CISCO-XGCP-EXT-MIB Table View

Table-centric layout grouping table, row, and column objects.

Standard view Table view

Tables

Rows

Columns

cxeCallCtrlConfigTable

table

.1.3.6.1.4.1.9.9.325.1.1.1 · 1 row entry · 22 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cxeCallCtrlConfigTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-XGCP-EXT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-XGCP-EXT-MIB::cxeCallCtrlConfigTable'

This table contains objects used for configuring general 
parameters in call control default to the local media gateway
in xGCP protocols.

cxeCallCtrlConfigEntry row .1.3.6.1.4.1.9.9.325.1.1.1.1

There is one entry for each media gateway.
The entry will be automatically generated when a media
gateway is detected.

Indexes

CISCO-MEDIA-GATEWAY-MIBcmgwIndex

Column Syntax OID

cxeCallCtrlControlServiceType

This object identifies Type Of Service (TOS) field of
IP header for the control packet in VoIP application.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.9.9.325.1.1.1.1.1

cxeCallCtrlBearerServiceType

This object identifies Type Of Service (TOS) field
of IP header for the voice payload packet in VoIP
application.

Integer32r/w

Constraints:
range: 0-255

.1.3.6.1.4.1.9.9.325.1.1.1.1.2

cxeCallCtrlVoIpDtmfRelayMode

This object defines whether the DTMF (Dual Tone,
Multi-Frequency) digits need to be transported to the other
endpoint via NSE packets in Voice Over IP.

The value of this object will be utilized when the …

DtmfRelayModer/w

Type Values:

1	dtmfRelayDisabled
2	dtmfRelayCisco
3	dtmfRelayNse
4	dtmfRelayOutOfBand
5	dtmfRelayNteGw
6	dtmfRelayNteCa
7	dtmfRelayInband
8	dtmfRelayType3

.1.3.6.1.4.1.9.9.325.1.1.1.1.3

cxeCallCtrlVoIpDtmfCodec

This object identifies DTMF relay codec for VoIP.
This object is not applicable if cxeCallCtrlVoIpDtmfRelay
is DtmfRelayDisabled.

DtmfCodecTyper/w

Type Values:

1	dtmfCodecAll
2	dtmfCodecLowRate

.1.3.6.1.4.1.9.9.325.1.1.1.1.4

cxeCallCtrlVoAal2DtmfRelayMode

This object defines whether the DTMF (Dual Tone,
Multi-Frequency) digits need to be transported to the other
endpoint in Voice over AAL2 packets.

The value of this object will be utilized when the call
a…

DtmfRelayModer/w

Type Values:

1	dtmfRelayDisabled
2	dtmfRelayCisco
3	dtmfRelayNse
4	dtmfRelayOutOfBand
5	dtmfRelayNteGw
6	dtmfRelayNteCa
7	dtmfRelayInband
8	dtmfRelayType3

.1.3.6.1.4.1.9.9.325.1.1.1.1.5

cxeCallCtrlVoAal2DtmfCodec

This object identifies DTMF relay CODEC for Voice over AAL2.
This object is not applicable if cxeCallCtrlVoAal2DtmfRelay
is DtmfRelayDisabled.

DtmfCodecTyper/w

Type Values:

1	dtmfCodecAll
2	dtmfCodecLowRate

.1.3.6.1.4.1.9.9.325.1.1.1.1.6

cxeCallCtrlTsePayload

This object identifies TSE (Telephony Signaling
Events) payload type.

Integer32r/w

Constraints:
range: 0-200

.1.3.6.1.4.1.9.9.325.1.1.1.1.7

cxeCallCtrlNetNseTimer

This object identifies Network Signaling Event (NSE)
timeout value.

millisecondsInteger32r/w

Constraints:
range: 250-10000

.1.3.6.1.4.1.9.9.325.1.1.1.1.8

cxeCallCtrlRtcpRcvTimer

This object identifies the number of times of Real Time
Control Transport (RTCP) report interval if the media
gateway has not recieved any RTCP packets from another
side.

