduleType-1P-TX 10 moduleType-2P-TX 11 moduleType-1P-MTRJ-SX 12 moduleType-2P-MTRJ-SX 13 moduleType-1P-MTRJ-LX 14 moduleType-2P-MTRJ-LX 15 moduleType-1P-GBIC 16 moduleType-2P-GBIC 17 moduleType-1P-GBIC-1P-TX 18 moduleType-1P-GBIC-1P-STACK 19 moduleType-2P-STACK 20 moduleType-2P-100FX 21 moduleType-1P-100FX 22 moduleType-2P-100FX-NEW 23 moduleType-1P-100FL 24 moduleType-2P-100FL 25 moduleType-2P-100TX 26 moduleType-BaseModule-24PORT	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.7
swL2PortInformationErrorDisabled This object indicates the blocking type of this port.	Enumeration Enumerated Values: 0 none 1 storm 2 lbd 3 unknow	.1.3.6.1.4.1.171.11.69.3.2.4.4.1.8

A table that contains control information about every port.

swL2PortControlEntry row .1.3.6.1.4.1.171.11.69.3.2.4.5.1

A list of control information for each port of the device.

Indexes

swL2PortControlPortIndex swL2PortControlMediumType

Column	Syntax	OID
swL2PortControlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.1
swL2PortControlMediumType Indicates the medium type of the port number.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.2
swL2PortControlUnitIndex Indicates ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.3
swL2PortControlAdminState This object decides if the port is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.4
swL2PortControlNwayState Choose the port speed, duplex mode, and N-Way function mode.	Enumerationr/w Enumerated Values: 1 other 2 nway-enabled 3 nway-disabled-10Mbps-Half 4 nway-disabled-10Mbps-Full 5 nway-disabled-100Mbps-Half 6 nway-disabled-100Mbps-Full 7 nway-disabled-1Gigabps-Half 8 nway-disabled-1Gigabps-Full 9 nway-disabled-1Gigabps-Full-master 10 nway-disabled-1Gigabps-Full-slave	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.5
swL2PortControlFlowCtrlState The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames and…	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.6
swL2PortControlLearningState This object decides whether the port is locked or not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.7
swL2PortControlMACNotifyState This object sets each port's MAC notification state.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.8
swL2PortControlMulticastfilter This object controls the multicast port filtering mode for a specified port.	Enumerationr/w Enumerated Values: 0 other 1 forward-all-groups 2 forward-unregistered-groups 3 filter-unregistered-groups	.1.3.6.1.4.1.171.11.69.3.2.4.5.1.9

.

swL2QOSBandwidthControlEntry row .1.3.6.1.4.1.171.11.69.3.2.6.1.1

A list of information contained in swL2QOSBandwidthControlTable.

Indexes

swL2QOSBandwidthPortIndex

Column	Syntax	OID
swL2QOSBandwidthPortIndex Indicates the port.	Integer32 Constraints: range: 1-650	.1.3.6.1.4.1.171.11.69.3.2.6.1.1.1
swL2QOSBandwidthRxRate Indicates the RX Rate(kbit/sec) of the specifed port. Value 0 means no limit.	Integer32r/w Constraints: range: 0-1000000	.1.3.6.1.4.1.171.11.69.3.2.6.1.1.2
swL2QOSBandwidthTxRate Indicates the TX Rate(kbit/sec) of the specifed port. Value 0 means no limit.	Integer32r/w Constraints: range: 0-1000000	.1.3.6.1.4.1.171.11.69.3.2.6.1.1.3
swL2QOSBandwidthRadiusRxRate The Rx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Rx Rate.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.69.3.2.6.1.1.4
swL2QOSBandwidthRadiusTxRate The Tx Rate value comes from the RADIUS server, If an 802.1X port is authenticated, this value will overwrite the locally configured Tx Rate.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.69.3.2.6.1.1.5

.

swL2QOSSchedulingEntry row .1.3.6.1.4.1.171.11.69.3.2.6.2.1

A list of information contained in swL2QOSSchedulingTable.

Indexes

swL2QOSSchedulingClassIndex

Column	Syntax	OID
swL2QOSSchedulingClassIndex Indicates the hardware queue number.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.11.69.3.2.6.2.1.1
swL2QOSSchedulingMaxPkts Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 255 can be specified.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.171.11.69.3.2.6.2.1.2

.

swL2QOS8021pUserPriorityEntry row .1.3.6.1.4.1.171.11.69.3.2.6.3.1

A list of information contained in swL2QOS8021pUserPriorityTable.

