Cisco90Series-MIB Table View

This Cisco 90 Series Bank Di-group Table contains channel
bank level information for each of the channel bank di-groups
in the system. A di-group is a T1 interface to the frame
relay network. The table is indexed using the Cisco 90 Series
channel bank digroup number

frxBankEntry row .1.3.6.1.4.1.1570.1.3.1.1

A specific entry in the Cisco 90 Series Bank Di-group
Table. There is one entry for each channel bank di-group
(T1) in the system. There are no entries for unused banks

Indexes

frxBankIndex

Column	Syntax	OID
frxBankIndexmandatory Channel Bank Di-group Number. This index is used to address the various channel banks in the system. This number is the same as the DLCI number used to communicate with the bank at the Cisco 90 SNMP Agent. (note that th…	Integer32 Constraints: range: 16-1007	.1.3.6.1.4.1.1570.1.3.1.1.1
frxBankTypemandatory This is the type of channel bank and is for future use. D4 banks return a value of 1.	Enumerationr/w Enumerated Values: 1 d4	.1.3.6.1.4.1.1570.1.3.1.1.2

This Cisco 90 Series Channel Unit Table contains channel unit
level control and statistics for each of the Cisco 90 Series
channel units in the system. The table is indexed
first using the Cisco 90 Series channel bank digroup number,
then the channel unit number (1 to 24).

frxChUEntry row .1.3.6.1.4.1.1570.1.4.1.1

A specific entry in the Cisco 90 Series Channel Unit Table.
There is one entry for each Cisco 90 Series channel unit in
the system. There are no entries for unused banks or empty
channel unit slots

Indexes

frxBankIndex frxChUIndex

Column	Syntax	OID
frxChUIndexmandatory Channel Unit Number. This index is used to address a specific channel unit in a bank. For D4 channel banks this number is the same as the physical slot number 1-24	Integer32 Constraints: range: 1-24	.1.3.6.1.4.1.1570.1.4.1.1.1
frxChUTypemandatory Type of Cisco 90 Series channel unit installed.	Enumeration Enumerated Values: 100 cisco90i	.1.3.6.1.4.1.1570.1.4.1.1.2
frxChUVersionmandatory Cisco 90 Series channel unit version number.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.4.1.1.3
frxSigProtocolmandatory This is the type of Local In-channel Signaling used when the subscriber is running frame relay protocol. It is provided for future use. Set to 1 for T1.617 Annex-D	Enumeration Enumerated Values: 1 annexD	.1.3.6.1.4.1.1570.1.4.1.1.4
frxConfigSrcmandatory Source for configuring speed and protocol for each port. 1=Data rate and protocol set by DLCI assignment rules as reported by Annex-D. This option allows control of these basic parameters from the frame relay switc…	Enumerationr/w Enumerated Values: 1 annexD 2 snmp	.1.3.6.1.4.1.1570.1.4.1.1.5
frxDLCIAdLenmandatory The number of bytes used for the DLCI address. For future use. 1=two octets.	Enumeration Enumerated Values: 1 twoOctetDlci	.1.3.6.1.4.1.1570.1.4.1.1.6
frxNetInOctetsmandatory Total number of octets received by this channel unit from Frame Relay Switch (on the T1 interface) Only frames whose DLCI is addressed to a port on this channel unit are counted. Bad frames, Annex-D and SNMP frames are…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.7
frxNetOutOctetsmandatory Total number of octets transmitted to the Frame Relay Switch (on the T1 interface) by this channel unit. Annex-D and SNMP frames are not counted. CRC bytes are not counted	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.8
frxNetBadFramesmandatory Total number of frames received on the network (T1) interface that are discarded by this channel unit. Possible reasons for discard are: Frame contained HDLC abort (7 or more ones in a row) Frame had a CRC error …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.9
frxNetHDLCEsmandatory Network Errored Seconds caused by HDLC aborts (7 or more ones in a row). Total number of seconds in which a frame with an HDLC abort is received by this channel unit on the network (T1) interface. Only frames whose DLCI…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.10
frxNetCRCEsmandatory Network Errored Seconds caused by CRC errors. Total number of seconds in which a frame with a CRC error is received by this channel unit on the network (T1) interface. Only frames whose DLCI is addressed to a port on th…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.11
frxNetLinkEsmandatory Network Errored Seconds caused by Non-integral Bytes. Total number of seconds in which a frame with a non-integral number of bytes is received by this channel unit on the network (T1) interface. Only frames whose DLCI i…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.12
frxNetFrShEsmandatory Network Errored Seconds caused by Short Frames received. Total number of seconds in which a frame that is too short (less than 5 bytes) is received by this channel unit on the network (T1) interface. Only frames whose D…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.13
frxNetFrLgEsmandatory Network Errored Seconds caused by Long Frames received. Total number of seconds in which a frame that is too long (more than 8192 bytes) is received by this channel unit on the network (T1) interface. Only frames whose …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.14
frxNetPPPEsmandatory Errored seconds caused by bad RFC-1973 (PPP) header. Total number of seconds in which a frame with an invalid RFC-1973 (PPP) header is received by this channel unit on the network (T1) interface. Only frames whose DLCI …	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.15
frxNetBufEsmandatory Errored Seconds caused by Buffer Overflow. Total number of seconds in which a frame received by this channel unit on the network (T1) interface was discarded due to insufficient buffer space. Only frames whose DLCI is a…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.4.1.1.16