The media gateway will mark anot…

timesInteger32r/w

Constraints:
range: 1-10

.1.3.6.1.4.1.9.9.325.1.1.1.1.9

cxeCallCtrlIgnoreAal2LcoCodec

This object defines whether to ignore the AAL2 Local
Connection Option (LCO) message from the call agent
or not.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.1.1.10

cxeCallCtrlDigitMapOrder

This object defines the type of digit map order.
The MGC can advise and load the gateway with a digit map
that correspond to the dial plan to collect the access
codes, credit card numbers and other numbers requested
…

Enumerationr/w

Enumerated Values:

1	dmOrderShortest
2	dmOrderOrdered

.1.3.6.1.4.1.9.9.325.1.1.1.1.11

cxeCallCtrlT38Inhibited

This object defines whether T.38 is inhibited in the
media gateway or not.

T.38 is a Fax Relay Protocol defined by ITU for
real-time protocol for Fax over IP networks.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.1.1.12

cxeCallCtrlT38NseRspTimer

This object defines a timeout value for a timer.
This timer is started after sending a NSE 200
while waiting for the NSE 201 acknowledgement or
NSE 202 negative acknowledgement. Expiration of the
timer will indicate …

millisecondsInteger32r/w

Constraints:
range: 250-10000

.1.3.6.1.4.1.9.9.325.1.1.1.1.13

cxeCallCtrlT38FecEnabled

This object is used to enable the Forward Error
Correction (FEC) for UDP-based fax transport.

This object is not applicable if cxeCallCtrlT38Inhibited
is set to 'true'.

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.1.1.14

cxeCallCtrlT38LsRedundancy

This object determines the extent of the Internet Fax
Protocol (IFP) packet transmission redundancy for
the low-speed control information exchanged during
the first phase of a T.38 fax relay connection.
…

Integer32r/w

Constraints:
range: 0-5

.1.3.6.1.4.1.9.9.325.1.1.1.1.15

cxeCallCtrlT38HsRedundancy

This object determines the extent of the Internet Fax
Protocol (IFP) packet transmission redundancy for
the high-speed control and image information
exchanged following the initial low-speed phase of
a T.38 fax relay…

Integer32r/w

Constraints:
range: 0-2

.1.3.6.1.4.1.9.9.325.1.1.1.1.16

cxeCallCtrlT38NsfCountryCode

This object specifies the country code for identifying
the country where the media gateway with non-standard
capabilities was manufactured.

This object is not applicable if cxeCallCtrlT38Inhibited
is se…

CISCO-TCCountryCodeITUr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.325.1.1.1.1.17

cxeCallCtrlT38NsfVendorCode

Per its definition (ITU T.35), the Vendor Code (also
called the Terminal Provider Code) in the Non-Standard
Facilities (NSF) code is a two-byte field identifying the
manufacturer of the media gateway with non-standard
…

CxeTerminalProviderCoder/w

Type Constraints:
range: 0
range: 2

.1.3.6.1.4.1.9.9.325.1.1.1.1.18

cxeCallCtrlVselDselFselSupport

This object is used to enable or disable VSEL, DSEL and
FSEL support.

VSEL: Voice codec, packet length and packet times Selection
DSEL: Data codec, packet length and packet times Selection
FSEL: Fax co…

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.1.1.19

cxeCallCtrlDefaultBearTraffic

This object specifies the combination of the network
type (IP/ATM), virtual circuit type (PVC/SVC) and
ATM adaptation layer type (AAL1/AAL2/AAL5) for the
connection used in transporting bearer traffic.

…

Enumerationr/w

Enumerated Values:

1	ipPvcAal5
2	atmPvcAal2
3	atmSvcAal2
4	atmSvcAal1

.1.3.6.1.4.1.9.9.325.1.1.1.1.20

cxeCallCtrlLastFailedMgcAddrType

This object indicates the address type, either IPv4 or
IPv6, of cxeCallCtrlLastFailedMgcAddress.

INET-ADDRESS-MIBInetAddressType

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.325.1.1.1.1.21

cxeCallCtrlLastFailedMgcAddress

This object indicates the address of MGC (Media Gateway
Controller) with which the media gateway had tried to
communicate lastly but failed.

