DES3326SR-L2MGMT-MIB Table View

A list of temperature.

swDevInfoPowerEntry row .1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1

A entry of Power information.

Indexes

swDevInfoPowerUnitIndex swDevInfoPowerID

Column	Syntax	OID
swDevInfoPowerUnitIndex Indicates ID of the unit in the System	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.1
swDevInfoPowerID Indicates ID of the power	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.2
swDevInfoPowerStatus Indicates status of the power	Enumeration Enumerated Values: 0 other 1 lowVoltage 2 overCurrent 3 working 4 fail 5 connect 6 disconnect	.1.3.6.1.4.1.171.11.49.2.1.2.1.1.8.1.3

A table that contains information about every port.

swL2PortInfoEntry row .1.3.6.1.4.1.171.11.49.2.1.2.4.1.1

A list of information for each port of the device.

Indexes

swL2PortInfoPortIndex

Column	Syntax	OID
swL2PortInfoPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.1
swL2PortInfoUnitIndex Indicates ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.2
swL2PortInfoType This object indicates the connector type of this port.	Enumeration Enumerated Values: 1 portType-100Base-TX 2 portType-100Base-FX 3 portType-100Base-FL 4 portType-1000Base-TX 5 portType-1000Base-SX 6 portType-1000Base-LX 7 portType-1000Base-SX-GBIC 8 portType-1000Base-LX-GBIC 9 portType-1000Base-TX-GBIC 10 portType-1000Base-1394 11 none	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.3
swL2PortInfoLinkStatus This object indicates the port link status.	Enumeration Enumerated Values: 1 other 2 link-pass 3 link-fail	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.4
swL2PortInfoNwayStatus This object indicates the port speed and duplex mode.	Enumeration Enumerated Values: 1 other 2 auto 3 half-10Mbps 4 full-10Mbps 5 half-100Mbps 6 full-100Mbps 7 half-1Gigabps 8 full-1Gigabps	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.5
swL2PortInfoModuleType This object indicates the module type of this port.	Enumeration Enumerated Values: 0 none 1 moduleType-COMBO 2 moduleType-1394 3 moduleType-1000T 4 moduleType-MGBIC 5 moduleType-1P-SC-SX 6 moduleType-2P-SC-SX 7 moduleType-1P-SC-LX 8 moduleType-2P-SC-LX 9 moduleType-1P-TX 10 moduleType-2P-TX 11 moduleType-1P-MTRJ-SX 12 moduleType-2P-MTRJ-SX 13 moduleType-1P-MTRJ-LX 14 moduleType-2P-MTRJ-LX 15 moduleType-1P-GBIC 16 moduleType-2P-GBIC 17 moduleType-1P-GBIC-1P-TX 18 moduleType-1P-GBIC-1P-STACK 19 moduleType-2P-STACK 20 moduleType-2P-100FX 21 moduleType-1P-100FX 22 moduleType-2P-100FX-NEW 23 moduleType-1P-100FL 24 moduleType-2P-100FL 25 moduleType-2P-100TX 26 moduleType-BaseModule-24PORT	.1.3.6.1.4.1.171.11.49.2.1.2.4.1.1.6

A table that contains control information about every port.

swL2PortCtrlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.4.2.1

A list of control information for each port of the device.

Indexes

swL2PortCtrlPortIndex

Column	Syntax	OID
swL2PortCtrlPortIndex This object indicates the module's port number.(1..Max port number in the module)	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.1
swL2PortCtrlUnitIndex Indicates ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.2
swL2PortCtrlAdminState This object decide the port enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.3
swL2PortCtrlNwayState Chose the port speed, duplex mode, and N-Way function mode.	Enumerationr/w Enumerated Values: 1 other 2 nway-enabled 3 nway-disabled-10Mbps-Half 4 nway-disabled-10Mbps-Full 5 nway-disabled-100Mbps-Half 6 nway-disabled-100Mbps-Full 7 nway-disabled-1Gigabps-Half 8 nway-disabled-1Gigabps-Full	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.4
swL2PortCtrlFlowCtrlState The flow control mechanism is different between full duplex mode and half duplex mode. For half duplex mode, the jamming signal is asserted. For full duplex mode, IEEE 802.3x flow control function sends PAUSE frames a…	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.5
swL2PortCtrlLockState This object decide the port is locked or not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.6
swL2PortCtrlMACNotifyState This object decide the MAC notification is enable not.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.7
swL2PortCtrlMulticastfilter This object decide the multicast packets filtering mode on this port .	Enumerationr/w Enumerated Values: 0 other 1 forward-all-groups 2 forward-unregistered-groups 3 filter-unregistered-groups	.1.3.6.1.4.1.171.11.49.2.1.2.4.2.1.8

.

swL2QOSBandwidthControlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.6.1.1

A list of information contained in swL2QOSBandwidthControlTable.