This table monitors and controls the T1-617 Annex-D
parameters used by the channel units. There is one
table row for every channel unit in every bank. The
table is indexed first using the Cisco 90 Series channel
bank digroup number, then the channel unit number (1 to 24).
For best performance, all of the channel units in a
given bank should be set to identical values.  These
values are typically set using global parameters in the
frxDefaultTable instead of directly via this table.

frxMgtEntry row .1.3.6.1.4.1.1570.1.5.1.1

A specific entry in the Cisco 90 Series Management Table.
There is one entry for each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots

Indexes

frxBankIndex frxChUIndex

Column	Syntax	OID
frxPortsInSvcmandatory Ports in service. The number of ports on a Cisco 90 Series channel unit that have one or more active PVCs, as determined by Annex-D.	Integer32 Constraints: range: 0-4	.1.3.6.1.4.1.1570.1.5.1.1.1
frxMgtT391mandatory This controls how often (in seconds) the channel unit sends an Annex-D poll to the frame relay switch. This is the Annex-D T391 parameter (Typical value 10)	Integer32r/w Constraints: range: 5-30	.1.3.6.1.4.1.1570.1.5.1.1.2
frxMgtT392mandatory This controls how long (in seconds) the channel unit will wait for a subscriber to send it an Annex-D poll before declaring a link error from the subscriber. This is the Annex-D T392 parameter (Typical value 15)	Integer32r/w Constraints: range: 5-30	.1.3.6.1.4.1.1570.1.5.1.1.3
frxMgtN391mandatory This controls how often (in polls) the channel unit sends a full status inquiry poll to the frame relay switch instead of a link integrity verification poll. This is the Annex-D N391 parameter (Typical value 6)	Integer32r/w Constraints: range: 1-255	.1.3.6.1.4.1.1570.1.5.1.1.4
frxMgtN392mandatory When more than frxMgtN392 errors are detected in any frxMgtN393 monitored Annex-D events, the network is declared inactive. This is the Annex-D N392 parameter (Typical value 3)	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.1570.1.5.1.1.5
frxMgtN393mandatory When more than frxMgtN392 errors are detected in any frxMgtN393 monitored Annex-D events, the network is declared inactive. This is the Annex-D N393 parameter (Typical value 4)	Integer32r/w Constraints: range: 1-10	.1.3.6.1.4.1.1570.1.5.1.1.6
frxNetLinkErrorsmandatory Number of signaling link reliability errors from network. A signaling reliability error is declared whenever the channel units did not receive a reply from the frame relay switch to an Annex-D link integrity poll or fu…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.1.1.7
frxNetProtErrorsmandatory Number of signaling protocol errors from network. A signaling protocol error is declared whenever the channel units receive a reply with incorrect format or sequence numbers from the frame relay switch in response to an…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.1.1.8
frxNetChInactivemandatory Number of times network Annex-D signaling channel was declared inactive.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.1.1.9
frxNetChStatusmandatory Current status of the Annex-D signaling channel on the network side of the channel bank.	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.1570.1.5.1.1.10