INET-ADDRESS-MIBInetAddress

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.325.1.1.1.1.22

cxeCallCtrlProfileTable

table

.1.3.6.1.4.1.9.9.325.1.1.2 · 1 row entry · 31 columns

Open in standard view

Uses the cisco variant from /opt/observium/mibs/cisco.

Command help

Walk cxeCallCtrlProfileTable

/usr/bin/snmpbulkwalk -v2c -c '<community>' -Pud -Ir -OQUs -m 'CISCO-XGCP-EXT-MIB' -M '/opt/observium/mibs/cisco:/opt/observium/mibs/rfc:/opt/observium/mibs/net-snmp' 'udp:<hostname>:161' 'CISCO-XGCP-EXT-MIB::cxeCallCtrlProfileTable'

This table defines the call control profiles.
          
A call control profile contains the call control information 
that a call agent uses to establish a call. In the call 
control profile, it has the following configurations:
(1) The information of call agent, such as its address, 
    connecting port, service type and version.
(2) The maximum retry parameters in the message exchange 
    between the call agent and the media gateway.
(3) The timeout settings in the call control.
          
A call control profile can be associated with a voice
interface (DS0 group in TDM side), so all the calls set up
in the voice interface will use the call control 
parameters from the profile. 
          
A call control profile can be associated with a Media Gateway
Controller(MGC)/call agent redundant group (cMgcGrpParamTable
defined in CISCO-MGC-MIB). In this case, the call agent 
information for the profile will be determined by the MGC 
redundant group.

cxeCallCtrlProfileEntry row .1.3.6.1.4.1.9.9.325.1.1.2.1

Each entry describes an instance of a call control
profile in the media gateway.

When an entry of call control profile is added to the table,
the following object must be provided:

cxeCcPr…

Indexes

CISCO-MEDIA-GATEWAY-MIBcmgwIndex cxeCcProfileIndex

Column Syntax OID

cxeCcProfileIndex

This object uniquely identifies the call control profile.

CISCO-MEDIA-GATEWAY-MIBCCallControlProfileIndex

Type Constraints:
range: 1..65535

.1.3.6.1.4.1.9.9.325.1.1.2.1.1

cxeCcProfileName

A unique name for the profile. The name of the profile
has to be unique among all entries of the table.

This object is mandatory during the creation of the entry.

This object can not be mod…

OctetStringr/w

Constraints:
range: 1-64

.1.3.6.1.4.1.9.9.325.1.1.2.1.2

cxeCcProfileNumVifs

This object reprsents the total number of voice interface
(DS0 group) associated with this call control profile.

The value of '0' means there is no voice interfaces
associated with the profile.
…

Integer32

Constraints:
range: 0-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.3

cxeCcProfileMgcGrpNum

This object indicates which MGC Redundant group number
that the call control profile will be used.
The value is the index to MGC Redundant Group Table
(cMgcGrpParamTable).

There are two conditions for as…

Integer32r/w

Constraints:
range: 0-128

.1.3.6.1.4.1.9.9.325.1.1.2.1.4

cxeCcProfileMgcAddrType

This object identifies the address type applicable to
cxeCcProfileMgcAddress.

INET-ADDRESS-MIBInetAddressTyper/w

Type Values:

0	unknown
1	ipv4
2	ipv6
3	ipv4z
4	ipv6z
16	dns
25	l2vpn

.1.3.6.1.4.1.9.9.325.1.1.2.1.5

cxeCcProfileMgcAddress

This object specifies the address of Media Gateway
Controller (MGC) configured in the profile.

When cxeCcProfileMgcGrpNum is non-zero (which menas
using MGC group), this object can not be set.

INET-ADDRESS-MIBInetAddressr/w

Type Constraints:
range: 0..255

.1.3.6.1.4.1.9.9.325.1.1.2.1.6

cxeCcProfileProtocolIdx

This object specifies the protocol that the media gateway
should communicate with MGC during call setup.

It is the index of the protocol table(cMediaGwProtocolTable).

If cxeCcProfileMgcGrpN…

Integer32r/w

Constraints:
range: 1-32

.1.3.6.1.4.1.9.9.325.1.1.2.1.7

cxeCcProfileXgcpRetryMethod

This object specifies the command/response retry method
when the media gateway communicates with the MGC in
xGCP protocols.

