DES3552-L2MGMT-MIB Table View

A table containing CFM state of speicified ports.

swL2DevCtrlCFMPortEntry row .1.3.6.1.4.1.171.11.105.3.2.1.2.21.2.1

The entry of CFM state on speicified ports.

Indexes

swL2DevCtrlCFMPortIndex

Column	Syntax	OID
swL2DevCtrlCFMPortIndex This object indicates the port-num.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.1.2.21.2.1.1
swL2DevCtrlCFMPortState This object indicates the CFM state on per-port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.1.2.21.2.1.2

A table containing static configuration information for
each VLAN configured into the device by (local or
network) management.  All entries are permanent and will
be restored after the device is reset.

swL2VlanStaticEntry row .1.3.6.1.4.1.171.11.105.3.2.2.1.1

Static information for a VLAN configured into the
device by (local or network) management.

Indexes

swL2VlanIndex

Column	Syntax	OID
swL2VlanIndex The VLAN-ID or other identifier referring to this VLAN.	VlanId Type Constraints: range: 1..4094	.1.3.6.1.4.1.171.11.105.3.2.2.1.1.1
swL2VLANAdvertisement This object indicates if the advertisement is active or not.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.2.1.1.2

A table containing vlan and port role information of each port.

swL2VlanPortInfoEntry row .1.3.6.1.4.1.171.11.105.3.2.2.3.1

The table entry of vlan port information.

Indexes

swL2VlanPortInfoPortIndex swL2VlanPortInfoVid

Column	Syntax	OID
swL2VlanPortInfoPortIndex The port index.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.2.3.1.1
swL2VlanPortInfoVid The VLAN-ID assigned to a special port	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.2.3.1.2
swL2VlanPortInfoPortRole The port role of a special port.when none,it means this port is not belong to the vlan.	Enumeration Enumerated Values: 1 none 2 untagged 3 tagged 4 dynamic 5 forbidden	.1.3.6.1.4.1.171.11.105.3.2.2.3.1.3

A table that contains information about every port.

swL2PortInfoEntry row .1.3.6.1.4.1.171.11.105.3.2.3.1.1

A list of information for each port of the device.

Indexes

swL2PortInfoPortIndex swL2PortInfoMediumType

Column	Syntax	OID
swL2PortInfoPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.1
swL2PortInfoMediumType Indicates medium type of the port number.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.2
swL2PortInfoUnitID Indicates ID of the unit in the system	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.3
swL2PortInfoType This object indicates the connector type of this port.	Enumeration Enumerated Values: 0 portType-none 2 portType-100Base-T 3 portType-100Base-X 4 portType-1000Base-T 5 portType-1000Base-X 6 portType-10GBase-R 7 portType-10GBase-CX4 8 portType-SIO 9 portType-module-empty 10 portType-user-last	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.4
swL2PortInfoLinkStatus This object indicates the port link status.	Enumeration Enumerated Values: 1 other 2 link-pass 3 link-fail	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.5
swL2PortInfoNwayStatus This object indicates the port speed and duplex mode.	Enumeration Enumerated Values: 0 link-down 1 full-10Mbps-8023x 2 full-10Mbps-none 3 half-10Mbps-backp 4 half-10Mbps-none 5 full-100Mbps-8023x 6 full-100Mbps-none 7 half-100Mbps-backp 8 half-100Mbps-none 9 full-1Gigabps-8023x 10 full-1Gigabps-none 11 half-1Gigabps-backp 12 half-1Gigabps-none 13 full-10Gigabps-8023x 14 full-10Gigabps-none 15 half-10Gigabps-8023x 16 half-10Gigabps-none 17 empty 18 err-disabled	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.6
swL2PortInfoErrorDisabled This object indicates the blocking type of this port.	Enumeration Enumerated Values: 0 none 1 storm 3 unknow 4 ctp-lbd 7 power-saving	.1.3.6.1.4.1.171.11.105.3.2.3.1.1.8

A table that contains control information about every port.

swL2PortCtrlEntry row .1.3.6.1.4.1.171.11.105.3.2.3.2.1

A list of control information for each port on the device.

