CT-ELS10-27-MIB Table View

This table contains configuration information specify-
ing the types of protocols used to bridge, route,
translate, and filter frames for each port.

els10-27protoEntry row .1.3.6.1.4.1.97.9.12.1.1

Each entry in this table specifies which protocols are
used by a particular port in the ES/1.

Indexes

els10-27protoIfIndex

Column	Syntax	OID
els10-27protoIfIndexmandatory Identifies the interface (port) to which this entry's information belongs. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.12.1.1.1
els10-27protoBridgemandatory Defines the bridging method to be applied to frames received at, or destined for, this port. Ethernet and FDDI ports may be configured for transparent, srt, or none. Token Ring ports may be configured for any of the fo…	Enumerationr/w Enumerated Values: 1 transparent 4 none	.1.3.6.1.4.1.97.9.12.1.1.2
els10-27protoSuppressBpdumandatory Allows transmission of spanning tree protocol packets to be suppressed. If normal(1), 802.1d spanning tree packets are transmitted as usual. If suppressed(2), these packets are not transmitted. This option may be neede…	Enumerationr/w Enumerated Values: 1 normal 2 suppressed	.1.3.6.1.4.1.97.9.12.1.1.3
els10-27protoRipListenmandatory Specifies whether the port should listen for internet Routing Information Protocol (RFC-1058) packets, in order to build the routing table for the unit.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.97.9.12.1.1.4
els10-27protoTrunkingmandatory Specifies whether SMC's trunking protocol (an extension to the standard Spanning Tree) is to be used over this port.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.97.9.12.1.1.5
els10-27sprotoTransmitPacingmandatory When enabled, introduces delays into normal transmission of frames, to reduce the probability of collisions during heavy traffic.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.97.9.12.1.1.6

This table describes the trunking status and attributes of
the interfaces that are configured for bridge trunking.

els10-27trunkEntry row .1.3.6.1.4.1.97.9.13.1.1

An entry exists in this table for each physical interface
(port) that is configured for trunking.

Indexes

els10-27trunkIfIndex

Column	Syntax	OID
els10-27trunkIfIndexmandatory Identifies a physical interface (port) which is configured for LAN trunking. The value of this variable corresponds to ifIndex, as well as most of the other port identification values in related MIBs.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.13.1.1.1
els10-27trunkStatemandatory If off(1) then this link has not been enabled for trunking. If closed(2) then this link has not yet received any Trunking PDUs. If oneway(3) then incoming Trunking PDUs do not indicate that our PDUs are being successful…	Enumeration Enumerated Values: 1 off 2 closed 3 oneway 4 joined 5 perturbed 6 helddown 7 broken	.1.3.6.1.4.1.97.9.13.1.1.2
els10-27trunkRemoteBridgeAddrmandatory The MAC address portion of the bridge ID of the remote bridge.	OctetString	.1.3.6.1.4.1.97.9.13.1.1.3
els10-27trunkRemoteIpmandatory The IP address of the remote bridge, as reported by that bridge for administrative purposes.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.97.9.13.1.1.4
els10-27trunkLastErrormandatory The last reason for failure when the link is in closed, oneway, or helddown state.	Enumeration Enumerated Values: 1 none 2 in-bpdu 3 multiple-bridges 4 ack-lost 5 standby 6 too-many-groups 7 no-ack 8 perturbed-threshold 9 self-connect 10 port-moved 11 multiple-lan-types	.1.3.6.1.4.1.97.9.13.1.1.5
els10-27trunkLinkOrdinalmandatory The position of this link within the trunk group.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.13.1.1.6
els10-27trunkLinkCountmandatory The number of links within the trunk group.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.13.1.1.7
els10-27trunkLastChangemandatory The number of seconds since els10-27trunkState changed.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.13.1.1.8

This table contains work group definitions for the interfaces.

els10-27WorkGroupEntry row .1.3.6.1.4.1.97.9.14.4.1

Each entry in this table contains a definition of a work group.