Indexes

swL2QOSBandwidthPortIndex

Column	Syntax	OID
swL2QOSBandwidthPortIndex Indicates the port .	Integer32 Constraints: range: 1-650	.1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.1
swL2QOSBandwidthRxRate Indicates RX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.2
swL2QOSBandwidthTxRate Indicates TX Rate(Mbit/sec) of the specifed port. Value 0 means no limit.	Integer32r/w Constraints: range: 0-1000	.1.3.6.1.4.1.171.11.49.2.1.2.6.1.1.3

.

swL2QOSSchedulingEntry row .1.3.6.1.4.1.171.11.49.2.1.2.6.2.1

A list of information contained in swL2QOSSchedulingTable.

Indexes

swL2QOSSchedulingClassIndex

Column	Syntax	OID
swL2QOSSchedulingClassIndex Indicates the hardware queue number.	Integer32 Constraints: range: 0-3	.1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.1
swL2QOSSchedulingMaxPkts Indicates the maximum number of packets the hardware priority queue will be allowed to transmit before allowing the next lowest priority queue to transmit its packets. a value between 0 and 255 can be specified.	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.2
swL2QOSSchedulingMaxLatency Indicates the maximum amount of time the hardware priority queue will be allowed to transmit packets before allowing the next lowest priority queue to begin transmit its packets. A value between 0 and 255 can be specifi…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.49.2.1.2.6.2.1.3

.

swL2QOS8021pUserPriorityEntry row .1.3.6.1.4.1.171.11.49.2.1.2.6.3.1

A list of information contained in swL2QOS8021pUserPriorityTable.

Indexes

swL2QOS8021pUserPriorityIndex

Column	Syntax	OID
swL2QOS8021pUserPriorityIndex The 802.1p user priority .	Integer32 Constraints: range: 0-7	.1.3.6.1.4.1.171.11.49.2.1.2.6.3.1.1
swL2QOS8021pUserPriorityClass The number of the switch's hardware priority queue. The switch has four hardware priority queues available. They are numbered between 0 (the lowest priority) and 3 (the highest priority).	Integer32r/w Constraints: range: 0-3	.1.3.6.1.4.1.171.11.49.2.1.2.6.3.1.2

.

swL2QOS8021pDefaultPriorityEntry row .1.3.6.1.4.1.171.11.49.2.1.2.6.4.1

A list of information contained in swL2QOS8021pDefaultPriorityTable.

Indexes

swL2QOS8021pDefaultPriorityIndex

Column	Syntax	OID
swL2QOS8021pDefaultPriorityIndex Indicates the port number .	Integer32 Constraints: range: 1-650	.1.3.6.1.4.1.171.11.49.2.1.2.6.4.1.1
swL2QOS8021pDefaultPriority The priority value to assign to untagged packets received by the switch ports on the switch..	Integer32r/w Constraints: range: 0-7	.1.3.6.1.4.1.171.11.49.2.1.2.6.4.1.2

This table specifys which ports group a set of ports(up to 8)
into a single logical link.

swL2TrunkCtrlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.8.3.1

A list of information specifies which ports group a set of
ports(up to 8) into a single logical link.

Indexes

swL2TrunkIndex

Column	Syntax	OID
swL2TrunkIndex The index of logical port trunk. The trunk group number depend on the existence of unit and module.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.1
swL2TrunkName The name of logical port trunk.	RFC1213-MIBDisplayStringr/w Constraints: range: 0-12	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.2
swL2TrunkMasterPort The object indicates the master port number of the port trunk entry. When using Port Trunk, you can not configure the other ports of the group except the master port. Their configuration must be same as the master port…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.3
swL2TrunkMember Indicate how many number of ports is included in this Trunk. The trunk port number depend on the existence of module. The maximum number of ports is 8 for one trunks.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.4
swL2TrunkFloodingPort The object indicates the flooding port number of the port trunk entry. The first port of the trunk is implicitly configured to be the flooding port.	Integer32 Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.5
swL2TrunkType This object indicated that type of the trunk group. static : is static trunk group lacp : is LACP trunk group .	Enumerationr/w Enumerated Values: 1 other 2 static 3 lacp	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.6
swL2TrunkState This object indicates the status of this entry.	SNMPv2-TCRowStatusr/w Type Values: 1 active 2 notInService 3 notReady 4 createAndGo 5 createAndWait 6 destroy Description: The RowStatus textual convention is used to manage the creation and deletion of conceptual rows, and is used as the value of the SYNTAX clause for the status column of a conceptual row (as described in Section 7.7.1 of …	.1.3.6.1.4.1.171.11.49.2.1.2.8.3.1.7