Indexes

swL2PortCtrlPortIndex swL2PortCtrlMediumType

Column	Syntax	OID
swL2PortCtrlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.1
swL2PortCtrlMediumType Indicates the medium type of the port number.	Enumeration Enumerated Values: 1 copper 2 fiber	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.2
swL2PortCtrlUnitIndex Indicates the ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.3
swL2PortCtrlAdminState This object decides if the port is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.4
swL2PortCtrlNwayState Chose the port speed, duplex mode, and N-Way function mode.	Enumerationr/w Enumerated Values: 1 other 2 nway-enabled 3 nway-disabled-10Mbps-Half 4 nway-disabled-10Mbps-Full 5 nway-disabled-100Mbps-Half 6 nway-disabled-100Mbps-Full 7 nway-disabled-1Gigabps-Half 8 nway-disabled-1Gigabps-Full 9 nway-disabled-1Gigabps-Full-master 10 nway-disabled-1Gigabps-Full-slave	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.5
swL2PortCtrlFlowCtrlState The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, the IEEE 802.3x flow control function sends PAUSE fram…	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.6
swL2PortCtrlLearningState This object decides if the port is locked or not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.7
swL2PortCtrlMACNotifyState This object sets each port's MAC notification state.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.8
swL2PortCtrlMDIXState This object configures the MDIX setting of the port.	Enumerationr/w Enumerated Values: 1 auto 2 normal 3 cross	.1.3.6.1.4.1.171.11.105.3.2.3.2.1.10

A table that contains cable diagnostic information about every port.

swL2PortCableDiagnosisEntry row .1.3.6.1.4.1.171.11.105.3.2.3.5.1

A list of cable diagnostic information for each port of the device.

Indexes

swL2PortCableDiagnosisPortIndex swL2PortCableDiagnosisPairIndex

Column	Syntax	OID
swL2PortCableDiagnosisPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.1
swL2PortCableDiagnosisPairIndex Indicates pair index of the port. The pair 1 means the pin 3 and 6 of the connector. The pair 2 means the pin 1 and 2 of the connector. The pair 3 means the pin 7 and 8 of the connector. The pair 4 means the pin 4 and 5…	Integer32 Constraints: range: 1-4	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.2
swL2PortCableDiagnosisCableStatus This object indicates the cable status.	Enumeration Enumerated Values: 0 ok 1 open 2 short 3 open-short 4 not-support 5 unknown	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.3
swL2PortCableDiagnosisPairStatus This object indicates the status of the pair.	Enumeration Enumerated Values: 0 ok 1 open 2 short 3 fail 4 not-supported 5 unknown	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.4
swL2PortCableDiagnosisPairLength This object indicates the approx. length or length to failure of the pair. The unit value is in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.5
swL2PortCableDiagnosisPairLengthInaccuracy This object indicates the inaccuracy of a pair length. The unit value is in meters.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.3.5.1.6

A table that used to clear counter information about every port.

swL2PortCounterCtrlEntry row .1.3.6.1.4.1.171.11.105.3.2.3.6.1

A list of entry used to clear counter information for each port of the device.

Indexes

swL2PortCounterCtrlPortIndex

Column	Syntax	OID
swL2PortCounterCtrlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.6.1.1
swL2PortCounterClearCtrl This object indicates if to clear the counters for each port of the device or not.	Enumerationr/w Enumerated Values: 1 other 2 start	.1.3.6.1.4.1.171.11.105.3.2.3.6.1.2

A table that contains error information for each port.

swL2PortErrEntry row .1.3.6.1.4.1.171.11.105.3.2.3.7.1

A list of information regarding port errors on the device.