Indexes

els10-27WorkGroupNumber

Column	Syntax	OID
els10-27WorkGroupNumbermandatory An integer that identifies the work group, used as an index to this table.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.14.4.1.1
els10-27WorkGroupNamemandatory A 1-16 character work group name.	RFC1213-MIBDisplayStringr/w	.1.3.6.1.4.1.97.9.14.4.1.2
els10-27WorkGroupPortsmandatory A list of all ports within the group. The first octet specified ports 1-8, the second 9-16, etc.	OctetStringr/w	.1.3.6.1.4.1.97.9.14.4.1.3
els10-27WorkGroupTypemandatory The type of work group: all - no additional information needs to be supplied.	Enumerationr/w Enumerated Values: 3 all 4 invalid	.1.3.6.1.4.1.97.9.14.4.1.4

This table contains information about the severity of each trap
and whether the trap is currently enabled.

els10-27trapControlEntry row .1.3.6.1.4.1.97.9.15.1.1

Indexes

els10-27trapIndex

Column	Syntax	OID
els10-27trapIndexmandatory The specific trap number.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.15.1.1.1
els10-27trapEnabledmandatory Enable or disable the generation of this trap.	Enumerationr/w Enumerated Values: 1 true 2 false	.1.3.6.1.4.1.97.9.15.1.1.2
els10-27trapSeveritymandatory A user-definable severity, indicating the importance of the trap.	Enumerationr/w Enumerated Values: 1 informational 2 warning 3 minor 4 major 5 critical	.1.3.6.1.4.1.97.9.15.1.1.3
els10-27trapTextmandatory A description of the trap.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.97.9.15.1.1.4

This table contains information about whether a class of
traps of a particular severity are enabled or disabled.

els10-27trapSeverityControlEntry row .1.3.6.1.4.1.97.9.15.2.1

Indexes

els10-27trapSeverity

Column	Syntax	OID
els10-27trapSeverityControlSeveritymandatory A user-definable severity, indicating the importance of the trap.	Enumerationr/w Enumerated Values: 1 informational 2 warning 3 minor 4 major 5 critical	.1.3.6.1.4.1.97.9.15.2.1.1
els10-27trapSeverityEnablemandatory Enable or disable all traps of a given severity level.	Enumerationr/w Enumerated Values: 1 enabled 2 disabled	.1.3.6.1.4.1.97.9.15.2.1.2

This table contains the latest traps that have been generated.

els10-27trapEntry row .1.3.6.1.4.1.97.9.15.7.1

Indexes

els10-27trapEntryIndex

Column	Syntax	OID
els10-27trapEntryIndexmandatory A number representing the order in which the trap occurred in time. This 32 bit number can wrap.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.15.7.1.1
els10-27trapEntryTimeStampmandatory The time at which the trap occurred.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.15.7.1.2
els10-27trapEntryTextmandatory A description of the trap.	RFC1213-MIBDisplayString	.1.3.6.1.4.1.97.9.15.7.1.3
els10-27trapEntryNumbermandatory The specific trap number, as specified in the TRAP PDU.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.15.7.1.4
els10-27trapEntrySeveritymandatory A user-definable severity, indicating the importance of the trap.	Enumeration Enumerated Values: 1 informational 2 warning 3 minor 4 major 5 critical	.1.3.6.1.4.1.97.9.15.7.1.5

The set of information describing the active ping requests and
their results.

els10-27pingEntry row .1.3.6.1.4.1.97.9.16.2.1

The parameters, state, and results of a ping request.