Indexes

swL2QOS8021pUserPriorityIndex

Column	Syntax	OID
swL2QOS8021pUserPriorityIndex The 802.1p user priority .	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.11.69.3.2.6.3.1.1
swL2QOS8021pUserPriorityClass The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.171.11.69.3.2.6.3.1.2

.

swL2QOS8021pDefaultPriorityEntry row .1.3.6.1.4.1.171.11.69.3.2.6.4.1

A list of information contained in swL2QOS8021pDefaultPriorityTable.

Indexes

swL2QOS8021pDefaultPriorityIndex

Column	Syntax	OID
swL2QOS8021pDefaultPriorityIndex Indicates the port number.	Integer32 Constraints: range: 1-650	.1.3.6.1.4.1.171.11.69.3.2.6.4.1.1
swL2QOS8021pDefaultPriority The priority value to assign to untagged packets received by the switch ports on the switch.	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.171.11.69.3.2.6.4.1.2
swL2QOS8021pRadiusPriority Indicates the value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.69.3.2.6.4.1.3

This table specifies which ports are grouped as a set of ports(up to 8)
into a single logical link.

swL2TrunkCtrlEntry row .1.3.6.1.4.1.171.11.69.3.2.8.3.1

A list of information specifies which ports are grouped as a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkIndex

Column	Syntax	OID
swL2TrunkIndex The index of logical port trunk. The trunk group number depends on the existence of the unit and module.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.1
swL2TrunkName The name of logical port trunk.	OctetStringr/w Constraints: range: 0-12	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.2
swL2TrunkMasterPort The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be the same as the master p…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.3
swL2TrunkMember Indicates how many ports are included in this Trunk. The trunk port number depends on the existence of module. The maximum number of ports is 8 for one trunks.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.4
swL2TrunkFloodingPort The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.5
swL2TrunkType This object indicates the type of the trunk group. static : is static trunk group lacp : is LACP trunk group .	Enumerationr/w Enumerated Values: 1 other 2 static 3 lacp	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.6
swL2TrunkState This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.69.3.2.8.3.1.7

This table controls the VLAN's IGMP function. Its scale depends
on the current VLAN state (swL2VlanInfoStatus). If VLAN is in disabled
mode, there is only one entry in the table, with index 1. If
VLAN is in Port-Base or 802.1q mode, the number of entries can
be up to 12, with an index range from 1 to 12.

swL2IGMPCtrlEntry row .1.3.6.1.4.1.171.11.69.3.2.10.3.1

The entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled.

Indexes

swL2IGMPCtrlVid

Column	Syntax	OID
swL2IGMPCtrlVid This object indicates the IGMP control entry's VLAN ID. If VLAN is disabled, the VID is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the VID is arranged from 1 to 12, fixed form. If …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.1
swL2IGMPQueryInterval The frequency at which the IGMP Host-Query packets are transmitted on this switch.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.2
swL2IGMPMaxResponseTime The maximum query response time on this switch.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.3
swL2IGMPRobustness The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to have a high loss, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet los…	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.4
swL2IGMPLastMemberQueryInterval The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.5
swL2IGMPHostTimeout The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer has expired. Please referen…	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.6
swL2IGMPRouteTimeout The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.7
swL2IGMPLeaveTimer When a query receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.	Integer32r/w Constraints: range: 0-16711450	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.8
swL2IGMPQueryState This object decides if the IGMP query is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.9
swL2IGMPCurrentState This object indicates the current IGMP query state.	Enumeration Enumerated Values: 1 other 2 querier 3 non-querier	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.10
swL2IGMPCtrlState This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different for each of the following values. disable(2…	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.11
swL2IGMPFastLeaveState This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following value…	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.171.11.69.3.2.10.3.1.12

The table contains the current number of IGMP query packets which
have been captured by this device, as well as the IGMP query packets
sent by the device.

swL2IGMPQueryInfoEntry row .1.3.6.1.4.1.171.11.69.3.2.10.4.1

Information about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entires are all enabled.

Indexes

swL2IGMPInfoVid

Column	Syntax	OID
swL2IGMPInfoVid This object indicates the VID of the associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of the IGMP control table (swL2IGMPCtrlTable).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.4.1.1
swL2IGMPInfoQueryCount This object indicates the number of query packets received since the IGMP function has been enabled, on a per-VLAN basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.4.1.2
swL2IGMPInfoTxQueryCount This object indicates the send count of IGMP query messages, on a per-VLAN basis. In case of the IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increments this object by 1.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.4.1.3

The table containing current IGMP information which have been captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entries are all enabled. Note
that the priority of IGMP table entries is lower than the Filtering
Table, i.e. if there is a table hash collision between the
entries of the IGMP Table and the Filtering Table inside the switch H/W
address table, the Filtering Table entry will overwrite the
colliding entry of the IGMP Table. See swL2FilterMgmt description
also.

swL2IGMPInfoEntry row .1.3.6.1.4.1.171.11.69.3.2.10.5.1

Information about current IGMP information which was captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entries are all enabled.