The table controls the Vlan's IGMP function. Its scale depends
on current VLAN state (swL2VlanInfoStatus). If VLAN is disabled
mode, there is only one entry in the table, with index 1. If 
VLAN is in Port-Base or 802.1q mode, the number of entries can 
be up to 12, with index range from 1 to 12.

swL2IGMPCtrlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.10.3.1

The entry in IGMP control table (swL2IGMPCtrlTable). The entry
is effective only when IGMP capture switch
(swL2DevCtrlIGMPSnooping) is enabled.

Indexes

swL2IGMPCtrlVid

Column	Syntax	OID
swL2IGMPCtrlVid This object indicates the IGMP control entry's VLAN id. If VLAN is disabled, the Vid is always 0 and cannot be changed by management users. If VLAN is in Port-Base mode, the Vid is arranged from 1 to 12, fixed form. If …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.1
swL2IGMPQueryInterval The frequency at which IGMP Host-Query packets are transmitted on this switch.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.2
swL2IGMPMaxResponseTime The maximum query response time on this switch.	Integer32r/w Constraints: range: 1-25	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.3
swL2IGMPRobustness The Robustness Variable allows tuning for the expected packet loss on a subnet. If a subnet is expected to be lossy, the Robustness Variable may be increased. IGMP is robust to (Robustness Variable-1) packet losses.	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.4
swL2IGMPLastMemberQueryInterval The Last Member Query Interval is the Max Response Time inserted into Group-Specific Queries sent in response to Leave Group messages, and is also the amount of time between Group-Specific Query messages.	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.5
swL2IGMPHostTimeout The timer value for sending IGMP query packet when none was sent by the host in the LAN. The timer works in per-VLAN basis. Our device will be activated to send the query message if the timer is expired. Please refere…	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.6
swL2IGMPRouteTimeout The Router Timeout is how long a host must wait after hearing a Query before it may send any IGMPv2 messages.	Integer32r/w Constraints: range: 1-16711450	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.7
swL2IGMPLeaveTimer When a querier receives a Leave Group message for a group that has group members on the reception interface, it sends Group-Specific Queries every swL2IGMPLeaveTimer to the group being left.	Integer32r/w Constraints: range: 0-16711450	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.8
swL2IGMPQueryState This object decide the IGMP query enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.9
swL2IGMPCurrentState This object indicates the current IGMP query state.	Enumeration Enumerated Values: 1 other 2 querier 3 non-querier	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.10
swL2IGMPCtrlState This object indicates the status of this entry. other(1) - this entry is currently in use but the conditions under which it will remain so are different from each of the following values. disable(…	Enumerationr/w Enumerated Values: 1 other 2 disable 3 enable	.1.3.6.1.4.1.171.11.49.2.1.2.10.3.1.11

The table contains the number current IGMP query packets which
is captured by this device, as well as the IGMP query packets
sent by the device.

swL2IGMPQueryInfoEntry row .1.3.6.1.4.1.171.11.49.2.1.2.10.4.1

Information about current IGMP query information, provided that
swL2DevCtrlIGMPSnooping and swL2IGMPCtrState of associated VLAN
entry are all enabled.

Indexes

swL2IGMPInfoVid

Column	Syntax	OID
swL2IGMPInfoVid This object indicates the Vid of associated IGMP info table entry. It follows swL2IGMPCtrlVid in the associated entry of IGMP control table (swL2IGMPCtrlTable).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.1
swL2IGMPInfoQueryCount This object indicates the number of query packets received since the IGMP function enabled, in per-VLAN basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.2
swL2IGMPInfoTxQueryCount This object indicates the send count of IGMP query messages, in per-VLAN basis. In case of IGMP timer expiration, the switch sends IGMP query packets to related VLAN member ports and increment this object by 1.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.4.1.3

The table containing current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled. Note
that the priority of IGMP table entries is lower than Filtering
Table, i.e. if there is a table hash collision between the 
entries of IGMP Table and Filtering Table inside the switch H/W
address table, then Filtering Table entry overwrite the 
colliding entry of IGMP Table. See swL2FilterMgmt description 
also.

swL2IGMPInfoEntry row .1.3.6.1.4.1.171.11.49.2.1.2.10.5.1

Information about current IGMP information which captured by
this device, provided that swL2DevCtrlIGMPSnooping and
swL2IGMPCtrlState of associated VLAN entry are all enabled.