Indexes

els10-27pingNMSAddr els10-27pingDestAddr

Column	Syntax	OID
els10-27pingNMSAddrmandatory The IP address of the NMS, used to determine which ping request to return information on.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.97.9.16.2.1.1
els10-27pingDestAddrmandatory The IP address which is to be the destination of the ping ECHO_REQUEST. This variable cannot be set while els10-27pingOperation is on.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.97.9.16.2.1.2
els10-27pingStatemandatory The current state of the ping request.	Enumeration Enumerated Values: 0 not-started 1 active 2 timed-out 3 completed	.1.3.6.1.4.1.97.9.16.2.1.3
els10-27pingCountmandatory The number of ping requests which are to be sent. This variable cannot be set while els10-27pingOperation is on.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.16.2.1.4
els10-27pingDataSizemandatory The datagram packet size which will be sent with the ECHO_REQUEST, in bytes. This variable cannot be set while els10-27pingOperation is on.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.16.2.1.5
els10-27pingWaitmandatory The time, in centiseconds, between the sending of each ECHO_REQUEST message. This variable cannot be set while els10-27pingOperation is on.	RFC1155-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.16.2.1.6
els10-27pingTimeOutmandatory The time, in centiseconds, since the last ECHO_RESPONSE was received (or the last ECHO_REQUEST was sent, if there have been no responses) when the ping request will time out. This variable cannot be set while els10-27pi…	RFC1155-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.16.2.1.7
els10-27pingOperationmandatory Setting els10-27pingOperation to on will begin the ping request. Setting els10-27pingOperation to off will terminate the ping request.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.97.9.16.2.1.8
els10-27pingMinmandatory The minimum round trip time for the ping requests and responses, in centiseconds.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.16.2.1.9
els10-27pingMaxmandatory The maximum round trip for the ping requests and responses, in centiseconds.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.16.2.1.10
els10-27pingAvgmandatory The average round trip time for the ping requests and responses, in centiseconds.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.16.2.1.11
els10-27pingNumTransmittedmandatory The number of ICMP ECHO_REQUEST messages that have been transmitted during this ping request.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.16.2.1.12
els10-27pingNumReceivedmandatory The number of ICMP ECHO_RESPONSE messages that have been received as a result of this ping request.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.16.2.1.13

The set of information describing the active traceroute requests
and their results.

els10-27traceEntry row .1.3.6.1.4.1.97.9.17.2.1

The parameters, state, and results of a traceroute request.

Indexes

els10-27traceNMSAddr els10-27traceDestAddr els10-27traceHop els10-27traceProbe

Column	Syntax	OID
els10-27traceNMSAddrmandatory The IP address of the NMS, used to determine which traceroute request to return information on.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.97.9.17.2.1.1
els10-27traceDestAddrmandatory The IP address which is to be the destination of the traceroute request.This variable cannot be set while els10-27traceOperation is on.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.97.9.17.2.1.2
els10-27traceMaxTTLmandatory The maximum time-to-live for outgoing traceroute probe packets. This determines the number of hops that can be in a traceroute. This variable cannot be set while els10-27traceOperation is on.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.17.2.1.3
els10-27traceDataSizemandatory The size of the datagram sent with each probe. This variable cannot be set while els10-27traceOperation is on.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.17.2.1.4
els10-27traceNumProbesmandatory The number of probes which are sent for each hop. This variable cannot be set while els10-27traceOperation is on.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.17.2.1.5
els10-27traceWaitmandatory The time to wait in response to a probe. This variable cannot be set while els10-27traceOperation is on.	RFC1155-SMITimeTicksr/w Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.17.2.1.6
els10-27traceOperationmandatory Setting els10-27traceOperation to on will begin the traceroute request. Setting els10-27traceOperation to off will terminate the traceroute request.	Enumerationr/w Enumerated Values: 1 on 2 off	.1.3.6.1.4.1.97.9.17.2.1.7
els10-27traceHopmandatory The hop count for a set of probes with a particular TTL.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.17.2.1.8
els10-27traceHopAddrmandatory The IP address of the host which responded for a probe with a particular TTL.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.97.9.17.2.1.9
els10-27traceProbemandatory The probe instance for a particular hop.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.17.2.1.10
els10-27traceStatemandatory The current state of the trace probe.	Enumeration Enumerated Values: 0 not-started 1 active 2 time-exceeded 3 host-unreachable 4 net-unreachable 5 completed	.1.3.6.1.4.1.97.9.17.2.1.11
els10-27traceTimemandatory Round trip time of a probe for a particular hop.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.17.2.1.12

A table that contains information for the mirroring
on MAC addresses.

els10-27volmirrorMacEntry row .1.3.6.1.4.1.97.9.19.4.1

Information about specific unicast MAC addresses
for which mirroring will act upon.