This table monitors the T1-617 Annex-D link
between the channel units and the subscribers.
There is one table row for every port on every
channel unit in every bank. The table is indexed
first using the channel bank digroup number, then
the channel unit number (1 to 24), and then the
port number (0 to 3).

frxMgtPortEntry row .1.3.6.1.4.1.1570.1.5.2.1

A specific entry in the Cisco 90 Series Management Port
Table. There is one entry for each port on each
Cisco 90 Series channel unit in the system. There are no
entries for unused banks or empty channel unit
slots.

Indexes

frxBankIndex frxChUIndex frxPortIndex

Column	Syntax	OID
frxPortIndexmandatory Which subscriber port on the channel unit is addressed. Ports are numbered from 0 to 3. Some channel unit types have less than 4 ports.	Integer32 Constraints: range: 0-3	.1.3.6.1.4.1.1570.1.5.2.1.1
frxPortLinkErrorsmandatory Number of signaling link reliability errors from subscriber port. A signaling reliability error is declared whenever the channel units did not receive an Annex-D link integrity poll or full status inquiry poll from the…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.2.1.2
frxPortProtErrorsmandatory Number of signaling protocol errors from subscriber port. A signaling protocol error is declared whenever the channel units receive an Annex-D link integrity poll or full status inquiry poll with incorrect format or seq…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.2.1.3
frxPortChInactivemandatory Number of times the subscriber port Annex-D signaling channel was declared inactive	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.5.2.1.4

This Cisco 90 Series Port Table contains per-port control and
statistics for each of the subscriber ports in the
system. The table is indexed first using the Cisco 90 Series
channel bank digroup number, then by the channel
unit number (1 to 24), and finally by the port
number (0-3).

frxPortEntry row .1.3.6.1.4.1.1570.1.6.1.1

A specific entry in the Cisco 90 Series Port Table. There is
one entry for each port on each Cisco 90 Series channel unit
in the system. There are no entries for unused banks or
empty channel unit slots.