Indexes

swL2PortErrPortIndex

Column	Syntax	OID
swL2PortErrPortIndex This object indicates the module's port number.(1..Max port number in the module).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.3.7.1.1
swL2PortErrPortState This object indicates the port state is enabled or disabled.	Enumeration Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.3.7.1.2
swL2PortErrPortConnStatus This object indicates whether the PortStatus is err-disabled or not.	Enumeration Enumerated Values: 1 other 2 err-disabled	.1.3.6.1.4.1.171.11.105.3.2.3.7.1.3
swL2PortErrPortReason This object describes if the reason for the port error is STP LBD or Storm control.	Enumeration Enumerated Values: 2 storm-control 3 ctp-lbd 7 power-saving	.1.3.6.1.4.1.171.11.105.3.2.3.7.1.4

A table that contains information about multicast filter address.

swL2MulticastFilterProfileEntry row .1.3.6.1.4.1.171.11.105.3.2.5.1.1

A list of multicast filter address information for each profile ID.

Indexes

swL2MulticastFilterProfileIndex

Column	Syntax	OID
swL2MulticastFilterProfileIndex Indicates index for each profile.	Integer32 Constraints: range: 1-24	.1.3.6.1.4.1.171.11.105.3.2.5.1.1.1
swL2MulticastFilterProfileName Specifies a profile name for each multicast filter profile.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.171.11.105.3.2.5.1.1.2
swL2MulticastFilterStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.105.3.2.5.1.1.3

A table that contains information about multicast filter address.

swL2MulticastFilterProfileAddressEntry row .1.3.6.1.4.1.171.11.105.3.2.5.2.1

A list of multicast filter address information for each profile ID.

Indexes

swL2MulticastFilterProfileIdIndex swL2MulticastFilterFromIp swL2MulticastFilterToIp

Column	Syntax	OID
swL2MulticastFilterProfileIdIndex Indicates index for each profile.	Integer32 Constraints: range: 1-24	.1.3.6.1.4.1.171.11.105.3.2.5.2.1.1
swL2MulticastFilterFromIp Specifies the head IP address of a multicast address range which will be binded to a multicast filter profile.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.5.2.1.2
swL2MulticastFilterToIp Specifies the tail IP address of a multicast address range which will be binded to a multicast filter profile.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.5.2.1.3
swL2MulticastFilterAddressState This object indicates the status of this entry. Setting value to createAndGo(4) will add the multicast address list specified in swL2MulticastFilterFromIp and swL2MulticastFilterToIp to multicast filter profile. Settin…	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.105.3.2.5.2.1.4

A table that used to bind port to profile id.

swL2LimitedMulticastFilterPortEntry row .1.3.6.1.4.1.171.11.105.3.2.5.3.1

A list of information that used to bind port to profile id.

Indexes

swL2LimitedMulticastFilterPortIndex

Column	Syntax	OID
swL2LimitedMulticastFilterPortIndex Specifies port as an index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.5.3.1.1
swL2LimitedMulticastFilterPortAccess This object indicates the access status for each port.	Enumerationr/w Enumerated Values: 1 permit 2 deny	.1.3.6.1.4.1.171.11.105.3.2.5.3.1.2
swL2LimitedMulticastFilterPortProfileID This object specifies a profile ID list for each port.	SNMPv2-TCDisplayStringr/w Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.11.105.3.2.5.3.1.3
swL2LimitedMulticastFilterPortProfileStatus Controls the multicast filter profile list which bind to each port. When set add(2), multicast filter profile ID list which specifies in swL2LimitedMulticastFilterPortProfileID will be bound to the port. When set delete…	Enumerationr/w Enumerated Values: 1 other 2 add 3 delete	.1.3.6.1.4.1.171.11.105.3.2.5.3.1.4

A table that contains information about max group number based on port.

swL2MulticastFilterPortMaxGroupEntry row .1.3.6.1.4.1.171.11.105.3.2.5.4.1

A list of max group number information for each port.

Indexes

swL2MulticastFilterPortMaxGroupPortIndex

Column	Syntax	OID
swL2MulticastFilterPortMaxGroupPortIndex Specifies port number as table index.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.5.4.1.1
swL2MulticastFilterPortMaxGroup Specifies maximum multicast filter group numbers for each port. Default value is 0,and 0 means infinite.	Integer32r/w Constraints: range: 0-256	.1.3.6.1.4.1.171.11.105.3.2.5.4.1.2

.

swL2QOSBandwidthControlEntry row .1.3.6.1.4.1.171.11.105.3.2.6.1.1

A list of information contained in the swL2QOSBandwidthControlTable.