Indexes

swL2IGMPVid swL2IGMPGroupIpAddr

Column	Syntax	OID
swL2IGMPVid This object indicates the VID of individual IGMP table entries. It shows the VID of IGMP report information captured on the network.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.5.1.1
swL2IGMPGroupIpAddr This object identifies group ip address which have been captured from the IGMP packet, on a per-Vlan basis.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.69.3.2.10.5.1.2
swL2IGMPMacAddr This object identifies mac addresses which correspond to swL2IGMPGroupIpAddr, on a per-Vlan basis.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.11.69.3.2.10.5.1.3
swL2IGMPPortMap This object indicates which ports belong to the same multicast group, on a per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered port…	PortList Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.5.1.4
swL2IGMPIpGroupReportCount This object indicates how many report packets were received by the device corresponding with this entry where the IGMP function is enabled, on a per-Vlan basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.10.5.1.5

The information of the IGMP snooping multicast VLAN table.

swL2IGMPMulticastVlanEntry row .1.3.6.1.4.1.171.11.69.3.2.10.6.1

The entry of swL2IGMPMulticastVlanTable.

Indexes

swL2IGMPMulticastVlanid

Column	Syntax	OID
swL2IGMPMulticastVlanid This object indicates the VLAN id of the IGMP snooping multicast VLAN entry.	Integer32 Constraints: range: 2-4094	.1.3.6.1.4.1.171.11.69.3.2.10.6.1.1
swL2IGMPMulticastVlanName This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.11.69.3.2.10.6.1.2
swL2IGMPMulticastVlanSourcePort This object indicates the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry and the IGMP control messages received from the member ports would be f…	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.6.1.3
swL2IGMPMulticastVlanMemberPort This object indicates the portlist of the member ports of IGMP snooping multicast VLAN. The source ports will be set to untag ports of the vlan entry and the IGMP control messages received from the member ports would be…	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.6.1.4
swL2IGMPMulticastVlanRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.69.3.2.10.6.1.5

The information of the router port table.

swL2IGMPRouterPortEntry row .1.3.6.1.4.1.171.11.69.3.2.10.7.1

The entry of swL2IGMPRouterPortTable.

Indexes

swL2IGMPRouterPortVlanid

Column	Syntax	OID
swL2IGMPRouterPortVlanid This object indicates the VLAN id of the router port entry.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.11.69.3.2.10.7.1.1
swL2IGMPRouterPortVlanName This object indicates the VLAN name of the router port entry.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.171.11.69.3.2.10.7.1.2
swL2IGMPRouterPortStaticPortList This object indicates the static portlist of the router port entry.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.7.1.3
swL2IGMPRouterPortDynamicPortList This object indicates the dynamic portlist of the router port entry.	PortList Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.7.1.4
swL2IGMPRouterPortForbiddenPortList This object indicates the forbidden portlist of the router port entry.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.10.7.1.5

This table specifies that the port can just forward traffic to the
specific port list.

swL2TrafficSegEntry row .1.3.6.1.4.1.171.11.69.3.2.13.1.1

A list of information specifying the port with its traffic
forward list.

Indexes

swL2TrafficSegPort

Column	Syntax	OID
swL2TrafficSegPort The port number of the logical port.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.13.1.1.1
swL2TrafficSegForwardPorts The port list that the specific port can forward traffic to.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.69.3.2.13.1.1.2

The port security feature controls the address learning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as a
static entry. When the learned addresses number reaches N, any incoming packet that
has not learned a source address is discarded (e.g. dropped) and no more new addresses
can be learned on this port.

swL2PortSecurityControlEntry row .1.3.6.1.4.1.171.11.69.3.2.14.1.1

A list of information contained in the swL2PortSecurityControlTable.

Indexes

swL2PortSecurityPortIndex

Column	Syntax	OID
swL2PortSecurityPortIndex Indicates the secured port to lock address learning.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.171.11.69.3.2.14.1.1.1
swL2PortSecurityMaxLernAddr Indicates allowable number of addresses to be learned at this port.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.69.3.2.14.1.1.2
swL2PortSecurityMode Indicates the mode of locking address. In deleteOnTimeout (3) mode, the locked addresses can be aged out after the aging timer has expired. In this mode, when the locked address has aged …	Enumerationr/w Enumerated Values: 1 other 2 permanent 3 deleteOnTimeout 4 deleteOnReset	.1.3.6.1.4.1.171.11.69.3.2.14.1.1.3
swL2PortSecurityAdmState Indicates the administration state of the locking address.	Enumerationr/w Enumerated Values: 1 other 2 enable 3 disable	.1.3.6.1.4.1.171.11.69.3.2.14.1.1.4