Indexes

frxBankIndex frxChUIndex frxPortIndex

Column	Syntax	OID
frxPortSpeedmandatory This is the speed that the channel unit port runs at. 1=56kbps 2=64kbps 3=128kbps 4=144kbps This parameter can only be changed if frxConfigSrc is set to SNMP.	Enumerationr/w Enumerated Values: 1 use56kbps 2 use64kbps 3 use128kbps 4 use144kbps	.1.3.6.1.4.1.1570.1.6.1.1.1
frxPortProtocolmandatory This parameter controls what protocol the channel unit should expect the subscriber to send on the port. 1=Port uses Frame Relay protocol - no encapsulation 2=Port uses PPP protocol - do RFC-1973 encapsulation This …	Enumerationr/w Enumerated Values: 1 frameRelay 2 ppp	.1.3.6.1.4.1.1570.1.6.1.1.2
frxDSLStatusmandatory This is the status of the DSL loop to the subscriber. 1=Loop is down. 2=Frx card has achieved physical layer activation with the first BRITE card or the NT1 if there are no BRITE cards. 3=Link is up but Annex-D is sti…	Enumeration Enumerated Values: 1 loopDown 2 dslSyncOnly 3 loopUpInactive 4 loopUp	.1.3.6.1.4.1.1570.1.6.1.1.3
frxPVCAssignedmandatory Number of PVCs assigned to Subscriber Port as determined by Annex-D	Integer32 Constraints: range: 0-8	.1.3.6.1.4.1.1570.1.6.1.1.4
frxLastChangemandatory Time since DSL went in sync or lost sync in 0.01 second increments.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.5
frxBritemandatory Number of BRITE cards downstream. BRITE cards are used to extend the loop over subscriber loop carrier systems and are detected via a background polling operation.	Integer32 Constraints: range: 0-6	.1.3.6.1.4.1.1570.1.6.1.1.6
frxDSLInOctetsmandatory Number of octets received from the subscriber DSL Does not include Annex-D octets	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.7
frxDSLOutOctetsmandatory Number of octets transmitted to the subscriber DSL. Does not include Annex-D octets	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.8
frxT1InOctetsmandatory Number of octets received from the network directed at this subscriber port	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.9
frxT1OutOctetsmandatory Number of octets transmitted to the network from this subscriber port	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.10
frxDSLBadFramesmandatory Total number of frames received from this subscriber port that were discarded. Possible reasons for discard are: Frame contained HDLC abort (7 or more ones in a row) Frame had a CRC error Frame had a non-integr…	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.11
frxDSLHDLCEsmandatory Subscriber port Errored Seconds caused by HDLC aborts (7 or more ones in a row). Total number of seconds in which a frame with an HDLC abort is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.12
frxDSLCRCEsmandatory Subscriber port Errored Seconds caused by CRC errors. Total number of seconds in which a frame with a CRC error is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.13
frxDSLLinkEsmandatory Subscriber port Errored Seconds caused by Non-integral Bytes. Total number of seconds in which a frame with a non-integral number of bytes is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.14
frxDSLFrShEsmandatory Subscriber port Errored Seconds caused by Short Frames. received Total number of seconds in which a frame that is too short (less than 5 bytes) is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.15
frxDSLFrLgEsmandatory Subscriber port Errored Seconds caused by Long Frames received. Total number of seconds in which a frame that is too long (more than 8192 bytes) is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.16
frxDSLDLCIEsmandatory Subscriber port Errored Seconds caused by illegal DLCI. Total number of seconds in which a frame that has a DLCI other than 16 to 23 (or 0) is received from this port.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.17
frxTxBufmandatory Number of octets in the transmit buffer for this subscriber port. This data is waiting to be sent to the network (T1).	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.1.1.18
frxRxBufmandatory Number of octets in the receive buffer for this subscriber port. This data is from the network (T1) and is waiting to be sent to the subscriber port.	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.1.1.19
frxPortNetEsmandatory Total number of seconds in which a frame received from the network (T1) and targeted at this subscriber port was discarded.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.1.1.20

This Cisco 90 Series Circuit Table contains
per-virtual-circuit control and statistics for each of the
permanent virtual circuits in the system. The table is
indexed first using the Cisco 90 Series channel bank
digroup number, then by the channel unit number (1 to 24),
then by the port number (0-3) and finally by the circuit
DLCI number (16 to 23).

frxCircuitEntry row .1.3.6.1.4.1.1570.1.6.2.1

A specific entry in the Cisco 90 Series Circuit Table.
There is one entry for each permanent virtual circuit
in the system. There are no entries for unused
banks or empty channel unit slots.