Indexes

swL2QOSBandwidthPortIndex

Column	Syntax	OID
swL2QOSBandwidthPortIndex Indicates the port .	Integer32 Constraints: range: 1-768	.1.3.6.1.4.1.171.11.105.3.2.6.1.1.1
swL2QOSBandwidthRxRate Indicates RX Rate of the specified port. Value 1024001 means no limit.	Integer32r/w Constraints: range: 64-1024001	.1.3.6.1.4.1.171.11.105.3.2.6.1.1.2
swL2QOSBandwidthTxRate Indicates TX Rate of the specified port. Value 1024001 means no limit.	Integer32r/w Constraints: range: 64-1024001	.1.3.6.1.4.1.171.11.105.3.2.6.1.1.3
swL2QOSBandwidthRadiusRxRate The RxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured RxRate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.6.1.1.4
swL2QOSBandwidthRadiusTxRate The TxRate value comes from RADIUS server, If an 802.1X port is authenticated, this value will overwrites the locally configured TxRate.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.6.1.1.5

.

swL2QOSSchedulingEntry row .1.3.6.1.4.1.171.11.105.3.2.6.2.1

A list of information contained in the swL2QOSSchedulingTable.

Indexes

swL2QOSSchedulingClassIndex

Column	Syntax	OID
swL2QOSSchedulingClassIndex Indicates the hardware queue number.	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.11.105.3.2.6.2.1.1
swL2QOSSchedulingMaxPkts Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 15 can be specified.	Integer32r/w Constraints: range: 0-15	.1.3.6.1.4.1.171.11.105.3.2.6.2.1.2
swL2QOSSchedulingMechanism Indicates the mechanism of QoS scheduling.	Enumeration Enumerated Values: 1 strict 2 roundrobin 3 weightfair	.1.3.6.1.4.1.171.11.105.3.2.6.2.1.3
swL2QOSSchedulingMaxLatency Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmitting its packets. A value between 0 and 255 can be spe…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.105.3.2.6.2.1.4

.

swL2QOS8021pUserPriorityEntry row .1.3.6.1.4.1.171.11.105.3.2.6.3.1

A list of information contained in the swL2QOS8021pUserPriorityTable.

Indexes

swL2QOS8021pUserPriorityIndex

Column	Syntax	OID
swL2QOS8021pUserPriorityIndex The 802.1p user priority .	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.11.105.3.2.6.3.1.1
swL2QOS8021pUserPriorityClass The number of the switch's hardware priority queue. The switch has seven hardware priority queues available. They are numbered between 0 (the lowest priority) and 6 (the highest priority).	Integer32r/w Constraints: range: 0-6	.1.3.6.1.4.1.171.11.105.3.2.6.3.1.2

.

swL2QOS8021pDefaultPriorityEntry row .1.3.6.1.4.1.171.11.105.3.2.6.4.1

A list of information contained in the swL2QOS8021pDefaultPriorityTable.

Indexes

swL2QOS8021pDefaultPriorityIndex

Column	Syntax	OID
swL2QOS8021pDefaultPriorityIndex Indicates the port number .	Integer32 Constraints: range: 1-768	.1.3.6.1.4.1.171.11.105.3.2.6.4.1.1
swL2QOS8021pDefaultPriority The priority value to assign to untagged packets received by the switch ports on the switch..	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.171.11.105.3.2.6.4.1.2
swL2QOS8021pRadiusPriority The value of 802.1p comes from RADIUS server. If an 802.1X port is authenticated, this value will overwrite the local configured value.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.6.4.1.3

A port security feature which controls the address leaning capability and      
traffic forwarding decisions. Each port can be enabled or disabled for this function.
When it is enabled and a number is given said N, which allows N addresses to be
learned on this port, the first N learned addresses are locked at this port as
static entries. When the learned addresses number reaches N, any incoming packet 
without learned source addresses are discarded (e.g. dropped) and no more new 
addresses can be learned on this port.

swL2PortSecurityControlEntry row .1.3.6.1.4.1.171.11.105.3.2.7.1.1

A list of information contained in the swL2PortSecurityControlTable.