Indexes

els10-27volmirrorIndex

Column	Syntax	OID
els10-27volmirrorIndexmandatory Entry Index	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.19.4.1.1
els10-27volmirrorMac1mandatory First MAC address for mirroring.	OctetStringr/w	.1.3.6.1.4.1.97.9.19.4.1.2

This table allows for the creation, deletion, and modification of
specific VLANs. The ports defined within this group will be members of the 'member
		 set' as defined in the IEEE 802.1Q specification.  Although this is configured 
as a table, there is only a single instance. Entries should be referenced as 
		 simple variables

els10-27VlanConfigEntry row .1.3.6.1.4.1.97.9.20.6.4.1

Allows for configuration of specific VLAN entries. Although this is configured
as a table, there is only a single instance. Entries should be referenced as
simple variables

Indexes

els10-27VlanConfigVID

Column	Syntax	OID
els10-27VlanConfigIndexmandatory The index into the table of vlans. The table has 32 entries (0 - 31). An index value outside this range will reference the local variable. For example if the index is set to -1 and the els10-27VlanConfigVID object is r…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.4.1.1
els10-27VlanConfigVIDmandatory The 12 bit VLAN Identifier associated with the configured VLAN. Valid range (1..4094)	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.4.1.2
els10-27VlanConfigPortsmandatory Each octet within the value of this object specifies a set of eight ports, with the first octet specifying ports 1 through 8, the next octet specifying ports 9 through 16, etc. Within each octet, the least significant …	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.4.1.3
els10-27VlanConfigIPmandatory The IP address to be used to access the unit on this Vlan. This must be a valid host address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.97.9.20.6.4.1.4
els10-27VlanConfigIPMaskmandatory The IP subnet mask to be used with this IP address.	RFC1155-SMIIpAddressr/w Type Constraints: range: 4	.1.3.6.1.4.1.97.9.20.6.4.1.5
els10-27VlanConfigNamemandatory The ASCII name associated with this VLAN.	OctetStringr/w Constraints: range: 1-32	.1.3.6.1.4.1.97.9.20.6.4.1.6
els10-27VlanConfigStatusmandatory A set with any value of will create, modify or delete entries in the specified VLAN according to the vlaue in els10-27VlanConfigEstablish.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.4.1.7
els10-27VlanConfigEstablishmandatory A set of the value create(1), causes an entry to be created in the els10-27VlanConfigTable as specified by the instancing information of els10-27VlanConfigVID, els10-27VlanConfigName, and els10-27VlanConfigPorts etc, …	Enumerationr/w Enumerated Values: 1 create 2 delete	.1.3.6.1.4.1.97.9.20.6.4.1.8

This table allows for the specifying of the default VLAN ID for a specific port. If
NOT configured as an 'Access' port, then packets containing this VLAN ID will have the tag
stripped on egress.  This will set the PVID for each port contained within the list.

els10-27VlanConfigEgressEntry row .1.3.6.1.4.1.97.9.20.6.5.1

Allows for configuration of specific Egress entries. Although this is configured
as a table, there is only a single instance. Entries should be referenced as
simple variables

Indexes

els10-27VlanEgressVID

Column	Syntax	OID
els10-27VlanEgressIndexmandatory The index into the Vlan table. A port must be a member of this Vlan prior to assigning this Id as the default. The table has 32 entries (0 - 31). An index value outside this range will reference the local variable. …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.5.1.1
els10-27VlanEgressVIDmandatory The 12 bit VLAN Identifier associated with the configured VLAN. Valid range (1..4094)	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.5.1.2
els10-27VlanEgressListmandatory The set of ports to which traffic destined for the VLAN specified by els10-27VlanEgressVID on the device will have this tag stripped on egress. Each octet within the value of this object specifies a set of eight ports,…	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.5.1.3
els10-27VlanEgressStatusmandatory A set with any value will change all associated entries in the els10-27VlanEgressList to have the default Vlan id set to the value in els10-27VlanEgressVID using the els10-27VlanEgressIndex vlaue to index into the tabl…	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.5.1.4

This table allows for the specifying of VLAN ID's that will be resticted from being learnt
by the device.  If a GVRP packet is received specifying this VLAN ID, it will be ignored.

els10-27VlanFilterGVRPEntry row .1.3.6.1.4.1.97.9.20.6.6.1

Allows for configuration of specific entries. Although this is configured
as a table, there is only a single instance. Entries should be referenced as
simple variables