Indexes

frxBankIndex frxChUIndex frxPortIndex frxPvcIndex

Column	Syntax	OID
frxPvcIndexmandatory This index is the subscriber loop DLCI number of the permanent virtual circuit. It ranges from 16 to 23. The corresponding network side DLCI must be assigned in the frame relay switch and communicated to the Cisco 90 Se…	Integer32 Constraints: range: 16-23	.1.3.6.1.4.1.1570.1.6.2.1.1
frxCktCIRmandatory This is the committed information rate (CIR) in bits per second for the addressed permanent virtual circuit. (Typical value 1536000/#ports).	Integer32r/w Constraints: range: 0-1544000	.1.3.6.1.4.1.1570.1.6.2.1.2
frxCktBcmandatory This is the Committed Burst Size (Bc) in bits for the addressed permanent virtual circuit. The time interval over which the burst is measured is Bc/CIR. (Typically set to same number as frxCktCIR).	Integer32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.1570.1.6.2.1.3
frxCktBemandatory This is the Excess Burst Size (Be) in bits for the addressed permanent virtual circuit. The time interval over which the excess burst is measured is Be/CIR. (Typical value 1536000).	Integer32r/w Constraints: range: 0-16777215	.1.3.6.1.4.1.1570.1.6.2.1.4
frxFarEndOpStatmandatory This is the status of the far end of the frame relay permanent virtual circuit (through the frame relay network) as determined by Annex-D. 1=active 2=inactive	Enumeration Enumerated Values: 1 active 2 inactive	.1.3.6.1.4.1.1570.1.6.2.1.5
frxCktInOctetsmandatory The number of input octets from the subscriber port on the addressed permanent virtual circuit. These octets are destined for the network (T1).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.2.1.6
frxCktOutOctetsmandatory The number of output octets to the subscriber port on the addressed permanent virtual circuit. These octets were received from the network (T1).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.2.1.7
frxCktInFramesmandatory The number of input frames from the subscriber port on the addressed permanent virtual circuit. These frames are destined for the network (T1).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.2.1.8
frxCktOutFramesmandatory The number of output frames to the subscriber port on the addressed permanent virtual circuit. These frames were received from the network (T1).	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.2.1.9
frxCktDiscardsmandatory The number of input frames from the subscriber port on the addressed permanent virtual circuit that were discarded due to congestion (lack of buffer space or congestion control.	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.2.1.10

This Cisco 90 Series Embedded Operations Channel Table
is used to diagnose and sectionalize problems with the
subscriber loop.  It contains one entry for each of the
Cisco 90 Series channel units in the system. The table
is indexed first using the Cisco 90 Series channel bank
digroup number, then the channel unit number (1 to 24).

frxUEocEntry row .1.3.6.1.4.1.1570.1.6.3.1

A specific entry in the Cisco 90 Series Embedded Operations
Channel Table. There is one entry for each Cisco 90 Series
channel unit in the system. There are no entries for unused
banks or empty channel unit slots

Indexes

frxBankIndex frxChUIndex

Column	Syntax	OID
frxTestPortmandatory This parameter indicates which subscriber port on the channel unit to test. It has no effect until frxStartTest is set to start the test. Only one port on a given channel unit may be tested at a time.	Integer32r/w Constraints: range: 0-3	.1.3.6.1.4.1.1570.1.6.3.1.1
frxTestTypemandatory This parameter indicates the type of test to perform. It has no effect until frxStartTest is set to start the test. 1=Set up a loopback and run a PN-2047 Bit Error Rate Test. 2=Run a (straightaway) PN-2047 Bit Error Rat…	Enumerationr/w Enumerated Values: 1 loopbackAndBert 2 bertOnly 3 sendCorruptCRC 4 loopbackOnly 5 localLoopAllPorts	.1.3.6.1.4.1.1570.1.6.3.1.2
frxLoopLocmandatory This parameter indicates the location of the loopback or the card that will send corrupt CRC. It has no effect until frxStartTest is set to start the test. It has no effect for a BertOnly test. 7=Local Cisco 90 Series …	Enumerationr/w Enumerated Values: 1 briteCard1 2 briteCard2 3 briteCard3 4 briteCard4 5 briteCard5 6 briteCard6 7 localFrx 8 nt1	.1.3.6.1.4.1.1570.1.6.3.1.3
frxLoopChmandatory This parameter indicates which channels to use for the loopbackOnly and localLoopAllPorts test. It has no effect until frxStartTest is set to start the test. Note that the loopbackAndBert test always loops all channels …	Enumerationr/w Enumerated Values: 1 b1only 2 b2only 3 all	.1.3.6.1.4.1.1570.1.6.3.1.4
frxStartTestmandatory This parameter is used to start and stop the test. frxTestPort, frxTestType, frxLoopLoc, and frxLoopCh should be set up prior to starting the test. 1=stop test. 2=start test.	Enumerationr/w Enumerated Values: 1 stopTest 2 startTest	.1.3.6.1.4.1.1570.1.6.3.1.5
frxBertRstmandatory This parameter may be used during a LoopbackAndBert test or a BertOnly test to reset the frxBertBE counter. It must be returned to the normal posiion to allow errors to be counted. 1=normal. 2=Reset BERT counter.	Enumerationr/w Enumerated Values: 1 normal 2 resetBert	.1.3.6.1.4.1.1570.1.6.3.1.6
frxBertBEmandatory BERT test block errors	RFC1155-SMICounter Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.3.1.7
frxBertTestTimemandatory BERT test time in 0.01 second increments	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.1570.1.6.3.1.8
frxTestInProgmandatory Test in progress (1); Normal operation (2)	Enumeration Enumerated Values: 1 testInProgress 2 normalOperation	.1.3.6.1.4.1.1570.1.6.3.1.9