Indexes

swL2PortSecurityPortIndex

Column	Syntax	OID
swL2PortSecurityPortIndex Indicates the secured port to lock address learning.	Integer32 Constraints: range: 1-768	.1.3.6.1.4.1.171.11.105.3.2.7.1.1.1
swL2PortSecurityMaxLernAddr Indicates allowable number of addresses to be learned on this port.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.7.1.1.2
swL2PortSecurityMode Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after the aging timer expires. In this mode, when the locked address is aged out, the number of addresses that ca…	Enumerationr/w Enumerated Values: 1 other 2 permanent 3 deleteOnTimeout 4 deleteOnReset	.1.3.6.1.4.1.171.11.105.3.2.7.1.1.3
swL2PortSecurityAdmState Indicates administration state of locking address.	Enumerationr/w Enumerated Values: 1 other 2 enable 3 disable	.1.3.6.1.4.1.171.11.105.3.2.7.1.1.4
swL2PortSecurityEntryClearCtrl Used to clear port security entries by port. Setting this value to 'start' will execute the clear action, Once cleared, the value returns to 'other'.	Enumerationr/w Enumerated Values: 1 other 2 start	.1.3.6.1.4.1.171.11.105.3.2.7.1.1.5

This table specifies the IP address as a destination to forward
(relay) DHCP packets to.

swL2DhcpRelayCtrlEntry row .1.3.6.1.4.1.171.11.105.3.2.8.7.1

A list of information that specifies the IP address as a destination
to forward (relay) DHCP packets to.

Indexes

swL2DhcpRelayCtrlInterfaceName swL2DhcpRelayCtrlServer

Column	Syntax	OID
swL2DhcpRelayCtrlInterfaceName The name of the IP interface.	OctetString Constraints: range: 1-12	.1.3.6.1.4.1.171.11.105.3.2.8.7.1.1
swL2DhcpRelayCtrlServer The DHCP server IP address.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.8.7.1.2
swL2DhcpRelayCtrlState This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. invalid(…	Enumerationr/w Enumerated Values: 1 other 2 invalid 3 valid	.1.3.6.1.4.1.171.11.105.3.2.8.7.1.3

This table specifies which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkCtrlEntry row .1.3.6.1.4.1.171.11.105.3.2.9.3.1

A list of information that specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkIndex

Column	Syntax	OID
swL2TrunkIndex The index number of the logical port trunk group. The trunk group number depends on the existence of unit and module.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.1
swL2TrunkMasterPort The object indicates the master port number of the port trunk entry. When using Port Trunk, you cannot configure the other ports of the group except the master port. Their configuration must be same as the master port …	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.3
swL2TrunkMember Indicates the number of ports included in this Trunk group. The trunk port number depends on the existence of the module. The maximum number of ports is 8 for one trunk group.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.4
swL2TrunkFloodingPort The object indicates the flooding port number of the port trunk entry. The first port of the Trunk group is implicitly configured to be the flooding port.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.5
swL2TrunkType This object indicates the type of trunk group. static : is static trunk group lacp : is LACP trunk group .	Enumerationr/w Enumerated Values: 1 other 2 static 3 lacp	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.6
swL2TrunkState This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.105.3.2.9.3.1.7

This table specifies which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkLACPPortEntry row .1.3.6.1.4.1.171.11.105.3.2.9.5.1

A list of information specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkLACPPortIndex

Column	Syntax	OID
swL2TrunkLACPPortIndex The index of logical port LACP.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.9.5.1.1
swL2TrunkLACPPortState The state of logical port LACP.	Enumerationr/w Enumerated Values: 1 active 2 passive	.1.3.6.1.4.1.171.11.105.3.2.9.5.1.2

This table is used to manage the VLAN trunking feature of the device.

swL2TrunkVLANEntry row .1.3.6.1.4.1.171.11.105.3.2.9.6.1

This object is used to configure the VLAN trunking settings for each port.

