CISCO-XDSL-LINE-MIB Table View

This table contains enterprise-specific line parameters
for XTU-C class xDSL devices supported by the system.

cXdslLineEntry row .1.3.6.1.4.1.9.9.204.1.1.1

A set of enterprise-specific xDSL line parameters for an
XTU-C class device.
There exists an entry for each ifEntry with an ifType of
xDSL such as adsl, sdsl, idsl, etc. that are supported by
the system.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cXdslLineTimeSinceLastChange Represents the time elapsed since the status of this interface was last changed.	SNMPv2-SMITimeTicks Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.204.1.1.1.1
cXdslLineNoOfChanges Represents the number of changes of the interface status since last reset of the agent or since a XTU-C modem was installed.	SNMPv2-SMICounter32 Type Constraints: range: 0..4294967295	.1.3.6.1.4.1.9.9.204.1.1.1.2

This table contains enterprise-specific test
parameters initiated by the XTU-C class devices
supported by the system.

cXdslTestEntry row .1.3.6.1.4.1.9.9.204.1.2.1

A set of enterprise-specific test parameters for an
XTU-C class xDSL device.
There exists an entry for each ifEntry with an ifType of
xDSL such as adsl, sdsl, idsl, etc. that are supported by
the system.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cXdslTestStatus Represents status of the test per port. Once a test is completed or aborted, the status remains at passed, failed, or aborted until user clears it by setting cXdslTestTrigger to clear or starts a new test. This object …	Enumeration Enumerated Values: 1 inactive 2 active 3 passed 4 failed 5 aborted	.1.3.6.1.4.1.9.9.204.1.2.1.1
cXdslTestType The type of test to be performed. The test duration is determined by cXdslTestTime. All the test types inhibit the service on that line. The agent will only change cXdslTestType, if no test is active on the targeted por…	Enumerationr/w Enumerated Values: 1 none 2 bertDigitalLocal 3 bertAnalogLocal 4 bertDigitalRemote 5 bertAnalogRemote 6 other	.1.3.6.1.4.1.9.9.204.1.2.1.2
cXdslTestTrigger Starts, stops (aborts) a test in progress or clears the test results. The agent will only start a new test, if no test is active on the targeted port. The value of this object returns 'ready' when read, the value canno…	Enumerationr/w Enumerated Values: 1 stop 2 start 3 clear 4 ready	.1.3.6.1.4.1.9.9.204.1.2.1.3
cXdslTestTime Test duration. Time interval between 1 - 30 minutes.	minutesInteger32r/w Constraints: range: 1-30	.1.3.6.1.4.1.9.9.204.1.2.1.4
cXdslTestBertErrors Errors during BERT test. The test will abort if any BERT errors occur. Note: that even if there are no BERT errors the test can still fail due to BertBitErrors. Bit Description --- -…	Bits Enumerated Values: 0 noError 1 cpeBertAborted 2 lostCpeSync 3 noCpeSync 4 noCpeResults 5 coBertAborted 6 lostCoSync 7 noCoSync	.1.3.6.1.4.1.9.9.204.1.2.1.5
cXdslTestBertBitErrors This value represents the number of BERT bit errors accumulated during the test duration, the value may not be available until completion of the test. The test will fail if this value is greater than 0.	Unsigned32 Constraints: range: 0-2147483647	.1.3.6.1.4.1.9.9.204.1.2.1.6
cXdslTestBertRunTime This value represents the BERT run time in seconds, the value may not be available until completion of the test.	secondsInteger32 Constraints: range: 0-1800	.1.3.6.1.4.1.9.9.204.1.2.1.7
cXdslTestBertBitRate This value represents the BERT bitrate in bps that was detected during the BERT test, the value may not be available until completion of the test.	bpsInteger32 Constraints: range: 0-20000000	.1.3.6.1.4.1.9.9.204.1.2.1.8

This table contains enterprise-specific mode 
parameters initiated by the XTU-C class devices
supported by the system.

cXdslModeEntry row .1.3.6.1.4.1.9.9.204.1.3.1

A set of enterprise-specific mode parameters for an
XTU-C class xDSL device.
There exists an entry for each ifEntry with an ifType of
xDSL such as adsl, sdsl, idsl, etc. that are supported by
the system.

Indexes

IF-MIBifIndex

Column	Syntax	OID
cXdslModeLoopback The value of this object specifies the loopback mode of this interface. The interface will stay in loopback mode until this object is set to disabled. The XTU-C may support other mode types that are not defined in this …	Enumerationr/w Enumerated Values: 1 disabled 2 loopbackAnalogLocal 3 loopbackDigitalLocal 4 loopbackAnalogRemote 5 loopbackDigitalRemote 6 other	.1.3.6.1.4.1.9.9.204.1.3.1.1
cXdslModeSpectrum The value of this object specifies the spectrum mode of this interface. The interface will stay in spectrum mode until this object is set to disabled. The modes will inhibit the service on that line. Not all spectrum mo…	Enumerationr/w Enumerated Values: 1 disabled 2 spectrum1 3 spectrum2 4 spectrum3 5 spectrum4 6 spectrum5 7 spectrum6	.1.3.6.1.4.1.9.9.204.1.3.1.2

This table extends the adslLineConfProfileTable and contains
enterprise-specific xDSL configuration information. Entries in
this table apply to more than one type of DSL modems

cXdslLineConfProfileEntry row .1.3.6.1.4.1.9.9.204.1.4.1

A configuration profile containing enterprise-specific xDSL
line configuration information.
An entry exist in this table for every profile created by
adslLineConfProfileRowStatus which will also modify or
delete an …

Indexes

No indexes recorded

Column	Syntax	OID
cXdslLineConfPayloadScrambled This object specifies whether ATM Payload Scrambling is enabled for this profile.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.204.1.4.1.1
cXdslLineConfAlarmsEnabled This object specifies whether Alarms are enabled for this profile.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.204.1.4.1.2
cXdslLineConfLinkUpDownTrap This object specifies whether Link Up/Down traps are enabled for this profile.	SNMPv2-TCTruthValuer/w Type Values: 1 true 2 false Description: Represents a boolean value.	.1.3.6.1.4.1.9.9.204.1.4.1.3