CONTIVITY-TRAPS-V1-MIB

A coldStart trap signifies that the SNMPv2 entity, acting
in an agent role, is reinitializing itself and that its
configuration may have been altered.

A linkDown trap signifies that the sending
protocol entity recognizes a failure in one of
the communication links represented in the
agent's configuration.
Varbind list:
ifIndex -- ifIndex of the interface.
ifAdminStatus -- ifAdminStatus of the interface.
ifOperStatus -- ifOperStatus of the interface.
ifDescr -- ifDescr of the interface.
ifType -- ifType, this provides descrimination of interfaces that are tunnels.
ifReasonForStatus-ces -- reason for the change in status.
ifPhysLocation-ces -- this is the slot number.
ifPhysRelPos-ces -- the port number on the board defined in interfacePhysLocation.
ifIpAddr-ces -- IP address assigned to the phys port or the local IP address of a tunnel.
ifName-ces -- Name of the tunnel or physical interface.
ifTunnelRemoteIpAddr-ces -- for non-tunnel interfaces it is zero.
sysObjectID -- sysObjectID of the unit.
sysName -- sysName of the unit.

A linkUp trap signifies that the sending
protocol entity recognizes that one of the
communication links represented in the agent's
configuration has come up.
Varbind list:
ifIndex -- ifIndex of the interface.
ifAdminStatus -- ifAdminStatus of the interface.
ifOperStatus -- ifOperStatus of the interface.
ifDescr -- ifDescr of the interface.
ifType -- ifType, this provides descrimination of interfaces that are tunnels.
ifReasonForStatus-ces -- reason for the change in status
ifPhysLocation-ces -- this is the slot number.
ifPhysRelPos-ces -- the port number on the board defined in interfacePhysLocation.
ifIpAddr-ces -- IP address assigned to the phys port or the local IP address of a tunnel.
ifName-ces -- Name of the tunnel or physical interface.
ifTunnelRemoteIpAddr-ces -- for non-tunnel interfaces it is zero.
sysObjectID -- sysObjectID of the unit.
sysName -- sysName of the unit.

An authenticationFailure trap signifies that the SNMPv2
entity, acting in an agent role, has received a protocol
message that is not properly authenticated.
The snmpEnableAuthenTraps object indicates
whether this trap will be generated.

snmpAuthenOperation-ces identifies the operation( ie. GetRequest,
GetNextRequest,... ) was being attempted.
snmpAuthenIpAddress-ces identifies the source IP address of
the operation.
snmpAuthenCommString-ces identifies the community string that
was used in the operation.

Power Up

Periodic Heartbeat

Hard Disk Number 1 Status

Status of -5 Volt power

Status of +3 Volt power

Status of 2.5VA power

Status of 2.5VB power

Status of +12 Volt power

Status of -12 Volt power

Status of the normal temperature reading

Status of the critical temperature reading

The chassis intrusion sensor indicates that the unit has been physically opened

Status of the redundant power supplies

Hard Disk Number 0 Status

Status of T1 WAN card(s).
Possible Values:
For Wanic support:
Alert: Invalid Device X
Warning: Device WanicX disabled
Alert: Device WanicX down
Warning: Device WanicX not initialized
Warning: Device WanicX PPP negotiating
Alert: Device WanicX PPP down
Alert: Device WanicX FR no support
Alert: Device WanicX Unknown DL
For T1:
Alert: Invalid Device X
Warning: Device LMCDTEX disabled
Alert: Device LMCDTEX down
Warning: Device LMCDTEX not initialized
For CSU/DSU:
Alert: Invalid Device X
Warning: Device LMCCDX disabled
Alert: Device LMCCDX down
Warning: Device LMCCDX not initialized

Status of T3 WAN card
Possible Values:
Alert: Invalid Index X
Warning: Device HSSIX disabled
Alert: Device HSSIX down
Warning: Device HSSIX not initialized
Alert: Device HSSIX PPP down
Warning: Device HSSIX PP initializing

Status of hardware accelerator card.
Possible Values:
Invalid hardware accelerator unit %d;
Unknown hardware accelerator unit %d;
Healthy: Bulk Accelerator in slot %d: Unit %d Status 1 - ATTACHED;
Warning: Bulk Accelerator in slot %d: Unit %d Status 2 - DISABLED;
Healthy: Bulk Accelerator in slot %d: Unit %d Status 3 - ACTIVE;
Warning: Bulk Accelerator in slot %d: Unit %d Status 4 - RECOVERING;
Warning: Bulk Accelerator in slot %d: Unit %d Status 5 - SHUTDOWN;
Alert: Bulk Accelerator in slot %d: Unit %d Status 6 - FAILED;

Status of V.90 Interface card
Possible Values:
Please note that X corresponds to the unit number of the card.
Alert: V.90 Invalid index X
Disabled: Device IntModem-X disabled
Healthy: Device IntModem-X: PPP is UP.
Alert: Device IntModem-X down
Warning: Device IntModem-X not initialized
Alert: Device IntModem-X: Call is UP. Internal Error.
Warning: Device IntModem-X is Down. Last dial-out attempt FAILED.
Healthy: Device IntModem-X is Down (No Active calls)
Warning: Device IntModem-X is in an UNKNOWN state