Indexes

swL2TrunkVLANPort

Column	Syntax	OID
swL2TrunkVLANPort This object indicates the port being configured.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.9.6.1.1
swL2TrunkVLANState The state of the logical port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.9.6.1.2

The table controls the VLAN's IGMP function. Its scale depends
on the current VLAN state (swL2VlanInfoStatus). If the VLAN is disabled, 
there is only one entry in the table, with an index of 1. If the            
VLAN is in Port-Base or 802.1q mode, the maximum number of entries can be 12, 
with an index range from 1 to 12.

swL2IGMPCtrlEntry row .1.3.6.1.4.1.171.11.105.3.2.11.4.1

The entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled.

Indexes

swL2IGMPCtrlVid

Column	Syntax	OID
swL2IGMPCtrlVid This object indicates the IGMP control entry's VLAN ID. If the VLAN is disabled, the VID is always 0 and cannot be changed by management users. If the VLAN is in Port-Base mode, the VID is arranged from 1 to 12, in a …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.1
swL2IGMPQueryInterval The frequency at which IGMP Host-Query packets are transmitted on this switch.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.2
swL2IGMPMaxResponseTime The maximum query response time on this switch.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.3
swL2IGMPRobustness The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.4
swL2IGMPLastMemberQueryInterval The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.5
swL2IGMPHostTimeout The timer value for sending IGMP query packets when none were sent by the host on the LAN. The timer works on a per-VLAN basis. Our device will be activated to send the query messages if the timer expires. Please ref…	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.6
swL2IGMPRouteTimeout The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.7
swL2IGMPLeaveTimer When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.8
swL2IGMPQueryState This object decides if the IGMP query is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.9
swL2IGMPCurrentState This object indicates the current IGMP query state.	Enumeration Enumerated Values: 1 other 2 querier 3 non-querier	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.10
swL2IGMPCtrlState This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(…	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.11
swL2IGMPFastLeaveState This object indicates the fast_leave status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following value…	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.171.11.105.3.2.11.4.1.12

The table contains the number current IGMP query packets which
are captured by this device, as well as the IGMP query packets
sent by the device.

swL2IGMPQueryInfoEntry row .1.3.6.1.4.1.171.11.105.3.2.11.5.1

Information about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of the associated VLAN
entry are all enabled.

Indexes

swL2IGMPInfoVid

Column	Syntax	OID
swL2IGMPInfoVid This object indicates the VID of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.5.1.1
swL2IGMPInfoQueryCount This object indicates the number of query packets received since the IGMP function was enabled, on a per-VLAN basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.5.1.2
swL2IGMPInfoTxQueryCount This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.5.1.3

The table containing current IGMP information which was captured by            
this device, provided that swL2DevCtrlIGMPSnooping and          
swL2IGMPCtrlState of the associated VLAN entries are all enabled. 
Note that the priority of IGMP table entries is lower than the Filtering            
Table, i.e. if there is a table hash collision between entries in the 
IGMP Table and Filtering Table inside the switch's H/W address table, 
then Filtering Table entry overwrites the colliding entry of the IGMP Table.  
Also see the swL2FilterMgmt description.

swL2IGMPInfoEntry row .1.3.6.1.4.1.171.11.105.3.2.11.6.1

Information about current IGMP information which was captured by
this device, provided that the swL2DevCtrlIGMPSnooping and the
swL2IGMPCtrlState of associated VLAN entries are all enabled.