This table contains the U-interface Performance Monitoring
Thresholds and Alarms for each of the subscriber loops in
the system and for any BRITE cards extending those loops
(e.g. using Subscriber Loop Carrier systems)  The table is
indexed first using the Cisco 90 Series channel bank digroup
number, then the channel unit number (1 to 24), then the port
number (0, 1, etc) and finally the location number (the BRITE
card number (1 to 6) or 7 for local parameters in the Cisco
90 Series card). These registers are defined by Bellcore
TR-TSY-000829.

frxUThrEntry row .1.3.6.1.4.1.1570.1.6.4.1

A specific entry in the U-interface Performance Monitoring
Threshold table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …

Indexes

frxBankIndex frxChUIndex frxPortIndex frxPAddrIndex

Column	Syntax	OID
frxPAddrIndexmandatory This is the physical location where the performance monitoring takes place. It may be set to localFrx(7) to access and control PM values local to the Cisco 90 Series channel unit. If there are BRITE cards in the subscr…	Enumeration Enumerated Values: 1 briteCard1 2 briteCard2 3 briteCard3 4 briteCard4 5 briteCard5 6 briteCard6 7 localFrx	.1.3.6.1.4.1.1570.1.6.4.1.1
frxChEsThmandatory Current Hour Errored Seconds threshold. This threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask register is …	Integer32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.1570.1.6.4.1.2
frxCdEsThmandatory Current Day Errored Seconds threshold. This threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask register is 0…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.1570.1.6.4.1.3
frxChSesThmandatory Current Hour Severely Errored Seconds threshold. This threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask reg…	Integer32r/w Constraints: range: 1-3600	.1.3.6.1.4.1.1570.1.6.4.1.4
frxCdSesThmandatory Current Day Severely Errored Seconds threshold. This threshold is used for both the transmit and receive directions. When errors are detected that exceed this threshold and the corresponding bit in the frxAlertMask regi…	Integer32r/w Constraints: range: 1-65535	.1.3.6.1.4.1.1570.1.6.4.1.5
frxAlertMaskmandatory 8-bit Alert Mask register. One bit for each threshold in both directions. When set to 1, the corresponding threshold crossing is ignored. When set to 0, the corresponding threshold crossing is indicated in frxThCond an…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.1570.1.6.4.1.6
frxThCondmandatory 8-bit Threshold Condition register. One bit for each threshold in both directions. Set to 1 if the threshold is exceeded and the corresponding bit in the frxAlertMask register is set to 0. Only set to 0 by the SNMP man…	Integer32r/w Constraints: range: 0-255	.1.3.6.1.4.1.1570.1.6.4.1.7

This table contains the U-interface Performance Monitoring
Statistics for each of the subscriber loops in the system
and for any BRITE cards extending those loops (e.g. using
Subscriber Loop Carrier systems)  The table is indexed
first using the Cisco 90 Series channel bank digroup number,
then the channel unit number (1 to 24), then the port number
(0, 1, etc) and finally the location number (the BRITE card
number (1 to 6) or 7 for local parameters in the Cisco 90
Series card). These registers are defined by Bellcore
TR-TSY-000829.

frxUPerfEntry row .1.3.6.1.4.1.1570.1.6.5.1

A specific entry in the U-interface Performance Monitoring
Statistics table. There is one entry for each port on each
Cisco 90 Series channel unit in the system and one entry for
each BRITE card extending those ports. …