Status of V.90 Interface card
Possible Values:
Please note that X corresponds to the unit number of the card.
Alert: BRI Invalid index X
Alert: Device BRI-X not Responding. Needs Host Reboot.
Disabled: Device BRI-X disabled
Alert: Device BRI-X down
Warning: Device BRI-X not initialized
Healthy: Device BRI-X: PPP is UP.
Alert: Device BRI-X: Call is UP. Internal Error.
Warning: Device BRI-X is Down. Last dial-out attempt FAILED.
Healthy: Device BRI-X is Down (No Active calls)
Alert: Device BRI-X is in an UNKNOWN state

Status of Serial (COM) port/interface
Possible Values:
Please note that X corresponds to the unit number of the serial interface
Alert: COM port Invalid index X
Healthy: Device COMX is set for Serial Menu.
Disabled: Device COMX disabled
Warning: Device COMX not initialized
Healthy: Device COMX: PPP is UP.
Alert: Device COMX: Call is UP. Internal Error.
Warning: Device COMX is Down. Last dial-out attempt FAILED.
Healthy: Device COMX is Down (No Active calls)
Alert: Device COMX is in an UNKNOWN state

Status of ADI ADSL card
Possible Values:
Please note that X corresponds to the unit number of the serial interface
Alert: Invalid index X
Alert: Device ADIADSLX off line
Disabled: Device ADIADSLX disabled
Alert: Device ADIADSLX down
Warning: Device ADIADSLX not initialized
Healthy: Device ADIADSLX up

Memory Usage Status

Status of any LAN cards on the system

Status of second CPU.

Status of the first CPU fan

Status of the second CPU fan

Status of the chassis fan.

Status of the +5 Volt power

An event sent at the user's request to signal that a rule has
been matched.

firewallPolicyType-ces -- Policy type.
firewallRuleType-ces -- Type of rule that triggered this event.
firewallRuleNumber-ces -- Number of the rule that triggered this event.
ifIndex -- ifIndex is the index into the ifTable for port that received the packet.
ifName-ces -- The name of the interface, same as ifName.
firewallSrcAddr-ces -- Source IP address of the packet.
firewallSrcPort-ces -- Source port address of the packet.
firewallDestAddr-ces -- Destination IP address of the packet.
firewallDestPort-ces -- Destination port of the packet.
firewallProtocolID-ces -- The value of the protocol field in the IP header.
firewallRuleAction-ces -- Action defined for the triggered rule.

Status of External Radius Accounting Server

Status of Radius Authentication Server

Status of Certificates Validity
Possible Values:
Healthy: Certificates Validity: Operational;
Alert: Certificates Validity: All certificates are going to expire/expired;
Warning: Certificates Validity: One/more certificate is invalid;
Disabled: Certificates Validity: No certificate defined;

Status of External LDAP Authentication Server.
Possible Values:
Warning: External LDAP Authentication Server: Server is down(indicates at least one server is not reachable and at least one server is reachable);
Alert: External LDAP Authentication Server: Server is down(indicates all servers are not reachable);

Status of CMP Server.
Possible Values:
One/more Certificate Requests error: there is at least one request error;
One/more Certificate Requests processing: there is at least one request in processing;
No Certificate Requests submitted: there is no request sent;

Status of DHCP Server
Possible Values:
Disabled: DHCP Server is Disabled
Alert: DHCP Server is NOT configured
Alert: DHCP Server is configured and operational, Using backup config
Alert: No IP Address available for subnet
Alert: DHCP Server is configured and server is DOWN
Healthy: DHCP Server is Operational
Warning: Subnet low on IP Addresses
Warning: DHCP Server Initializing
Warning: DHCP Server is Enabled, but status Unknown cannot be determined

Status of SSH Server.

Status of NTP Server.

Status of OSPF Server.

Status of Circuitless IP.

Status of DHCP Relay Server.

Status of External Disk Backup Server

Status of Global Demand Services Services.

Status of Demand Interface.

Status of CRL Server.

Status of OCSP Server.

Status of Local Disk Redundency

Status of Internal LDAP Server

Status of Load Balancing Server

Status of DNS Server

Status of SNMP Server

Status of the IP address pool

Status of External LDAP Server

Network buffer usage

Status of Multicast Relay

Status of DLSW Server

Status of IPsec Failover service

Status of TunnelGuard

Status of RIP Server

Status of Route Policy

Status of Client Routes Marshaler

Status of IGMP Server

Status of internal firewall

Status of FIPS

Status temporary SW Licenses

Status of Network Address Translator

Status of Anti Spoofing Feature

Status of SSL-VPN Accelerator

Status of User Ip Address Pool server

Status of VRRP Server

Failed Login Attempt

Security Intrusion