Indexes

swL2IGMPVid swL2IGMPGroupIpAddr

Column	Syntax	OID
swL2IGMPVid This object indicates the VID of individual IGMP table entries. It shows the VID IGMP report information captured on the network.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.6.1.1
swL2IGMPGroupIpAddr This object identifies group IP addresses which were captured from IGMP packets, on a per-VLAN basis.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.11.6.1.2
swL2IGMPMacAddr This object identifies MAC addresses which correspond to the swL2IGMPGroupIpAddr, on per-VLAN basis.	MacAddress Type Constraints: range: 6	.1.3.6.1.4.1.171.11.105.3.2.11.6.1.3
swL2IGMPPortMap This object indicates which ports belong to the same multicast group, on a per-VLAN basis. Each multicast group has an octet string which is indicated by a port map. The most significant bit rep…	PortList Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.6.1.4
swL2IGMPIpGroupReportCount This object indicates how many report packets were receive by our device, that correspond with this entry when the IGMP function is enabled on per-VLAN basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.6.1.5

The information of the router port table.

swL2IGMPRouterPortEntry row .1.3.6.1.4.1.171.11.105.3.2.11.7.1

The entry of swL2IGMPRouterPortTable.

Indexes

swL2IGMPRouterPortVlanid

Column	Syntax	OID
swL2IGMPRouterPortVlanid This object indicates the VLAN ID of the router port entry.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.11.105.3.2.11.7.1.1
swL2IGMPRouterPortVlanName This object indicates the VLAN name of the router port entry.	OctetString Constraints: range: 0-32	.1.3.6.1.4.1.171.11.105.3.2.11.7.1.2
swL2IGMPRouterPortStaticPortList This object indicates the static portlist of the router port entry.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.7.1.3
swL2IGMPRouterPortDynamicPortList This object indicates the dynamic portlist of the router port entry.	PortList Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.7.1.4
swL2IGMPRouterPortForbiddenPortList This object indicates the forbidden portlist of the router port entry.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.7.1.5

The information of the IGMP snooping multicast VLAN table.

swL2IGMPMulticastVlanEntry row .1.3.6.1.4.1.171.11.105.3.2.11.8.1

The entry of swL2IGMPMulticastVlanTable.

Indexes

swL2IGMPMulticastVlanid

Column	Syntax	OID
swL2IGMPMulticastVlanid This object indicates the VLAN ID of the IGMP snooping multicast VLAN entry.	Integer32 Constraints: range: 2-4094	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.1
swL2IGMPMulticastVlanName This object indicates the VLAN name of the IGMP snooping multicast VLAN entry.	OctetStringr/w Constraints: range: 0-32	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.2
swL2IGMPMulticastVlanSourcePort This object indicate the portlist of the source ports of IGMP snooping multicast VLAN. The source ports will be set as tag ports of the VLAN entry. And the IGMP control messages received from the member ports would be…	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.3
swL2IGMPMulticastVlanMemberPort This object indicate the portlist of the member ports of the IGMP snooping multicast VLAN. The source ports will be set as untagged ports of the VLAN entry. And the IGMP control messages received from the member ports…	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.4
swL2IGMPMulticastVlanTagMemberPort This object indicate the portlist of the tag member ports of IGMP snooping multicast VLAN.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.5
swL2IGMPMulticastVlanState This object can be enabled or disabled IGMP_snooping multicast VLAN.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.6
swL2IGMPMulticastVlanReplaceSourceIp The replace source IP of this multicast vlan.	SNMPv2-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.7
swL2IGMPMulticastVlanRowStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.8
swL2IGMPMulticastVlanRemoveAllMcastAddrListAction This object indicates if remove all the multicast address list from the IGMP multicast VLAN or not.	Enumerationr/w Enumerated Values: 1 other 2 start	.1.3.6.1.4.1.171.11.105.3.2.11.8.1.9

The table containing the IGMP snooping multicast VLAN group information

swL2IGMPMulticastVlanGroupEntry row .1.3.6.1.4.1.171.11.105.3.2.11.9.1

Information about current IGMP snooping multicast VLAN group.