Indexes

swL2IGMPVid swL2IGMPGroupIpAddr

Column	Syntax	OID
swL2IGMPVid This object indicates the Vid of individual IGMP table entry. It shows the Vid of IGMP report information captured on network.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.1
swL2IGMPGroupIpAddr This object is identify group ip address which is captured from IGMP packet, in per-Vlan basis.	SNMPv2-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.2
swL2IGMPMacAddr This object is identify mac address which is corresponding to swL2IGMPGroupIpAddr, in per-Vlan basis.	SNMPv2-TCMacAddress Type Constraints: range: 6 Description: Represents an 802 MAC address represented in the `canonical' order defined by IEEE 802.1a, i.e., as if it were transmitted least significant bit first, even though 802.5 (in contrast to other 802.x protocols) requires M…	.1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.3
swL2IGMPPortMap This object indicates which ports are belong to the same multicast group, in per-Vlan basis. Each multicast group has a octect string to indicate with port map. The most significant bit represents the lowest numbered p…	PortList Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.4
swL2IGMPIpGroupReportCount This object indicate how much report packet was receive by our device corresponding with this entry from IGMP function enabled, in per-Vlan basis.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.10.5.1.5

This table specifys the storm traffic control configuration.

swL2TrafficCtrlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.12.1.1

A list of information specifies the storm traffic control
configuration.

Indexes

swL2TrafficCtrlGroupIndex

Column	Syntax	OID
swL2TrafficCtrlGroupIndex The index of logical port trunk. The trunk group number depend on the existence of unit and module.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.1
swL2TrafficCtrlUnitIndex Indicates ID of the unit in the device	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.2
swL2TrafficCtrlBMStromthreshold This object to decide how much thousand packets per second broadcast/multicast (depend on swL2TrafficCtrlBcastStromCtrl, swL2TrafficCtrlMcastStromCtrl or swL2TrafficCtrlDlfStromCtrl objects whether is enabled) will acti…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.3
swL2TrafficCtrlBcastStromCtrl This object indicates broadcast storm control function is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.4
swL2TrafficCtrlMcastStromCtrl This object indicates multicast storm control function is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.5
swL2TrafficCtrlDlfStromCtrl This object indicates destination lookup fail function is enabled or disabled.	Enumerationr/w Enumerated Values: 1 other 2 disabled 3 enabled	.1.3.6.1.4.1.171.11.49.2.1.2.12.1.1.6

This table specifys the port just can forward traffic to the 
specific port list.

swL2TrafficSegEntry row .1.3.6.1.4.1.171.11.49.2.1.2.13.1.1

A list of information specifies the port with its traffic
forward list.

Indexes

swL2TrafficSegPort

Column	Syntax	OID
swL2TrafficSegPort The port number of the logical port.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.13.1.1.1
swL2TrafficSegForwardPorts The port list that the specific port can forward traffic.	PortListr/w Type Constraints: range: 0..127	.1.3.6.1.4.1.171.11.49.2.1.2.13.1.1.2

port security feature which controls the address leaning capability and the
traffic forwarding decision. Each port can have this function enabled or disabled.
When it is enabled and a number is given said N, which allows N addresses to be
learned at this port, the first N learned addresses are locked at this port as
static entry. When the learned addresses number reach N, any coming packet with
not learned source addresses are discarded (e.g. dropped) and no more new addresses
can be learned at this port.

swL2PortSecurityControlEntry row .1.3.6.1.4.1.171.11.49.2.1.2.14.1.1

A list of information contained in swL2PortSecurityControlTable.

Indexes

swL2PortSecurityPortIndex

Column	Syntax	OID
swL2PortSecurityPortIndex Indicates the secured port to lock address learning.	Integer32 Constraints: range: 1-255	.1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.1
swL2PortSecurityMaxLernAddr Indicates allowable number of addresses to be learned at this port.	Integer32r/w Constraints: range: 0-65535	.1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.2
swL2PortSecurityMode Indicates the mode of locking address. In deleteOnTimeout(3) mode - the locked addresses can be aged out after aging timer expire. In this mode, when the locked address is aged …	Enumerationr/w Enumerated Values: 1 other 2 permanent 3 deleteOnTimeout 4 deleteOnReset	.1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.3
swL2PortSecurityAdmState Indicates administration state of locking address.	Enumerationr/w Enumerated Values: 1 other 2 enable 3 disable	.1.3.6.1.4.1.171.11.49.2.1.2.14.1.1.4