Indexes

els10-27VlanFilterGVRPVID

Column	Syntax	OID
els10-27VlanFilterGVRPIndexmandatory The index into the Vlan Filter table. A maximum of 32 Vlan ID can be restricted from being learnt via GVRP. The table has 32 entries (0 - 31). An index value outside this range will reference the local variable. For …	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.6.1.1
els10-27VlanFilterGVRPVIDmandatory The 12 bit VLAN Identifier associated with the configured VLAN. Valid range (1..4094)	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.6.1.2
els10-27VlanFilterGVRPListmandatory The set of ports that will be restricted from leaning of a VLAN ID from a GVRP message. The VLAN ID is specified by els10-27VlanFilterGVRPVID. Each octet within the value of this object specifies a set of eight ports,…	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.6.1.3
els10-27VlanFilterGVRPStatusmandatory A set with any value enables all associated entries in els10-27VlanFilterGVRPVID table for the specified VLAN.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.6.1.4
els10-27VlanFilterGVRPEstablishVIDmandatory A set of the value create(1), will cause an entry to be created in the els10-27VlanFilterGVRPTable using els10-27VlanFilterGVRPIndex, els10-27VlanFilterGVRpVID, and els10-27VlanFilterGVRPList once a write is done to …	Enumerationr/w Enumerated Values: 1 create 2 delete	.1.3.6.1.4.1.97.9.20.6.6.1.5

Allows for configuration of specific VLAN/MAC Address entries and to specify the
port to which traffic destined for this address pair should be forwarded.  These entries
will not be aged out of the forwarding data base, but they will not be saved across
a reboot.

els10-27VlanStaticEntry row .1.3.6.1.4.1.97.9.20.6.7.1

Allows for configuration of specific entries. Although this is configured
as a table, there is only a single instance. Entries should be referenced as
simple variables

Indexes

els10-27VlanStaticVID

Column	Syntax	OID
els10-27VlanStaticVIDmandatory The 12 bit VLAN Identifier associated with the configured VLAN. Valid range (1..4094)	OctetStringr/w Constraints: range: 1-8	.1.3.6.1.4.1.97.9.20.6.7.1.1
els10-27VlanStaticMACmandatory The media dependent physical address.	SNMPv2-TCPhysAddressr/w Description: Represents media- or physical-level addresses.	.1.3.6.1.4.1.97.9.20.6.7.1.2
els10-27VlanStaticPortmandatory An integer designating the port number to associate this address to.	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.20.6.7.1.3
els10-27VlanStaticEstablishmandatory A set of the value create(1), causes an entry to be created as specified by the instancing information of els10-27VlanSaticVID, els10-27VlanStaticMAC, and els10-27VlanStaticPort. A set of delete(2) causes the specif…	Enumerationr/w Enumerated Values: 1 create 2 delete	.1.3.6.1.4.1.97.9.20.6.7.1.4

The (conceptual) table listing the IP multicast groups
for which there are members on a particular interface.

els10-27igmpCacheEntry row .1.3.6.1.4.1.97.9.22.5.1

An entry (conceptual row) in the els10-27igmpCacheTable.

Indexes

els10-27igmpCacheAddress els10-27igmpCacheIfIndex

Column	Syntax	OID
els10-27igmpCacheAddressmandatory The IP multicast group address for which this entry contains information.	RFC1155-SMIIpAddress Type Constraints: range: 4	.1.3.6.1.4.1.97.9.22.5.1.1
els10-27igmpCacheIfIndexmandatory The interface for which this entry contains infor- mation for an IP multicast group address.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.22.5.1.2
els10-27igmpCacheExpiryTimemandatory The minimum amount of time remaining before this entry will be aged out.	RFC1155-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.97.9.22.5.1.3

Provides a list of control objects over flow control parameters.

els10-27FlowControlEntry row .1.3.6.1.4.1.97.9.23.4.1

Defines a particular entry containing objects pertaining to
definition and control over flow control ports.

Indexes

els10-27FlowControlInterface

Column	Syntax	OID
els10-27FlowControlInterfacemandatory The MIB2 interface for which this flow control information pertains	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.23.4.1.1
els10-27FlowControlEnablemandatory Control 802.3x flow control on a per interface basis. On (1), Off (2)	Integer32r/w Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.23.4.1.2
els10-27FlowControlRxPauseFramesmandatory The number of pause frames received on this interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.23.4.1.3
els10-27FlowControlTxPauseFramesmandatory The number of pause frames transmitted on this interface.	Integer32 Type Constraints: range: -2147483648..2147483647	.1.3.6.1.4.1.97.9.23.4.1.4