Indexes

swL2IGMPMulticastVlanGroupVid swL2IGMPMulticastVlanGroupFromIp swL2IGMPMulticastVlanGroupToIp

Column	Syntax	OID
swL2IGMPMulticastVlanGroupVid This object indicates the Vid of IGMP snooping multicast VLAN group.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.11.9.1.1
swL2IGMPMulticastVlanGroupFromIp Specifies the multicast address list for this VLAN.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.11.9.1.2
swL2IGMPMulticastVlanGroupToIp Specifies the multicast address list for this VLAN.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.105.3.2.11.9.1.3
swL2IGMPMulticastVlanGroupStatus This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.105.3.2.11.9.1.4

This table is used to manage the IGMP Access Authentication
configurations of the device.

swL2IGMPAccessAuthEntry row .1.3.6.1.4.1.171.11.105.3.2.11.13.1

A list of manageable entities for IGMP Access Authentication.
The configuration is done per port.

Indexes

swL2IGMPAccessAuthPort

Column	Syntax	OID
swL2IGMPAccessAuthPort The index of the swL2IGMPAccessAuthTable. This object corresponds to the port being configured.	SNMPv2-SMIInteger32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.171.11.105.3.2.11.13.1.1
swL2IGMPAccessAuthState This object denotes the status of IGMP Access Authentication of the port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.11.13.1.2

This table specifies that the port can just forward traffic to the 
specific port list.

swL2TrafficSegEntry row .1.3.6.1.4.1.171.11.105.3.2.14.1.1

A list of information which specifies the port with its traffic
forwarding list.

Indexes

swL2TrafficSegPort

Column	Syntax	OID
swL2TrafficSegPort The port number of the logical port.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.105.3.2.14.1.1.1
swL2TrafficSegForwardPorts The port list to which the specific port can forward traffic.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.105.3.2.14.1.1.2

A table that contains information about VLAN multicast filter mode.

swL2MulticastFilterModeVlanEntry row .1.3.6.1.4.1.171.11.105.3.2.17.1.1

A list of multicast filter mode information for each VLAN.

Indexes

swL2MulticastFilterVid

Column	Syntax	OID
swL2MulticastFilterVid Indicates VID for each VLAN.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.105.3.2.17.1.1.1
swL2MulticastFilterVlanMode Specifies multicast filter mode for each VLAN.	Enumerationr/w Enumerated Values: 1 forward-all-groups 2 forward-unregistered-groups 3 filter-unregistered-groups	.1.3.6.1.4.1.171.11.105.3.2.17.1.1.2

The table specifies the loopback detection function specified by port.

swL2LoopDetectPortEntry row .1.3.6.1.4.1.171.11.105.3.2.18.2.1.1

The table specifies the loopback detection function specified by port.

Indexes

swL2LoopDetectPortIndex

Column	Syntax	OID
swL2LoopDetectPortIndex This object indicates the module's port number. The range is from 1 to the maximum port number specified in the module	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.105.3.2.18.2.1.1.1
swL2LoopDetectPortState This object indicates the loopback detection function state on the port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.171.11.105.3.2.18.2.1.1.2
swL2LoopDetectPortLoopVLAN This object indicates the VLAN list that has detected a loopback.	SNMPv2-TCDisplayString Type Constraints: range: 0..255 Description: Represents textual information taken from the NVT ASCII character set, as defined in pages 4, 10-11 of RFC 854. To summarize RFC 854, the NVT ASCII repertoire specifies: - the use of c…	.1.3.6.1.4.1.171.11.105.3.2.18.2.1.1.3
swL2LoopDetectPortLoopStatus This object indicates the port status.	Enumeration Enumerated Values: 1 normal 2 loop 3 error 4 none	.1.3.6.1.4.1.171.11.105.3.2.18.2.1.1.4

This table is used to manage the DHCP local relay status 
for each VLAN.

swL2DhcpLocalRelayVLANEntry row .1.3.6.1.4.1.171.11.105.3.2.24.2.1

This object lists the current VLANs in the switch and their
corresponding DHCP local relay status.

Indexes

swL2DhcpLocalRelayVLANID

Column	Syntax	OID
swL2DhcpLocalRelayVLANID This object shows the VIDs of the current VLANS in the switch.	Integer32 Constraints: range: 1-4094	.1.3.6.1.4.1.171.11.105.3.2.24.2.1.1
swL2DhcpLocalRelayVLANState This object indicates the status of the DHCP relay function of the VLAN.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.105.3.2.24.2.1.2