Indexes

frxBankIndex frxChUIndex frxPortIndex frxPAddrIndex

Column	Syntax	OID
frxResetPMmandatory Reset all of the performance monitoring statistics on the specified Cisco 90 Series channel unit or BRITE card. 1=Normal. 2=Reset. There is no need to set this register back to Normal after doing a reset.	Enumerationr/w Enumerated Values: 1 normal 2 resetPM	.1.3.6.1.4.1.1570.1.6.5.1.1
frxPMtypemandatory Determines if the Cisco 90 Series channel unit or the downstream BRITE cards is doing segmented or path performance monitoring as specified in Bellcore document TR-NWT-000397. Only segmented performance monitoring shou…	Enumeration Enumerated Values: 1 segmentedPM 2 pathPM	.1.3.6.1.4.1.1570.1.6.5.1.2
frxChEsTxmandatory Current Hour Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical …	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.3
frxChEsRxmandatory Current Hour Errored Seconds - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical li…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.4
frxPhEsTxmandatory Previous Hour Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.5
frxPhEsRxmandatory Previous Hour Errored Seconds - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.6
frxH2EsTxmandatory Errored Seconds 2 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.7
frxH2EsRxmandatory Errored Seconds 2 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.8
frxH3EsTxmandatory Errored Seconds 3 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.9
frxH3EsRxmandatory Errored Seconds 3 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.10
frxH4EsTxmandatory Errored Seconds 4 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.11
frxH4EsRxmandatory Errored Seconds 4 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.12
frxH5EsTxmandatory Errored Seconds 5 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.13
frxH5EsRxmandatory Errored Seconds 5 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.14
frxH6EsTxmandatory Errored Seconds 6 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.15
frxH6EsRxmandatory Errored Seconds 6 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.16
frxH7EsTxmandatory Errored Seconds 7 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.17
frxH7EsRxmandatory Errored Seconds 7 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.18
frxH8EsTxmandatory Errored Seconds 8 hours ago - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.19
frxH8EsRxmandatory Errored Seconds 8 hours ago - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.20
frxCdEsTxmandatory Current Day Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical l…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.21
frxCdEsRxmandatory Current Day Errored Seconds - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical lin…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.22
frxPdEsTxmandatory Previous Day Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical …	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.23
frxPdEsRxmandatory Previous Day Errored Seconds - Receive direction. Receive is data from the customer towards the network. Errored Seconds are seconds in which one or more block errors occur. These errors are measured at the physical li…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.24
frxChSesTxmandatory Current Hour Severely Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measu…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.25
frxChSesRxmandatory Current Hour Severely Errored Seconds - Receive direction. Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measure…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.26
frxPhSesTxmandatory Previous Hour Severely Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are meas…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.27
frxPhSesRxmandatory Previous Hour Severely Errored Seconds - Receive direction. Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measur…	Integer32 Constraints: range: 0-3600	.1.3.6.1.4.1.1570.1.6.5.1.28
frxCdSesTxmandatory Current Day Severely Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measur…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.29
frxCdSesRxmandatory Current Day Severely Errored Seconds - Receive direction. Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measured…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.30
frxPdSesTxmandatory Previous Day Severely Errored Seconds - Transmit direction. Transmit is data from the network towards the customer. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measu…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.31
frxPdSesRxmandatory Previous Day Severely Errored Seconds - Receive direction. Receive is data from the customer towards the network. Severely Errored Seconds are seconds in which three or more block errors occur. These errors are measure…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.32
frxChBeTxmandatory Current Hour Block Errors - Transmit direction. Transmit is data from the network towards the customer. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. The…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.33
frxChBeRxmandatory Current Hour Block Errors - Receive direction. Receive is data from the customer towards the network. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. These…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.34
frxPhBeTxmandatory Previous Hour Block Errors - Transmit direction. Transmit is data from the network towards the customer. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. Th…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.35
frxPhBeRxmandatory Previous Hour Block Errors - Receive direction. Receive is data from the customer towards the network. Block errors are 12 millisecond time periods in which a physical link level (e.g. DSL CRC or BPV) error occurs. Thes…	Integer32 Constraints: range: 0-65535	.1.3.6.1.4.1.1570.1.6.5.1.36