CISCO-XGCP-MIBCXgcpRetryMethodr/w

Type Values:

1	neverResetTimer
2	resetTimerForNewMgc
3	resetTimerForNewAddr
4	resetTimerForEndpoint

.1.3.6.1.4.1.9.9.325.1.1.2.1.8

cxeCcProfileRetryMax1

This object contains the suspicious error threshold for
signaling messages.

Integer32r/w

Constraints:
range: 1-20

.1.3.6.1.4.1.9.9.325.1.1.2.1.9

cxeCcProfileDnsLookupMax1

This object enables/disables the Max1 Domain Name Server
(DNS) query operation when Max1 expires.
This object is used when a gateway-initiated message is not
acknowledged by the MGC. If the object is 'true', a DNS
query…

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.2.1.10

cxeCcProfileRetryMax2

This object contains the disconnect error threshold
for signaling messages.

Integer32r/w

Constraints:
range: 1-20

.1.3.6.1.4.1.9.9.325.1.1.2.1.11

cxeCcProfileDnsLookupMax2

This object enables/disables the Max2 Domain Name Server
(DNS) query operation when Max2 expires.

This object is used when a gateway-initiated message is not
acknowledged by the MGC. If the object is 'tru…

SNMPv2-TCTruthValuer/w

Type Values:

1	true
2	false

Description:

Represents a boolean value.

.1.3.6.1.4.1.9.9.325.1.1.2.1.12

cxeCcProfileMwiTimeout

The timeout value for the message waiting indicator tone.
Message Waiting Indicator (MWI) tone is used with message
waiting services, it indicates that the media gateway
is ready to accept address information or other …

millisecondsInteger32r/w

Constraints:
range: 1-50

.1.3.6.1.4.1.9.9.325.1.1.2.1.13

cxeCcProfileTsmaxTimeout

The timeout value for retransmission removal.
The gateway uses the value of this object to determine how
long for the MGCP messages stored in the retransmission
queue before they are discarded.

secondsInteger32r/w

Constraints:
range: 1-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.14

cxeCcProfileTdinitTimeout

The voice interface (DS0 group) becomes disconnected when
the media gateway tries to communicate with the call agent
and the retransmission procedure times out after retrying.

The voice interface (DS0 …

secondsInteger32r/w

Constraints:
range: 1-100

.1.3.6.1.4.1.9.9.325.1.1.2.1.15

cxeCcProfileTdminTimeout

The DS0 group (voice interface) becomes disconnected
when it tries to communicate with the call agent and the
retransmission procedure times out after retrying.

The DS0 group (voice interface ) in disc…

secondsInteger32r/w

Constraints:
range: 1-100

.1.3.6.1.4.1.9.9.325.1.1.2.1.17

cxeCcProfileTdmaxTimeout

The maximum waiting delay (Tdmax) timeout value used by the
media gateway to send the Restart In Progress with the
restart method as RM:disconnected to the call agent when
the voice interface associated ds0-group disco…

secondsInteger32r/w

Constraints:
range: 1-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.18

cxeCcProfileTcritTimeout

This object represents the timeout value for the critical
timer.

If used along with a digit map, the timer is started when
the last digit is received. i.e and when no more digits
are required for a digit…

secondsInteger32r/w

Constraints:
range: 1-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.19

cxeCcProfileTparTimeout

This object represents the partial dial timeout
and is used along with a digit map as the inter-digit
timer.
This object is used by call processing when it processes
mid-call DTMF digit reporting.

The …

secondsInteger32r/w

Constraints:
range: 1-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.20

cxeCcProfileThistTimeout

The MGCP protocol is organized as set of transactions, each
of which is composed of a command and a resonse. The MGCP
messages, being carried over UDP, may be subject to losses.
In the absence of a timely response, comm…

secondsInteger32r/w

Constraints:
range: 1-1000

.1.3.6.1.4.1.9.9.325.1.1.2.1.21

cxeCcProfileRtTimeout

This object specifies time for which the local ring back
tone (towards the TDM) will be generated unless
interrupted (e.g., by the answer from the called party
or a delete connection command from the Call Agent).
…

secondsInteger32r/w